FAIRCHILD 74ACTQ244MSA

74ACQ244, 74ACTQ244
Quiet Series™ Octal Buffer/Line Driver with 3-STATE
Outputs
Features
General Description
■ ICC and IOZ reduced by 50%
■ Guaranteed simultaneous switching noise level and
The ACQ/ACTQ244 is an octal buffer and line driver
designed to be employed as a memory address driver,
clock driver and bus oriented transmitter or receiver
which provides improved PC board density. The ACQ/
ACTQ utilizes Fairchild Quiet Series™ technology to
guarantee quiet output switching and improved dynamic
threshold performance. FACT Quiet Series™ features
GTO™ output control and undershoot corrector in addition to a split ground bus for superior performance.
dynamic threshold performance
■ Guaranteed pin-to-pin skew AC performance
■ Improved latch-up immunity
■ 3-STATE outputs drive bus lines or buffer memory
address registers
■ Outputs source/sink 24mA
■ Faster prop delays than the standard AC/ACT244
tm
Ordering Information
Order Number
Package
Number
Package Description
74ACQ244SC
M20B
20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300” Wide
Body
74ACQ244SJ
M20D
20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
74ACTQ244SC
M20B
20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300” Wide
Body
74ACTQ244SJ
M20D
20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
74ACTQ244QSC
MQA20
20-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150” Wide
74ACTQ244MSA
MSA20
20-Lead Shrink Small Outline Package (SSOP), EIAJ TYPE II, 5.3mm Wide
Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering number.
Connection Diagram
Pin Description
Pin Names
OE1, OE2
Description
3-STATE Output Enable Inputs
I0–I 7
Inputs
O0–O 7
Outputs
FACT™, Quiet Series™, FACT Quiet Series™, and GTO™ are trademarks of Fairchild Semiconductor Corporation.
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
March 2007
Truth Tables
IEE/IEC
Inputs
Outputs
OE1
In
Pins 12, 14, 16, 18
L
L
L
L
H
H
H
X
Z
Inputs
Outputs
OE2
In
Pins 3, 5, 7, 9
L
L
L
L
H
H
H
X
Z
H = HIGH Voltage Level
L = LOW Voltage Level
X = Immaterial
Z = High Impedance
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
2
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
Logic Symbol
Symbol
VCC
IIK
Parameter
Rating
Supply Voltage
–0.5V to +7.0V
DC Input Diode Current
VI = –0.5V
–20mA
VI = VCC + 0.5V
+20mA
VI
DC Input Voltage
IOK
DC Output Diode Current
–0.5V to VCC + 0.5V
VO = –0.5V
–20mA
VO = VCC + 0.5V
+20mA
VO
DC Output Voltage
–0.5V to VCC + 0.5V
IO
DC Output Source or Sink Current
±50mA
ICC or IGND DC VCC or Ground Current per Output Pin
TSTG
±50mA
Storage Temperature
–65°C to +150°C
DC Latch-Up Source or Sink Current
TJ
±300mA
Junction Temperature
140°C
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to absolute maximum ratings.
Symbol
VCC
Parameter
Rating
Supply Voltage
ACQ
2.0V to 6.0V
ACTQ
4.5V to 5.5V
VI
Input Voltage
0V to VCC
VO
Output Voltage
0V to VCC
TA
Operating Temperature
∆V / ∆t
–40°C to +85°C
125mV/ns
Minimum Input Edge Rate, ACQ Devices:
VIN from 30% to 70% of VCC, VCC @ 3.0V, 4.5V, 5.5V
∆V / ∆t
125mV/ns
Minimum Input Edge Rate, ACTQ Devices:
VIN from 0.8V to 2.0V, VCC @ 4.5V, 5.5V
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
3
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
Absolute Maximum Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
TA = +25°C
Symbol
VIH
Parameter
Minimum HIGH Level
Input Voltage
VCC (V)
3.0
4.5
Conditions
VOUT = 0.1V or
VCC – 0.1V
5.5
VIL
Maximum LOW Level
Input Voltage
3.0
4.5
VOUT = 0.1V or
VCC – 0.1V
5.5
VOH
Minimum HIGH Level
Output Voltage
3.0
IOUT = –50µA
Typ.
