STMICROELECTRONICS Z0103MN6AA4

Z01
Standard 1A Triacs
Features
A2
■
On-state rms current, IT(RMS) 1 A
■
Repetitive peak off-state voltage, VDRM/VRRM
600 or 800 V
■
G
A1
A2
Triggering gate current, IGT (Q1) 3 to 25 mA
Description
G
The Z01 series is suitable for general purpose AC
switching applications. These devices are
typically used in applications such as home
appliances (electrovalve, pump, door lock, small
lamp control), fan speed controllers,...
A2
G
A1
A2
A1
SOT-223
Z01xxN
TO-92
Z01xxA
Different gate current sensitivities are available,
allowing optimized performance when driven
directly through microcontrollers.
A2
A1
G
SMBflat-3L
Z01xxMUF
December 2010
Doc ID 7474 Rev 10
1/12
www.st.com
12
Characteristics
1
Z01
Characteristics
Table 1.
Absolute maximum ratings
Symbol
IT(RMS)
ITSM
I ²t
Parameter
SOT-223
Ttab = 90 °C
TO-92
TL = 50 °C
SMBflat-3L
Ttab = 107 °C
Non repetitive surge peak on-state
current (full cycle, Tj initial = 25 °C)
F = 50 Hz
t = 20 ms
F = 60 Hz
t = 16.7 ms
I²t Value for fusing
tp = 10 ms
On-state rms current
(full sine wave)
Value
Unit
1
A
8
A
8.5
0.35
A²s
dI/dt
Critical rate of rise of on-state current
F = 120 Hz
IG = 2 x IGT , tr ≤ 100 ns
Tj = 125 °C
20
A/µs
IGM
Peak gate current
Tj = 125 °C
1
A
Tj = 125 °C
1
W
- 40 to + 150
- 40 to + 125
°C
PG(AV)
Tstg
Tj
Table 2.
tp = 20 µs
Average gate power dissipation
Storage junction temperature range
Operating junction temperature range
Electrical characteristics (Tj = 25 °C, unless otherwise specified)
Z01
Symbol
IGT (1)
Test conditions
Quadrant
Unit
I - II - III
VD = 12 V,
RL = 30 Ω
VGT
VGD
VD = VDRM,
RL = 3.3 kΩ,
Tj = 125 °C
IH (2)
IT = 50 mA
IL
IG = 1.2 IGT
IV
09
10
3
5
10
25
5
7
10
25
mA
ALL
MAX.
1.3
V
ALL
MIN.
0.2
V
MAX.
7
10
10
25
7
10
15
25
15
20
25
50
MIN.
10
20
50
100
V/µs
MIN.
0.5
1
2
5
V/µs
MAX.
II
VD = 67% VDRM gate open
Tj = 110 °C
(dV/dt)c (dI/dt)c = 0.44 A/ms,
(2)
Tj = 110 °C
1. Minimum IGT is guaranteed at 5% of IGT max.
2. For both polarities of A2 referenced to A1.
2/12
07
MAX.
I - III - IV
dV/dt (2)
03
Doc ID 7474 Rev 10
mA
mA
Z01
Characteristics
Table 3.
Static characteristics
Symbol
VTM(1)
Test conditions
Value
Unit
ITM = 1.4 A, tp = 380 µs
Tj = 25 °C
MAX.
1.6
V
Vto
(1)
Threshold voltage
Tj = 125 °C
MAX.
0.95
V
Rd
(1)
Dynamic resistance
Tj = 125 °C
MAX.
400
mΩ
5
µA
0.5
mA
Value
Unit
IDRM
IRRM
Tj = 25 °C
VDRM = VRRM
MAX.
Tj = 125 °C
1. For both polarities of A2 referenced to A1.
Table 4.
Thermal resistances
Symbol
Parameter
Rth(j-t)
Junction to tab (AC)
SOT-223
25
Rth(j-t)
Junction to tab (AC)
SMBflat-3L
14
Rth(j-I)
Junction to lead (AC)
TO-92
60
MAX.
