application INFO available UC1708 UC2708 UC3708 Dual Non-Inverting Power Driver FEATURES • 3.0A Peak Current Totem Pole Output • 5 to 35V Operation • 25ns Rise and Fall Times • 25ns Propagation Delays • Thermal Shutdown and UnderVoltage Protection • • • DESCRIPTION The UC1708 family of power drivers is made with a high-speed, high-voltage, Schottky process to interface control functions and high-power switching devices – particularly power MOSFETs. Operating over a 5 to 35 volt supply range, these devices contain two independent channels. The A and B inputs are compatible with TTL and CMOS logic families, but can withstand input voltages as high as VIN. Each output can source or sink up to 3A as long as power dissipation limits are not exceeded. Although each output can be activated independently with its own inputs, they can be forced low in common through the action of either a digital high signal at the Shutdown terminal or by forcing the Enable terminal low. The High-Speed, Power MOSFET Compatible Shutdown terminal will only force the outputs low, it will not effect the behavior of the rest of the device. The Enable terminal effectively places the device Efficient High Frequency Operation in under-voltage lockout, reducing power consumption by as much as 90%. During under-voltage and disable (Enable terminal forced low) conditions, Low Cross-Conduction Current Spike the outputs are held in a self-biasing, low-voltage, state. • Enable and Shutdown Functions • Wide Input Voltage Range • ESD Protection to 2kV The UC3708 and UC2708 are available in plastic 8-pin MINI DIP and 16-pin “bat-wing” DIP packages for commercial operation over a 0oC to +70oC temperature range and industrial temperature range of -25oC to +85oC respectively. For operation over a -55oC to +125oC temperature range, the UC1708 is available in hermetically sealed 8-pin MINI CDIP, 16 pin CDIP and 20 pin CLCC packages. Surface mount devices are also available. BLOCK DIAGRAM UDG-92024-1 Note: Shutdown feature available only in JE , NE or DW packages. SLUS171A - MARCH 1997 - REVISED AUGUST 2001 UC1708 UC2708 UC3708 ABSOLUTE MAXIMUM RATINGS (Note 1) Supply Voltage VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35V Output Current (Each Output, Source or Sink) Steady-State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5A Peak Transient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A Ouput Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VIN + 0.3)V Enable and Shutdown Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 6.2V A and B Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VIN + 0.3)V Operating Junction Temperature (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65° to 150°C Lead Temperature (Soldering, 10 Seconds). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C NOTE 1: All voltages are with respect to Logic Gnd pin. All currents are positive into, negative out of, device terminals. NOTE 2: Consult Unitrode Integrated Circuits databook for information regarding thermal specifications and limitations of packages. 3 2 1 ENABLE 4 20 19 18 VIN LOGIC GND 5 17 N/C N/C 6 16 N/C N/C 7 15 N/C SHUTDOWN 8 2 OUTPUT B PWR GND B N/C 14 10 11 12 13 N/C 9 INPUT B Note: In JE package Pin 4 is logic ground. Pins 5, 12, and 13 are N/C. OUTPUT A CLCC-20 (Top View) L Package N/C DIL-16 (Top View) JE or NE Package N/C SOIC-16 (Top View) DW Package INPUT A DIL-8 (Top View) J Or N Package PWR GND A CONNECTION DIAGRAMS VIN UC1708 UC2708 UC3708 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, VIN=10V to 35V, and these specifications apply for: –55oC<TA<125oC for the UC1708, –25oC<TA<+85oC for the UC2708, and 0oC<TA<70oC for the UC3708.TA = TJ. PARAMETER VIN Supply Current TEST CONDITIONS MIN TYP MAX UNITS OutputsLow 18 26 mA Outputs High 14 18 mA Enable = 0V 1 4 mA 0.8 V A, B and Shutdown Inputs Low Level A, B and Shutdown Inputs High Level 2.0 A, B Input Current Low VA,B = 0.4V -1 A, B Input Current High VA,B = 2.4V -200 V -0.6 mA 50 µA A, B Input Leakage Current High VA,B = 35.3V 200 µA Shutdown Input Current Low VSHUTDOWN = 0.4V 20 100 µA Shutdown Input Current High VSHUTDOWN = 2.4V 170 500 µA 0.6 1.5 mA -460 200 µA 200 µA VSHUTDOWN = 6.2V Enable Input Current Low VENABLE = 0V Enable Input Current High VENABLE = 6.2V -600 Enable Threshold Rising 2.8 3.6 V 2.4 3.4 V IOUT = -50mA 2.0 V IOUT = -500mA 2.5 V IOUT = 50mA 0.5 V Enable Threshold Falling Output High Sat., VIN - VOUT Output Low Sat., VOUT 1.0 IOUT = 500mA 2.5 Thermal Shutdown V °C 155 SWITCHING CHARACTERISTICS (Figure 1), (VIN = 20V, delays measured to 10% output change.) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS From A,B Input to Output: Rise Time Delay (TPLH) 10% to 90% Rise (TTLH) Fall Time Delay (TPHL) 90% to 10% Fall (TTHL) CL = 0pF 25 40 ns CL = 1000pF (Note 3) 25 40 ns CL = 2200pF 30 45 ns CL = 0pF 55 75 ns CL = 1000pF (Note 3) 25 50 ns CL = 2200pF 40 55 ns CL = 0pF 25 40 ns CL = 1000pF (Note 3) 25 45 ns CL = 2200pF 35 50 ns CL = 0pF 15 20 ns CL = 1000pF (Note 3) 25 45 ns CL = 2200pF 40 55 ns NOTE 3: These parameters, specified at 1000pF, although ensured over recommended operating conditions, are not tested in production. 3 UC1708 UC2708 UC3708 SWITCHING CHARACTERISTICS (Figure 1), (VIN = 20V, delays measured to 10% output change.) From Shutdown Input to Output Rise Time Delay (TPLH) 10% to 90% Rise (TTLH) Fall Time Delay (TPHL) 90% to 10% Fall (TTHL) Total Supply Current CL = 0pF 25 75 ns CL = 1000pF (Note 3) 30 75 ns CL = 2200pF 35 75 ns CL = 0pf 50 75 ns CL = 1000pF (Note 3) 25 50 ns CL = 2200pF 40 55 ns CL = 0pF 25 45 ns CL = 1000pF (Note 3) 30 50 ns CL = 2200pF 35 55 ns CL = 0pF 25 20 ns CL = 1000pF (Note 3) 25 45 ns CL = 2200pF 40 55 ns F = 200kHz, 50% duty cycle, both channels; CL = 0pF 23 25 mA F = 200kHz, 50% duty cycle, both channels; CL = 2200pF 38 45 mA NOTE 3: These parameters, specified at 1000pF, although ensured over recommended operating conditions, are not tested in production. Figure 1: AC Test Circuit and Switching Time Waveforms 4.3V INPUT 0V 50% 50% 20V 90% 90% OUTPUT 0V 10% 10% TPHL TPLH TTLH TTHL UDG-92026 Figure 2: Equivalent Input Circuits UDG-92025 Note: Shutdown feature available only in JE, NE or DW Packages. 4 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, license, warranty or endorsement thereof. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation or reproduction of this information with alteration voids all warranties provided for an associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Resale of TI’s products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2001, Texas Instruments Incorporated