SN54ABT16952, SN74ABT16952 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS082C – FEBRUARY 1991 – REVISED JANUARY 1997 D D D D D D D D SN54ABT16952 . . . WD PACKAGE SN74ABT16952 . . . DGG OR DL PACKAGE (TOP VIEW) Members of the Texas Instruments Widebus Family State-of-the-Art EPIC-ΙΙB BiCMOS Design Significantly Reduces Power Dissipation Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17 Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C Distributed VCC and GND Pin Configuration Minimizes High-Speed Switching Noise Flow-Through Architecture Optimizes PCB Layout High-Drive Outputs (–32-mA IOH, 64-mA IOL) Package Options Include Plastic 300-mil Shrink Small-Outline (DL) and Thin Shrink Small-Outline (DGG) Packages and 380-mil Fine-Pitch Ceramic Flat (WD) Package Using 25-mil Center-to-Center Spacings 1OEAB 1CLKAB 1CLKENAB GND 1A1 1A2 VCC 1A3 1A4 1A5 GND 1A6 1A7 1A8 2A1 2A2 2A3 GND 2A4 2A5 2A6 VCC 2A7 2A8 GND 2CLKENAB 2CLKAB 2OEAB description The ’ABT16952 are 16-bit registered transceivers that contain two sets of D-type flip-flops for temporary storage of data flowing in either direction. The ’ABT16952 can be used as two 8-bit transceivers or one 16-bit transceiver. Data on the A or B bus is stored in the registers on the low-to-high transition of the clock (CLKAB or CLKBA) input provided that the clock-enable (CLKENAB or CLKENBA) input is low. Taking the output-enable (OEAB or OEBA) input low accesses the data on either port. 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 23 34 24 33 25 32 26 31 27 30 28 29 1OEBA 1CLKBA 1CLKENBA GND 1B1 1B2 VCC 1B3 1B4 1B5 GND 1B6 1B7 1B8 2B1 2B2 2B3 GND 2B4 2B5 2B6 VCC 2B7 2B8 GND 2CLKENBA 2CLKBA 2OEBA To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. The SN54ABT16952 is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74ABT16952 is characterized for operation from –40°C to 85°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus and EPIC-ΙΙB are trademarks of Texas Instruments Incorporated. Copyright 1997, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ABT16952, SN74ABT16952 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS082C – FEBRUARY 1991 – REVISED JANUARY 1997 FUNCTION TABLE† INPUTS OUTPUT B CLKENAB CLKAB OEAB A H X L X X L L X L ↑ L L L L ↑ L H H B0‡ B0‡ X X H X Z † A-to-B data flow is shown; B-to-A data flow is similar, but uses CLKENBA, CLKBA, and OEBA. ‡ Level of B before the indicated steady-state input conditions were established 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ABT16952, SN74ABT16952 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS082C – FEBRUARY 1991 – REVISED JANUARY 1997 logic symbol† 1OEBA 56 54 1CLKENBA 1CLKBA 55 1 1OEAB 3 1CLKENAB 1CLKAB 2 29 2OEBA 31 2CLKENBA 2CLKBA 2OEAB 30 28 26 2CLKENAB 2CLKAB 1A1 27 5 EN3 G1 1C5 EN4 G2 2C6 EN9 G7 7C11 EN10 G8 8C12 3 6D 1A2 1A3 1A4 1A5 1A6 1A7 1A8 2A1 6 2A3 2A4 2A5 2A6 2A7 2A8 4 52 51 8 49 9 48 10 47 12 45 13 44 14 43 15 42 9 12D 2A2 5D 11D 1B1 1B2 1B3 1B4 1B5 1B6 1B7 1B8 2B1 10 16 41 17 40 19 38 20 37 21 36 23 34 24 33 2B2 2B3 2B4 2B5 2B6 2B7 2B8 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ABT16952, SN74ABT16952 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS082C – FEBRUARY 1991 – REVISED JANUARY 1997 logic diagram (positive logic) 1CLKENAB 1CLKAB 1OEBA 1A1 3 54 2 55 56 1 5 One of Eight Channels C1 CE 1D 52 1CLKENBA 1CLKBA 1OEAB 1B1 C1 CE 1D To Seven Other Channels 2CLKENAB 2CLKAB 2OEBA 26 31 27 30 29 28 One of Eight Channels 2A1 C1 CE 1D 15 C1 CE 1D To Seven Other Channels 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 42 2CLKENBA 2CLKBA 2OEAB 2B1 SN54ABT16952, SN74ABT16952 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS082C – FEBRUARY 1991 – REVISED JANUARY 1997 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (except I/O ports) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V Current into any output in the low state, IO: SN54ABT16952 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ABT16952 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51. recommended operating conditions (see Note 3) SN54ABT16952 VCC VIH Supply voltage VIL VI Low-level input voltage IOH IOL High-level output current ∆t/∆v Input transition rise or fall rate High-level input voltage SN74ABT16952 MIN MAX MIN MAX 4.5 5.5 4.5 5.5 2 2 0.8 Input voltage 0 Low-level output current Outputs enabled TA Operating free-air temperature NOTE 3: Unused pins (input or I/O) must be held high or low to prevent them from