TA = –40°C to +85°C
Guaranteed Limits
1.5
2.1
2.1
2.25
3.15
3.15
2.75
3.85
3.85
1.5
0.9
0.9
2.25
1.35
1.35
2.75
1.65
1.65
2.99
2.9
2.9
4.5
4.49
4.4
4.4
5.5
5.49
5.4
5.4
Units
V
V
V
VIN = VIL or VIH:
VOL
Maximum LOW Level
Output Voltage
3.0
IOH = –12mA
2.56
2.46
4.5
IOH = –24mA
3.86
3.76
–24mA(1)
5.5
IOH =
3.0
IOUT = 50µA
4.86
4.76
0.002
0.1
0.1
4.5
0.001
0.1
0.1
5.5
0.001
0.1
0.1
V
VIN = VIL or VIH:
3.0
IOL = 12mA
0.36
0.44
4.5
IOL = 24mA
0.36
0.44
5.5
IOL = 24mA(1)
0.36
0.44
Maximum Input
Leakage Current
5.5
VI = VCC, GND
±0.1
±1.0
µA
Minimum Dynamic
Output Current(2)
5.5
VOLD = 1.65V Max.
75
mA
5.5
VOHD = 3.85V Min.
–75
mA
Maximum Quiescent
Supply Current
5.5
VIN = VCC or GND
4.0
40.0
µA
Maximum 3-STATE
Leakage Current
5.5
VI (OE) = VIL, VIH;
VI = VCC, GND;
VO = VCC, GND
±0.25
±2.5
µA
VOLP
Quiet Output Maximum
Dynamic VOL
5.0
Figures 1 & 2(4)
1.1
1.5
V
VOLV
Quiet Output Minimum
Dynamic VOL
5.0
Figures 1 & 2(4)
–0.6
–1.2
V
VIHD
Minimum HIGH Level
Dynamic Input Voltage
5.0
(5)
3.1
3.5
V
VILD
Maximum LOW Level
Dynamic Input Voltage
5.0
(5)
1.9
1.5
V
IIN
(3)
IOLD
IOHD
ICC(3)
IOZ
Notes:
1. All outputs loaded thresholds on input associated with output under test.
2. Maximum test duration 2.0ms, one output loaded at a time.
3. IIN and ICC @ 3.0V are guaranteed to be less than or equal to the respective limit @ 5.5V VCC.
4. Max number of outputs defined as (n). Data Inputs are driven 0V to 5V. One output @ GND.
5. Max number of Data Inputs (n) switching. (n – 1) Inputs switching 0V to 5V (ACQ). Input-under-test switching:
5V to threshold (VILD), 0V to threshold (VIHD), f = 1MHz.
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
4
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
DC Electrical Characteristics for ACQ
TA = +25°C
Symbol
VIH
VIL
VOH
Parameter
VCC (V)
Conditions
Typ.
TA = –40°C to +85°C
Guaranteed Limits
VOUT = 0.1V or
VCC – 0.1V
1.5
2.0
2.0
1.5
2.0
2.0
VOUT = 0.1V or
VCC – 0.1V
1.5
0.8
0.8
5.5
1.5
0.8
0.8
4.5
IOUT = –50µA
4.49
4.4
4.4
5.49
5.4
5.4
3.86
3.76
4.86
4.76
0.001
0.1
0.1
0.001
0.1
0.1
0.36
0.44
0.36
0.44
Minimum HIGH Level
Input Voltage
4.5
Maximum LOW Level
Input Voltage
4.5
Minimum HIGH Level
Output Voltage
5.5
5.5
Units
V
V
V
VIN = VIL or VIH:
4.5
VOL
Maximum LOW Level
Output Voltage
IOH = –24mA
–24mA(6)
5.5
IOH =
4.5
IOUT = 50µA
5.5
V
VIN = VIL or VIH:
4.5
IOL = 24mA
24mA(6)
5.5
IOL =
Maximum Input
Leakage Current
5.5
VI = VCC, GND
±0.1
±1.0
µA
IOZ
Maximum 3-STATE
Leakage Current
5.5
VI = VIL, VIH;
VO = VCC, GND
±0.25
±2.5
µA
ICCT
Maximum ICC/Input
5.5
VI = VCC – 2.1V
1.5
mA
IOLD
Minimum Dynamic
Output Current(7)
5.5
VOLD = 1.65V Max.
75
mA
5.5
VOHD = 3.85V Min.
–75
mA
Maximum Quiescent
Supply Current
5.5
VIN = VCC or GND
40.0
µA
VOLP
Quiet Output Maximum
Dynamic VOL
5.0
Figures 1 & 2(8)
1.1
1.5
V
VOLV
Quiet Output Minimum
Dynamic VOL
5.0
Figures 1 & 2(8)
–0.6
–1.2
V
VIHD
Minimum HIGH Level
Dynamic Input Voltage
5.0
(9)
1.9
2.2
V
VILD
Maximum LOW Level
Dynamic Input Voltage
5.0
(9)
1.2
0.8
V
IIN
(3)
IOHD
ICC
(3)
0.6
4.0
Notes:
6. All outputs loaded thresholds on input associated with output under test.
7. Maximum test duration 2.0ms, one output loaded at a time.
8. Max number of outputs defined as (n). Data Inputs are driven 0V to 3V. One output @ GND.
9. Max number of Data Inputs (n) switching. (n–1) Inputs switching 0V to 3V (ACTQ). Input-under-test switching:
3V to threshold (VILD), 0V to threshold (VIHD), f = 1 MHz.
