ALUMINUM ELECTROLYTIC CAPACITORS UB Chip Type, High Reliability series WH Chip type, high temperature range, for +125°C use. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). High Temperature Reflow Added ESR specification at – 40°C CJ High Temperature UB UX Specifications Item Performance Characteristics Category Temperature Range – 40 ~ +125°C Rated Voltage Range 10 ~ 50V Rated Capacitance Range 10 ~ 330µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C tan δ 10 0.32 Rated voltage (V) tan δ (MAX.) 16 0.24 25 0.21 35 0.18 50 0.18 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C 16 25 35 50 12 8 6 4 4 After 2000 hours' (φ8 × 6.2 : 1000 hours) application of rated voltage at 125°C, capacitors meet the characteristic requirements listed at right. Endurance Capacitance change tan δ Leakage current Within ±30% of initial value 300% or less of intial specified value Initial specified value or less After storing the capacitors under no load at 125°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Shelf Life Resistance to soldering heat Black print on the case top. Chip Type A±0.2 A±0.2 0.5MAX. E L±0.5 Pressure relief vent A B C E L H Negative H (mm) D L 8 ´ 6.2 f ´ Configuration D L Code 8 6.2 CL 8 10 NL 10 10 NL Capacitance tolerance (±20%) Rated Capacitance (100mF) Rated voltage (10V) Series name Type Positive C±0.2 B±0.2 D±0.5 Plastic platform 0.3MAX. Taping code Negative H f A2E 330 10V 125¡C Marking Capacitance Lot No. Voltage Trade mark 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UUB 1 A 1 0 1 MCL 1GS 0.5MAX. E B±0.2 D±0.5 C±0.2 L±0.3 (φ8 × 10, φ10 × 10) Type numbering system (Example : 10V 100µF) Positive Plastic platform 0.3MAX. Voltage A2E 100 10V 125¡C Marking Capacitance Lot No. f (φ8 × 6.2) A±0.2 A±0.2 Marking Trade mark 10 f ´ ´ ´ ´ 8 ´ 10 10 ´ 10 3.3 2.9 3.2 8.3 8.3 10.3 8.3 8.3 10.3 2.3 3.1 4.5 6.2 10 10 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 Dimensions Cap.(µF) 10 22 33 47 100 220 330 10 1A V Code 100 220 330 470 101 221 331 8 × 6.2 8 × 10 10 × 10 16 1C 58 90 112 8 × 10 10 × 10 25 1E 66 102 8 × 6.2 8 × 10 10 × 10 35 1V 48 74 116 8 × 6.2 8 × 10 10 × 10 50 1H 44 52 80 8 × 6.2 8 × 6.2 8 × 10 10 × 10 Case size φ D × L (mm) 24 38 46 58 Rated ripple Rated Ripple (mArms) at 125°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UH(p.78) series if high CV products are required. Please refer to page 3 for the minimum order quantity. CAT.8100V