TI UC1907J883B

 SLUS165C – MARCH 1999 - REVISED JANUARY 2002
FEATURES
D Fully Differential High Impedance Voltage
Sensing
SOIC-16 DW PACKAGE
(TOP VIEW)
C/S OUT
C/S (+)
C/S (–)
(–) SENSE
POWER RETURN
ARTIFICIAL GND
VREF
ISET
D Accurate Current Amplifier for Precise
C/S (–)
2
1
CURRENT SHARE BUS
N/C
3
STATUS INDICATE
C/S OUT
PLCC-20, LCC-20,
Q OR L PACKAGE
(TOP VIEW)
C/S (+)
D
D
D
D
Current Sharing
Opto Coupler Driving Capability
1.25% Trimmed Reference
Master Status Indication
4.5-V to 35-V Operation
20 19
18
ADJ OUT
(–) SENSE
5
17
ADJ INPUT
N/C
6
16
POWER RETURN
7
15
8
14
VCC
N/C
OPTO DRIVE
DESCRIPTION
ISET
VREF
9 10 11 12 13
16
15
14
13
12
11
10
9
STATUS INDICATE
CURRENT SHARE BUS
ADJ OUT
ADJ INPUT
COMP
(+) SENSE
VCC
OPTO DRIVE
DIL-16 J or N PACKAGE
(TOP VIEW)
4
ARTIFICIAL GND
1
2
3
4
5
6
7
8
N/C
COMP
(+) SENSE
C/S OUT
C/S (+)
C/S (–)
(–) SENSE
POWER RETURN
ARTIFICIAL GND
VREF
ISET
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
STATUS INDICATE
CURRENT SHARE BUS
ADJ OUT
ADJ INPUT
COMP
(+) SENSE
VCC
OPTO DRIVE
The UCx907 family of load share controller ICs provides all the necessary features to allow
multiple-independent-power modules to be paralleled such that each module supplies only its proportionate share
to total-load current.
This sharing is accomplished by controlling each module’s power stage with a command generated from a
voltage-feedback amplifier whose reference can be independently adjusted in response to a common-share-bus
voltage. By monitoring the current from each module, the current share bus circuitry determines which paralleled
module would normally have the highest output current and, with the designation of this unit as the master, adjusts
all the other modules to increase their output current to within 2.5% of that of the master.
The current share bus signal interconnecting all the paralleled modules is a low-impedance, noise-insensitive line
which will not interfere with allowing each module to act independently should the bus become open or shorted to
ground. The UC3907 controller will reside on the output side of each power module and its overall function is to supply
a voltage feedback loop. The specific architecture of the power stage is unimportant. Either switching or linear designs
may be utilized and the control signal may be either directly coupled or isolated though the use of an optocoupler or
other isolated medium.
Other features of the UC3907 include 1.25% accurate reference: a low-loss, fixed-gain current-sense amplifier, a fully
differential, high-impedance voltage sensing capability, and a status indicator to designate which module is
performing as master.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2000, Texas Instruments Incorporated
!"# $"%&! '#(
'"! ! $#!! $# )# # #* "#
'' +,( '"! $!# - '# #!# &, !&"'#
# - && $## (
www.ti.com
1
SLUS165C – MARCH 1999 - REVISED JANUARY 2002
block diagram
VOLTAGE ERROR AMPLIFIER
(+) SENSE
11
+
12
V CC
1.75 V
0.25 V
GROUND
AMPLIFIER
(–) SENSE
4
POWER RTN
5
9
OPTO DRIVE
V REF
1.75 V
–
GND
+
8
ISET
+
DRV
–
1 kΩ
20 k Ω
50 kΩ
ADJUST
AMPLIFIER
6
14
ADJ OUT
13
ADJ INPUT
15
CURRENT SHARE BUS
16
STATUS INDICATE
50 mV
+
ARTIFICIAL GND
DRIVE
1.0 V AMPLIFIER
COMP
+
+
VCC (4.5 V TO 35 V) 10
–
VREF
7
C/S OUT
1
17.5 kΩ
–
ADJ
+
40 kΩ
2 kΩ
C/S (–)
3
–
2 kΩ
C/S (+)
BUFFER
AMPLIFIER
CURRENT SENSE
AMPLIFIER
100
–
+
+
2
10 k Ω
40 k Ω
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 V
Opto out voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 V
Opto out current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
Status indicate sink current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
C/S input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 V
Share bus voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 35 V
Other analog inputs and outputs (zener clamped) maximum forced voltage . . . . . . . . . . . . . . . . –0.3 V to10 V
Other analog inputs and outputs (zener clamped) maximum forced current . . . . . . . . . . . . . . . . . . . . . ±10 mA
Ground amp sink current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Pins 1, 9, 12, 15 sink current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to 150°C
Lead temperature (solder 10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
† Pin Nos. refer to 16 Pin DIL Package.