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
5
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
DC Electrical Characteristics for ACTQ
TA = +25°C,
CL = 50pF
Symbol
tPHL, tPLH
tPZL , tPZH
tPHZ, tPLZ
Parameter
TA = –40°C to +85°C,
CL = 50pF
VCC (V)(10)
Min.
Typ.
Max.
Min.
Max.
Units
3.3
2.0
7.0
9.0
2.0
9.5
ns
5.0
1.5
5.0
6.0
1.5
6.5
Propagation Delay Data
to Output
Output Enable Time
Output Disable Time
tOSHL, tOSLH Output to Output Skew
Data to Output(11)
3.3
2.5
8.0
12.0
2.5
12.5
5.0
1.5
6.5
8.0
1.5
8.5
3.3
1.0
9.0
13.5
1.0
14.0
5.0
1.0
7.5
9.0
1.0
9.5
3.3
1.0
1.5
1.5
5.0
0.5
1.0
1.0
ns
ns
ns
Note:
10. Voltage range 5.0 is 5.0V ± 0.5V. Voltage range 3.3 is 3.3V ± 0.3V.
11. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate
outputs of the same device. The specification applies to any outputs switching in the same direction, either
HIGH-to-LOW (tOSHL) or LOW-to-HIGH (tOSLH). Parameter guaranteed by design.
AC Electrical Characteristics for ACTQ
TA = +25°C,
CL = 50pF
TA = –40°C to +85°C,
CL = 50pF
VCC (V)(12)
Min.
Typ.
Max.
Min.
Max.
Units
5.0
1.5
5.5
6.5
1.5
7.0
ns
Output Enable Time
5.0
1.5
7.0
8.5
1.5
9.0
ns
Output Disable Time
5.0
1.0
8.0
9.5
1.0
10.0
ns
0.5
1.0
1.0
ns
Symbol
Parameter
tPHL, tPLH
Propagation Delay,
Data to Output
tPZL, tPZH
tPHZ, tPLZ
tOSHL, tOSLH Output to Output Skew,
Data to Output(13)
5.0
Notes:
12. Voltage range 5.0 is 5.0V ± 0.5V.
13. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate
outputs of the same device. The specification applies to any outputs switching in the same direction, either
HIGH-to-LOW (tOSHL) or LOW-to-HIGH (tOSLH). Parameter guaranteed by design.
Capacitance
Symbol
Parameter
Conditions
Typ.
Units
CIN
Input Capacitance
VCC = OPEN
4.5
pF
CPD
Power Dissipation Capacitance
VCC = 5.0V
70
pF
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
6
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
AC Electrical Characteristics for ACQ
VOLP/VOLV and VOHP/V OHV:
The setup of a noise characteristics measurement is critical to the accuracy and repeatability of the tests. The
following is a brief description of the setup used to measure the noise characteristics of FACT.
■ Determine the quiet output pin that demonstrates the
greatest noise levels. The worst case pin will usually
be the furthest from the ground pin. Monitor the output
voltages using a 50Ω coaxial cable plugged into a
standard SMB type connector on the test fixture. Do
not use an active FET probe.
■ Measure VOLP and VOLV on the quiet output during
the worst case active and enable transition. Measure
VOHP and VOHV on the quiet output during the worst
case active and enable transition.
■ Verify that the GND reference recorded on the
oscilloscope has not drifted to ensure the accuracy
and repeatability of the measurements.
Equipment:
Hewlett Packard Model 8180A Word Generator
PC-163A Test Fixture
Tektronics Model 7854 Oscilloscope
Procedure:
1. Verify Test Fixture Loading: Standard Load 50pF,
500Ω.
2. Deskew the HFS generator so that no two channels
have greater than 150ps skew between them. This
requires that the oscilloscope be deskewed first. It is
important to deskew the HFS generator channels
before testing. This will ensure that the outputs switch
simultaneously.
VILD and VIHD:
■ Monitor one of the switching outputs using a 50Ω
coaxial cable plugged into a standard SMB type
connector on the test fixture. Do not use an active
FET probe.
■ First increase the input LOW voltage level, VIL, until
the output begins to oscillate or steps out a min of 2ns.
Oscillation is defined as noise on the output LOW
level that exceeds VIL limits, or on output HIGH levels
that exceed VIH limits. The input LOW voltage level at
which oscillation occurs is defined as VILD.
