ALUMINUM ELECTROLYTIC CAPACITORS UH Chip Type, High Reliability, Higher Capacitance Range series Chip Type, higher capacitance in larger case sizes (φ12.5, φ16, φ18, φ20) Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape and tray. Adapted to the RoHS directive (2002/95/EC). UH High Temperature UJ Specifications Performance Characteristics Item Category Temperature Range – 55 ~ +125°C Rated Voltage Range 10 ~ 50V Rated Capacitance Range 100 ~ 3300µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 1 minutes' application of rated voltage, leakage current is not more than 0.03CV or 4 (µA), whichever is greater. tan δ Rated voltage (V) 10 16 25 35 50 tan δ (MAX) 0.22 0.18 0.16 0.14 0.12 120Hz 20°C For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF. Rated voltage (V) 10 16 25 35 50 Stability at Low Temperature Impedance ratio Z–25°C / Z+20°C 4 3 2 2 2 ZT / Z20 (MAX.) Z–40°C / Z+20°C 8 6 4 3 3 120Hz Endurance After 5000 hours' application of rated voltage at 125°C, capacitors meet the characteristic requirements listed at right. Shelf Life After storing the capacitors under no load at 125°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. Marking Black print on the case top. B±0.2 D±0.5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UUH 1 H 3 3 1 M NL 1 MS f E 330 µF UH 50V H0536 nichicon Type numbering system (Example : 50V 330µF) C±0.2 B±0.2 Plastic platform A±0.2 Chip Type Trade mark Voltage Lot No. Within ±30% of initial value 300% or less of initial specified value Initial specified value or less Capacitance change tan δ Leakage current Pressure relief vent D A B C E H f 12.5 4.0 13.6 16.0 8.0 2.5 Size code L±0.5 16. 4.5 17.1 19.5 10.5 3.75 18. 5.0 19.1 21.5 11.5 3.75 H±0.1 (mm) 20. 5.0 21.1 23.5 13.5 3.75 Capacitance Tolerance (± 20%) Rated Capacitance (330µF) Rated voltage (50V) Series name Type A±0.2 Series Capacitance The lead terminal structure : The same bent lead type (refer to p.60) that is currently used on 10mm diameter and smaller parts, is also available upon request. In this case of the bent lead type, Q will be put at the 11th digit of type numbering system. Please ask for details. Package code Taping MS Tray ZD Configuration Code fD 12.5~18 NL RL 20 Dimensions V (µF) 10 1A Code Cap. 100 101 220 221 330 331 470 471 12.5 × 13.5 1000 102 2200 222 3300 332 16 1C 25 1E 0100 ~ 4700 1000 ~ 3300 16 × 16.5 250 16 × 21.5 18 × 16.5 18 × 21.5 340 340 430 12.5 × 13.5 230 16 × 16.5 280 230 12.5 × 13.5 250 16 × 16.5 310 12.5 × 16.5 350 16 × 16.5 440 620 620 770 18 × 21.5 540 540 380 380 610 18 × 16.5 16 × 21.5 18 × 21.5 18 × 21.5 20 × 16.5 18 × 16.5 16 × 21.5 20 × 21.5 710 50 Hz 0.80 0.85 120 Hz 1.00 1.00 170 200 210 Case size φ D × L (mm) 300 Hz 1.23 1.10 1 kHz 1.34 1.13 Rated Ripple Rated Ripple (mArms) at 125°C 120Hz Frequency coefficient of rated ripple current Frequency 50 1H 12.5 × 13.5 12.5 × 13.5 12.5 × 13.5 In this case, 6 will be put at 12th digit of type numbering system, " " Cap.(µF) 35 1V 10 kHz~ 1.50 1.15 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V