‡ Currents are positive into, negative out of the specified terminal. Consult packaging section of databook for thermal limitations and considerations
of package.
2
www.ti.com
SLUS165C – MARCH 1999 - REVISED JANUARY 2002
electrical characteristics, these specifications apply for TA = –55°C to 125°C for UC1907, –40°C to
85°C for UC2907, and 0°C to 70°C for UC3907, VIN = 15 V, TA = TJ (unless otherwise stated )
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
1.975
2.000
2.025
V
1.960
2.000
2.040
Voltage Amp Section
COMP = 1 V,
Inp t voltage
Input
oltage
Line regulation
Load regulation
Long term stability
TA = 25°C
over temp
COMP = 1 V,
VIN = 4.5 V to 35 V
IL reference = 0.0 mA to –10 mA
Total output variation
TA = 125°C,
Line, load, temp
1000hrs See Note 2
Input adjust range
ADJ OUT from max high to max low
5
1.960
Input bias current
85
V
15
mV
10
mV
25
mV
2.040
100
115
mV
µA
–1
Open loop gain
COMP = 0.75 V to 1.5 V
Unity gain bandwidth
See Note 2
Output sink current
TA = 25°C
(+) SENSE = 2.2 V,
COMP = 1 V
6
15
mA
Output source current
(+) SENSE = 1.8 V,
COMP = 1 V
400
600
µA
VOUT high
VOUT low
(+) SENSE = 1.8 V,
IL = –400 µΑ
IL = 1 mA
1.85
2
V
(+) SENSE = 2.2 V,
65
dB
700
kHz
0.15
0.40
V
1.970
2.000
2.030
V
1.955
2.000
2.045
–15
–30
–60
mA
200
250
300
mV
5
mV
10
mV
15
mV
60
mV
Reference Section
O tp t voltage
Output
oltage
TA = 25°C
Over operating temp
Short circuit current
VREF = 0.0 V
V
Ground Amp Section
Output voltage
Common mode variation
(–) SENSE from 0.0 V to 2 V
Load regulation
reg lation
IL = 0.0 mA to 20 mA,
IL = 0.0 mA to 20 mA,
TA = 25°C
over temp
Adjust Amp Section
Input offset voltage
ADJ OUT = 1.5 V, VCM = 0.0 V
Input bias current
40
50
µA
–2
Open loop gain
1.5 V ≤ ADJ OUT ≤ 2.25 V
Unity gain bandwidth
TA = 25°C,
COUT =1 µF
See Note 2
IOUT = –10 µA to 10 µA,
VOUT = 1.5 V
1.7
3
4.5
ms
VID = 0.0 V,
VID = 250 mV,
ADJ OUT = 1.5 V
55
135
225
µA
Output source current
ADJ OUT = 1.5 V
110
200
350
µA
VOUT high
VOUT low
VID = 250 mV,
VID = 0.0 V,
IOUT = – 50 mA
IOUT = 50 mA
2.20
2.70
2.90
V
0.75
1.15
Common mode rejection ratio
VCM = 0.0 to 10 V
VOUT ADJ OUT = 1.5 V to 2 V,
∆(+) SENSE/ ∆ADJ OUT
Transconductance
Output sink current
Output gain to V/A
65
dB
500
Hz
70
50
V
dB
57
64
mV/V
NOTE 1: Unless otherwise specified all voltages are with respect to (–) SENSE. Currents are positive into, negative out of the specified terminal.
