INNOVASIC AM186ES

IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
®
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 1 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Copyright
Data Sheet
November 15, 2011
2011 by Innovasic Semiconductor, Inc.
Published by Innovasic Semiconductor, Inc.
3737 Princeton Drive NE, Suite 130, Albuquerque, NM 87107
AMD, Am186, and Am188 are trademarks of Advanced Micro Devices, Inc.
MILES™ is a trademark of Innovasic Semiconductor, Inc.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 2 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
TABLE OF CONTENTS
List of Figures ..................................................................................................................................9
List of Tables .................................................................................................................................10
Conventions ...................................................................................................................................13
Acronyms and Abbreviations ........................................................................................................14
1.
Introduction...........................................................................................................................15
1.1 General Description.....................................................................................................15
1.2 Features .......................................................................................................................15
2.
Packaging, Pin Descriptions, and Physical Dimensions .......................................................16
2.1 Packages and Pinouts ..................................................................................................16
2.1.1 IA186ES TQFP Package ................................................................................17
2.1.2 IA188ES TQFP Package ................................................................................20
2.1.3 TQFP Physical Dimensions ............................................................................23
2.1.4 IA186ES PQFP Package.................................................................................24
2.1.5 IA188ES PQFP Package.................................................................................27
2.1.6 PQFP Physical Dimensions ............................................................................30
2.2 Pin Descriptions ..........................................................................................................31
2.2.1 a19/pio9, a18/pio8, a17/pio7, a16–a0—Address Bus (synchronous
outputs with tristate) .......................................................................................31
2.2.2 ad15–ad8 (IA186ES)—Address/Data Bus (level-sensitive
synchronous inouts with tristate) ....................................................................31
2.2.3 ao15–ao8 (IA188ES)—Address Bus (level-sensitive synchronous
outputs with tristate) .......................................................................................31
2.2.4 ad7–ad0—Address/Data Bus (level-sensitive synchronous inouts with
tristate) ............................................................................................................31
2.2.5 ale—Address Latch Enable (synchronous output) .........................................32
2.2.6 ardy—Asynchronous Ready (level-sensitive asynchronous input) ................32
2.2.7 bhe_n/aden_n (IA186ES only)—Bus High Enable (synchronous
output with tristate)/Address Enable (input with internal pullup) ..................32
2.2.8 clkouta—Clock Output A (synchronous output) ............................................33
2.2.9 clkoutb—Clock Output B (synchronous output) ............................................33
2.2.10 cts0_n/enrx0_n/pio21—Clear-to-Send 0/Enable-Receive-Request 0
(both are asynchronous inputs) .......................................................................33
2.2.11 den_n/ds_n/pio5—Data Enable /Data Strobe (both are synchronous
outputs with tristate) .......................................................................................34
2.2.12 drq0/int5/pio12—DMA Request 0 (synchronous level-sensitive
input)/Maskable Interrupt Request 5 (asynchronous edge-triggered
input) ...............................................................................................................34
2.2.13 drq1/int6/pio13—DMA Request 1 (synchronous level-sensitive
input)/Maskable Interrupt Request 6 (asynchronous edge-triggered
input) ...............................................................................................................34
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 3 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
2.2.14 dt/r_n/pio4—Data Transmit or Receive (synchronous output with
tristate) ............................................................................................................34
2.2.15 gnd—Ground ..................................................................................................35
2.2.16 hlda—Bus Hold Acknowledge (synchronous output) ....................................35
2.2.17 int0—Maskable Interrupt Request 0 (asynchronous input) ............................35
2.2.18 int1/select_n—Maskable Interrupt Request 1/Slave Select (both are
asynchronous inputs) ......................................................................................35
2.2.19 int2/inta0_n/pwd/pio31—Maskable Interrupt Request 2
(asynchronous input)/Interrupt Acknowledge 0 (synchronous
output)/Pulse Width Demodulator (Schmitt trigger input) .............................36
2.2.20 int3/inta1_n/irq—Maskable Interrupt Request 3 (asynchronous
input)/Interrupt Acknowledge 1 (synchronous output)/Interrupt
Acknowledge (synchronous output) ...............................................................36
2.2.21 int4/pio30—Maskable Interrupt Request 4 (asynchronous input)..................37
2.2.22 lcs_n/once0_n—Lower Memory Chip Select (synchronous output
with internal pullup)/ONCE Mode Request (input) .......................................37
2.2.23 mcs0_n/pio14—Midrange Memory Chip Select (synchronous output
with internal pullup) .......................................................................................37
2.2.24 mcs2_n–mcs1_n (pio24–pio 15)—Midrange Memory Chip Selects
(synchronous outputs with internal pullup) ....................................................37
2.2.25 mcs3_n/rfsh_n/pio25—Midrange Memory Chip Select (synchronous
outputs with internal pullup)/Automatic Refresh (synchronous output) ........38
2.2.26 nmi—Nonmaskable Interrupt (synchronous edge-sensitive input) ................38
2.2.27 pcs1_n–pcs0_n (pio17–pio16)—Peripheral Chip Selects 1–0
(synchronous outputs) .....................................................................................38
2.2.28 pcs2_n/cts1_n/enrx1_n/pio18—Peripheral Chip Select 2
(synchronous output)/Clear-to-Send 1 (asynchronous input)/EnableReceiver-Request 1 (asynchronous input) ......................................................39
2.2.29 pcs3_n/rts1_n/rtr1_n/pio18—Peripheral Chip Select 3 (synchronous
output)/Ready-to-Send 1 (asynchronous output)/Ready-to-Receive 1
(asynchronous input) ......................................................................................39
2.2.30 pcs5_n/A1/pio3—Peripheral Chip Select 5 (synchronous
output)/Latched Address Bit [1] (synchronous output) ..................................40
2.2.31 pcs6_n/A2/pio2—Peripheral Chip Select 6 (synchronous
output)/Latched Address Bit [2] (synchronous output) ..................................40
2.2.32 pio31–pio0—Programmable I/O Pins (asynchronous input/output
open-drain) ......................................................................................................40
2.2.33 rd_n—Read strobe (synchronous output with tristate) ...................................40
2.2.34 res_n—Reset (asynchronous level-sensitive input) ........................................40
2.2.35 rfsh2_n/aden_n (IA188ES only)—Refresh 2 (synchronous output
with tristate)/Address Enable (input with internal pullup) .............................41
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 4 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
3.
4.
Data Sheet
November 15, 2011
2.2.36 rts0_n/rtr0_n/pio20—Ready-to-Send 0 (asynchronous output)/Readyto-Receive 0 (asynchronous input) .................................................................41
2.2.37 rxd0_n/pio23—Receive Data 0 (asynchronous input) ...................................41
2.2.38 rxd1_n/pio28—Receive Data 1 (asynchronous input) ...................................41
2.2.39 s2_n–s0_n—Bus Cycle Status (synchronous outputs with tristate) ...............41
2.2.40 s6/lock_n/clkdiv2_n/pio29—Bus Cycle Status Bit [6] (synchronous
output)/Bus Lock (synchronous output)/Clock Divide by 2 (input with
internal pullup)................................................................................................42
2.2.41 srdy/pio6—Synchronous Ready (synchronous level-sensitive input) ............42
2.2.42 tmrin0/pio11—Timer Input 0 (synchronous edge-sensitive input) ................42
2.2.43 tmrin1/pio0—Timer Input 1 (synchronous edge-sensitive input) ..................43
2.2.44 tmrout0/pio10—Timer Output 0 (synchronous output) .................................43
2.2.45 tmrout1/pio1—Timer Output 1 (synchronous output) ...................................43
2.2.46 txd0/pio22—Transmit Data 0 (asynchronous output) ....................................43
2.2.47 txd1/pio27—Transmit Data 1 (asynchronous output) ....................................43
2.2.48 ucs_n/once1_n—Upper Memory Chip Select (synchronous
output)/ONCE Mode Request 1 (input with internal pullup) .........................43
2.2.49 uzi_n/pio26—Upper Zero Indicate (synchronous output) ..............................44
2.2.50 vcc—Power Supply (input)..............................................................................44
2.2.51 whb_n (IA186ES only)—Write High Byte (synchronous output with
tristate) ............................................................................................................44
2.2.52 wlb_n/wb_n—Write Low Byte (IA186ES only) (synchronous output
with tristate)/Write Byte (IA188ES only) (synchronous output with
tristate) ............................................................................................................44
2.2.53 wr_n—Write Strobe (synchronous output) ....................................................44
2.2.54 x1—Crystal Input ...........................................................................................44
2.2.55 x2—Crystal Input ...........................................................................................44
2.3 Pins Used by Emulators ..............................................................................................45
Maximum Ratings, Thermal Characteristics, and DC Parameters .......................................45
Device Architecture ..............................................................................................................47
4.1 Bus Interface and Control ...........................................................................................47
4.2 Clock and Power Management ...................................................................................49
4.3 System Clocks .............................................................................................................49
4.4 Power-Save Mode .......................................................................................................50
4.5 Initialization and Reset ................................................................................................50
4.6 Reset Configuration Register ......................................................................................50
4.7 Chip Selects .................................................................................................................50
4.8 Chip-Select Timing .....................................................................................................50
4.9 Ready- and Wait-State Programming..........................................................................51
4.10 Chip-Select Overlap ....................................................................................................51
4.11 Upper-Memory Chip Select ........................................................................................52
4.12 Low-Memory Chip Select ...........................................................................................52
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 5 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
5.
