80C32/80C52 MATRA MHS CMOS 0 to 44 MHz Single-chip 8 Bit Microcontroller Description MHS’s 80C52 and 80C32 are high performance CMOS versions of the 8052/8032 NMOS single chip 8 bit µC. The fully static design of the MHS 80C52/80C32 allows to reduce system power consumption by bringing the clock frequency down to any value, even DC, without loss of data. The 80C52 retains all the features of the 8052 : 8 K bytes of ROM ; 256 bytes of RAM ; 32 I/O lines ; three 16 bit timers ; a 6-source, 2-level interrupt structure ; a full duplex serial port ; and on-chip oscillator and clock circuits. In addition, the 80C52 has 2 software-selectable 80C32 : Romless version of the 80C52 80C32/80C52-L16 : Low power version Vcc : 2.7 – 5.5 V Freq : 0-16 MHz 80C32/80C52-12 : 0 to 12 MHz 80C32/80C52-16 : 0 to 16 MHz 80C32/80C52-20 : 0 to 20 MHz 80C32/80C52-25 : 0 to 25 MHz 80C32/80C52-30 : 0 to 30 MHz modes of reduced activity for further reduction in power consumption. In the idle mode the CPU is frozen while the RAM, the timers, the serial port and the interrupt system continue to function. In the power down mode the RAM is saved and all other functions are inoperative. The 80C32 is identical to the 80C52 except that it has no on-chip ROM. MHS’s 80C52/80C32 are manufactured using SCMOS process which allows them to run from 0 up to 44 MHz with Vcc = 5 V. MHS’s 80C52 and 80C32 are also available at 16 MHz with 2.7 V < VCC < 5.5 V. 80C32/80C52-36 : 0 to 36 MHz 80C32-40 : 0 to 40 MHz* 80C32-42 : 0 to 42 MHz* 80C32-44 : 0 to 44 MHz* * 0 to 70°C temperature range. For other speed and temperature range availability please consult your sales office. Features Power control modes 256 bytes of RAM 8 Kbytes of ROM (80C52) 32 programmable I/O lines Three 16 bit timer/counters 64 K program memory space 64 K data memory space Fully static design 0.8µ CMOS process Boolean processor 6 interrupt sources Programmable serial port Temperature range : commercial, industrial, automotive, military Optional Secret ROM : Encryption Secret TAG : Identification number Rev. E (31/08/95) 1 80C32/80C52 MATRA MHS Interface Figure 1. Block Diagram 2 Rev. E (31/08/95) 80C32/80C52 MATRA MHS P0.3/A3 P0.2/A2 P0.1/A1 P0.0/A0 VCC NC P1.0/T2 P1.1/T2EX P1.2 P1.3 P1.4 Figure 2. Pin Configuration P1.5 P0.4/A4 P1.6 P0.5/A5 P1.7 P0.6/A6 RST P0.7/A7 EA RxD/P3.0 80C32/80C52 NC NC ALE TxD/P3.1 P2.4/A11 P2.2/A9 P2.3/A10 P2.1/A8 NC P2.5/A12 P2.0/A7 T1/P3.5 VSS P2.6/A13 XTAL1 T0/P3.4 XTAL2 P2.7/A14 RD/P3.7 PSEN INT1/P3.3 WR/P3.6 INT0/P3.2 LCC A3/P03 A2/P02 A1/P01 VCC A0/P00 P10 /T2 NC P11 /T2EX P12 P13 P14 DIL P15 P04 /A4 P16 P05 /A5 P17 P06 /A6 RST P07 /A7 RxD/P30 EA 80C32/80C52 NC NC ALE TxD/P31 P24 /A12 P23 /A11 P22 /A10 P21 /A9 P20 /A8 NC V SS P25 /A13 XTAL1 P26 /A14 T1/P35 XTAL2 P27 /A15 T0/P34 RD/P37 PSEN INT1/P33 WR/P36 INT0/P32 Flat Pack Diagrams are for reference only. Package sizes are not to scale. Rev. E (31/08/95) 3 80C32/80C52 MATRA MHS Pin Description VSS Circuit ground potential. VCC Supply voltage during normal, Idle, and Power Down operation. Port 0 Port 0 is an 8 bit open drain bi-directional I/O port. Port 0 pins that have 1’s written to them float, and in that state can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external Program and Data Memory. In this application it uses strong internal pullups when emitting 1’s. Port 0 also outputs the code bytes during program verification in the 80C52. External pullups are required during program verification. Port 0 can sink eight LS TTL inputs. Memory that use 16 bit addresses (MOVX @DPTR). In this application, it uses strong internal pullups when emitting 1’s. During accesses to external Data Memory that use 8 bit addresses (MOVX @Ri), Port 2 emits the contents of the P2 Special Function Register. It also receives the high-order address bits and control signals during program verification in the 80C52. Port 2 can sink/source three LS TTL inputs. It can drive CMOS inputs without external pullups. Port 3 Port 3 is an 8 bit bi-directional I/O port with internal pullups. Port 3 pins that have 1’s written to them are pulled high by the internal pullups, and in that state can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (ILL, on the data sheet) because of the pullups. It also serves the functions of various special features of the MHS 51 Family, as listed below. Port Pin P3.0 P3.1 P3.2 P3.3 P3.4 P3.5 P3.6 P3.7 Port 1 Port 1 is an 8 bit bi-directional I/O port with internal pullups. Port 1 pins that have 1’s written to them are pulled high by the internal pullups, and in that state can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL, on the data sheet) because of the internal pullups. Port 1 also receives the low-order address byte during program verification. In the 80C52, Port 1 can sink/ source three LS TTL inputs. It can drive CMOS inputs without external pullups. 