ELECTRONICS Transient Voltage Suppressors 5.0SMDJ Series Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Transient Voltage Suppressors - 5.0SMDJ Series Features UNI 1. Halogen-free 2. Rohs compliant 3. Typical maximum temperature coefficient 4. ΔVBR = 0.1% x VBR@25°C x ΔT 5. Glass passivated Chip junction in DO-214AB package BI 6. 5000W peak pulse capadility at 10×1000μs waveform, repetition rate (duty cycles):0.01% 7. Fast response time:typically less than 1.0ps from 0 Volts to BV min 8. Excellent clamping capability 9. Low incremental surge resistance 10. Typical IR less than 5μA above 12V BI Cathode 11. High temperature soldering guaranteed: 260°C/40 seconds / 0.375”, Anode 12. (9.5mm) lead length, 5lbs., (2.3kg) tension 13. Plastic package has underwriters laboratory flammability classification UNI 94v-0 Applications TVS devices are ideal for the protection of I/O interfaces,VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Mechanical Characteristics Rating Symbol Value Units PPPM 5000 Watts PD 6.5 Watts IFSM 300 Amps VF 5.0 V Operating junction and Storage Temperature Range. TJ,TSTG -55°C to 150°C °C Typical Thermal Resistance Junction to Lead RuJL 15 °C/W Typical Thermal Resistance Junction to Ambient RuJA 75 °C/W Peak Pulse Power Dissipation at TA=25°C by 10/1000μs Waveform (Fig.2)(Note 1), (Note 2) Power Dissipation on Infinite Heat Sink at TA=50°C Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25°C per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31” (8.0 × 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only,duty cycle=4 per minute maximum. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:1 Transient Voltage Suppressors - 5.0SMDJ Series Electriacl Characteristics Type Number Device Marking Code (UNI) (BI) UNI BI 5.0SMDJ12A 5.0SMDJ13A 5.0SMDJ14A 5.0SMDJ15A 5.0SMDJ16A 5.0SMDJ17A 5.0SMDJ18A 5.0SMDJ20A 5.0SMDJ22A 5.0SMDJ24A 5.0SMDJ26A 5.0SMDJ28A 5.0SMDJ30A 5.0SMDJ33A 5.0SMDJ36A 5.0SMDJ40A 5.0SMDJ43A 5.0SMDJ45A 5.0SMDJ48A 5.0SMDJ51A 5.0SMDJ54A 5.0SMDJ58A 5.0SMDJ60A 5.0SMDJ64A 5.0SMDJ70A 5.0SMDJ75A 5.0SMDJ78A 5.0SMDJ85A 5.0SMDJ90A 5.0SMDJ100A 5.0SMDJ110A 5.0SMDJ120A 5.0SMDJ130A 5.0SMDJ150A 5.0SMDJ160A 5.0SMDJ170A 5.0SMDJ12CA 5.0SMDJ13CA 5.0SMDJ14CA 5.0SMDJ15CA 5.0SMDJ16CA 5.0SMDJ17CA 5.0SMDJ18CA 5.0SMDJ20CA 5.0SMDJ22CA 5.0SMDJ24CA 5.0SMDJ26CA 5.0SMDJ28CA 5.0SMDJ30CA 5.0SMDJ33CA 5.0SMDJ36CA 5.0SMDJ40CA 5.0SMDJ43CA 5.0SMDJ45CA 5.0SMDJ48CA 5.0SMDJ51CA 5.0SMDJ54CA 5.0SMDJ58CA 5.0SMDJ60CA 5.0SMDJ64CA 5.0SMDJ70CA 5.0SMDJ75CA 5.0SMDJ78CA 5.0SMDJ85CA 5.0SMDJ90CA 5.0SMDJ100CA 5.0SMDJ110CA 5.0SMDJ120CA 5.0SMDJ130CA 5.0SMDJ150CA 5.0SMDJ160CA 5.0SMDJ170CA 5PEP 5PEQ 5PER 5PES 5PET 5PEU 5PEV 5PEW 5PEX 5PFZ 5PFE 5PFG 5PFK 5PFM 5PFP 5PFR 5PFT 5PFV 5PFX 5PFZ 5PGE 5PGG 5PGK 5PGM 5PGP 5PGR 5PGT 5PGV 5PGX 5PHZ 5PHE 5PHG 5PHK 5PHM 5PHP 5PHR 5BEP 5BEQ 5BER 5BES 5BET 5BEU 5BEV 5BEW 5BEX 5BFZ 5BFE 5BFG 5BFK 5BFM 5BFP 5BFR 5BFT 5BFV 5BFX 5BFZ 5BGE 5BGG 5BGK 5BGM 5BGP 5BGR 5BGT 5BGV 5BGX 5BHZ 5BHE 5BHG 5BHK 5BHM 5BHP 5BHR Reverse Stand-Off Breakdown Voltage@IT Voltage VRWM(V) VBR MIN.(V) VBR MAX.(V) 12.0 13.30 14.70 13.0 14.40 15.90 14.0 15.60 17.20 15.0 16.70 18.50 16.0 17.80 19.70 17.0 18.90 20.90 18.0 20.00 22.10 20.0 22.20 24.50 22.0 24.40 26.90 24.0 26.70 29.50 26.0 28.90 31.90 28.0 31.10 34.40 30.0 33.30 36.80 33.0 36.70 40.60 36.0 40.00 44.20 40.0 44.40 49.10 43.0 47.80 52.80 45.0 50.00 55.30 48.0 53.30 58.90 51.0 56.70 62.70 54.0 60.00 66.30 58.0 64.40 71.20 60.0 66.70 73.70 64.0 71.10 78.60 70.0 77.80 86.00 75.0 83.30 92.10 78.0 86.70 95.80 85.0 94.40 104.00 90.0 100.00 111.00 100.0 111.00 123.00 110.0 122.00 135.00 120.0 133.00 147.00 130.0 140.00 159.00 150.0 167.00 185.00 160.0 178.00 197.00 170.0 189.00 209.00 Test Current IT(mA) 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Peak