S(1)
Rth(j-a)
=5
cm²
Junction to ambient
°C/W
SOT-223
60
SMBflat-3L
75
TO-92
150
1. S = copper surface under tab.
Figure 1.
Maximum power dissipation
versus on-state rms current
(full cycle)
Figure 2.
P(W)
On-state rms current versus lead
(TO-92) or tab (SOT-223, SMBflat3L) temperature (full cycle)
IT(RMS)(A)
1.50
1.2
α=180 °
1.25
1.0
1.00
0.8
0.75
0.6
0.50
0.4
SOT-223
TO-92
0.2
180°
0.25
SMBF3L
Tl or Ttab(°C)
IT(RMS)(A)
0.0
0.00
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0
Doc ID 7474 Rev 10
25
50
75
100
125
3/12
Characteristics
Figure 3.
Z01
On-state rms current versus
ambient temperature (free air
convection full cycle)
Figure 4.
IT(RMS)(A)
1.2
Relative variation of thermal
impedance versus pulse duration
(Zth(j-a))
K=[Zth(j-a)/Rth(j-a)]
1.00
Z01xxA
1.0
Rth(j-a) = 60°C/W
(SOT-223)
Z01xxMUF
Copper surface area
= 5cm²
0.8
Rth (j-a) = 100°C/W
(SMBflat-3L)
0.6
0.10
Z01xxN
Rth(j-a) = 150°C/W
(TO-92)
0.4
0.2
tp(s)
Tamb (°C)
0.01
1.0E-03
0.0
0
25
Figure 5.
2.5
50
75
100
1.0E-02
1.0E-01
1.0E+00
1.0E+01
1.0E+02
1.0E+03
125
Relative variation of holding
Figure 6.
current and latching current versus
junction temperature (typ. values)
Relative variation of gate trigger
current (IGT) and voltage (VGT)
versus junction temperature
IGT, VGT[T j] / IGT, VGT[T j=25 °C]
IH, IL [Tj] /IH, IL [Tj=25°C]
3.0
2.5
2.0
IGT Q1-Q2
IGT Q3
2.0
IGT Q4
1.5
1.5
1.0
1.0
IL
0.5
IH
0.5
Tj (°C)
0.0
-50
-25
Figure 7.
0
25
50
75
VGT Q1-Q2-Q3-Q4
100
125
Tj(°C)
0.0
-50
Surge peak on-state current versus Figure 8.
number of cycles
ITSM(A)
9
-25
0
25
50
75
100
125
Non-repetitive surge peak
on-state current and corresponding
value of I2t sinusoidal pulse width
ITSM (A), I2t (A2s)
100.0
8
Tj initial = 25°C
T = 20 ms
7
One cycle
Non repetitive
Tjinitial = 25 °C
6
dI/dt limitation:
20A/µs
ITSM
10.0
5
4
3
1.0
2
I2t
Repetitive
Tamb = 95 °C
1
Number of cycles
0
1
4/12
10
100
1000
0.1
0.01
Doc ID 7474 Rev 10
tp (ms)
0.10
1.00
10.00
Z01
Characteristics
Figure 9.
On-state characteristics
(maximum values) (ITM = f(VTM)
Figure 10. Relative variation of critical rate
of decrease of main current versus
(dV/dt)c
ITM(A)
(dI/dt)c [(dV/dt)c] / Specified (dI/dt)c
10.0
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
Tj = Tjmax.
1.0
Tj=max.