2 inputs of PORT 1 are also used for timer/counter 2 : P1.0 [T2] : External clock input for timer/counter 2. P1.1 [T2EX] : A trigger input for timer/counter 2, to be reloaded or captured causing the timer/counter 2 interrupt. Alternate Function RXD (serial input port) TXD (serial output port) INT0 (external interrupt 0) INT1 (external interrupt 1) TD (Timer 0 external input) T1 (Timer 1 external input) WR (external Data Memory write strobe) RD (external Data Memory read strobe) Port 3 can sink/source three LS TTL inputs. It can drive CMOS inputs without external pullups. RST A high level on this for two machine cycles while the oscillator is running resets the device. An internal pull-down resistor permits Power-On reset using only a capacitor connected to VCC. As soon as the Reset is applied (Vin), PORT 1, 2 and 3 are tied to one. This operation is achieved asynchronously even if the oscillator does not start-up. Port 2 Port 2 is an 8 bit bi-directional I/O port with internal pullups. Port 2 pins that have 1’s written to them are pulled high by the internal pullups, and in that state can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (ILL, on the data sheet) because of the internal pullups. Port 2 emits the high-order address byte during fetches from external Program Memory and during accesses to external Data 4 ALE Address Latch Enable output for latching the low byte of the address during accesses to external memory. ALE is activated as though for this purpose at a constant rate of 1/6 the oscillator frequency except during an external data memory access at which time on ALE pulse is skipped. ALE can sink/source 8 LS TTL inputs. It can drive CMOS inputs without an external pullup. Rev. E (31/08/95) 80C32/80C52 MATRA MHS 1 FFFH). When EA is held low, the CPU executes only out of external Program Memory. EA must not be floated. PSEN Program Store Enable output is the read strobe to external Program Memory. PSEN is activated twice each machine cycle during fetches from external Program Memory. (However, when executing out of external Program Memory, two activations of PSEN are skipped during each access to external Data Memory). PSEN is not activated during fetches from internal Program Memory. PSEN can sink/source 8 LS TTL inputs. It can drive CMOS inputs without an external pullup. EA When EA is held high, the CPU executes out of internal Program Memory (unless the Program Counter exceeds XTAL1 Input to the inverting amplifier that forms the oscillator. Receives the external oscillator signal when an external oscillator is used. XTAL2 Output of the inverting amplifier that forms the oscillator. This pin should be floated when an external oscillator is used. Idle And Power Down Operation Figure 3 shows the internal Idle and Power Down clock configuration. As illustrated, Power Down operation stops the oscillator. Idle mode operation allows the interrupt, serial port, and timer blocks to continue to function, while the clock to the CPU is gated off. These special modes are activated by software via the Special Function Register, PCON. Its hardware address is 87H. PCON is not bit addressable. Figure 3. Idle and Power Down Hardware. Symbol Position Name and Function SMOD PCON.7 – – – GF1 GF0 PD PCON.6 PCON.5 PCON.4 PCON.3 PCON.2 PCON.1 IDL PCON.0 Double Baud rate bit. When set to a 1, the baud rate is doubled when the serial port is being used in either modes 1, 2 or 3. (Reserved) (Reserved) (Reserved) General-purpose flag bit. General-purpose flag bit. Power Down bit. Setting this bit activates power down operation. Idle mode bit. Setting this bit activates idle mode