Pulse Clamping Current Voltage@IPP VC(V) IPP(A) 19.9 252.00 21.5 233.00 23.2 216.00 24.4 205.00 26.0 193.00 27.6 181.00 29.2 172.00 32.4 155.00 35.5 141.00 38.9 129.00 42.1 119.00 45.4 110.00 48.4 103.00 53.3 93.90 58.1 86.10 64.5 77.60 69.4 72.10 72.7 68.80 77.4 64.70 82.4 60.70 87.1 57.50 93.6 53.50 96.8 51.70 103.0 48.60 113.0 44.30 121.0 41.40 126.0 39.70 137.0 36.50 146.0 34.30 162.0 30.90 177.0 28.30 193.0 26.00 209.0 24.00 243.0 20.60 259.0 19.30 275.0 18.20 Reverse Leakage @VRWM IR(µA) 800 500 200 100 50 20 10 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A, the VBR is +10% and VC is 5% higher than with A parts. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:2 Transient Voltage Suppressors - 5.0SMDJ Series Ratings and Characteristic Curves Figure 2 - Pulse Derating Curve Figure 1 - Peak Pulse Power Rating Curve A Figure 3 - Pulse Waveform Figure 4 - Typical Junction Capacitance 100000 Cj (pF) 10000 1000 Bi-directional V= OV Uni-directional V= OV Uni-directional @ VR 100 Bi-directional @ VR 10 1 1.0 Figure 5 - Steady State Power Derating Curve Circuit Protection System 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:3 Transient Voltage Suppressors - 5.0SMDJ Series Soldering Parameters Feflow Condition Pre Heat Lead-free assembly - Temperature Min (T s(min)) 150°C - Temperature Max (T s(min)) 200°C - Time (min to max) (t s) 60-180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max - Temperature (T L) (Liquidus) Reflow 217°C - Time (min to max) (t s) 60-150 seconds 260+0/-5 °C Peak Temperature (T P) Time within 5°C of actual peak Temperature (t p) 20-40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P) 8 minutes Max. Do not exceed 280°C Physical Specifications tp TP one Ramp-up Temperature (T) TL tL Critical Z P TL to T Weight 0.007 ounce, 0.21 grams JEDEC DO214AA. Molded plastic body over glass passivated junction Color band denotes cathode except Bidirectional. Matte Tin-plated leads, Solderable per JESD22-B102D Case Ts(max) Ts(min) Ramp-down ts Polarity Termina Preheat Time (t) Circuit Protection System Environmental Specifications Temperature Cycle JESD22-A104 Pressure Cooker JESD 22-A102 High Temp. Storage JESD22-A103 HTRB JESD22-A108 Thermal Shock JESD22-A106 Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:4 Transient Voltage Suppressors - 5.0SMDJ Series Dimensions Unit:mm DO-214AB (SMC J-Bend) Inches DIM Millimeters Min Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 24.00 - K - 0.165 - 4.200 L 0.094 - 2.400 - Part Numbering System 5.0SMDJ XXX C A 5% VOLTAGE TOLERANCE BI-DIRECTIONAL VOLTAGE SERIES Packaging Part Number Component Package Quantity Packaging Option Packaging Specification 5.0SMDJxxxXX DO-214AB 3000 Tape & Reel-16mm/13''tape EIA STD RS-481 5.0SMDJxxxXX-T7 DO-214AB 500 Tape & Reel – 16mm/7” tape EIA STD RS-481 Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:5 RuiLongYuan Electronics Co., Ltd. · Reproducing and modifying information of the document is prohibited without permission from Ruilongyuan International Inc. · Ruilongyuan International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. · Ruilongyuan International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. · Ruilongyuan International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. · Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications.Ruilongyuan International Inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. · The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify Ruilongyuan International Inc. for any damages resulting from such improper use or sale. Tel: +86-755-8290 8296 Circuit Protection System Fax: +86-755-8290 8002 E-mail: [email protected] Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:6