Data Sheet
November 15, 2011
4.13 Midrange-Memory Chip Selects .................................................................................52
4.14 Peripheral Chip Selects ...............................................................................................53
4.15 Refresh Control ...........................................................................................................53
4.16 Interrupt Control ..........................................................................................................53
4.17 Interrupt Types ............................................................................................................54
4.18 Timer Control ..............................................................................................................55
4.19 Watchdog Timer ..........................................................................................................56
4.20 Direct Memory Access ................................................................................................57
4.21 DMA Operation...........................................................................................................57
4.22 DMA Channel Control Registers ................................................................................58
4.23 DMA Priority ..............................................................................................................59
4.24 Pulse Width Demodulation .........................................................................................59
4.25 Asynchronous Serial Ports ..........................................................................................60
4.26 Programmable I/O .......................................................................................................60
Peripheral Architecture .........................................................................................................62
5.1 Control and Registers ..................................................................................................62
5.1.1 RELREG (0feh) ..............................................................................................64
5.1.2 RESCON (0f6h)..............................................................................................64
5.1.3 PRL (0f4h) ......................................................................................................64
5.1.4 AUXCON (0f2h) ............................................................................................65
5.1.5 SYSCON (0f0h)..............................................................................................66
5.1.6 WDTCON (0e6h) ...........................................................................................67
5.1.7 EDRAM (0e4h) ..............................................................................................68
5.1.8 CDRAM (0e2h) ..............................................................................................69
5.1.9 MDRAM (0e0h) .............................................................................................69
5.1.10 D1CON (0dah) and D0CON (0cah) ...............................................................69
5.1.11 D1TC (0d8h) and D0TC (0c8h) .....................................................................71
5.1.12 D1DSTH (0d6h) and D0DSTH (0c6h) ...........................................................72
5.1.13 DIDSTL (0d4h) and D0DSTL (0c4h) ............................................................72
5.1.14 D1SRCH (0d2h) and D0SRCH (0c2h) ...........................................................72
5.1.15 D1SRCL (0d0h) and D0SRCL (0c0h) ............................................................73
5.1.16 MPCS (0a8h) ..................................................................................................73
5.1.17 MMCS (0a6h) .................................................................................................75
5.1.18 PACS (0a4h) ...................................................................................................76
5.1.19 LMCS (0a2h) ..................................................................................................77
5.1.20 UMCS (0a0h)..................................................................................................79
5.1.21 SP0BAUD (088h) ...........................................................................................80
5.1.22 SP1BAUD (018h) ...........................................................................................80
5.1.23 SP0RD (086h) and SP1RD (016h) .................................................................81
5.1.24 SP0TD (084h) and SP1TD (014h) ..................................................................82
5.1.25 SP0STS (082h) and SP1STS (012h)...............................................................82
5.1.26 SP0CT (080h) and SP1CT (010h) ..................................................................84
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 6 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
5.1.27
5.1.28
5.1.29
5.1.30
5.1.31
5.1.32
6.
7.
PDATA1 (07ah) and PDATA0 (074h) ...........................................................87
PDIR1 (078h) and PDIR0 (072h) ...................................................................89
PMODE1 (076h) and PMODE0 (070h) .........................................................90
T1CON (05eh) and T0CON (056h) ................................................................91
T2CON (066h) ................................................................................................92
T2COMPA (062h), T1COMPB (05ch), T1COMPA (05ah),
T0COMPB (054h), and T0COMPA (052h) ...................................................93
5.1.33 T2CNT (060h), T1CNT (058h), and T0CNT (050h) .....................................93
5.1.34 SP0CON (044h) and SP1CON (042h) (Master Mode) ..................................94
5.1.35 I4CON (040h) (Master Mode) ........................................................................95
5.1.36 I3CON (03eh) and I2CON (03ch) (Master Mode) .........................................95
5.1.37 I1CON (03ah) and I0CON (038h) (Master Mode) .........................................96
5.1.38 TCUCON (032h) (Master Mode) ...................................................................97
5.1.39 T2INTCON (03ah), T1INTCON (038h), and T0INTCON (032h)
(Slave Mode) ..................................................................................................97
5.1.40 DMA1CON/INT6CON (036h) and DMA0CON/INT5CON (034h)
(Master Mode) ................................................................................................98
5.1.41 DMA1CON/INT6 (036h) and DMA0CON/INT5 (034h) (Slave
Mode) ..............................................................................................................98
5.1.42 INTSTS (030h) (Master Mode) ......................................................................99
5.1.43 INTSTS (030h) (Slave Mode) ........................................................................99
5.1.44 REQST (02eh) (Master Mode) .....................................................................100
5.1.45 REQST (02eh) (Slave Mode) .......................................................................101
5.1.46 INSERV (02ch) (Master Mode) ...................................................................101
5.1.47 INSERV (02ch) (Slave Mode)......................................................................102
5.1.48 PRIMSK (02ah) (Master and Slave Mode) ..................................................103
5.1.49 IMASK (028h) (Master Mode) .....................................................................103
5.1.50 IMASK (028h) (Slave Mode) .......................................................................104
5.1.51 POLLST (026h) (Master Mode) ...................................................................105
5.1.52 POLL (024h) (Master Mode)........................................................................105
5.1.53 EOI (022h) End-Of-Interrupt Register (Master Mode) ................................106
5.1.54 EOI (022h) Specific End-Of-Interrupt Register (Slave Mode) ....................106
5.1.55 INTVEC (020h) Interrupt Vector Register (Slave Mode) ............................107
5.2 Reference Documents ...............................................................................................107
AC Specifications ...............................................................................................................108
Instruction Set Summary Table ..........................................................................................134
7.1 Key to Abbreviations Used in Instruction Set Summary Table ................................144
7.1.1 Operand Address Byte ..................................................................................144
7.1.2 Modifier Field ...............................................................................................144
7.1.3 Auxiliary Field ..............................................................................................144
7.1.4 r/m Field........................................................................................................145
7.1.5 Displacement ................................................................................................145
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 7 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
8.
9.
10.
11.
Data Sheet
November 15, 2011
7.1.6 Immediate Bytes ...........................................................................................145
7.1.7 Segment Override Prefix ..............................................................................145
7.1.8 Segment Register ..........................................................................................145
7.2 Explanation of Notation Used in Instruction Set Summary Table ............................146
7.2.1 Opcode ..........................................................................................................146
7.2.2 Flags Affected After Instruction ...................................................................147
Innovasic/AMD Part Number Cross-Reference Tables......................................................148
Errata...................................................................................................................................150
9.1 Errata Summary.........................................................................................................150
9.2 Errata Detail ..............................................................................................................150
Revision History .................................................................................................................153
For Additional Information.................................................................................................154
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 8 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
LIST OF FIGURES
Figure 1. IA186ES TQFP Package Diagram ................................................................................17
Figure 2. IA188ES TQFP Package Diagram ................................................................................20
Figure 3. TQFP Package Dimensions ...........................................................................................23
Figure 4. IA186ES PQFP Package Diagram ................................................................................24
Figure 5. IA188ES PQFP Package Diagram ................................................................................27
Figure 6. PQFP Package Dimensions ...........................................................................................30
Figure 7. Functional Block Diagram ............................................................................................48
Figure 8. Crystal Configuration ....................................................................................................49
Figure 9. Organization of Clock ...................................................................................................49
Figure 10. DMA Unit ....................................................................................................................58
Figure 11. Typical Waveform at the int2/int0_n/pwd pin ............................................................59
Figure 12. Read Cycle.................................................................................................................113
Figure 13. Multiple Read Cycles ................................................................................................114
Figure 14. Write Cycle ................................................................................................................116
Figure 15. Multiple Write Cycles ...............................................................................................117
Figure 16. PSRAM Read Cycle ..................................................................................................119
Figure 17. PSRAM Write Cycle .................................................................................................121
Figure 18. PSRAM Refresh Cycle ..............................................................................................123
Figure 19. Interrupt Acknowledge Cycle....................................................................................124
Figure 20. Software Halt Cycle ..................................................................................................126
Figure 21. Clock—Active Mode.................................................................................................128
Figure 22. Clock—Power-Save Mode ........................................................................................128
Figure 23. srdy—Synchronous Ready ........................................................................................129
Figure 24. ardy—Asynchronous Ready......................................................................................130
Figure 25. Peripherals .................................................................................................................130
Figure 26. Reset 1 .......................................................................................................................131
Figure 27. Reset 2 .......................................................................................................................131
Figure 28. Bus Hold Entering .....................................................................................................132
Figure 29. Bus Hold Leaving ......................................................................................................132
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 9 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
LIST OF TABLES
Table 1. IA186ES TQFP Numeric Pin Listing .............................................................................18
Table 2. IA186ES TQFP Alphabetic Pin Listing..........................................................................19
Table 3. IA188ES TQFP Numeric Pin Listing .............................................................................21
Table 4. IA188ES TQFP Alphabetic Pin Listing..........................................................................22
Table 5. IA186ES PQFP Numeric Pin Listing .............................................................................25
Table 6. IA186ES PQFP Alphabetic Pin Listing ..........................................................................26
Table 7. IA188ES PQFP Numeric Pin Listing .............................................................................28
Table 8. IA188ES PQFP Alphabetic Pin Listing ..........................................................................29
Table 9. Bus Cycle Types for bhe_n and ad0 ...............................................................................32
Table 10. Bus Cycle Types for s2_n, s1_n, and s0_n ...................................................................42
Table 11. IA186ES and IA188ES Absolute Maximum Ratings...................................................45
Table 12. IA186ES and IA188ES Thermal Characteristics..........................................................45
Table 13. DC Characteristics Over Commercial Operating Ranges .............................................46
Table 14. Interrupt Types ..............................................................................................................54
Table 15. Default Status of PIO Pins at Reset ..............................................................................61
Table 16. Peripheral Control Registers .........................................................................................63
Table 17. Peripheral Control Block Relocation Register..............................................................64
Table 18. Reset Configuration Register ........................................................................................64
Table 19. Processor Release Level Register .................................................................................65
Table 20. Auxiliary Configuration Register .................................................................................65
Table 21. System Configuration Register .....................................................................................66
Table 22. Watchdog Timer Control Register ................................................................................67
Table 23. Enable Dynamic RAM Refresh Control Register.........................................................68
Table 24. Count for Dynamic RAM Refresh Control Register ....................................................69
Table 25. Memory Partition for Dynamic RAM Refresh Control Register .................................69
Table 26. DMA Control Registers ................................................................................................69
Table 27. DMA Transfer Count Registers ....................................................................................71
Table 28. DMA Destination Address High Register ....................................................................72
Table 29. DMA Destination Address Low Register .....................................................................72
Table 30. DMA Source Address High Register............................................................................73
Table 31. DMA Source Address Low Register ............................................................................73
Table 32. MCS and PCS Auxiliary Register ................................................................................74
Table 33. Midrange Memory Chip Select Register ......................................................................75
Table 34. Peripheral Chip Select Register ....................................................................................76
Table 35. Low-Memory Chip Select Register ..............................................................................78
Table 36. Upper-Memory Chip Select Register ...........................................................................79
Table 37. Baud Rates ....................................................................................................................81
Table 38. Serial Port Baud Rate Divisor Registers .......................................................................81
Table 39. Serial Port Receive Registers ........................................................................................82
Table 40. Serial Port Transmit Registers ......................................................................................82
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 10 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Table 41.