operation. If 1’s are written to PD and IDL at the same time. PD takes, precedence. The reset value of PCON is (000X0000). Idle Mode PCON : Power Control Register (MSB) SMOD (LSB) – – Rev. E (31/08/95) – GF1 GF0 PD The instruction that sets PCON.0 is the last instruction executed before the Idle mode is activated. Once in the Idle mode the CPU status is preserved in its entirety : the Stack Pointer, Program Counter, Program Status Word, Accumulator, RAM and all other registers maintain their data during idle. Table 1 describes the status of the external pins during Idle mode. IDL 5 80C32/80C52 MATRA MHS There are three ways to terminate the Idle mode. Activation of any enabled interrupt will cause PCON.0 to be cleared by hardware, terminating Idle mode. The interrupt is serviced, and following RETI, the next instruction to be executed will be the one following the instruction that wrote 1 to PCON.0. The flag bits GF0 and GF1 may be used to determine whether the interrupt was received during normal execution or during the Idle mode. For example, the instruction that writes to PCON.0 can also set or clear one or both flag bits. When Idle mode is terminated by an enabled interrupt, the service routine can examine the status of the flag bits. The second way of terminating the Idle mode is with a hardware reset. Since the oscillator is still running, the hardware reset needs to be active for only 2 machine cycles (24 oscillator periods) to complete the reset operation. Power Down Mode The instruction that sets PCON.1 is the last executed prior to entering power down. Once in power down, the oscillator is stopped. The contents of the onchip RAM and the Special Function Register is saved during power down mode. The hardware reset initiates the Special Fucntion Register. In the Power Down mode, VCC may be lowered to minimize circuit power consumption. Care must be taken to ensure the voltage is not reduced until the power down mode is entered, and that the voltage is restored before the hardware reset is applied which freezes the oscillator. Reset should not be released until the oscillator has restarted and stabilized. Table 1 describes the status of the external pins while in the power down mode. It should be noted that if the power down mode is activated while in external program memory, the port data that is held in the Special Function Register P2 is restored to Port 2. If the data is a 1, the port pin is held high during the power down mode by the strong pullup, T1, shown in Figure 4. Table 1 : Status of the external pins during idle and power down modes. MODE PROGRAM MEMORY ALE PSEN PORT0 PORT1 PORT2 PORT3 Idle Internal 1 1 Port Data Port Data Port Data Port Data Idle External 1 1 Floating Port Data Address Port Data Power Down Internal 0 0 Port Data Port Data Port Data Port Data Power Down External 0 0 Floating Port Data Port Data Port Data Stop Clock Mode Figure 4. I/O Buffers in the 80C52 (Ports 1, 2, 3). Due to static design, the MHS 80C32/C52 clock speed can be reduced until 0 MHz without any data loss in memory or registers. This mode allows step by step utilization, and permits to reduce system power consumption by bringing the clock frequency down to any value. At 0 MHz, the power consumption is the same as in the Power Down Mode. I/O Ports The I/O buffers for Ports 1, 2 and 3 are implemented as shown in figure 4. 6 Rev. E (31/08/95) 80C32/80C52 MATRA MHS When the port latch contains a 0, all pFETS in figure 4 are off while the nFET is turned on. When the port latch makes a 0-to-1 transition, the nFET turns off. The strong pFET, T1, turns on for two oscillator periods, pulling the output high very rapidly. As the output line is drawn high, pFET T3 turns on through the inverter to supply the IOH source current. This inverter and T form a latch which holds the 1 and is supported by T2. When Port 2 is used as an address port, for access to external program of data memory, any address bit that contains a 1 will have his strong pullup turned on for the entire duration of the external memory access. When an I/O pin on Ports 1, 2, or 3 is used as an input, the user should be aware that the external circuit must sink current during the logical 1-to-0 transition. The maximum sink current is specified as ITL under the D.C. Specifications. When the input goes below approximately 2 V, T3 turns off to save ICC current. Note, when returning to a logical 1, T2 is the only internal pullup that is on. This will result in a slow rise time if the user’s circuit does not force the input line high. Figure 5. Crystal Oscillator. To drive the device from an external clock source, XTAL1 should be driven while XTAL2 is left unconnected as shown in figure 6. There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum high and low times specified on the Data Sheet must be observed. Figure 6. External Drive Configuration. Oscillator Characteristics XTAL1 and XTAL2 are the input and output respectively, of an inverting amplifier which is configured for use as an on-chip oscillator, as shown in figure 5. Either a quartz crystal or ceramic resonator may be used. Hardware Description Same as for the 80C51, plus a third timer/counter : Timer/Event Counter 2 Timer 2 is a 16 bit timer/counter like Timers 0 and 1, it can operate either as a timer or as an event counter. This is selected by bit C/T2 in the Special Function Register T2CON (Figure 1). It has three operating modes : “capture”, “autoload” and “baud rate generator”, which are selected by bits in T2CON as shown in Table 2. In the capture mode there are two options which are selected by bit EXEN2 in T2CON; If EXEN2 = 0, then Timer 2 is a 16 bit timer or counter which upon overflowing sets bit TF2, the Timer 2 overflow bit, which can be used to generate an interrupt. If EXEN2 = 1, then Timer 2 still does the above, but with the added feature Rev. E (31/08/95) that a 1-to-0 transition at external input T2EX causes the current value in the Timer 2 registers, TL2 and TH2, to be captured into registers RCAP2L and RCAP2H, respectively, (RCAP2L and RCAP2H are new Special Function Register in the 80C52). In addition, the transition at T2EX causes bit EXF2 in T2CON to be set, and EXF2, like TF2, can generate an interrupt. Table 2 : Timer 2 Operating Modes. RCLK + TCLK CP/RL2 TR2 0 0 1 X 0 1 X X 1 1 1 0 MODE 16 bit auto-reload 16 bit capture baud rate generator (off) 7 80C32/80C52 MATRA MHS with the 16 bit value in registers RCAP2L and RCAP2H, which are preset by software. If EXEN2 = 1, then Timer 2 still does the above, but with the added feature that a 1-to-0 transition at external input T2EX will also trigger the 16 bit reload and set EXF2. The capture mode is illustrated in Figure 7. Figure 7. Timer 2 in Capture Mode. The auto-reload mode is illustrated in Figure 8. Figure 8. Timer in Auto-Reload Mode. In the auto-reload mode there are again two options, which are selected by bit EXEN2 in T2CON.If EXEN2 = 0, then when Timer 2 rolls over it does not only set TF2 but also causes the Timer 2 register to be reloaded (MSB) (LSB) TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2 The baud rate generator mode is selected by : RCLK = 1 and/or TCLK = 1. 8 Symbol Position Name and Significance TF2 T2CON.7 Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set when either RCLK = 1 OR TCLK = 1. EXF2 T2CON.6 Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared by software. RCLK T2CON.5 Receive clock flag. When set, causes the serial port to use Timer2 overflow pulses for its receive clock in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock. TCLK T2CON.4 Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock. EXEN2 T2CON.3 Timer 2 external enable flag. When set, allows capture or reload to occur as a result of a negative transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX. TR2 T2CON.2 Start/stop control for Timer 2. A logic 1 starts the timer. C/T2 T2CON.1 Timer or counter select. (Timer 2) 0 = Internal timer (OSC/12) 1 = External event counter (falling edge triggered). CP/RL2 T2CON.0 Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN 2 = 1. When cleared, auto reloads will occur either with Timer 2 overflows or negative transition at T2EX when EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow. Rev. E (31/08/95) MATRA MHS 80C32/80C52 80C52 with Secret ROM 80C52 with Secret TAG Matra MHS offers 80C52 with the encrypted secret ROM option to secure the ROM code contained in the 80C52 microcontrollers. Matra MHS offers special 64-bit identifier called “SECRET TAG” on the microcontroller chip. The clear reading of the program contained in the ROM is made impossible due to an encryption through several random keys implemented during the manufacturing process. The keys used to do such encryption are selected randomwise and are definitely different from one microcontroller to another. This encryption is activated during the following phases : – Everytime a byte is addressed during a verify of the ROM content, a byte of the encryption array is selected. – MOVC instructions executed from external program memory are disabled when fetching code bytes from internal memory. – EA is sampled and latched on reset, thus all state modification are disabled. The Secret Tag option is available on both ROMless and masked microcontrollers. The Secret Tag feature allows serialization of each microcontroller for identification of a specific equipment. A unique number per device is implemented in the chip during manufacturing process. The serial number is a 64-bit binary value which is contained and addressable in the Special Function Registers (SFR) area. This Secret Tag option can be read-out by a software routine and thus enables the user to do an individual identity check per device. This routine is implemented inside the microcontroller ROM memory in case of masked version which can be kept secret (and then the value of the Secret Tag also) by using a ROM Encryption. For further information, please refer to the application note (ANM031) available upon request. For further information please refer to the application note (ANM053) available upon request. Rev. E (31/08/95) 9 80C32/80C52 MATRA MHS Electrical Characteristics Absolute Maximum Ratings* Ambiant Temperature Under Bias : C = commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 70 I = industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40 to 85 Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . –65 to + 150 Voltage on VCC to VSS . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to + 7 V Voltage on Any Pin to VSS . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W * This value is based on the maximum allowable die temperature and the thermal resistance of the package * Notice Stresses at or above those listed under “ Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect device reliability. DC Parameters TA = 0°C to 70°C ; VSS = 0 V ; VCC = 5 V ± 10 % ; F = 0 to 44 MHz TA = –40°C + 85°C ; VSS = 0 V ; VCC = 5 V ± 10 % ; F = 0 to 36 MHz SYMBOL MIN MAX UNIT – 0.5 0.2 Vcc – 0.1 V 0.2 Vcc + 1.4 Vcc + 0.5 V 0.7 Vcc Vcc + 0.5 V TEST CONDITIONS VIL Input Low Voltage VIH Input High Voltage (Except XTAL and RST) VIH1 Input High Voltage (for XTAL and RST) VOL Output Low Voltage (Port 1, 2 and 3) 0.3 0.45 1.0 V V V IOL = 100 µA IOL = 1.6 mA (note 2) IOL = 3.5 mA VOL1 Output Low Voltage (Port 0, ALE, PSEN) 0.3 0.45 1.0 V V V IOL = 200 µA IOL = 3.2 mA (note 2) IOL = 7.0 mA VOH Output High Voltage Port 1, 2, 3 Vcc – 0.3 V IOH = – 10 µA Vcc – 0.7 V IOH = – 30 µA Vcc – 1.5 V IOH = – 60 µA VCC = 5 V ± 10 % Vcc – 0.3 V IOH = – 200 µA Vcc – 0.7 V IOH = – 3.2 mA Vcc – 1.5 V IOH = – 7.0 mA VCC = 5 V ± 10 % VOH1 Output High Voltage (Port 0, ALE, PSEN) IIL Logical 0 Input Current (Ports 1, 2 and 3) – 50 µA Vin = 0.45 V ILI Input leakage Current ± 10 µA 0.45 < Vin < Vcc ITL Logical 1 to 0 Transition Current (Ports 1, 2 and 3) – 650 µA Vin = 2.0 V IPD Power Down Current 50 µA Vcc = 2.0 V to 5.5 V (note 1) 200 KOhm 10 pF 1.8 1 10 4 mA mA mA mA RRST 10 PARAMETER RST Pulldown Resistor CIO Capacitance of I/O Buffer ICC Power Supply Current Freq = 1 MHz Icc op Icc idle Freq = 6 MHz Icc op Icc idle Freq ≥ 12 MHz Icc op = 1.25 Freq (MHz) + 5 mA Icc idle = 0.36 Freq (MHz) + 2.7 mA 50 fc = 1 MHz, Ta = 25_C Vcc = 5.5 V Rev. E (31/08/95) 80C32/80C52 MATRA MHS Absolute Maximum Ratings* Ambient Temperature Under Bias : A = Automotive . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40 to +125 Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . –65 to + 150 Voltage on VCC to VSS . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to + 7 V Voltage on Any Pin to VSS . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W * This value is based on the maximum allowable die temperature and the thermal resistance of the package * Notice Stresses above those listed under “ Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC Parameters TA = –40°C + 125°C ; VSS = 0 V ; VCC = 5 V ± 10 % ; F = 0 to 36 MHz SYMBOL PARAMETER MIN MAX UNIT – 0.5 0.2 Vcc – 0.1 V 0.2 Vcc + 1.4 Vcc + 0.5 V 0.7 Vcc Vcc + 0.5 V TEST CONDITIONS VIL Input Low Voltage VIH Input High Voltage (Except XTAL and RST) VIH1 Input High Voltage (for XTAL and RST) VOL Output Low Voltage (Port 1, 2 and 3) 0.3 0.45 1.0 V V V IOL = 100 µA IOL = 1.6 mA (note 2) IOL = 3.5 mA VOL1 Output Low Voltage (Port 0, ALE, PSEN) 0.3 0.45 1.0 V V V IOL = 200 µA IOL = 3.2 mA (note 2) IOL = 7.0 mA VOH Output High Voltage Port 1, 2 and 3 Vcc – 0.3 V IOH = – 10 µA Vcc – 0.7 V IOH = – 30 µA Vcc – 1.5 V IOH = – 60 µA VCC = 5 V ± 10 % Vcc – 0.3 V IOH = – 200 µΑ Vcc – 0.7 V IOH = – 3.2 mA Vcc – 1.5 V IOH = – 7.0 mA VCC = 5 V ± 10 % VOH1 Output High Voltage (Port 0, ALE, PSEN) IIL Logical 0 Input Current (Ports 1, 2 and 3) – 75 µA Vin = 0.45 V ILI Input leakage Current ±10 µA 0.45 < Vin < Vcc ITL Logical 1 to 0 Transition Current (Ports 1, 2 and 3) – 750 µA Vin = 2.0 V IPD Power Down Current 75 µA Vcc = 2.0 V to 5.5 V (note 1) 200 KOhm 10 pF 1.8 1 10 4 mA mA mA mA RRST RST Pulldown Resistor CIO Capacitance of I/O Buffer ICC Power Supply Current Freq = 1 MHz Icc op Icc idle Freq = 6 MHz Icc op Icc idle Freq ≥ 12 MHz Icc op = 1.25 Freq (MHz) + 5 mA Icc idle = 0.36 Freq (MHz) + 2.7 mA Rev. E (31/08/95) 50 fc = 1 MHz, Ta = 25_C Vcc = 5.5 V 11 80C32/80C52 Absolute Maximum Ratings* Ambient Temperature Under Bias : M = Military . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55 to +125 Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . –65 to + 150 Voltage on VCC to VSS . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to + 7 V Voltage on Any Pin to VSS . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W * This value is based on the maximum allowable die temperature and the thermal resistance of the package MATRA MHS * Notice Stresses at or above those listed under “ Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect device reliability. DC Parameters TA = –55°C + 125°C ; Vss = 0 V ; Vcc = 5 V ± 10 % ; F = 0 to 36 MHz SYMBOL MIN MAX UNIT – 0.5 0.2 Vcc – 0.1 V 0.2 Vcc + 1.4 Vcc + 0.5 V 0.7 Vcc Vcc + 0.5 V TEST CONDITIONS VIL Input Low Voltage VIH Input High Voltage (Except XTAL and RST) VIH1 Input High Voltage (for XTAL and RST) VOL Output Low Voltage (Port 1, 2 and 3) 0.45 V IOL = 1.6 mA (note 2) VOL1 Output Low Voltage (Port 0, ALE, PSEN) 0.45 V IOL = 3.2 mA (note 2) VOH Output High Voltage (Port 1, 2 and 3) 2.4 V IOH = – 60 µA Vcc = 5 V ± 10 % 0.75 Vcc V IOH = – 25 µA 0.9 Vcc V IOH = – 10 µA 2.4 V IOH = – 400 µA Vcc = 5 V ± 10 % 0.75 Vcc V IOH = – 150 µA 0.9 Vcc V IOH = – 40 µA – 75 µA Vin = 0.45 V VOH1 Output High Voltage (Port 0 in External Bus Mode, ALE, PEN) IIL Logical 0 Input Current (Ports 1, 2 and 3) ILI Input leakage Current +/– 10 µA 0.45 < Vin < Vcc ITL Logical 1 to 0 Transition Current (Ports 1, 2 and 3) – 750 µA Vin = 2.0 V IPD Power Down Current 75 µA Vcc = 2.0 V to 5.5 V (note 1) 200 KΩ 10 pF 1.8 1 10 4 mA mA mA mA RRST 12 PARAMETER RST Pulldown Resistor CIO Capacitance of I/O Buffer ICC Power Supply Current Freq = 1 MHz Icc op Icc idle Freq = 6 MHz Icc op Icc idle Freq ≥ 12 MHz Icc op = 1.25 Freq (MHz) + 5 mA Icc idle = 0.36 Freq (MHz) + 2.7 mA 50 fc = 1 MHz, Ta = 25_C Vcc = 5.5 V Rev. E (31/08/95) 80C32/80C52 MATRA MHS * Notice Absolute Maximum Ratings* Ambient Temperature Under Bias : C = Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C I = Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40 to 85°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . –65°C to + 150°C Voltage on VCC to VSS . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to + 7 V Voltage on Any Pin to VSS . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W** ** This value is based on the maximum allowable die temperature and the thermal resistance of the package Stresses at or above those listed under “ Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect device reliability. DC Characteristics TA = 0°C to 70°C ; Vcc = 2.7 V to 5.5 V ; Vss = 0 V ; F = 0 to 16 MHz TA = –40°C to 85°C ; Vcc = 2.7 V to 5.5 V SYMBOL PARAMETER MIN MAX UNIT – 0.5 0.2 VCC – 0.1 V 0.2 VCC + 1.4 VCC + 0.5 V TEST CONDITIONS VIL Input Low Voltage VIH Input High Voltage (Except XTAL and RST) VIH2 Input High Voltage to RST for Reset 0.7 VCC VCC + 0.5 V VIH1 Input High Voltage to XTAL1 0.7 VCC VCC + 0.5 V VPD Power Down Voltage to Vcc in PD Mode 2.0 5.5 V VOL Output Low Voltage (Ports 1, 2, 3) 0.45 V IOL = 0.8 mA (note 2) VOL1 Output Low Voltage Port 0, ALE, PSEN 0.45 V IOL = 1.6 mA (note 2) VOH Output High Voltage Ports 1, 2, 3 0.9 Vcc V IOH = – 10 µA VOH1 Output High Voltage (Port 0 in External Bus Mode), ALE, PSEN 0.9 Vcc V IOH = – 40 µA IIL Logical 0 Input Current Ports 1, 2, 3 – 50 µA Vin = 0.45 V ILI Input Leakage Current ± 10 µA 0.45 < Vin < VCC ITL Logical 1 to 0 Transition Current (Ports 1, 2, 3) – 650 µA Vin = 2.0 V IPD Power Down Current 50 µA VCC = 2.0 V to 5.5 V (note 1) 200 kΩ 10 pF RRST CIO RST Pulldown Resistor 50 Capacitance of I/O Buffer fc = 1 MHz, TA = 25_C Maximum Icc (mA) OPERATING (NOTE 1) IDLE (NOTE 1) FREQUENCY/Vcc 2.7 V 3V 3.3 V 5.5 V 2.7 V 3V 3.3 V 5.5 V 1 MHz 0.8 mA 1 mA 1.1 mA 1.8 mA 400 µA 500 µA 600 µA 1 mA 6 MHz 4 mA 5 mA 6 mA 10 mA 1.5 mA 1.7 mA 2 mA 4 mA 12 MHz 8 mA 10 mA 12 mA 2.5 mA 3 mA 3.5 mA 16 MHz 10 mA 12 mA 14 mA 3 mA 3.8 mA 4.5 mA Freq > 12 MHz (Vcc = 5.5 V) Rev. E (31/08/95) Icc (mA) = 1.25 × Freq (MHz) + 5 Icc Idle (mA) = 0.36 × Freq (MHz) + 2.7 13 80C32/80C52 Note 1 : ICC is measured with all output pins disconnected ; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + .5 V, VIH = VCC –.5 V ; XTAL2 N.C. ; EA = RST = Port 0 = VCC. ICC would be slighty higher if a crystal oscillator used. MATRA MHS Figure 9. ICC Test Condition, Idle Mode. All other pins are disconnected. Idle ICC is measured with all output pins disconnected ; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 5 V, VIH = VCC –.5 V ; XTAL2 N.C ; Port 0 = VCC ; EA = RST = VSS. Power Down ICC is measured with all output pins disconnected ; EA = PORT 0 = VCC ; XTAL2 N.C. ; RST = VSS. Note 2 : Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLS of ALE and Ports 1 and 3. The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operations. In the worst cases (capacitive loading 100 pF), the noise pulse on the ALE line may exceed 0.45 V may exceed 0,45 V with maxi VOL peak 0.6 V. A Schmitt Trigger use is not necessary. Figure 10. ICC Test Condition, Active Mode. All other pins are disconnected. Figure 11. ICC Test Condition, Power Down Mode. All other pins are disconnected. Figure 12. Clock Signal Waveform for ICC Tests in Active and Idle Modes. TCLCH = TCHCL = 5 ns. 14 Rev. E (31/08/95) 80C32/80C52 MATRA MHS Explanation of the AC Symbol Each timing symbol has 5 characters. The first character is always a “T” (stands for time). The other characters, depending on their positions, stand for the name of a signal or the logical status of that signal. The following is a list of all the characters and what they stand for. A : Address. C : Clock. D : Input data. H : Logic level HIGH I : Instruction (program memory contents). L : Logic level LOW, or ALE. P : PSEN. Example : TAVLL = Time for Address Valid to ALE low. TLLPL = Time for ALE low to PSEN low. Q : Output data. R : READ signal. T : Time. V : Valid. W : WRITE signal. X : No longer a valid logic level. Z : Float. AC Parameters TA = 0 to + 70°C ; Vss = 0 V ; Vcc = 5 V ± 10 % ; F = 0 to 44 MHz TA = 0 to +70°C ; Vss = 0 V ; 2.7 V < Vcc < 5.5 V ; F = 0 to 16 MHz TA = –40° to + 85°C ; Vss = 0 V ; 2.7 V < Vcc < 5.5 V ; F = 0 to 16 MHz TA = –55° + 125°C ; Vss = 0 V ; Vcc = 5 V ± 10 % ; F = 0 to 36 MHz (Load Capacitance for PORT 0, ALE and PSEN = 100 pF ; Load Capacitance for all other outputs = 80 pF) External Program Memory Characteristics (values in ns) 16 MHz SYMBOL PARAMETER 20 MHz 25 MHz 30 MHz 36 MHz 40 MHz 42 MHz 44 MHz min max min max min max min max min max min max min max min max TLHLL ALE Pulse Width 110 90 70 60 50 40 35 30 TAVLL Address valid to ALE 40 30 20 15 10 9 8 7 TLLAX Address Hold After ALE 35 TLLIV ALE to valid instr in 35 185 35 170 35 130 35 100 30 80 25 70 17 65 65 TLLPL ALE to PSEN 45 40 30 25 20 15 13 12 TPLPH PSEN pulse Width 165 130 100 80 75 65 60 54 TPLIV PSEN to valid instr