NOTE 2: Ensured by design. Not production tested.
www.ti.com
3
SLUS165C – MARCH 1999 - REVISED JANUARY 2002
electrical characteristics, these specifications apply for TA = –55°C to 125°C for UC1907, –40°C to
85°C for UC2907, and 0°C to 70°C for UC3907, VIN = 15 V, TA = TJ (unless otherwise stated )
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
19.2
19.6
20.1
V/V
210
250
290
mV
180
250
330
mV
600
µV/V
450
mV
Current Amp Section
Gain
O tp t voltage
Output
oltage
Input offset change with common mode
input
VCM = 0.0 V,
VC/S (+) = VC/S (–) = 0.0 V,
VC/S (+) = VC/S (–) = 0.0 V,
VCM = 0 V to 13 V
VOUT high
VOUT low
VID = 1 V
VID = – 1 V,
Power supply rejection ratio
VIN = 4.5 V to 35 V,
VID = 50 mV to 100 mV
TA = 25°C
over temp
10
IL = 1 mA
VCM = 0.0 V
14.5
350
V
60
Slew rate
dB
0.4
V/µs
Drive Amp Section RSET = 500 Ω to Artificial GND, Opto Drive = 15 V
Voltage gain
COMP = 0.5 V to 1 V
2.3
2.5
2.6
ISET VOUT high
ISET VOUT low
(+) SENSE = 2.2 V
3.8
4.1
4.4
V
270
300
mV
35
V
1.55
1.65
1.75
V
5
mV
5
10
20
kΩ
6
15
(+) SENSE = 1.8 V
Opto out voltage range
4
Zero current input threshold
V/V
Buffer Amp Section
Input offset voltage
Input = 1 V
Output off impedance
Input = 1 V,
output = 1.5 V to 2 V
Output source current
Input = 1 V,
output = 0.5 V
Common mode rejection ratio
VCM = 0.3 V to 10 V
VIN = 4.5 V to 35 V
Power supply rejection ratio
mA
70
dB
70
dB
Under Voltage Lockout Section
Startup threshold
3.7
Threshold hysteresis
200
4.4
V
mV
Status Indicate Section
VOUT low
Output leakage
ADJ OUT = current share bus
ADJ OUT = 1 V,
VOUT = 35 V
0.2
0.5
V
0.1
5
µA
3
5
mA
6
10
mA
Total Stand by Current Section
Startup current
Operating current
VIN = UVLO – 0.2 V
VIN = 35 V
NOTE 1: Unless otherwise specified all voltages are with respect to (–) SENSE. Currents are positive into, negative out of the specified terminal.
NOTE 2: Ensured by design. Not production tested.
4
www.ti.com
SLUS165C – MARCH 1999 - REVISED JANUARY 2002
pin assignments
(–) SENSE: (Pin 4) This is a high-impedance pin allowing remote sensing of the system ground, bypassing any
voltage drops which might appear in the power return line. This point should be considered as the true ground. Unless
otherwise stated, all voltages are with respect to this point.
Artificial Ground: (Pin 6) This is a low-impedance-circuit ground which is exactly 250 mV above the (–) SENSE
terminal. This offset allows the ground buffer amplifier negative headroom to return all the control bias and operating
currents while maintaining a high impedance at the (–) SENSE input.
Power RTN: (Pin 5) This should be the most negative voltage available and can range from zero to 5 V below the
(–) SENSE terminal. It should be connected as close to the power source as possible so that voltage drops across
the return line and current-sensing impedances lie between this terminal and the (–) SENSE point.