Vt0=0.95 V
Rd=400 mΩ
Tj = 25°C
VTM (V)
0.1
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
Figure 11. Relative variation of critical rate of
decrease of main current (dI/dt)
versus junction temperature
Z0107
Z0110
(dV/dt)c (V/µs)
0.1
5.0
Z0109
Z0103
1.0
10.0
100.0
Figure 12. SOT-223 and SMBflat-3L thermal
resistance junction to ambient
versus copper surface under case
Rth(j-a)(°C/W)
170
(dI/dt)c [Tj] / (dI/dt)c [Tj Specified]
160
6
150
5
140
130
4
120
SMBF3L
110
3
100
2
90
70
Tj (°C)
0
SOT223
80
1
0
25
50
60
75
100
125
SCU(cm²)
50
0
1
2
3
4
5
Figure 13. Relative variation of static dV/dt immunity versus junction temperature (gate open)
6
dV/dt [T j] / dV/dt [T j=125 °C]
VD=VR=402V
5
4
3
2
1
T j(°C)
0
25
50
75
Doc ID 7474 Rev 10
100
125
5/12
Ordering information scheme
2
Z01
Ordering information scheme
Figure 14. Ordering information scheme
Z 01 03 M A [BLANK] 1AA2
Triac series
Current
01 = 1 A
Sensitivity
03 = 3 mA
07 = 5 mA
09 = 10 mA
10 = 25 mA
Voltage
M = 600 V
N = 800 V
Package
A = TO-92
N = SOT-223
UF = SMBF3L
Packing mode
1AA2 = TO-92 bulk
2AL2 = TO-92 ammopack
5AL2 = TO-92 tape and reel
5AA4 = SOT-223 tape and reel 7”
6AA4 = SOT-223 tape and reel 13”
Blank = SMBflat-3L tape and reel 13”
6/12
Doc ID 7474 Rev 10
Z01
Ordering information scheme
Table 5.
Product Selector
Voltage
Order code
600 V
Z0103MA
X
Z0103MN
X
Sensitivity
Type
Package
3 mA
Standard
TO-92
800 V
3 mA
Standard
SOT-223
Z0103NA
X
3 mA
Standard
TO-92
Z0103NN
X
3 mA
Standard
SOT-223
5 mA
Standard
TO-92
Z0107MA
X
Z0107MN
X
5 mA
Standard
SOT-223
Z0107NA
X
5 mA
Standard
TO-92
Z0107NN
X
5 mA
Standard
SOT-223
10 mA
Standard
TO-92
Z0109MA
X
Z0109MN
X
10 mA
Standard
SOT-223
Z0109NA
X
10 mA
Standard
TO-92
Z0109NN
X
10 mA
Standard
SOT-223
25 mA
Standard
TO-92
Z0110MA
X
Z0110MN
X
25 mA
Standard
SOT-223
Z0110NA
X
25 mA
Standard
TO-92
Z0110NN
X
25 mA
Standard
SOT-223
3 mA
Standard
SMBflat-3L
Z0103MUF
X
Z0107MUF
X
5 mA
Standard
SMBflat-3L
Z0109MUF
X
10 mA
Standard
SMBflat-3L
Doc ID 7474 Rev 10
7/12
Packaging information
3
Z01
Packaging information
●
Epoxy meets UL94, V0
●
Lead-free packages
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Table 6.
SOT-223 dimensions
Dimensions
Ref.
V
A
A1
c
B
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
Max.
1.80
0.071
0.02
0.10
0.001 0.004
0.60
0.70
0.85 0.024 0.027 0.033
B1
2.90
3.00
3.15 0.114 0.118 0.124
c
0.24
0.26
0.35 0.009 0.010 0.014
D(1)
6.30
6.50
6.70 0.248 0.256 0.264
e1
A1
D
B
B1
4
H
E
1
2
3
e
e
2.3
0.090
e1
4.6
0.181
(1)
3.30
3.50
3.70 0.130 0.138 0.146
H
6.70
7.00
7.30 0.264 0.276 0.287
E
V
10° max
1. Do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15mm (0.006inches)
Figure 15. SOT-223 footprint dimensions (in millimeters)
3.25
1.32
5.16
7.80
1.32
2.30
8/12
Doc ID 7474 Rev 10
0.95
Z01
Packaging information
Table 7.
TO-92 dimensions
Dimensions
REF.
Millimeters
Min.
Typ.
Max.
Inches
Min.
Typ.
Max.