Table 42.
Table 43.
Table 44.
Table 45.
Table 46.
Table 47.
Table 48.
Table 49.
Table 50.
Table 51.
Table 52.
Table 53.
Table 54.
Table 55.
Table 56.
Table 57.
Table 58.
Table 59.
Table 60.
Table 61.
Table 62.
Table 63.
Table 64.
Table 65.
Table 66.
Table 67.
Table 68.
Table 69.
Table 70.
Table 71.
Table 72.
Table 73.
Table 74.
Table 75.
Table 76.
Table 77.
Table 78.
Table 79.
Table 80.
Table 81.
Table 82.
Data Sheet
November 15, 2011
Serial Port Status Register ............................................................................................83
Serial Port Control Registers ........................................................................................84
PIO Pin Assignments ....................................................................................................88
PDATA 0 ......................................................................................................................89
PDATA 1 ......................................................................................................................89
PIO Mode and PIO Direction Settings .........................................................................89
PDIR0 ...........................................................................................................................90
PDIR1 ...........................................................................................................................90
PMODE0 ......................................................................................................................90
PMODE1 ......................................................................................................................90
Timer0 and Timer1 Mode and Control Registers .........................................................91
Timer2 Mode and Control Registers ............................................................................92
Timer Maxcount Compare Registers ............................................................................93
Timer Count Registers ..................................................................................................94
Serial Port Interrupt Control Registers .........................................................................94
INT4 Control Register ..................................................................................................95
INT2/INT3 Control Register ........................................................................................96
INT0/INT1 Control Register ........................................................................................96
Timer Control Unit Interrupt Control Register .............................................................97
Timer Interrupt Control Register ..................................................................................97
DMA and Interrupt Control Register (Master Mode) ...................................................98
DMA and Interrupt Control Register (Slave Mode) .....................................................98
Interrupt Status Register (Master Mode) ......................................................................99
Interrupt Status Register (Slave Mode) ........................................................................99
Interrupt Request Register (Master Mode) .................................................................100
Interrupt Request Register (Slave Mode) ...................................................................101
In-Service Register (Master Mode) ............................................................................102
In-Service Register (Slave Mode)...............................................................................102
Priority Mask Register ................................................................................................103
Interrupt MASK Register (Master Mode) ..................................................................104
Interrupt MASK Register (Slave Mode) .....................................................................104
POLL Status Register .................................................................................................105
Poll Register ................................................................................................................106
End-Of-Interrupt Register ...........................................................................................106
Specific End-Of-Interrupt Register .............................................................................106
Interrupt Vector Register ............................................................................................107
Alphabetic Key to Waveform Parameters ..................................................................108
Numeric Key to Waveform Parameters ......................................................................110
Read Cycle Timing .....................................................................................................115
Write Cycle Timing ....................................................................................................118
PSRAM Read Cycle Timing.......................................................................................120
PSRAM Write Cycle Timing ......................................................................................122
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 11 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Table 83.
Table 84.
Table 85.
Table 86.
Table 87.
Table 88.
Table 89.
Table 90.
Table 91.
Table 92.
Table 93.
Data Sheet
November 15, 2011
PSRAM Refresh Cycle Timing ..................................................................................123
Interrupt Acknowledge Cycle Timing ........................................................................125
Software Halt Cycle Timing .......................................................................................127
Clock Timing ..............................................................................................................129
Ready and Peripheral Timing .....................................................................................131
Reset and Bus Hold Timing ........................................................................................133
Instruction Set Summary ............................................................................................134
Innovasic/AMD Part Number Cross-Reference for the TQFP ...................................148
Innovasic/AMD Part Number Cross-Reference for the PQFP ...................................149
Summary of Errata ......................................................................................................150
Revision History .........................................................................................................153
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 12 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
CONVENTIONS
Arial Bold
Designates headings, figure captions, and table captions.
Blue
Designates hyperlinks (PDF copy only).
Italics
Designates emphasis or caution related to nearby information. Italics is also
used to designate variables, refer to related documents, and to differentiate
terms from other common words (e.g., “During refresh cycles, the a and ad
busses may not have the same address during the address phase of the ad bus
cycle.”).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 13 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
ACRONYMS AND ABBREVIATIONS
AMD
BIC
CDRAM
CSC
DA
DMA
EOI
INSERV
ISR
LMCS
MC
MDRAM
MILES™
MMCS
NMI
PCB
PIO
PLL
POR
PQFP
PSRAM
RCU
RoHS
SFNM
SYSCON
TQFP
UART
UMCS
WDT
Advanced Micro Devices
Bus Interface and Control
Count for Dynamic RAM
Chip Selects and Control
Disable Address
Direct Memory Access
End of Interrupt
In-Service
Interrupt Service Routine
Low-Memory Chip Select
Maximum Count
Memory Partition for Dynamic RAM
Managed IC Lifetime Extension System
Midrange Memory Chip Select
nonmaskable interrupt
peripheral control block
programmable I/O
phase-lock-loop
power-on reset
Plastic Quad Flat Package
Pseudo-Static RAM
Refresh Control Unit
Restriction of Hazardous Substances
Special Fully Nested mode
System Configuration Register
Thin Quad Flat Package
Universal Asynchronous Receiver-Transmitter
Upper Memory Chip Select
Watchdog Timer
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 14 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
1.
Data Sheet
November 15, 2011
Introduction
The IA186ES/IA188ES is a form, fit, and function replacement for the original Advanced Micro
Devices (AMD ) Am186ES/188ES family of microcontrollers. Innovasic produces replacement
ICs using its MILES™, or Managed IC Lifetime Extension System, cloning technology that
produces replacement ICs far more complex than “emulation” while ensuring they are
compatible with the original IC. MILES captures the design of a clone so it can be produced
even as silicon technology advances. MILES also verifies the clone against the original IC so
that even the “undocumented features” are duplicated.
1.1
General Description
The IA186ES/IA188ES family of microcontrollers replaces obsolete AMD Am186ES/188ES
devices, allowing customers to retain existing board designs, software compilers/assemblers, and
emulation tools and thus avoid expensive redesign efforts.
The IA186ES/IA188ES microcontrollers are an upgrade for the 80C186/188 microcontroller
designs, with integrated peripherals to provide increased functionality and reduce system costs.
The Innovasic devices are designed to satisfy requirements of embedded products designed for
telecommunications, office automation/storage, and industrial controls.
1.2
Features
Pin-for-pin compatible with AMD Am186ES/188ES devices
All features are retained, including:
– A phase-lock loop (PLL) allowing same crystal/system clock frequency
– An 8086/8088 instruction set with additional 186 instruction set extensions
– A programmable interrupt controller
– Two Direct Memory Access (DMA) channels
– Three 16-bit timers
– A wait-state generator and programmable chip select logic
– A dedicated watchdog timer (WDT)
– Two independent asynchronous serial ports (UARTs)
o DMA capability
o Hardware flow control
o 7-, 8-, or 9-bit data capability
–
–
Pulse width demodulator feature
Up to 32 programmable I/O (PIO) pins
A pseudo-static/dynamic RAM controller
A fully static CMOS design
40-MHz operation at industrial operating conditions
+5-VDC power supply
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 15 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
2.
Data Sheet
November 15, 2011
Packaging, Pin Descriptions, and Physical Dimensions
Information on the packages and pin descriptions for the IA186ES and the IA188ES is provided
separately. Refer to sections, figures, and tables for information on the device of interest.
2.1
Packages and Pinouts
The Innovasic Semiconductor IA186ES and IA188ES microcontroller is available in the
following packages:
100-Pin Thin Quad Flat Package (TQFP), equivalent to original SQFP package
100-Plastic Quad Flat Package (PQFP), equivalent to original PQFP package
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 16 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
2.1.1
Data Sheet
November 15, 2011
IA186ES TQFP Package
drq0/int5/pio12
drq1/int6/pio13
tmrin0/pio11
tmrout0/pio10
tmrout1/pio1
tmrin1/pio0
res_n
gnd
mcs3_n/rfsh_n/pio25
mcs2_n/pio24
vcc
pcs0_n/pio16
pcs1_n/pio17
gnd
pcs2_n/cts1_n/enrx1_n/pio18
pcs3_n/rts1_n/rtr1_n/pio19
vcc
pcs5_n/a1/pio3
pcs6_n/a2/pio2
lcs_n/once0_n
ucs_n/once1_n
int0
int1/select_n
int2/inta0_n/pwd/pio31
int3/inta1_n/irq
The pinout for the IA186ES TQFP package is as shown in Figure 1. The corresponding pinout is
provided in Tables 1 and 2.
