ZTTCE12.00MG Ceramic Resonator 1．SCOPE This specification shall cover the characteristics of the ceramic resonator with the type ZTTCE12.00MG50HD0F-R0. 2．PART NO. PART NUMBER PREVIOUS PART NUMBER ZTTCE12.00MG50HD0F-R0 ZTTCE12.00MG CUSTOMER PART NO SPECIFICATION NO 3．OUTLINE DIMENSIONS AND MARK 3.1 Appearance: No visible damage and dirt. 3.2 Construction: SMD ceramic packaging. 3.3 The products conform to the RoHS directive and national environment protection law. 3.4 Dimensions and mark 1.3±0.1 3.2±0.1 ② ③ 0.4±0.1 0.4±0.1 0.4±0.1 1.0max ① ① Input ② Ground ③ Output 1.2±0.1 1.2±0.1 http://www.luguang.cn 0.4±0.1 mail:[email protected] ZTTCE12.00MG Ceramic Resonator 3.5 STRUCTURE 3 4 1 5 2 NO. Components Materials Top and Bottom Electrodes 1 Ag+Ni(under plating)+Sn(over plating) Outer Electrodes Side Electrodes Ni+Cu+Ag(under plating)+Sn(over plating) 2 Ceramic Box Insulation Box 3 Cover Dielectric Material 4 Inner Electrodes Ag 5 Glue Epoxy Resin 6 Conductive Adhesive Ag+Epoxy Resin 7 Ceramic Element Piezoelectric Ceramics (PZT) 4．ELECTRICAL SPECIFICATIONS 4.1 RATING Items Requirement Withstanding Voltage (V) 50 (DC，1min) Insulation Resistance Ri,（MΩ）min. 100 （10V，1min） Operating temperature -25℃～＋85℃ Storage temperature -55℃～＋85℃ Rating Voltage UR（V） http://www.luguang.cn 6V DC 15V p-p mail:[email protected] ZTTCE12.00MG Ceramic Resonator 4.2 ELECTRICAL SPECIFICATIONS Items Requirement Oscillation Frequency Fosc (MHz) 12.000 Frequency Accuracy (%) ±0.5 Resonant Impedance Ro (Ω)max. 40 Temperature Coefficient of Oscillation Frequency (%) max. ±0.3 (Oscillation Frequency drift， -25℃～+85℃) Aging Rate （%）max. * ±0.2 （From initial value） *Components shall be left in a chamber of +85±2℃ for 1000 hours, then measured after leaving in natural condition for 1 hours. 5．TEST 5.1 Test Conditions Parts shall be tested under the condition ( Temp.：20±15℃,Humidity ：65±20% R.H.) unless the standard condition(Temp.：25±3℃,Humidity ：65±10% R.H.) is regulated to measure. 5.2 Test Circuit VDD:+5V IC IC Output 1MΩ C1 C2 http://www.luguang.cn X IC: 1/6TC4069UBP×2 X: Ceramic esonator mail:[email protected] ZTTCE12.00MG Ceramic Resonator 6 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS No Condition of Test Item 6.1 Humidity Keep the resonator at 40℃±2℃ and 90%-95% RH for 96h. Then Release the resonator into the room Condition for 1h prior to the Measurement. 6.2 High Temperature Exposure Subject the resonator to 85±2℃ for 96h, then release the resonator into the room conditions for 1h prior to the measurement. 6.3 Low Temperature Exposure Subject the resonator to -55±2℃ for 96h, then release the resonator into the room conditions for 1h prior to the measurement. 6.4 Temperature Cycling 6.5 Vibration 6.6 Mechanical Shock After temperature cycling of blow table was performed 5 times, resonator shall be measured after being placed in natural conditions for 1h. Temperature Time –25±3℃ 30±3 min 85±3℃ 30±3 min Subject the resonator to vibration for 2h each in x、y and z axis With the amplitude of 1.5mm, the frequency shall be varied uniformly between the limits of 10 Hz—55Hz. Soldering Test It shall fulfill the specifications in Table 1. It shall fulfill the specifications in Table 1. It shall fulfill Drop the resonator randomly onto a wooden the floor from the height of 100cm 3 times. specifications in Table 1. Passed through the re-flow oven under the following condition and left at room temperature for 1h before measurement. Peak:260℃max 6.7 Performance Requirements It shall fulfill the specifications in Table 1. It shall fulfill the specifications in Table 1. It shall fulfill the specifications in Table 1. 