A
a
B
A
1.35
B
C
4.70
C
D
F
Table 8.
E
0.053
0.185
2.54
0.100
D
4.40
0.173
E
12.70
0.500
F
3.70
0.146
a
0.50
0.019
SMBflat-3L dimensions
Dimensions
Ref.
e
Min.
A
0.90
1.10
0.035
0.043
b
0.35
0.65
0.014
0.026
b4
1.95
2.20
0.07
0.087
c
0.15
0.40
0.006
0.016
D
3.30
3.95
0.130
0.156
E
5.10
5.60
0.201
0.220
E1
4.05
4.60
0.156
0.181
L
0.75
1.50
0.030
0.059
c
b 2x
L2 2x
L 2x
Inches
Min. Typ. Max.
A
D
Millimeters
L1
E E1
Typ.
Max.
L1
L
L2
b4
L1
0.40
0.016
L2
0.60
0.024
e
1.60
0.063
Figure 16. SMBflat-3L footprint dimensions
5.84
(0.230)
0.51
(0.020)
2.07
(0.082)
2.07
(0.082)
0.51
(0.020)
1.20
(0.047)
3.44
(0.136)
1.20
(0.047)
millimeters
(inches)
Doc ID 7474 Rev 10
9/12
Packaging information
Z01
Figure 17. Footprint and connectors for SOT-223 or SMBflat-3L (dimensions in mm)
5.84
3.42
3.25
1.19
1.32
1.50
2.92
SOT-223
Solder resist
1.35
1.20
1.08
Solder lands
SMBF3L
7.80
2.07
2.22
SMBF3L
1.95
SMBF3L
2.07
0.61
0.51
0.46
1.30
1.20
1.08
Solder paste
1.47
1.32
1.19
Connector line
SOT-223
SOT-223
0.85
0.95
1.10
2.30
10/12
Doc ID 7474 Rev 10
SOT-223
Z01
4
Ordering information
Ordering information
Table 9.
Ordering information
Order code(1)
Marking(1)
Package
Weight
Base quantity
Delivery mode
Z01xxyA 1AA2
Z01xxyA
TO-92
0.2 g
2500
Bulk
Z01xxyA 2AL2
Z01xxyA
TO-92
0.2 g
2000
Ammopack
Z01xxyA 5AL2
Z01xxyA
TO-92
0.2 g
2000
Tape and reel
Z0103yN 5AA4
Z3y
SOT-223
0.12 g
1000
Tape and reel
Z0107yN 5AA4
Z7y
SOT-223
0.12 g
1000
Tape and reel
Z0109yN 5AA4
Z9y
SOT-223
0.12 g
1000
Tape and reel
Z0103MUF
Z3M
SMBflat-3L
46.78 mg
5000
Tape and reel
Z0107MUF
Z7M
SMBflat-3L
46.78 mg
5000
Tape and reel
Z0109MUF
Z9M
SMBflat-3L
46.78 mg
5000
Tape and reel
1. xx = sensitivity, y = voltage
5
Revision history
Table 10.
Document revision history
Date
Revision
Changes
Oct-2001
4
Last update.
10-Feb-2005
5
Package: TO-92 tape and reel delivery mode 5AL2 added.
09-May-2005
6
Table 4 on page 2: typo. mistake corrected
1. (dV/dt)c instead of (dI/dt)c
2. V/µs unit instead of A/ms
21-Apr-2006
7
Reformatted to current standard. Table 2 on page 2: Typo
corrected. Values for IGT split into two separate rows.
10-Oct-2006
8
Table 2: modified test conditions for (dV/dt)c. Changed “ambient”
to “lead or tab” in Figure 2.
20-Oct-2010
9
Package: SOT-223 13” tape and reel added = 6AA4
14-Dec-2010
10
Added package SMBflat-3L. Updated dimensions in Table 6.
Updated Figure 3 and Figure 12. Updated Table 5: Product
Selector.
Doc ID 7474 Rev 10
11/12
Z01
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
12/12
Doc ID 7474 Rev 10