®
IA186ES
TQFP
int4/pio30
mcs1_n/pio15
mcs0_n/pio14
den_n/ds_n/pio5
dt/r_n/pio4
nmi
srdy/pio6
hold
hlda
wlb_n
whb_n
gnd
a0
a1
vcc
a2
a3
a4
a5
a6
a7
a8
a9
a10
a11
rts0_n/rtr0_n/pio20
bhe_n/aden_n
wr_n
rd_n
ale
ardy
s2_n
s1_n
s0_n
gnd
x1
x2
vcc
clkouta
clkoutb
gnd
a19/pio9
a18/pio8
vcc
a17/pio7
a16
a15
a14
a13
a12
ad0
ad8
ad1
ad9
ad2
ad10
ad3
ad11
ad4
ad12
ad5
gnd
ad13
ad6
vcc
ad14
ad7
ad15
s6/lock_n/clkdiv2_n/pio29
uzi_n/pio26
txd1/pio27
rxd1/pio28
cts0_n/enrx0_n/pio21
rxd0/pio23
txd0/pio22
Figure 1. IA186ES TQFP Package Diagram
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 17 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 1. IA186ES TQFP Numeric Pin Listing
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Name
ad0
ad8
ad1
ad9
ad2
ad10
ad3
ad11
ad4
ad12
ad5
gnd
ad13
ad6
vCC
ad14
ad7
ad15
s6/lock_n/clkdiv2_n/pio29
uzi_n/pio26
txd1/pio27
rxd1/pio28
cts0_n/enrx0_n/pio21
rxd0/pio23
txd0/pio22
rts0_n/rtr0_n/pio20
bhe_n/aden_n
wr_n
rd_n
ale
ardy
s2_n
s1_n
s0_n
®
Pin
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Name
gnd
x1
x2
vCC
clkouta
clkoutb
gnd
a19/pio9
a18/pio8
vCC
a17/pio7
a16
a15
a14
a13
a12
a11
a10
a9
a8
a7
a6
a5
a4
a3
a2
vCC
a1
a0
gnd
whb_n
wlb_n
hlda
Pin
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 18 of 154
Name
hold
srdy/pio6
nmi
dt/r_n/pio4
den_n/ds_n/pio5
mcs0_n/pio14
mcs1_n/pio15
int4/pio30
int3/inta1_n/irq
int2/inta0_n/pwd/pio31
int1/select_n
int0
ucs_n/once1_n
lcs_n/once0_n
pcs6_n/a2/pio2
pcs5_n/a1/pio3
vCC
pcs3_n/rts1_n/rtr1_n/pio19
pcs2_n/cts1_n/enrx1_n/pio18
gnd
pcs1_n/pio17
pcs0_n/pio16
vCC
mcs2_n/pio24
mcs3_n/rfsh_n/pio25
gnd
res_n
tmrin1/pio0
tmrout1/pio1
tmrout0/pio10
tmrin0/pio11
drq1/int6/pio13
drq0/int5/pio12
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 2. IA186ES TQFP Alphabetic Pin Listing
Name
a0
a1
a2
a3
a4
a5
a6
a7
a8
a9
a10
a11
a12
a13
a14
a15
a16
a17/pio7
a18/pio8
a19/pio9
ad0
ad1
ad2
ad3
ad4
ad5
ad6
ad7
ad8
ad9
ad10
ad11
ad12
ad13
Pin
63
62
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
43
42
1
3
5
7
9
11
14
17
2
4
6
8
10
13
®
Name
ad14
ad15
ale
ardy
bhe_n/aden_n
clkouta
clkoutb
cts0_n/enrx0_n/pio21
den_n/ds_n/pio5
drq0/int5/pio12
drq1/int6/pio13
dt/r_n/pio4
gnd
gnd
gnd
gnd
gnd
gnd
hlda
hold
int0
int1/select_n
int2/inta0_n/pwd/pio31
int3/inta1_n/irq
int4/pio30
lcs_n/once0_n
mcs0_n/pio14
mcs1_n/pio15
mcs2_n/pio24
mcs3_n/rfsh_n/pio25
nmi
pcs0_n/pio16
pcs1_npio
Pin
16
18
30
30
27
39
40
23
72
100
99
71
12
36
41
64
87
93
67
68
79
78
77
76
75
81
73
74
91
92
70
89
88
Name
pcs2_n/cts1_n/enrx1_n/pio18
pcs3_n/rts1_n/rtr1_n/pio19
pcs5_n/a1/pio3
pcs6_n/a2/pio2
rd_n
res_n
rts0_n/rtr0_n/pio20
rxd0/pio23
rxd1/pio28
s0_n
s1_n
s2_n
s6/lock_n/clkdiv2_n/pio29
srdy/pio6
tmrin0/pio11
tmrin1/pio0
tmrout0/pio10
tmrout1/pio1
txd0/pio22
txd1/pio27
ucs_n/once1_n
uzi_n/pio26
vCC
vCC
vCC
vCC
vCC
vCC
whb_n
wlb_n
wr_n
x1
x2
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 19 of 154
Pin
86
85
83
82
29
94
26
24
22
34
33
32
19
69
98
95
97
96
25
21
80
20
15
38
44
61
84
90
65
66
28
36
37
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
2.1.2
Data Sheet
November 15, 2011
IA188ES TQFP Package
drq0/int5/pio12
drq1/int6/pio13
tmrin0/pio11
tmrout0/pio10
tmrout1/pio1
tmrin1/pio0
res_n
gnd
mcs3_n/rfsh_n/pio25
mcs2_n/pio24
vcc
pcs0_n/pio16
pcs1_n/pio17
gnd
pcs2_n/cts1_n/enrx1_n/pio18
pcs3_n/rts1_n/rtr1_n/pio19
vcc
pcs5_n/a1/pio3
pcs6_n/a2/pio2
lcs_n/once0_n
ucs_n/once1_n
int0
int1/select_n
int2/inta0_n/pwd/pio31
int3/inta1_n/irq
The pinout for the IA186ES TQFP package is as shown in Figure 2. The corresponding pinout is
provided in Tables 3 and 4.
ad0
ao8
ad1
ao9
ad2
ao10
ad3
ao11
ad4
ao12
ad5
gnd
ao13
ad6
vcc
ao14
ad7
ao15
s6/lock_n/clkdiv2_n/pio29
uzi_n/pio26
txd1/pio27
rxd1/pio28
cts0_n/enrx0_n/pio21
rxd0/pio23
txd0/pio22
®
rts0_n/rtr0_n/pio20
rfsh2_n/aden_n
wr_n
rd_n
ale
ardy
s2_n
s1_n
s0_n
gnd
x1
x2
vcc
clkouta
clkoutb
gnd
a19/pio9
a18/pio8
vcc
a17/pio7
a16
a15
a14
a13
a12
IA188ES
TQFP
int4/pio30
mcs1_n/pio15
mcs0_n/pio14
den_n/ds_n/pio5
dt/r_n/pio4
nmi
srdy/pio6
hold
hlda
wb_n
gnd
gnd
a0
a1
vcc
a2
a3
a4
a5
a6
a7
a8
a9
a10
a11
Figure 2. IA188ES TQFP Package Diagram
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 20 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 3. IA188ES TQFP Numeric Pin Listing
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Name
ad0
ao8
ad1
ao9
ad2
ao10
ad3
ao11
ad4
ao12
ad5
gnd
ao13
ad6
vCC
ao14
ad7
ao15
s6/lock_n/clkdiv2_n/pio29
uzi_n/pio26
txd1/pio27
rxd1/pio28
cts0_n/enrx0_n/pio21
rxd0/pio23
txd0/pio22
rts0_n/rtr0_n/pio20
rfsh2_n/aden_n
wr_n
rd_n
ale
ardy
s2_n
s1_n
s0_n
®
Pin
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Name
gnd
x1
x2
vCC
clkouta
clkoutb
gnd
a19/pio9
a18/pio8
vCC
a17/pio7
a16
a15
a14
a13
a12
a11
a10
a9
a8
a7
a6
a5
a4
a3
a2
vCC
a1
a0
gnd
gnd
wb_n
hlda
Pin
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 21 of 154
Name
hold
srdy/pio6
nmi
dt/r_n/pio4
den_n/ds_n/pio5
mcs0_n/pio14
mcs1_n/pio15
int4/pio30
int3/inta1_n/irq
int2/inta0_n/pwd/pio31
int1/select_n
int0
ucs_n/once1_n
lcs_n/once0_n
pcs6_n/a2/pio2
pcs5_n/a1/pio3
vCC
pcs3_n/rts1_n/rtr1_n/pio19
pcs2_n/cts1_n/enrx1_n/pio18
gnd
pcs1_n/pio17
pcs0_n/pio16
vCC
mcs2_n/pio24
mcs3_n/rfsh_n/pio25
gnd
res_n
tmrin1/pio0
tmrout1/pio1
tmrout0/pio10
tmrin0/pio11
drq1/int6/pio13
drq0/int5/pio12
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 4. IA188ES TQFP Alphabetic Pin Listing
Name
a0
a1
a2
a3
a4
a5
a6
a7
a8
a9
a10
a11
a12
a13
a14
a15
a16
a17/pio7
a18/pio8
a19/pio9
ale
ad0
ad1
ad2
ad3
ad4
ad5
ad6
ad7
ao8
ao9
ao10
ao11
ao12
Pin
63
62
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
43
42
30
1
3
5
7
9
11
14
17
2
4
6
8
10
®
Name
ao13
ao14
ao15
ardy
clkouta
clkoutb
cts0_n/enrx0_n/pio21
den_n/ds_n/pio5
drq0/int5/pio12
drq1/int6/pio13
dt/r_n/pio4
gnd
gnd
gnd
gnd
gnd
gnd
gnd
hlda
hold
int0
int1/select_n
int2/inta0_n/pwd/pio31
int3/inta1_n/irq
int4/pio30
lcs_n/once0_n
mcs0_n/pio14
mcs1_n/pio15
mcs2_n/pio24
mcs3_n/rfsh_n/pio25
nmi
pcs0_n/pio16
pcs1_n/pio17
Pin
13
16
18
30
39
40
23
72
100
99
71
12
35
41
64
65
87
93
67
68
79
78
77
76
75
81
73
74
91
92
70
89
88
Name
pcs2_n/cts1_n/enrx1_n/pio18
pcs3_n/rts1_n/rtr1_n/pio19
pcs5_n/a1/pio3
pcs6_n/a2/pio2
rd_n
res_n
rfsh_n/aden_n
rts0_n/rtr0_n/pio20
rxd0/pio23
rxd1/pio28
s0_n
s1_n
s2_n
s6/lock_n/clkdiv2_n/pio29
srdy/pio6
tmrin0/pio11
tmrin1/pio0
tmrout0/pio10
tmrout1/pio1
txd0/pio22
txd1/pio27
ucs_n/once1_n
uzi_n/pio26
vCC
vCC
vCC
vCC
vCC
vCC
wb_n
wr_n
x1
x2
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 22 of 154
Pin
86
85
83
82
29
94
27
26
24
22
34
33
32
19
69
98
95
97
96
25
21
80
20
15
38
44
61
84
90
66
28
36
37
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
2.1.3
Data Sheet
November 15, 2011
TQFP Physical Dimensions
The physical dimensions for the TQFP are as shown in Figure 3.
Legend:
Seating
Plane
Millimeter
Inch
Symbol Min Nom Max Min Nom Max
A
–
– 1.20 –
– 0.047
A1
0.05 – 0.15 0.002 – 0.006
A2
0.95 1.00 1.05 0.037 0.039 0.041
b
0.17 0.20 0.27 0.007 0.008 0.011
c
0.09 – 0.20 0.004 – 0.008
D
16.00 BSC.
0.630 BSC.
D1
14.00 BSC.
0.551 BSC.
D2
12.00
0.472
e
0.50 BSC.
0.02 BSC.
E
16.00 BSC.
0.630 BSC.
E1
14.00 BSC.
0.551 BSC.
E2
12.00
0.472
L
0.45 0.60 0.75 0.018 0.024 0.030
L1
1.00 REF
0.039 REF
R1
0.08 –
– 0.003 –
–
R2
0.08 – 0.20 0.003 – 0.008
S
0.20 –
– 0.008 –
–
θ
0° 3.5° 7° 0° 3.5° 7°
0° –
–
0°
–
–
θ1
11° 12° 13° 11° 12° 13°
θ2
11° 12° 13° 11° 12° 13°
θ3
Tolerances of Form and Position
aaa
0.20
0.008
bbb
0.20
0.008
ccc
0.08
0.003
ddd
0.08
0.003
Note:
Control dimensions are in millimeters.
