MICROCIRCUIT DATA SHEET Original Creation Date: 08/09/96 Last Update Date: 08/18/99 Last Major Revision Date: 05/12/99 MV54ACT241-X REV 1A0 Octal Buffers/Line Drivers With 3-State Outputs General Description The ACT241 is an octal buffer and line driver designed to be employed as a memory and address driver, clock driver and bus-oriented transmitter receiver which provides improved PC and board density. Industry Part Number NS Part Numbers 54ACT241 54ACT241E-QMLV * 54ACT241J-QMLV ** 54ACT241W-QMLV *** Prime Die J241 Controlling Document 5962-89847 Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 C +125 C -55 C +25 C +125 C -55 C +25 C +125 C -55 C +25 C +125 C -55 C MICROCIRCUIT DATA SHEET MV54ACT241-X REV 1A0 Features - Non-inverting TRI-STATE outputs drive bus lines or buffer memory address registers Outputs source/sink 24 mA ACT241 has TTL-compatible inputs Standard Military Drawing (SMD) - ACT241: 5962-8984701V2A*, VRA**, VSA*** 2 MICROCIRCUIT DATA SHEET MV54ACT241-X REV 1A0 (Absolute Maximum Ratings) (Note 1, 2, 3) Supply Voltage (Vcc) -0.5V to +6.0V DC Input Vi = Vi = DC Input Diode Current (Iik) -0.5V Vcc +0.5V Voltage (Vi) -20 mA +20 mA -0.5V to Vcc +0.5V DC Output Diode Current (Iok) Vo = -0.5V Vo = Vcc +0.5V DC Output Voltage (Vo) -20 mA +20 mA -0.5V to Vcc +0.5V DC Vcc or Ground Current per Pin (Icc or Ignd) +100 mA Storage Temperature (Tstg) -65 C to +150 C Junction Temperature (Tj) CDIP DC Output Current (Iout) per Output Pin 175 C +50 mA Lead Temperature (soldering, 10 seconds) +300 C Thermal Resistance, junction-to-case (jc) see MIL-STD 1835 Maximum Power Dissipation (pd) 500 mW Note 1: Note 2: Note 3: Stresses above the absolute maximum rating may cause damage to the device. Extended operation at the maximum levels may degrade and affect reliability. Unless otherwise specified, all voltages are referenced to GND. The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of -55C to +125C. Recommended Operating Conditions (Note 1, 2) Supply Voltage (Vcc) 4.5V to 5.5V Input Voltage (Vi) 0V to Vcc Output Voltage (Vo) 0V to Vcc Operating Temperature (Ta) -55 C to +125 C Minimum Vin VCC Maximum Input Edge Rate (Delta V/Delta t) from 0.8V to 2.0V or from 2.0V to 0.8V 4.5V to 5.5V Low Level Input Voltage (Vil) 125 mV/ns 0.8 V Minimum High Level Input Voltage (Vih) 2.0 V Maximum High Level Output Current (Ioh) -24 mA Maximum Low Level Output Current (Iol) +24 mA 3 MICROCIRCUIT DATA SHEET MV54ACT241-X REV 1A0 Note 1: Note 2: Unless otherwise noted, all voltages are referenced to GND. The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of -55C to +125C. 4 MICROCIRCUIT DATA SHEET MV54ACT241-X REV 1A0 Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: VCC 4.5V to 5.5V, Temp. Range: -55C to 125C. SYMBOL IIH IIL VOL PARAMETER High Level Input Current Low Level Input Current Low Level Output Voltage CONDITIONS NOTES VCC=5.5V, VM=5.5V, VINL=0.0V, VINH=5.5V PINNAME MIN MAX UNIT SUBGROUPS 1, 5 INPUT 0.1 uA 1 1, 5 INPUT 1.0 uA 2 1, 5 INPUT -0.1 uA 1 1, 5 INPUT -1.0 uA 2 VCC=4.5V, VINH=4.5V, VINL=0.0V, IOL=50uA, VIH=2.0V, VIL=0.8V 1, 3 OUTPUT 0.1 V 1, 2, 3 VCC=5.5V, IOL=50uA, VINL=0.0V, VINH=5.5V, VIH=2.0V, VIL=0.8V 1, 3 OUTPUT 0.1 V 1, 2, 3 VCC=4.5V, IOL=24.0mA, VIL=0.8V, VIH=2.0V, VINL=0.0V, VINH=4.5V 1, 3 OUTPUT 0.4 V 1, 3 1, 3 OUTPUT 0.5 V 2 1, 3 OUTPUT 0.4 V 1, 3 1, 3 OUTPUT 0.5 V 2 1.65 V 1, 2, 3 VCC=5.5V, VM=0.0V, VINH=5.5V, VINL=0.0V VCC=5.5V, VIH=2.0V, VIL=0.8V, IOL=24mA, VINL=0.0V, VINH=5.5V VIOL Dynamic output current LOW VCC=5.5V, IOL=50.0mA, VINH=5.5V, VINL=0.0V 1, OUTPUT 3, 6 VOH High Level Output Voltage VCC=4.5V, VIL=0.8V, VIH=2.0V, IOH=-50.0uA, VINH=4.5V, VINL=0.0V 1, 3 OUTPUT 4.40 V 