VREF: (Pin 7) The internal voltage reference is a band-gap circuit set at 2.0 V with respect to the (–) SENSE input
(1.75 V above the artificial ground), and an accuracy of ±1.5%. This circuit, as well as all the other chip functions, will
work over a supply voltage range of 4.5 V to 35 V allowing operation from unregulated dc, an auxiliary voltage, or
the same output voltage that it is controlling. Under-voltage lockout has been included to insure proper startup by
disabling internal bias currents until the reference rises into regulation.
Voltage Amplifier: (Pins 11, 12) This circuit is the feedback-control-gain stage for the power module’s output-voltage
regulation, and overall-loop compensation will normally be applied around this amplifier. Its output will swing from
slightly above the ground return to an internal clamp of 2.0 V. The reference trimming is performed closed loop, and
measured at pin 11, (+) SENSE. The value is trimmed to 2 V ±1.25%.
Drive Amplifier: (Pins 8, 9, 12) This amplifier is used as an inverting buffer between the voltage amplifier’s output
and the medium used to couple the feedback signal to the power controller. It has a fixed-voltage gain of 2.5 and is
usually configured with a current-setting resistor to ground. This establishes a current-sinking output optimized to
drive optical couplers biased at any voltage from 4.5 V to 35 V, with current levels up to 20 mA. The polarity of this
stage is such that an increasing voltage at the voltage amplifier’s sense input (as, for example, at turnon) will increase
the opto’s current. In a nonisolated application, a voltage signal ranging from 0.25 V to 4.1 V may be taken from the
current-setting output but it should be noted that this voltage will also increase with increasing sense voltage and an
external inverter may be required to obtain the correct feedback polarity.
Current Amplifier: (Pins 1, 2, 3) This amplifier has differential-sensing capability for use with an external shunt in
the power-return line. The common mode range of its input will accommodate the full range between the power return
point and VCC-2 V which will allow undefined-line impedances on either side of the current shunt. The gain is
internally set at 20, giving the user the ability to establish the maximum-voltage drop across the current-sense resistor
at any value between 50 mV and 500 mV. While the bandwidth of this amplifier may be reduced with the addition of
an external-output capacitor to ground, in most cases this is not required as the compensation of the adjust amplifier
will typically form the dominant pole in the adjust loop.
Buffer Amplifier: (Pins 1, 15) This amplifier is a unidirectional buffer which drives the current-share bus. The line
which will interconnect all power modules paralleled for current sharing. Since the buffer amplifier will only source
current, it insures that the module with the highest-output current will be the master and drive the bus with a
low-impedance drive capability. All other buffer amplifiers will be inactive with each exhibiting a 10-kΩ load impedance
to ground. The share bus terminal is protected against both shorts to ground and accidental voltages in excess of
50 V.
www.ti.com
5
SLUS165C – MARCH 1999 - REVISED JANUARY 2002
pin assignments
Adjust Amplifier: (Pins 13, 14, 15) This amplifier adjusts the individual module’s reference voltage to maintain
equal-current sharing. It is a transconductance type in order that its bandwidth may be limited and noise kept out of
the reference-adjust circuitry, with a simple capacitor to ground. The function of this amplifier is to compare its own
module-output current to the share-bus signal, which represents the highest output current. This will force an adjust
command which is capable of increasing the reference voltage as seen by the voltage amplifier by as much as 100
mV. This number stems from the 17.5:1 internal resistor ratio between the adjust amplifier’s clamped output and the
reference, and represents a 5% total range of adjustment. This value should be adequate to compensate for
unit-to-unit reference and external-resistor tolerances. The adjust amplifier has a built-in 50-mV offset on its inverting
input which will force the unit acting as the master to have a low output, resulting in no change to the reference. While
this 50-mV offset represents an error in current sharing, the gain of the current amplifier reduces it to only 2.5 mV
across the current-sense resistor. It should also be noted that when the module is acting independently with no
connection to the share bus node, or when the share bus node is shorted to ground, its reference voltage will be
unchanged. Since only the circuit acting as a master will have a low output from the adjust amplifier, this signal is used
to activate a flag output to identify the master, should some corrective action be needed.