Figure 3. TQFP Package Dimensions
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 23 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
2.1.4
Data Sheet
November 15, 2011
IA186ES PQFP Package
cts0_n/enrx0_n/pio21
rxd1/pio28
txd1/pio27
uzi_n/pio26
s6/lock_n/clkdiv2_n/pio29
ad15
ad7
ad14
vcc
ad6
ad13
gnd
ad5
ad12
ad4
ad11
ad3
ad10
ad2
ad9
The pinout for the IA186ES PQFP package is as shown in Figure 4. The corresponding pinout is
provided in Tables 5 and 6.
®
®
IA186ES
IA186ES
PQFP
TQFP
ad1
ad8
ad0
drq0/int5/pio12
drq1/int6/pio13
tmrin0/pio11
tmrout0/pio10
tmrout1/pio1
tmrin1/pio0
res_n
gnd
mcs3_n/rfsh_n/pio25
mcs2_n/pio24
vcc
pcs0_n/pio16
pcs1_n/pio17
gnd
pcs2_n/cts1_n/enrx1_n/pio18
pcs3_n/rts1_n/rtr1_n/pio19
vcc
pcs5_n/a1/pio3
pcs6_n/a2/pio2
lcs_n/once0_n
ucs_n/once1_n
int0
int1/select_n
int2/inta0_n/pwd/pio31
int3/inta1_n/irq
int4/pio30
mcs1_n/pio15
a8
a7
a6
a5
a4
a3
a2
vcc
a1
a0
gnd
whb_n
wlb_n
hlda
hold
srdy/pio6
nmi
dt/r_n/pio4
den_n/ds_n/pio5
mcs0_n/pio14
rxd0/pio23
txd0/pio22
rts0_n/rtr0_n/pio20
bhe_n/aden_n
wr_n
rd_n
ale
ardy
s2_n
s1_n
s0_n
gnd
x1
x2
vcc
clkouta
clkoutb
gnd
a19/pio9
a18/pio8
vcc
a17/pio7
a16
a15
a14
a13
a12
a11
a10
a9
Figure 4. IA186ES PQFP Package Diagram
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 24 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 5. IA186ES PQFP Numeric Pin Listing
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Name
rxd0/pio23
txd0/pio22
rts0_n/rtr0_n/pio20
bhe_n/aden_n
wr_n
rd_n
ale
ardy
s2_n
s1_n
s0_n
gnd
x1
x2
vCC
clkouta
clkoutb
gnd
a19/pio9
a18/pio8
vCC
a17/pio7
a16
a15
a14
a13
a12
a11
a10
a9
a8
a7
a6
a5
®
Pin
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Name
a4
a3
a2
vCC
a1
a0
gnd
whb_n
wlb_n
hlda
hold
srdy/pio6
nmi
dt/r_n/pio4
den_n/ds_n/pio5
mcs0_n/pio14
mcs1_n/pio15
int4/pio30
int3/inta1_n/irq
int2/inta0_n/pwd/pio31
int1/select_n
int0
ucs_n/once1_n
lcs_n/once0_n
pcs6_n/a2/pio2
pcs5_n/a1/pio3
vCC
pcs3_n/rts1_n/rtr1_n/pio19
pcs2_n/cts1_n/enrx1_n/pio18
gnd
pcs1_n/pio17
pcs0_n/pio16
vCC
Pin
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 25 of 154
Name
mcs2_n/pio24
mcs3_n/rfsh_n/pio25
gnd
res_n
tmrin1/pio0
tmrout1/pio1
tmrout0/pio10
tmrin0/pio11
drq1/int6/pio13
drq0/int5/pio12
ad0
ad8
ad1
ad9
ad2
ad10
ad3
ad11
ad4
ad12
ad5
gnd
ad13
ad6
vCC
ad14
ad7
ad15
s6/lock_n/clkdiv2_n/pio29
uzi_n/pio26
txd1/pio27
rxd1/pio28
cts0_n/enrx0_n/pio21
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 6. IA186ES PQFP Alphabetic Pin Listing
Name
a0
a1
a2
a3
a4
a5
a6
a7
a8
a9
a10
a11
a12
a13
a14
a15
a16
a17/pio7
a18/pio8
a19/pio9
ad0
ad1
ad2
ad3
ad4
ad5
ad6
ad7
ad8
ad9
ad10
ad11
ad12
ad13
Pin
40
39
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
20
19
78
80
82
84
86
88
91
94
79
81
83
85
87
90
®
Name
ad14
ad15
ale
ardy
bhe_n/aden_n
clkouta
clkoutb
cts0_n/enrx0_n/pio21
den_n/ds_n/pio5
drq0/int5/pio12
drq1/int6/pio13
dt/r_n/pio4
gnd
gnd
gnd
gnd
gnd
gnd
hlda
hold
int0
int1/select_n
int2/inta0_n/pwd/pio31
int3/inta1_n/irq
int4/pio30
lcs_n/once0_n
mcs0_n/pio14
mcs1_n/pio15
mcs2_n/pio24
mcs3_n/rfsh_n/pio25
nmi
pcs0_n/pio16
pcs1_n/pio17
Pin
93
95
7
8
4
16
17
100
49
77
76
48
12
18
41
64
70
89
44
45
56
55
54
53
52
58
50
51
68
69
47
66
65
Name
pcs2_n/cts1_n/enrx1_n/pio18
pcs3_n/rts1_n/rtr1_n/pio19
pcs5_n/a1/pio3
pcs6_n/a2/pio2
rd_n
res_n
rts0_n/rtr0_n/pio20
rxd0/pio23
rxd1/pio28
s0_n
s1_n
s2_n
s6/lock_n/clkdiv2/pio29
srdy/pio6
tmrin0/pio11
tmrin1/pio0
tmrout0/pio10
tmrout1/pio1
txd0/pio22
txd1/pio27
ucs_n/once1_n
uzi_n/pio26
vCC
vCC
vCC
vCC
vCC
vCC
whb_n
wlb_n
wr_n
x1
x2
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 26 of 154
Pin
63
62
60
59
6
71
3
1
99
11
10
9
96
46
75
72
74
73
2
98
57
97
15
21
38
61
67
92
42
43
5
13
14
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
2.1.5
Data Sheet
November 15, 2011
IA188ES PQFP Package
cts0_n/enrx0_n/pio21
rxd1/pio28
txd1/pio27
uzi_n/pio26
s6/lock_n/clkdiv2_n/pio29
ao15
ad7
ao14
vcc
ad6
ao13
gnd
ad5
ao12
ad4
ao11
ad3
ao10
ad2
ao9
The pinout for the IA188ES PQFP package is as shown in Figure 5. The corresponding pinout is
provided in Tables 7 and 8.
rxd0/pio23
txd0/pio22
rts0_n/rtr0_n/pio20
bhe_n/aden_n
wr_n
rd_n
ale
ardy
s2_n
s1_n
s0_n
gnd
x1
x2
vcc
clkouta
clkoutb
gnd
a19/pio9
a18/pio8
vcc
a17/pio7
a16
a15
a14
a13
a12
a11
a10
a9
®
a8
a7
a6
a5
a4
a3
a2
vcc
a1
a0
gnd
gnd
wb_n
hlda
hold
srdy/pio6
nmi
dtr/r_n/pio4
den_n/ds_n/pio5
mcs0_n/pio14
IA188ES
IA186ES
PQFP
TQFP
ad1
ao8
ad0
drq0/int5/pio12
drq1/int6/pio13
tmrin0/pio11
tmrout0/pio10
tmrout1/pio1
tmrin1/pio0
res_n
gnd
mcs3_n/rfsh_n/pio25
mcs2_n/pio24
vcc
pcs0_n/pio16
pcs1_n/pio17
gnd
pcs2_n/cts1_n/enrx1_n/pio18
pcs3_n/rts1_n/rtr1_n/pio19
vcc
pcs5_n/a1/pio3
pcs6_n/a2/pio2
lcs_n/once0_n
ucs_n/once1_n
int0
int1/select_n
int2/inta0_n/pwd/pio31
int3/inta1_n/irq
int4/pio30
mcs1_n/pio15
Figure 5. IA188ES PQFP Package Diagram
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 27 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 7. IA188ES PQFP Numeric Pin Listing
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Name
rxd0/pio23
txd0/pio22
rts0_n/rtr0_n/pio20
bhe_n/aden_n
wr_n
rd_n
ale
ardy
s2_n
s1_n
s0_n
gnd
x1
x2
vCC
clkouta
clkoutb
gnd
a19/pio9
a18/pio8
vCC
a17/pio7
a16
a15
a14
a13
a12
a11
a10
a9
a8
a7
a6
a5
®
Pin
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Name
a4
a3
a2
vCC
a1
a0
gnd
gnd
wb_n
hlda
hold
srdy/pio6
nmi
dt/r_n/pio4
den_n/ds_n/pio5
mcs0_n/pio14
mcs1_n/pio15
int4/pio30
int3/inta1_n/irq
int2/inta0_n/pwd/pio31
int1/select_n
int0
ucs_n/once1_n
lcs_n/once0_n
pcs6_n/a2/pio2
pcs5_n/a1/pio3
vCC
pcs3_n/rts1_n/rtr1_n/pio19
pcs2_n/cts1_n/enrx1_n/pio18
gnd
pcs1_n/pio17
pcs0_n/pio16
vCC
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 28 of 154
Pin
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Name
mcs2_n/pio24
mcs3_n/rfsh_n/pio25
gnd
res_n
tmrin1/pio0
tmrout1/pio1
tmrout0/pio10
tmrin0/pio11
drq1/int6/pio13
drq0/int5/pio12
ad0
ao8
ad1
ao9
ad2
ao10
ad3
ao11
ad4
ao12
ad5
gnd
ao13
ad6
vCC
ao14
ad7
ao15
s6/lock_n/clkdiv2_n/pio29
uzi_n/pio26
txd1/pio27
rxd1/pio28
cts0_n/enrx0_n/pio21
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 8. IA188ES PQFP Alphabetic Pin Listing
Name
a0
a1
a2
a3
a4
a5
a6
a7
a8
a9
a10
a11
a12
a13
a14
a15
a16
a17/pio7
a18/pio8
a19/pio9
ad0
ad1
ad2
ad3
ad4
ad5
ad6
ad7
ale
ao8
ao9
ao10
ao11
ao12
Pin
40
39
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
20
19
78
80
82
84
86
88
91
94
7
79
81
83
85
87
®
Name
ao13
ao14
ao15
ardy
bhe_n/aden_n
clkouta
clkoutb
cts0_n/enrx0_n/pio21
den_n/ds_n/pio5
drq0/int5/pio12
drq1/int6/pio13
dt/r_n/pio4
gnd
gnd
gnd
gnd
gnd
gnd
gnd
hlda
hold
int0
int1/select_n
int2/inta0_n/pwd/pio31
int3/inta1_n/irq
Iint4/pio30
lcs_n/once0_n
mcs0_n/pio14
mcs1_n/pio15
mcs2_n/pio24
mcs3_n/rfsh_n/pio25
nmi
pcs0_n/pio16
pcs1_n/pio17
Pin
90
93
95
8
4
16
17
100
49
77
76
48
12
18
41
42
64
70
89
44
45
56
55
54
53
52
58
50
51
68
69
47
66
65
Name
pcs2_n/cts1_n/enrx1_n/pio18
pcs3_n/rts1_n/rtr1_n/pio19
pcs5_n/a1/pio3
pcs6_n/a2/pio2
rd_n
res_n
rts0_n/rtr0_n/pio20
rxd0/pio23
rxd1/pio28
s0_n
s1_n
s2_n
s6/lock_n/clkdiv2/pio29
srdy/pio6
tmrin0/pio11
tmrin1/pio0
tmrout0/pio10
tmrout1/pio1
txd0/pio22
txd1/pio27
ucs_n/once1_n
uzi_n/pio26
vCC
vCC
vCC
vCC
vCC
vCC
wb_n
wr_n
x1
x2
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 29 of 154
Pin
63
62
60
59
6
71
3
1
99
11
10
9
96
46
75
72
74
73
2
98
57
97
15
21
38
61
67
92
43
5
13
14
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
2.1.6
Data Sheet
November 15, 2011
PQFP Physical Dimensions
The physical dimensions for the PQFP are as shown in Figure 6.
Pin 1 Indicator
See Detail “B”
See Detail “A”
PLATING
Detail “B”
Detail “A”
Legend
Millimeter
Inch
Symbol Min Nom Max Min Nom Max
A
–
– 3.40 –
– 0.134
A1
0.25 –
– 0.010 –
–
A2
2.73 2.85 2.97 0.107 0.112 0.117
B
0.25 0.30 0.38 0.010 0.012 0.015
B1
0.22 0.30 0.33 0.009 0.012 0.013
C
0.13 0.15 0.23 0.005 0.006 0.009
C1
0.11 0.15 0.17 0.004 0.006 0.007
D
23.00 23.20 23.40 0.906 0.913 0.921
D1
19.90 20.00 20.10 0.783 0.787 0.791
E
17.00 17.20 17.40 0.669 0.677 0.685
E1
13.90 14.00 14.10 0.547 0.551 0.555
0.65 BSC.
0.026 BSC.
e
L
0.73 0.88 1.03 0.029 0.035 0.041
L1
1.60 BSC.
0.063 BSC.
R1
0.13 –
– 0.005 –
–
R2
0.13 – 0.30 0.005 – 0.012
S
0.20 –
– 0.008 –
–
Y
–
– 0.10 –
– 0.004
θ
–
–
0
7
0
7
θ1
–
–
–
–
0
0
θ2
9
10
11
9
10
11
θ3
9
10
11
9
10
11
Notes:
1. Dimensions D1 and E1 do not include
mold protrusion, but mold mismatch is
included. Allowable protrusion is
0.25mm/0.010 per side.
2. Dimension B does not include Dambar
protrusion. Allowable protrusion is
0.08mm/0.003 total in excess of the B
dimension at maximum material
condition. Dambar cannot be located
on the lower radius or the foot.
3. Controlling dimension: millimeter.
Figure 6. PQFP Package Dimensions
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 30 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
2.2
2.2.1
Data Sheet
November 15, 2011
Pin Descriptions
a19/pio9, a18/pio8, a17/pio7, a16–a0—Address Bus (synchronous outputs with
tristate)
These pins are the system’s source of non-multiplexed I/O or memory addresses and occur a half
clkouta cycle before the multiplexed address/data bus (ad15–ad0 for the IA186ES or ao15–ao8
and ad7–ad0 for the IA188ES).
The address bus is tristated during a bus hold or reset.
2.2.2
ad15–ad8 (IA186ES)—Address/Data Bus (level-sensitive synchronous inouts with
tristate)
These pins are the system’s source of time-multiplexed I/O or memory addresses and data. The
address function of these pins may be disabled (see bhe_n/aden_n pin description). If the
address function of these pins is enabled, the address will be present on this bus during t1 of the
bus cycle and data will be present during t2, t3, and t4 of the same bus cycle.
If whb_n is not active, these pins are tristated during t2, t3, and t4 of the bus cycle.
The address/data bus is tristated during a bus hold or reset.
These pins may be used to load the internal Reset Configuration register (RESCON, offset 0F6h)
with configuration data during a POR.
2.2.3
ao15–ao8 (IA188ES)—Address Bus (level-sensitive synchronous outputs with
tristate)
The address bus will contain valid high order address bits during the bus cycle (t1, t2, t3, and t4) if
the bus is enabled by the AD bit in the Upper and Lower Memory Chip Select registers (UMCS,
offset 0a0h, and LMCS, offset 0a2h).
These pins are combined with ad7–ad0 to complete the multiplexed address bus and are tristated
during a bus hold or reset condition.
2.2.4
ad7–ad0—Address/Data Bus (level-sensitive synchronous inouts with tristate)
These pins are the system’s source of time-multiplexed low order byte of the addresses for I/O or
memory and 8-bit data. The low order address byte will be present on this bus during t1 of the
bus cycle and the 8-bit data will be present during t2, t3, and t4 of the same bus cycle.
The address function of these pins may be disabled (see bhe_n/aden_n pin description).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 31 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
If wlb_n is not active, these pins are tristated during t2, t3, and t4 of the bus cycle. The
address/data bus is tristated during a bus hold or reset.
2.2.5
ale—Address Latch Enable (synchronous output)
This signal indicates the presence of an address on the address bus (ad15–ad0 for the IA186ES or
ao15–ao8 and ad7–ad0 for the IA188ES), which is guaranteed to be valid on the falling edge of
ale.
In ONCE mode, this pin is tristated but not during bus hold or reset.
2.2.6
ardy—Asynchronous Ready (level-sensitive asynchronous input)
This asynchronous signal provides an indication to the microcontroller that the addressed I/O
device or memory space will complete a data transfer. This active high signal is asynchronous
with respect to clkouta. If the falling edge of ardy is not synchronized to clkouta, an additional
clock cycle may be added. The ardy or srdy must be synchronized to clkouta to guarantee the
number of inserted wait states.
The ardy should be tied high to maintain a permanent assertion of the ready condition. On the
other hand, if the ardy signal is not used by the system, it should be tied low, which passes
control to the srdy signal.
2.2.7
bhe_n/aden_n (IA186ES only)—Bus High Enable (synchronous output with
tristate)/Address Enable (input with internal pullup)
The bhe_n–bhe_n and address bit ad0 or a0 inform the system which bytes of the data bus
(upper, lower, or both) are involved in the current memory access bus cycle, as shown in
Table 9.
Table 9. Bus Cycle Types for bhe_n and ad0
bhe_n
0
0
1
1
ad0
0
1
0
1
Type of Bus Cycle
Word Transfer
High Byte Transfer (Bits [15–8])
Low Byte Transfer (Bits [7–0])
Refresh
The bhe_n does not require latching and during bus hold and reset is tristated. It is asserted
during t1 and remains so through t3 and tw.
The high- and low-byte write enable functions of bhe_n and ad0 are performed by whb_n and
wlb_n, respectively.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 32 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
When using the ad bus, DRAM refresh cycles are indicated by bhe_n/aden_n and ad0, both
being high. During refresh cycles, the a and ad busses may not have the same address during the
address phase of the ad bus cycle. This would necessitate the use of ad0 as a determinant for the
refresh cycle, rather than A0.
An additional signal is used for Pseudo-Static RAM (PSRAM) refreshes (see mcs3_n/rfsh_n pin
description), aden_n. There is a weak internal pullup on bhe_n/aden_n , eliminating the need for
an external pullup and reducing power consumption.
Holding aden_n high or letting it float during power-on reset (POR), passes control of the
address function of the ad bus (ad15–ad0) during LCS and UCS bus cycles from aden_n to the
Disable Address (DA) bit in LMCS and UMCS registers. When the address function is selected,
the memory address is placed on the a19–a0 pins.
When holding aden_n low during POR, both the address and data are driven onto the ad bus
independently of the DA bit setting. This pin is normally sampled on the rising edge of res_n
and the condition of s6 and uzi_n default to their normal functions.
2.2.8
clkouta—Clock Output A (synchronous output)
This pin is the internal clock output to the system. Bits [9–8] and Bits [2–0] of the System
Configuration (SYSCON) register control the output of this pin, which may be disabled, output
the PLL frequency, or output the power save frequency (internal processor frequency after
divisor). The clkouta may be used as a full-speed clock source in power-save mode. The AC
timing specifications that are clock-related refer to clkouta, which remains active during reset
and hold conditions.
2.2.9
clkoutb—Clock Output B (synchronous output)
This pin is an additional clock output to the system with and output delayed with respect to
clkouta. Bits [11–10] and Bits [2–0] of the SYSCON register control the output of this pin,
which may be disabled, output the PLL frequency, or may output the power save frequency
(internal processor frequency after divisor). The clkoutb may be used as a full-speed clock
source in power-save mode and remains active during reset and hold conditions.
2.2.10 cts0_n/enrx0_n/pio21—Clear-to-Send 0/Enable-Receive-Request 0 (both are
asynchronous inputs)
The cts0_n is the Clear-to-Send signal for asynchronous serial port 0, provided that Bit [4]
(ENRX0) in the AUXCON register is 0, and Bit [9] (FC) in the SP0CT register is 1. The cts0_n
controls the transmission of data from asynchronous serial port 0. When it is asserted, the
transmitter begins transmitting the next frame of data. When it is not asserted, the data to be
transmitted is held in the transmit register. This signal is checked only at the start of data frame
transmission.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 33 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
The enrx0_n is the Enable-Receiver-Request for asynchronous serial port 0 when Bit [4]
(ENRX0) in the AUXCON register is 1, and Bit [9] (FC) in the SP0CT register is 1, and it
enables the asynchronous serial port receiver.
2.2.11 den_n/ds_n/pio5—Data Enable /Data Strobe (both are synchronous outputs with
tristate)
den_n is asserted during I/O, memory, and interrupt acknowledge processes and is deasserted
when dt/r_n undergoes a change of state. It is tristated for a bus hold or reset. After reset, this
pin defaults to den_n.
The data strobe ds_n is used under conditions in which a write cycle has the same timing as a
read cycle. It is used with other control signals to interface with 68-Kbyte-type peripherals
without further system interface logic. When it is asserted, addresses are valid. During a write,
the data is valid, while during a read, data may be applied to the ad bus.
2.2.12 drq0/int5/pio12—DMA Request 0 (synchronous level-sensitive input)/Maskable
Interrupt Request 5 (asynchronous edge-triggered input)
The drq0 is an external device that is ready for DMA channel 0 to carry out a transfer. It
indicates to the microcontroller this readiness on this pin. It is not latched and must remain
asserted until it is dealt with.
If DMA channel 0 is not required, int5 may be used as an extra interrupt request sharing the
DMA0 interrupt type (0ah) and control bits. It is not latched and must remain asserted until it is
dealt with.
2.2.13 drq1/int6/pio13—DMA Request 1 (synchronous level-sensitive input)/Maskable
Interrupt Request 6 (asynchronous edge-triggered input)
The drq1 is an external device that is ready for DMA channel 1 to carry out a transfer. It
indicates to the microcontroller this readiness on this pin. It is not latched and must remain
asserted until it is dealt with.
If DMA channel 1 is not required, int6 may be used as an extra interrupt request sharing the
DMA1 interrupt type (0bh) and control bits. It is not latched and must remain asserted until it is
dealt with.
2.2.14 dt/r_n/pio4—Data Transmit or Receive (synchronous output with tristate)
The microntroller transmits data when dt/r_n is pulled high and receives data when this pin is
pulled low. It floats during a reset or bus hold condition.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 34 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
2.2.15 gnd—Ground
Depending on the package, six or seven pins connect the microcontroller to the system ground.
2.2.16 hlda—Bus Hold Acknowledge (synchronous output)
This pin is pulled high to signal the system that the microntroller has relinquished control of the
local bus, in response to a high on the hold signal by an external bus master, after the
microcontroller has completed the current bus cycle. The assertion of hlda is accompanied by
the tristating of den_n, rd_n, wr_n, s2–s0, ad15–ad0, s6, a19–a0, bhe_n, whb_n, wlb_n, and
dr/r_n, followed by the driving high of the chip selects ucs_n, lcs_n, mcs3_n–mcs0_n, pcs6_n–
pcs5_n, and pcs3_n–pcs0_n. The external bus master releases control of the local bus by the
deassertion of hold that in turn induces the microcontroller to deassert the hlda. The
microcontroller may take control of the bus if necessary (to execute a refresh for example), by
deasserting hlda without the bus master first deasserting hold. This requires that the external bus
master must be able to deassert hold to permit the microcontroller to access the bus.
2.2.17 int0—Maskable Interrupt Request 0 (asynchronous input)
The int0 pin provides an indication that an interrupt request has occurred, and provided that int0
is not masked, program execution will continue at the location specified by the INT0 vector in
the interrupt vector table. Although interrupt requests are asynchronous, they are synchronized
internally and may be edge- or level-triggered. To ensure that it is recognized, the assertion of
the interrupt request must be maintained until it is handled.
2.2.18 int1/select_n—Maskable Interrupt Request 1/Slave Select (both are asynchronous
inputs)
The int1 pin provides an indication that an interrupt request has occurred. Provided that int1 is
not masked, program execution will continue at the location specified by the INT1 vector in the
interrupt vector table. Although interrupt requests are asynchronous, they are synchronized
internally and may be edge- or level-triggered. To ensure that it is recognized, the assertion of
the interrupt request must be maintained until it is handled.
The select_n pin provides an indication to the microcontroller that an interrupt type has been
placed on the address/data bus when the internal Interrupt Control Unit is slaved to an external
interrupt controller. However, before this occurs, the int0 pin must have indicated an interrupt
request has occurred.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 35 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
2.2.19 int2/inta0_n/pwd/pio31—Maskable Interrupt Request 2 (asynchronous
input)/Interrupt Acknowledge 0 (synchronous output)/Pulse Width Demodulator
(Schmitt trigger input)
The int2 pin provides an indication that an interrupt request has occurred. Provided that int1 is
not masked, program execution will continue at the location specified by the int1 vector in the
interrupt vector table. Although interrupt requests are asynchronous, they are synchronized
internally and may be edge- or level-triggered. To ensure that it is recognized, the assertion of
the interrupt request must be maintained until it is handled. When int0 is configured to be in
cascade mode, int2 changes its function to inta0_n.
The inta0_n function indicates to the system that the microcontroller requires an interrupt type in
response to the interrupt request int0 when the microcontroller’s Interrupt Control Unit is in
cascade mode.
The pwd processes a signal via the Schmitt trigger when pulse width demodulation is enabled. It
drives timrin0 and int2 and its inverse signal drives timrin1 and int4. Provided that int2 and int4
are enabled and timer0 and timer1 are configured correctly, the pulse width of the alternating
signal on pwd may be calculated from the values in timer0 and timer1.
While in pwd mode, tmrin0/pio11, tmrin1/pio0, and int4/pio31 signals are free for use as PIOs or
may be ignored. The level on this pin is held in the PIO data register in the pio31 position, just
as if it were a PIO.
2.2.20 int3/inta1_n/irq—Maskable Interrupt Request 3 (asynchronous input)/Interrupt
Acknowledge 1 (synchronous output)/Interrupt Acknowledge (synchronous
output)
The int3 pin provides an indication that an interrupt request has occurred. Provided that int3 is
not masked, program execution will continue at the location specified by the int3 vector in the
interrupt vector table. Although interrupt requests are asynchronous, they are synchronized
internally and may be edge- or level-triggered. To ensure that it is recognized, the assertion of
the interrupt request must be maintained until it is handled. When int1 is configured to be in
cascade mode, int3 changes its function to inta1_n.
The inta1_n function indicates to the system that the microcontroller requires an interrupt type in
response to the interrupt request int1 when the microcontroller’s Interrupt Control Unit is in
cascade mode.
With the Interrupt Control Unit of the microcontroller in slave mode, the signal on the irq pin
allows the microcontroller to output an interrupt request to the external master interrupt
controller.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 36 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
2.2.21 int4/pio30—Maskable Interrupt Request 4 (asynchronous input)
The int4 pin provides an indication that an interrupt request has occurred. And provided that int4
is not masked, program execution will continue at the location specified by the int4 vector in the
interrupt vector table. Although interrupt requests are asynchronous, they are synchronized
internally and may be edge- or level-triggered. To ensure that it is recognized, the assertion of
the interrupt request must be maintained until it is handled. In the case where PWD mode is
selected, int4 indicates a High-to-Low transition of the PWD signal. Conversely, in the event
that PWD mode is not selected, int4 may be used as a PIO.
2.2.22 lcs_n/once0_n—Lower Memory Chip Select (synchronous output with internal
pullup)/ONCE Mode Request (input)
The lcs_n pin provides an indication that a memory access is in progress to the lower memory
block. The size of the Lower Memory Block and its base address are programmable, with the
size adjustable up to 512 Kbytes. The lcs_n may be configured for either an 8- or 16-bit bus
width for the IA186ES microcontroller by the Auxiliary Configuration Register (AUXCON Bit
[2]) and is held high during bus hold.
The once0_n pin (ON Circuit Emulation) and its companion pin once1_n define the
microcontroller mode during reset. These two pins are sampled on the rising edge of res_n and if
both are asserted low the microcontroller starts in ONCE mode, else it starts normally. In ONCE
mode, all pins are tristated and remain so until a subsequent reset. To prevent the
microcontroller from entering ONCE mode inadvertently, this pin has a weak pullup that is only
present during reset. Finally this pin is not tristated during bus hold.
2.2.23 mcs0_n/pio14—Midrange Memory Chip Select (synchronous output with internal
pullup)
The mcs0_n pin provides an indication that a memory access is in progress to the midrange
memory block. The size of the Midrange Memory Block and its base address are programmable.
The mcs0_n may be configured for either an 8- or 16-bit bus width for the IA186ES
microcontroller by the Auxiliary Configuration Register (AUXCON Bit [1]) and is held high
during bus hold. The mcs0_n may be programmed as the chip select for the whole middle chip
select address range. Furthermore, this pin has a weak pullup that is only present during reset.
2.2.24 mcs2_n–mcs1_n (pio24–pio 15)—Midrange Memory Chip Selects (synchronous
outputs with internal pullup)
The mcs2_n and mcs1_n pins provide an indication that a memory access is in progress to the
second or third midrange memory block. The size of the Midrange Memory Block and its base
address are programmable. The mcs2_n and mcs1_n may be configured for either an 8- or 16-bit
bus width for the IA186ES microcontroller by the Auxiliary Configuration Register (AUXCON
Bit [1]) and are held high during bus hold. Furthermore, these pins have weak pullups that are
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 37 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
present only during reset. If mcs0_n has been programmed as the chip select for the whole
middle chip select address range, these pins may be used as PIOs.