1, 2, 3 VCC=4.5V, VIL=0.8V, VIH=2.0V, IOH=-24.0mA, VINH=4.5V, VINL=0.0V 1, 3 OUTPUT 3.70 V 1, 2, 3 VCC=5.5V, VIL=0.8V, VIH=2.0V, IOH=-24.0mA, VINH=5.5V, VINL=0.0V 1, 3 OUTPUT 4.70 V 1, 2, 3 VCC=5.5V, VIL=0.8V, VIH=2.0V, IOH=-50.0uA, VINH=5.5V, VINL=0.0V 1, 3 OUTPUT 5.40 V 1, 2, 3 3.85 V 1, 2, 3 VIOH Dynamic output current HIGH VCC=5.5V, IOH=-50.0mA, VINH=5.5V, VINL=0.0V 1, OUTPUT 3, 6 ICCH Supply Current Outputs HIGH VCC=5.5V, VINH=5.5V, VINL=0.0V 1, 5 VCC 100 nA 1 1, 5 VCC 40.0 uA 2 1, 5 VCC 100 nA 1 1, 5 VCC 40.0 uA 2 1, 5 VCC 100 nA 1 1, 5 VCC 40.0 uA 2 1, 5 VCC 100 nA 1 1, 5 VCC 40.0 uA 2 1, 3 VCC 1.0 mA 1, 2 1, 3 VCC 1.6 mA 3 ICCL ICCZ ICCF ICCT Supply Current Outputs LOW Supply Current Outputs TRI-STATE Supply Current Functional Supply Current VCC=5.5V, VINL=0.0V, VINH=5.5V VCC=5.5V, VINL=0.0V, VINH=5.5V VCC=5.5V, VINL=0.0V, VINH=5.5V VCC=5.5V, VIHT=VCC-2.1V, VINH=5.5V, VINL=0.0V 5 MICROCIRCUIT DATA SHEET MV54ACT241-X REV 1A0 Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: VCC 4.5V to 5.5V, Temp. Range: -55C to 125C. SYMBOL CONDITIONS TRI-STATE Output Leakage Current HIGH VCC=5.5V, VM=5.5V, VIH=2.0V, VIL=0.8V, VINH=5.5V, VINL=0.0V TRI-STATE Output Leakage Current LOW VCC=5.5V, VM=0.0V, VIH=2.0V, VIL=0.8V, VINH=5.5V, VINL=0.0V VIC+ Positive Input Clamp Voltage VCC=0.0V, IM=1.0mA 8, 9 INPUT VIC- Negative Input Clamp Voltage VCC=OPEN, IM=-1.0mA 8, 9 INPUT VOLP Low Level Ground Bounce VLD=2.5V, IOL=+24mA, VCC=4.5V 7 VOHV High Level Ground Bounce VLD=2.5V, IOH=-24mA, VCC=4.5V CIN Input Capacitance COUT CPD IOZH IOZL NOTES PINNAME PARAMETER MIN MAX UNIT SUBGROUPS 1, 5 OUTPUT 0.50 uA 1 1, 5 OUTPUT 10.0 uA 2 1, 5 OUTPUT -0.50 uA 1 1, 5 OUTPUT -10.0 uA 2 0.40 1.50 V 1 -0.40 -1.50 V 1 OUTPUT 2.0 V 4 7 OUTPUT 2.0 V 4 VCC=0.0V, Tc=+25C 7 INPUT 8.0 pF 4 Output Capacitance VCC=5.5V, Tc=+25C 7 OUTPUT 15.0 pF 4 Power Dissipation Capacitance VCC=5.0V, Tc=+25C 7 INPUT 70 pF 4 6 MICROCIRCUIT DATA SHEET MV54ACT241-X REV 1A0 Electrical Characteristics AC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pF, RL=500 OHMS, Temp Range: -55C to 125C SYMBOL tpLH tpHL tpZH tpZL tpHZ tpLZ PARAMETER Propagation Delay Propagation Delay Output Enable Output Enable Output Disable Output Disable Note 1: Note 2: Note 3: Note 4: Note 5: Note Note Note Note 6: 7: 8: 9: CONDITIONS NOTES VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V PINNAME MIN MAX UNIT 2, 4 In to On 1.0 9.0 ns 9, 11 2, 4 In to On 1.0 10.0 ns 10 2, 4 In to On 1.0 9.0 ns 9, 11 2, 4 In to On 1.0 10.0 ns 10 2, 4 OE to On 1.0 9.0 ns 9, 11 2, 4 OE to On 1.0 11.5 ns 10 2, 4 OE to On 1.0 10.0 ns 9, 11 2, 4 OE to On 1.0 12.5 ns 10 2, 4 OE to On 1.0 10.5 ns 9, 11 2, 4 OE to On 1.0 12.5 ns 10 2, 4 OE to On 1.0 10.5 ns 9, 11 2, 4 OE to On 1.0 12.5 ns 10 Screen tested 100% on each device at +25C & +125C temperature, subgroups A1, 2 & 7. Screen tested 100% on each device at +25C temperature only, subgroup A9. Sample tested (Method 5005, Table 1) on each MFG. lot at +25C, +125C & -55C temperature, subgroups A1, 2, 3, 7 & 8. Sample tested (Method 5005, Table 1) on each MFG. lot at +25C, +125C & -55C temperature, subgroups A9, 10 & 11. Sample tested (Method 5005, Table 1) on each MFG. lot at +25C & +125C temperature, subgroups 1, 2, 7 & 8. Transmission line driving test, 2 MSEC duration MAX. GUARANTEED BUT NOT TESTED. Screen tested 100% on each device at +25C only. Sample tested (Method 5005, Table 1) at +25C only 7 SUBGROUPS MICROCIRCUIT DATA SHEET MV54ACT241-X REV 1A0 Revision History Rev ECN # 1A0 M0003500 08/18/99 Rel Date Originator Changes Linda Collins 1) Add ICCF to the DC electricals. 2) VOH test with VCC = 4.5V and IOH = -24mA, changed VIH from 2.2V to 2.0V. 8