floating. –55 VCC –24 V V 0.8 0 UNIT VCC –32 V V mA 48 64 mA 10 10 ns/V 85 °C 125 –40 PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54ABT16952, SN74ABT16952 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS082C – FEBRUARY 1991 – REVISED JANUARY 1997 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH TEST CONDITIONS VCC = 4.5 V, VCC = 4.5 V, II = –18 mA IOH = –3 mA VCC = 5 V, VCC = 4 4.5 5V VOL VCC = 4 4.5 5V MIN MIN –1.2 MAX SN74ABT16952 MIN –1.2 2.5 IOH = –3 mA IOH = –24 mA 3 3 3 2 2 IOH = –32 mA IOL = 48 mA 2* IOZH‡ IOZL‡ VCC = 5.5 V, VCC = 5.5 V, VO = 2.7 V VO = 0.5 V Ioff VCC = 0, VCC = 5.5 V, VO = 5.5 V VI or VO ≤ 4.5 V VCC = 5.5 V, VO = 2.5 V Outputs high IO§ 0.55 0.55* 0.55 A or B ports VCC = 5.5 V, IO = 0, VI = VCC or GND Outputs high Outputs low Ci Control inputs Cio A or B ports ±1 ±100 ±100 ±100 50 50 50 µA –50 –50 –200 VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V 50 –50 –200 –50 –50 µA µA 50 µA –200 mA 2 2 2 35 35 2 2 2 0.5 0.5 0.5 mA mA 3 pF 8.5 pF * On products compliant to MIL-PRF-38535, this parameter does not apply. † All typical values are at VCC = 5 V. ‡ The parameters IOZH and IOZL include the input leakage current. § Not more than one output should be tested at a time, and the duration of the test should not exceed one second. ¶ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 µA ±100 35 Outputs disabled VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND ∆ICC¶ mV ±1 50 –100 V ±1 ±100 –50 V 2 0.55 IOL = 64 mA VI = VCC or GND A or B ports UNIT V 100 Control inputs ICEX 6 MAX –1.2 2.5 VCC = 5 5.5 5V V, ICC SN54ABT16952 2.5 Vhys II TA = 25°C TYP† MAX • DALLAS, TEXAS 75265 SN54ABT16952, SN74ABT16952 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS082C – FEBRUARY 1991 – REVISED JANUARY 1997 timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 1) VCC = 5 V, TA = 25°C fclock tw† Clock frequency Pulse duration, CLKAB or CLKBA high or low SN54ABT16952 SN74ABT16952 MIN MAX MIN MAX MIN MAX 0 150 0 150 0 150 3.3 3.3 3.3 3.5 3.5 3.5 CLKENAB or CLKENBA 3 3 3 A or B 1 1 1 CLKENAB or CLKENBA 1 1 1 tsu Setup time,, before CLKAB↑ or CLKBA↑ A or B th Hold time,, after CLKAB↑ or CLKBA↑ UNIT MHz ns ns ns † This parameter is warranted, but not production tested. switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) PARAMETER fmax tPLH tPHL tPZH tPZL tPHZ tPLZ FROM (INPUT) TO (OUTPUT) VCC = 5 V, TA = 25°C MIN SN54ABT16952 TYP MAX 1 2.6 3.9 1 4.4 1 4.3 1 2.6 4.2 1 4.6 1 4.5 1 2.5 3.8 1 4.7 1 4.6 1 2.8 5.1 1 6.1 1 6 1.7 3.4 4.7 1.7 6.1 1.7 5.5 1.3 3 3.9 1.3 4.8 1.3 4.2 150 CLK A or B OE A or B OE A or B MIN MAX SN74ABT16952 150 MIN UNIT MAX 150 MHz ns ns ns PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SN54ABT16952, SN74ABT16952 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS SCBS082C – FEBRUARY 1991 – REVISED JANUARY 1997 PARAMETER MEASUREMENT INFORMATION 500 Ω From Output Under Test S1 7V Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open 3V LOAD CIRCUIT Timing Input 1.5 V 0V tw tsu 3V th 3V 1.5 V Input 1.5 V 0V Data Input 1.5 V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION 3V 1.5 V Input 1.5 V 0V VOH 1.5 V Output 1.5 V VOL VOH 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 1.5 V 0V tPZL tPLZ Output Waveform 1 S1 at 7 V (see Note B) tPLH tPHL Output 3V Output Control tPHL tPLH 1.5 V Output Waveform 2 S1 at Open (see Note B) 1.5 V 3.5 V VOL + 0.3 V VOL tPHZ tPZH 1.5 V VOH – 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 27-Sep-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 74ABT16952DGGRE4 ACTIVE TSSOP DGG 56 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ABT16952DGGRG4 ACTIVE TSSOP DGG 56 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16952DGGR ACTIVE TSSOP DGG 56 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16952DL ACTIVE SSOP DL 56 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16952DLG4 ACTIVE SSOP DL 56 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16952DLR ACTIVE SSOP DL 56 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT16952DLRG4 ACTIVE SSOP DL 56 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN74ABT16952DGGR TSSOP DGG 56 2000 330.0 24.4 8.6 15.6 1.8 12.0 24.0 Q1 SN74ABT16952DLR SSOP DL 56 1000 330.0 32.4 11.35 18.67 3.1 16.0 32.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74ABT16952DGGR TSSOP DGG 56 2000 346.0 346.0 41.0 SN74ABT16952DLR SSOP DL 56 1000 346.0 346.0 49.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated