ZTB912F Ceramic Resonator 1 SCOPE This specification shall cover the characteristics of the ceramic resonator with the type ZTB912F. 2 PART NO. PART NUMBER CUSTOMER PART NO SPECIFICATION NO ZTB912F 3 OUTLINE DRAWING AND DIMENSIONS 3.1 Appearance: No visible damage and dirt. 3.2 Construction: Leads are soldered on electrode and body is molded by resin. 3.3 Except the chip(ceramic element, ceramic base, capacitance slice), the materials don’t contain lead. 2.2±0.2 0.8max 912F * 6.0±0.3 5.0±0.3 3.4 Dimensions 4.0±0.5 0.8±0.02 0.6±0.02 0.2±0.05 0.1±0.03 2.5±0.2 *: EIAJ monthly code http://www.luguang.cn mail:[email protected] ZTB912F Ceramic Resonator 4 ELECTRICAL SPECIFICATIONS 4.1 RATING Items Content Withstanding Voltage (V) 50 (DC，1min) Insulation Resistance Ri,（MΩ）min. 100 （100V，1min） Operating Temperature Range (℃) -20～+80 Storage Temperature Range (℃) -40～+85 4.2 ELECTRICAL SPECIFICATIONS Items Anti-Resonant Frequency （kHz） Frequency Accuracy （%） Resonant Impedance Ro（Ω）max Anti-Resonant Impedance Ro（kΩ）min Static Capacitance（pF） Bandwidth(Fa-Fr),（kHz）min Temperature Coefficient of Anti-Resonant Frequency （%） max Rating Voltage UR（V）max Aging Rate （%）max IC 5 Content 923.0 ±0.3 60 20 180(1±20%) 38 ±0.3（-20℃～+80℃） 6VDC 15Vp-p ±0.3 （For Ten Years） LA1780（SANYO） MEASUREMENT 5.1 Measurement Conditions: Parts shall be measured under a condition ( Temp.： 20±15 ℃ ,Humidity ： 65±20% R.H.) unless the standard condition(Temp. ： 25±3℃,Humidity ：65±5% R.H.) is regulated to measure. 5.2 Test Circuit http://www.luguang.cn mail:[email protected] ZTB912F Ceramic Resonator 6.PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS No 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 Item Humidity High Temperature Exposure Low Temperature Exposure Temperature Cycling Vibration Condition of Test Subject the resonator at +40 ℃ ± 2 ℃ and 90%-95% R.H. for 96h, resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to +85℃±5℃ for 96h, resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to –25℃±5℃ for 96h, resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to －25℃ for 30 min. followed by a high temperature of +85℃ for 30 min. Cycling shall be repeated 5 times. Resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to vibration for 2h each in x y and z axis with the amplitude of 1.5mm, the frequency shall be varied uniformly between the limits of 10Hz-55Hz and then resonator shall be measured. Performance Requirements It shall fulfill the specifications in Table 1. It shall fulfill the specifications in Table 1. It shall fulfill the specifications in Table 1. It shall fulfill the specifications in Table 1. It shall fulfill the specifications in Table 1. No visible damage Resonator shall be measured after 3 times' Mechanical and it shall fulfill random dropping from the height of 70cm on the specifications in Shock concrete floor. Table 1. Lead terminals are immersed up to 2 mm from Resistance to resonator’s body in soldering bath of 260℃± It shall fulfill the in Soldering 5℃ for 10s±1s and then resonator shall be specifications Heat measured after being placed in natural Table 1. conditions for 1h More than 95% of Lead terminals are immersed up to 2mm from the terminal surface Solderability resonator’s body in soldering bath of 250℃± of the resonator shall be covered 5℃ for 3s±0.5s. with fresh solder. (To be continued) http://www.luguang.cn mail:[email protected] ZTB912F Ceramic Resonator 6 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS No. 6.9 Item Terminal Strength 6.9.1 Terminal Pulling 6.9.2 Terminal Bending Performance Requirements Force of 5N is applied to each lead in axial No visible damage direction for 10s±1s. and it shall fulfill When force of 5N is applied to each lead in the specifications axial direction,the lead shall folded up 90° in Table 1. from the axial direction and folded back to the axial direction. The speed of folding shall be each 3s. Condition of Test Table 1 Item Anti-Resonant Frequency Change ΔFa/Fa（%）max Specification after test ±0.3 Note:The limits in the above table are referenced to the initial measurements. http://www.luguang.cn mail:[email protected] ZTB912F Ceramic Resonator 7 PACKAGE To protect the products in storage and transportation，it is necessary to pack them(outer and inner package).On paper pack, the following requirements are requested. 7.1 Section of package Package is made of corrugated paper with thickness of 0.8cm.Package has 2 inner packages, each has 20 inner boxes (each box for plastic bag). 7.2 Quantity of package Per plastic bag 500 pieces Per inner box 3 plastic bags Per inner package 20 inner boxes Per package 2 inner packages (60000 pieces of piezoelectric ceramic part) 7.3 Dimensions and Mark At the end of package, the warning (moisture proof, upward put) should be stick to it(see below) ③ ④ ① ⑤ 300mm ② ⑦ 34 0m m ⑥ 450mm ① Belt(2.9m) ③ Label(1) ⑤ Package(1) ② Certificate of ④ Adhesive ⑥ Box(2) proval(1) tape(1.2m) ⑦ Inner box(40) http://www.luguang.cn mail:[email protected] ZTB912F Ceramic Resonator 7.4 Inner package 0m m ① 135mm 32 ② 435mm ① Label ② Inner package 7.5 Inner box Dimensions ① 82 mm 52mm ② ③ 152mm Pars shall be packaged in box with hold down tape upside. Part No., quantity and lot No. http://www.luguang.cn mail:[email protected] ZTB912F Ceramic Resonator 8 EIAJ Monthly Code 2003 / 2005 / 2007 / 2009 MONTH CODE JAN A FEB B MAR C APR D MAY E JUN F JUL G AUG H SEP J OCT K NOV L DEC M 2004 / 2006 / 2008 / 2010 MONTH CODE JAN N FEB P MAR Q APR R MAY S JUN T JUL U AUG V SEP W OCT X NOV Y DEC Z 9 OTHER 9.1 Caution of use 9.1.1 Do not clean or wash the component for it is not hermetically sealed. 9.1.2 Don’t be close to fire 9.1.3 Don’t apply excess mechanical stress to the component. 9.1.4 Don’t bend terminals of the component 9.1.5 This specification mentions the quality of the component as a single unit. Please insure the component is thoroughly evaluated in your application circuit. 9.1.6 Don’t use reflow-solder。 9.1.7 Expire date (Shelf life) of the products is six months after delivery under the conditions of a sealed and an unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because the products may be degraded in the solderability and/or rusty.Please confirm solderability and characteristics for the products regularly. 9.2 Notice 9.2.1 Please return one of this specification after your signature of acceptance. 9.2.2 When something gets doubtful with this specifications, we shall jointly work to get an agreement. http://www.luguang.cn mail:[email protected]