Status Indicate: (Pin 16) This pin is an open-collector output intended to indicate the unit which is acting as the
master. It achieves this by sensing when the adjust amp is in its low state and pulling the status-indicate pin low.
additional information
Please refer to additional application information.
1. By Mark Jordan, UC3907 Load Share IC Simplifies Parallel Power Supply Design, TI Literature Number
SLUA147.
2. By Laszlo Balogh, UC3902 Load Share Controller and its Performance in Distributed Power Systems, TI
Literature Number SLUA128.
UDG-94103
Figure 1. Load System Diagram
6
www.ti.com
SLUS165C – MARCH 1999 - REVISED JANUARY 2002
additional information (continued)
V CC
0–20 mA
ISOLATED
CONTROL
UC3907
12
+
1.0 V
VOLTAGE ERROR
AMPLIFIER
(+) SENSE
11
V REFRANGE 2.0 V–2.1 V
–
20 k Ω
–
DRIVE
AMPLIFIER
+
9
ISET
50 k Ω
0–4 V
DIRECT
CONTROL
8
+
REF
MASTER
INDICATE
1.75 V
7
V CC
16
V CC
1.750 V
REF
10
+
0.250 V
ADJUST AMPLIFIER
+
GND
AMPLIFIER
–
50 mV
+
–
( ) SENSE
4
+
20X
–
+
BUFFER
AMPLIFIER
–
+
CURRENT
SHARE
BUS
15
10 k Ω
ARTIFICIAL GND
6
2
FROM LOAD
3
14
CURRENT
SENSE
+
1
ADJ
COMP
13
C/S OUT
5
ADJ IN
PWR RET
TO PWR
RETURN
MODULE LOAD CURRENT
UDG-99053
Figure 2. Load System Connection Diagram
UDG-94105
Figure 3. UC3907 In a Load-Sharing Feedback Loop for an Off-Line Isolated Supply
www.ti.com
7
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
UC1907J
OBSOLETE
CDIP
J
16
TBD
Call TI
Call TI
UC1907J883B
OBSOLETE
CDIP
J
16
TBD
Call TI
Call TI
UC1907L
OBSOLETE
LCCC
FK
20
TBD
Call TI
Call TI
UC1907L883B
OBSOLETE
LCCC
FK
20
TBD
Call TI
Call TI
UC2907DW
ACTIVE
SOIC
DW
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC2907DWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC2907DWTR
ACTIVE
SOIC
DW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC2907DWTRG4
ACTIVE
SOIC
DW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC2907J
OBSOLETE
CDIP
J
16
TBD
Call TI
UC2907N
ACTIVE
PDIP
N
16
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Call TI
N / A for Pkg Type
UC2907NG4
ACTIVE
PDIP
N
16
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UC3907DW
ACTIVE
SOIC
DW
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3907DWG4
ACTIVE
SOIC
DW
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3907DWTR
ACTIVE
SOIC
DW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3907DWTRG4
ACTIVE
SOIC
DW
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UC3907J
OBSOLETE
CDIP
J
16
UC3907N
ACTIVE
PDIP
N
16
UC3907NG4
ACTIVE
PDIP
N
16
TBD
Call TI
Call TI
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Jul-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
UC2907DWTR
SOIC
DW
16
2000
330.0
16.4
10.85
10.8
2.7
12.0
16.0
Q1
UC3907DWTR
SOIC
DW
16
2000
330.0
16.4
10.85
10.8
2.7
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Jul-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UC2907DWTR
SOIC
DW
16
2000
346.0
346.0
33.0
UC3907DWTR
SOIC
DW
16
2000
346.0
346.0
33.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated