ALUMINUM ELECTROLYTIC CAPACITORS CW Chip Type, Low Impedance, Long Life Assurance series Chip type with load life of 7000 hours at +105°C. Low impedance temperature range up to +105°C. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). CW CB Low Impedance Specifications Item Performance Characteristics Category Temperature Range – 25 ~ +105°C Rated Voltage Range 6.3 ~ 50V Rated Capacitance Range 10 ~ 470µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C tan δ Rated voltage (V) tan δ (MAX.) 6.3 0.32 10 0.28 16 0.26 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) 6.3 10 16 25 35 50 4 3 2 2 2 2 Z– 25°C / Z+20°C After 7000 hours' application of rated voltage at 105°C , capacitors meet the characteristic requirements listed at right. Endurance Capacitance change tan δ Leakage current Within ±30% of initial value 300% or less of initial specified value Initial specified value or less After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Shelf Life Resistance to soldering heat Black print on the case top. Marking Type numbering system (Example : 10V 150µF) Chip Type (φ5 ~ 6.3 ) E B ± 0.2 φD ± 0.5 A2 150C CW L ± 0.3 Capacitance Lot No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 U CW 1 A 1 5 1 MC L 1 G S A ± 0.2 A ± 0.2 C ± 0.2 0.3MAX. Series 0.5MAX. Positive Plastic platform Voltage ( C : 16V ) Capacitance tolerance (±20%) Rated Capacitance (150µF) Rated voltage (10V) Series name Type Negative H (φ8 ~ 10 ) Voltage V 6.3 Code j Capacitance 10 A 16 C Negative Pressure relief vent 25 E 35 V A ± 0.2 A ± 0.2 L ± 0.5 Lot No. f E B ± 0.2 φD ± 0.5 A2 220V CW C ± 0.2 0.3MAX. Series Trade mark 0.5MAX. Positive Plastic platform Voltage ( V : 35V ) H D´L A B C E L H Taping code Configuration fD Code 5 ¥ 6.3 CL 8 ¥ 10 NL (mm) 5 ´ 7 6.3 ´ 7 6.3 ´ 8.7 8 ´ 10 10 ´ 10 3.2 2.9 2.4 2.4 2.1 10.3 8.3 6.6 6.6 5.3 10.3 8.3 6.6 6.6 5.3 4.5 3.1 2.2 2.2 1.3 10 10 8.7 7.0 7.0 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 50 H Dimension table in next page. CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS CW series Dimensions Cap. (µF) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 10 100 22 220 33 330 5×7 5×7 2.2 2.2 95 95 5×7 2.2 5×7 2.2 95 5×7 2.2 95 6.3 × 7 1.1 140 6.3 × 8.7 1.0 230 6.3 × 8.7 1.0 230 95 47 470 5×7 2.2 95 6.3 × 7 1.1 140 6.3 × 7 1.1 140 100 101 6.3 × 7 1.1 140 6.3 × 7 1.1 140 6.3 × 8.7 1.0 230 150 151 6.3 × 8.7 1.0 230 220 221 6.3 × 8.7 1.0 230 6.3 × 8.7 1.0 230 8 × 10 0.22 600 8 × 10 0.22 600 330 331 6.3 × 8.7 1.0 230 8 × 10 0.22 600 8 × 10 0.22 600 10 × 10 0.16 850 470 471 8 × 10 0.22 600 8 × 10 0.22 600 10 × 10 0.16 850 6.3 × 7 1.1 140 8 × 10 0.53 350 8 × 10 0.53 350 10 × 10 0.35 670 Impedance Rated ripple Case size φ D × L (mm) Max. impedance (Ω) at 20°C 100kHz, Rated Ripple (mArms) at 105°C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz~ 1.00 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V