■ Next decrease the input HIGH voltage level, VIH, until
the output begins to oscillate or steps out a min of 2ns.
Oscillation is defined as noise on the output LOW
level that exceeds VIL limits, or on output HIGH levels
that exceed VIH limits. The input HIGH voltage level at
which oscillation occurs is defined as VIHD.
■ Verify that the GND reference recorded on the
oscilloscope has not drifted to ensure the accuracy
and repeatability of the measurements.
3. Terminate all inputs and outputs to ensure proper
loading of the outputs and that the input levels are at
the correct voltage.
4. Set the HFS generator to toggle all but one output at
a frequency of 1MHz. Greater frequencies will
increase DUT heating and effect the results of the
measurement.
5. Set the HFS generator input levels at 0V LOW and 3V
HIGH for ACT devices and 0V LOW and 5V HIGH for
AC devices. Verify levels with an oscilloscope.
Notes:
14. VOHV and VOLP are measured with respect to ground
reference.
15. Input pulses have the following characteristics:
f = 1MHz, tr = 3ns, tf = 3ns, skew < 150ps.
Figure 1. Quiet Output Noise Voltage Waveforms
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
Figure 2. Simultaneous Switching Test Circuit
www.fairchildsemi.com
7
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
FACT Noise Characteristics
Dimensions are in inches (millimeters) unless otherwise noted.
Figure 3. 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300" Wide
Package Number M20B
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
8
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
Physical Dimensions
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
Physical Dimensions (Continued)
Dimensions are in millimeters unless otherwise noted.
Figure 4. 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
Package Number M20D
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
9
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
Physical Dimensions (Continued)
Dimensions are in millimeters unless otherwise noted.
Figure 5. 20-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150" Wide
Package Number MQA20
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
10
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
Physical Dimensions (Continued)
Dimensions are in millimeters unless otherwise noted.
Figure 6. 20-Lead Shrink Small Outline Package (SSOP), JEDEC MO-150, 5.3mm Wide
Package Number MSA20
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
11
®
ACEx
Across the board. Around the world.¥
ActiveArray¥
Bottomless¥
Build it Now¥
CoolFET¥
CROSSVOLT¥
CTL™
Current Transfer Logic™
DOME¥
2
E CMOS¥
®
EcoSPARK
EnSigna¥
FACT Quiet Series™
®
FACT
®
FAST
FASTr¥
FPS¥
®
FRFET
GlobalOptoisolator¥
GTO¥
HiSeC¥
i-Lo¥
ImpliedDisconnect¥
IntelliMAX¥
ISOPLANAR¥
MICROCOUPLER¥
MicroPak¥
MICROWIRE¥
MSX¥
MSXPro¥
OCX¥
OCXPro¥
®
OPTOLOGIC
®
OPTOPLANAR
PACMAN¥
POP¥
®
Power220
®
Power247
PowerEdge¥
PowerSaver¥
®
PowerTrench
Programmable Active Droop¥
®
QFET
QS¥
QT Optoelectronics¥
Quiet Series¥
RapidConfigure¥
RapidConnect¥
ScalarPump¥
SMART START¥
®
SPM
STEALTH™
SuperFET¥
SuperSOT¥-3
SuperSOT¥-6
SuperSOT¥-8
SyncFET™
TCM¥
®
The Power Franchise
®
TinyLogic
TINYOPTO¥
TinyPower¥
TinyWire¥
TruTranslation¥
PSerDes¥
®
UHC
UniFET¥
VCX¥
Wire¥
™
TinyBoost¥
TinyBuck¥
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS
HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE
APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER
ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S
WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body or
(b) support or sustain life, and (c) whose failure to perform
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to
result in a significant injury of the user.
2. A critical component in any component of a life support,
device, or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Advance Information
Formative or In Design
This datasheet contains the design specifications for product
development. Specifications may change in any manner without notice.
Definition
Preliminary
First Production
This datasheet contains preliminary data; supplementary data will be
published at a later date. Fairchild Semiconductor reserves the right to
make changes at any time without notice to improve design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild Semiconductor
reserves the right to make changes at any time without notice to improve
design.
Obsolete
Not In Production
This datasheet contains specifications on a product that has been
discontinued by Fairchild Semiconductor. The datasheet is printed for
reference information only.
Rev. I24
©1989 Fairchild Semiconductor Corporation
74ACQ244, 74ACTQ244 Rev. 1.3
www.fairchildsemi.com
12
74ACQ244, 74ACTQ244 Quiet Series™ Octal Buffer/Line Driver with 3-STATE Outputs
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an
exhaustive list of all such trademarks.