in TPXIX Input instr Hold After PSEN 125 0 110 0 50 85 0 TAVIV Address to Valid instr in 230 210 170 130 90 80 75 70 TPLAZ PSEN low to Address Float 10 10 8 6 5 5 5 5 30 20 35 0 PSEN to Address Valid 35 25 40 0 Input instr Float After PSEN 40 30 45 0 TPXIZ 50 35 50 0 TPXAV 55 45 65 0 25 15 20 10 15 External Program Memory Read Cycle Rev. E (31/08/95) 15 80C32/80C52 MATRA MHS External Data Memory Characteristics (values in ns) 16 MHz SYMBOL PARAMETER 20 MHz 25 MHz 30 MHz 36 MHz 40 MHz 42 MHz 44 MHz min max min max min max min max min max min max min max min max TRLRH RD pulse Width 340 270 210 180 120 100 90 80 TWLWH WR pulse Width 340 270 210 180 120 100 90 80 85 TLLAX Address Hold After ALE TRLDV RD to Valid in 85 TRHDX Data hold after RD TRHDZ Data float after RD 90 90 80 70 50 45 40 35 TLLDV ALE to Valid Data In 435 370 350 235 170 150 140 130 240 0 TAVDV Address to Valid Data IN TLLWL ALE to WR or RD 150 70 210 0 480 250 0 400 135 55 175 170 0 300 120 35 135 130 0 260 90 30 110 115 0 190 70 25 90 100 0 180 60 25 80 95 70 0 175 55 90 170 50 TAVWL Address to WR or RD 180 180 140 115 75 65 60 55 TQVWX Data valid to WR transition 35 35 30 20 15 10 8 6 TQVWH Data Setup to WR transition 380 325 250 215 170 160 150 140 TWHQX Data Hold after WR 40 TRLAZ RD low to Address Float TWHLH RD or WR high to ALE high 35 0 35 90 30 0 35 60 20 0 25 45 15 0 20 40 10 0 20 40 8 0 15 35 6 0 13 85 33 0 13 33 External Data Memory Write Cycle External Data Memory Read Cycle 16 Rev. E (31/08/95) 80C32/80C52 MATRA MHS Serial Port Timing – Shift Register Mode (values in ns) 16 MHz SYMBOL PARAMETER 20 MHz 25 MHz 30 MHz 36 MHz 40 MHz 42 MHz 44 MHz min max min max min max min max min max min max min max min max TXLXL Serial Port Clock Cycle Time 750 600 480 400 330 250 230 227 TQVXH Output Data Setup to Clock Rising Edge 563 480 380 300 220 170 150 140 TXHQX Output Data Hold after Clock Rising Edge 63 90 65 50 45 35 30 25 TXHDX Input Data Hold after Clock Rising Edge 0 0 0 0 0 0 0 0 TXHDV Clock Rising Edge to Input Data Valid 563 450 350 300 250 200 180 160 Shift Register Timing Waveforms Rev. E (31/08/95) 17 80C32/80C52 MATRA MHS External Clock Drive Characteristics (XTAL1) SYMBOL PARAMETER FCLCL Oscillator Frequency TCLCL Oscillator period TCHCX MIN MAX UNIT 44 MHz 22.7 ns High Time 5 ns TCLCX Low Time 5 ns TCLCH Rise Time 5 ns TCHCL Fall Time 5 ns External Clock Drive Waveforms AC Testing Input/Output Waveforms AC inputs during testing are driven at Vcc – 0.5 for a logic “1” and 0.45 V for a logic “0”. Timing measurements are made at VIH min for a logic “1” and VIL max for a logic “0”. Float Waveforms For timing purposes as port pin is no longer floating when a 100 mV change from load voltage occurs and begins to float when a 100 mV change from the loaded VOH/VOL level occurs. Iol/IoH ≥ ± 20 mA. 18 Rev. E (31/08/95) MATRA MHS 80C32/80C52 Clock Waveforms This diagram indicates when signals are clocked internally. The time it takes the signals to propagate to the pins, however, ranges from 25 to 125 ns. This propagation delay is dependent on variables such as temperature and pin loading. Propagation also varies from output to output and component. Typically though (TA = 25°C fully loaded) RD and WR propagation delays are approximately 50 ns. The other signals are typically 85 ns. Propagation delays are incorporated in the AC specifications. Rev. E (31/08/95) 19 80C32/80C52 MATRA MHS Ordering Information I Temperature Range blank : Commercial I : Industrial A : Automotive M : Military Part Number 80C52 Rom 8 K × 8 80C32 External ROM 80C52C Secret ROM version 80C52T Secret Tag version Package Type (1) F1, F2 : Quad Flat Pack (2) P : Plastic DIL S : PLCC V : V Quad Flat Pack (1.4 mm) T : T Quad Flat Pack (1 mm) 80C52C –12 –16 –20 –25 –30 –36 –40 –42 –44 –L16 : 12 MHz version : 16 MHz version : 20 MHz version : 25 MHz version : 30 MHz version : 36 MHz version : 40 MHz version (3) : 42 MHz version (3) : 44 MHz version (3) : Low Power (Vcc : 2.7-5.5 V Freq : 0-16 MHz) Customer Rom Code R : Tape and Reel D : Dry Pack (1) Ceramic of multi-layer packages : contact TEMIC sales office. (2) See mechanical outlines available on Databook or on request. (3) Only for 80C32 at commercial range. 20 Rev. E (31/08/95)