10s max 250℃ 230℃ 150℃ It shall fulfill the specifications in Table 1. Pre-heating 100℃ 30s min within 80-120s. within 20-40s （To be continued） http://www.luguang.cn mail:[email protected] ZTTCE12.00MG Ceramic Resonator 6 PHYSICAL AND ENVIRONMENAL CHARACTERISICS No 6.8 Item Solder Ability Performance Requirements Dipped in 245℃±5℃ solder bath for The terminals shall 3s±0.5 s with rosin flux (25wt% ethanol be at least 95% solution.) covered by solder. Condition of Test Mount a glass-epoxy board (Width=40mm,thickness=1.6mm),then bend it to 1mm displacement and keep it for 5s. (See the following figure) PRESS 6.9 Board Bending PRESS HEAD Mechanical damage such as breaks shall not occur. SUPPORT BAR Table 1 Item Oscillation Frequency Change △Fosc/Fosc (%) max Resonant Impedance (Ω) max Specification after test ±0.3 40 The limits in the above table are referenced to the initial measurements. http://www.luguang.cn mail:[email protected] ZTTCE12.00MG Ceramic Resonator 7 RECOMMENDED LAND PATTERN AND REFLOW SOLDERING STANDARD CONDITIONS 7.1Recommended land pattern :Land Pattern 7.2Recommended reflow soldering standard conditions Peak:260℃max 10s max 250℃ 230℃ 150℃ Pre-heating 100℃ 30s min within 80-120s. http://www.luguang.cn within 20-40s mail:[email protected] ZTTCE12.00MG Ceramic Resonator 7 RECOMMENDED LAND PATTERN AND REFLOW SOLDERING STANDARD CONDITIONS 7.1Recommended land pattern :Land Pattern 7.2Recommended reflow soldering standard conditions Peak:260℃max 10s max 250℃ 230℃ 150℃ Pre-heating 100℃ 30s min within 80-120s. http://www.luguang.cn within 20-40s mail:[email protected] ZTTCE12.00MG Ceramic Resonator 8.1.2 Section of package Package is made of corrugated paper with thickness of 0.8cm.Package has 10 inner boxes, each box has 1 reel(each reel for plastic bag) 8.1.3 Quantity of package Per plastic reel 3000pieces of Per inner box 5 reels Per package piezoelectric ceramic part 12 inner boxes （180000 pieces of piezoelectric ceramic part ） 8.1.4 Inner Box Dimensions 18 5± 96±2 ② 2 185±2 ③ ① NO. Name Quantity ① Inner Box 1 ② QC Label 1 ③ Label 1 http://www.luguang.cn mail:[email protected] ZTTCE12.00MG Ceramic Resonator 8.2 On reel pack, the following requirements are requested. 8.2.1 Reel Dimensions φA 180±3 φB W T 60min 8.4min 12.4max Pieces per reel Carrier tape size 3000typ. 8 8.2.3 Packing Method Sketch Map Blank Pocket 10 Pitches Loaded Pocket Blank Pocket 10 Pitches Leader 200mm Max 8.2.4Test Condition Of Peeling Strength Top Tape 70g ngth 20e tr S g n li Pee 10 max Carrier Tape http://www.luguang.cn mail:[email protected] ZTTCE12.00MG Ceramic Resonator 9．OTHER 9.1 Caution 9.1.1 Don’t apply excess mechanical stress to the component and terminals at soldering. Do not use this product with bend. 9.1.2 Do not clean or wash the component for it is not hermetically sealed. 9.1.3 Do not use strong acidity flux，more than 0.2wt% chlorine content，in flow soldering. 9.1.4 Don’t be close to fire. 9.1.5 This specification mentions the quality of the component as a single unit. Please insure the component is thoroughly evaluated in your application circuit 9.1.6 Expire date (Shelf life) of the products is six months after delivery under the conditions of a sealed and an unopened package. Please use the products within six months after delivery. If you store the products for a long time (more than six months), use carefully because the products may be degraded in the solderability or rusty. Please confirm solderability and characteristics for the products regularly. 9.1.7 Please contact us before using the product as automobile electronic component. 9.2 Notice 9.2.1 Please return one of this specification after your signature of acceptance. 9.2.2 When something gets doubtful with this specifications, we shall jointly work to get an agreement. http://www.luguang.cn mail:[email protected]