2.2.25 mcs3_n/rfsh_n/pio25—Midrange Memory Chip Select (synchronous outputs with
internal pullup)/Automatic Refresh (synchronous output)
The mcs3_n pin provides an indication that a memory access is in progress to the fourth region
of the midrange memory block. The size of the Midrange Memory Block and its base address
are programmable. The mcs3_n may be configured for either an 8- or 16-bit bus width for the
IA186ES microcontroller by the Auxiliary Configuration Register (AUXCON Bit [1]) and is
held high during bus hold. If mcs0_n has been programmed as the chip select for the whole
middle chip select address range, this pin may be used as PIO. Furthermore, this pin has a weak
pullup that is only present during reset.
The rfsh_n signal is timed for auto refresh to PSRAM or DRAM devices. The refresh pulse is
only output when the PSRAM or DRAM mode bit is set (EDRAM register Bit [15]). This pulse
is of 1.5 clock pulse duration with the rest of the refresh cycle made up of a deassertion period
such that the overall refresh time is met. Finally this pin is not tristated during a bus hold.
2.2.26 nmi—Nonmaskable Interrupt (synchronous edge-sensitive input)
This is the highest priority interrupt signal and cannot be masked, unlike int6–int0.
Program execution is transferred to the nonmaskable interrupt vector in the interrupt vector table,
upon the assertion of this interrupt (transition from low to high), and this interrupt is initiated at
the next instruction boundary. For recognition to be assured, the nmi pin must be held high for at
least a clkouta period.
The nmi is not involved in the priority resolution process, which deals with the maskable
interrupts and does not have an associated interrupt flag. This allows for a new nmi request to
interrupt an nmi service routine that is already underway. The interrupt flag IF is cleared,
disabling the maskable interrupts, when an interrupt is taken by the processor. If, during the nmi
service routine, the maskable interrupts are re-enabled, by use of STI instruction for example, the
priority resolution of maskable interrupts will be unaffected by the servicing of the nmi. For this
reason, it is strongly recommended that the nmi interrupt service routine does not enable the
maskable interrupts.
2.2.27 pcs1_n–pcs0_n (pio17–pio16)—Peripheral Chip Selects 1–0 (synchronous
outputs)
These pins provide an indication that a memory access is under way for the second and first
regions, respectively, of the peripheral memory block (I/O or memory address space). The base
address of the peripheral memory block is programmable. The pcs3_n–pcs0_n are held high
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 38 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
during both bus hold and reset. These outputs are asserted with the ad address bus over a
256 byte range each.
2.2.28 pcs2_n/cts1_n/enrx1_n/pio18—Peripheral Chip Select 2 (synchronous
output)/Clear-to-Send 1 (asynchronous input)/Enable-Receiver-Request 1
(asynchronous input)
The pcs2_n signal provides an indication that a memory access is under way for the third region
of the peripheral memory block (I/O or memory address space). The base address of the
peripheral memory block is programmable. The pcs2_n is held high during both bus hold and
reset. This output is asserted with the ad address bus over a 256-byte range.
The cts1_n is the Clear-to-Send signal for asynchronous serial port 1 when the ENRX1 bit
(Bit [6]) in the auxiliary control register (AUXCON) is 0 and hardware flow control is enabled
for this port (FC bit [Bit (9)] in the serial port 1 control register [SP1CT]). This signal controls
the transmission of data from the serial port transmit register 1. When this signal is asserted, the
transmitter begins sending out a frame of data if any is in the transmit register, whereas if the
signal is deasserted, the data will be held in the transmit register. The signal is checked at the
beginning of each frame of transmit data.
The enrx1_n is the Enable-Receiver-Request for asynchronous serial port 1 when the enrx1 bit
(Bit [6]) in the auxiliary control register (AUXCON) is 1 and hardware flow control is enabled
for this port (FC bit [Bit (9)] in the serial port 1 control register [SP1CT]). This signal enables
the receiver of asynchronous serial port 1.
2.2.29 pcs3_n/rts1_n/rtr1_n/pio18—Peripheral Chip Select 3 (synchronous
output)/Ready-to-Send 1 (asynchronous output)/Ready-to-Receive 1
(asynchronous input)
The pcs3_n signal provides an indication that a memory access is under way for the fourth region
of the peripheral memory block (I/O or memory address space). The base address of the
Peripheral memory block is programmable. The pcs3_n is held high during both bus hold and
reset. This output is asserted with the ad address bus over a 256-byte range.
The rts1-n is the Ready-to-Send signal for asynchronous serial port 1 when the RTS1 bit (Bit [5])
in the auxiliary control register (AUXCON) is 1 and hardware flow control is enabled for this
port (FC bit [Bit (9)] in the serial port 1 control register [SP1CT]). This signal is asserted when
the serial port transmit register contains untransmitted data.
The rtr1-n is the Ready-to-Receive signal for asynchronous serial port 1 when the rts1 bit
(Bit [5]) in the auxiliary control register (AUXCON) is 0 and hardware flow control is enabled
for this port (FC bit [Bit (9)] in the serial port 1 control register [SP1CT]). This signal is asserted
when the serial port receive register does not contain valid, unread data.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 39 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
2.2.30 pcs5_n/A1/pio3—Peripheral Chip Select 5 (synchronous output)/Latched Address
Bit [1] (synchronous output)
The pcs5_n signal provides an indication that a memory access is under way for the sixth region
of the peripheral memory block (I/O or memory address space). The base address of the
peripheral memory block is programmable. The pcs5_n is held high during both bus hold and
reset. This output is asserted with the ad address bus over a 256-byte range.
The A1 pin provides and internally latched address Bit [1] to the system when the EX bit
(Bit [7]) in the mcs_n and pcs_n auxiliary (MPCS) register is 0. It retains its previously latched
value during a bus hold.
2.2.31 pcs6_n/A2/pio2—Peripheral Chip Select 6 (synchronous output)/Latched Address
Bit [2] (synchronous output)
The pcs6_n signal provides an indication that a memory access is underway for the seventh
region of the peripheral memory block (I/O or memory address space). The base address of the
peripheral memory block is programmable. The pcs6_n is held high during both bus hold and
reset. This output is asserted with the ad address bus over a 256-byte range.
The A2 pin provides an internally latched address Bit [2] to the system when the EX bit (Bit [7])
in the MPCS register is 0. It retains its previously latched value during a bus hold.
2.2.32 pio31–pio0—Programmable I/O Pins (asynchronous input/output open-drain)
There are 32 individually PIO pins provided.
2.2.33 rd_n—Read strobe (synchronous output with tristate)
This pin provides an indication to the system that a memory or I/O read cycle is underway. It
will not to be asserted before the ad bus is floated during the address to data transition. The rd_n
is tristated during bus hold.
2.2.34 res_n—Reset (asynchronous level-sensitive input)
This pin forces a reset on the microcontroller. It has a Schmitt trigger to allow POR generation
via an RC network. When this signal is asserted, the microcontroller immediately terminates its
present activity, clears its internal logic, and transfers CPU control to the reset address, FFFF0h.
The res_n must be asserted for at least 1 ms and may be asserted asynchronously to clkouta as it
is synchronized internally. Furthermore, vcc must be within specification and clkouta must be
stable for more than four of its clock periods for the period that res_n is asserted. The
microcontroller starts to fetch instructions 6.5 clkouta clock periods after the deassertion of
res_n.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 40 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
2.2.35 rfsh2_n/aden_n (IA188ES only)—Refresh 2 (synchronous output with
tristate)/Address Enable (input with internal pullup)
The rfsh2_n indicates that a DRAM refresh cycle is being performed when it is asserted low.
However, this is not valid in PSRAM mode where mcs3_n/rfsh_n is used instead.
If aden_n is held high during POR, the ad bus (ao15–ao8 and ad7–ad0) is controlled during the
address portion of the LCS and UCS bus cycles by the DA bit (Bit [7]) in the LMCS and UMCS
registers. If the DA bit is 1, the address is accessed on the a19–a0 pins reducing power
consumption. The weak pullup on this pin obviates the necessity of an external pullup.
If this pin is held low during POR, the ad bus is used for both addresses and data without regard
for the setting of the DA bits. The rfsh2_n/aden_n is sampled one crystal clock cycle after the
rising edge of res_n and is tristated during bus holds and ONCE mode.
2.2.36 rts0_n/rtr0_n/pio20—Ready-to-Send 0 (asynchronous output)/Ready-to-Receive 0
(asynchronous input)
The rts0-n is the Ready-to-Send signal for asynchronous serial port 0 when the RTS0 bit (Bit [3])
in the auxiliary control register (AUXCON) is 1 and hardware flow control is enabled for this
port (FC bit [Bit (9)] in the serial port 1 control register [SP1CT]). This signal is asserted when
the serial port transmit register contains untransmitted data.
The rtr0-n is the Ready-to-Receive signal for asynchronous serial port 0 when the rts0 bit
(Bit [3]) in the auxiliary control register (AUXCON) is 0 and hardware flow control is enabled
for this port (FC bit [Bit (9)] in the serial port 1 control register [SP1CT]). This signal is asserted
when the serial port receive register does not contain valid unread data.
2.2.37 rxd0_n/pio23—Receive Data 0 (asynchronous input)
This signal connects asynchronous serial receive data from the system to the asynchronous Serial
Port 0.
2.2.38 rxd1_n/pio28—Receive Data 1 (asynchronous input)
This signal connects asynchronous serial receive data from the system to the asynchronous Serial
Port 1.
2.2.39 s2_n–s0_n—Bus Cycle Status (synchronous outputs with tristate)
These three signals inform the system of the type of bus cycle is in progress. The s2_n may be
used to indicate whether the current access is to memory or I/O, and s1_n may be used to
indicate whether data is being transmitted or received. These signals are tristated during bus
hold and hold acknowledge. The coding for these pins is presented in Table 10.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 41 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 10. Bus Cycle Types for s2_n, s1_n, and s0_n
s2_n
0
0
0
0
1
1
1
1
s1_n
0
0
1
1
0
0
1
1
s0_n
0
1
0
1
0
1
0
1
Bus Cycle
Interrupt acknowledge
Read data from I/O
Write data to I/O
Halt
Instruction fetch
Read data from memory
Write data to memory
None (passive)
2.2.40 s6/lock_n/clkdiv2_n/pio29—Bus Cycle Status Bit [6] (synchronous output)/Bus
Lock (synchronous output)/Clock Divide by 2 (input with internal pullup)
The s6 signal is high during the second and remaining cycle periods (i.e., t2–t4), indicating that a
DMA-initiated bus cycle is under way. The s6 is tristated during bus hold or reset.
The lock_n signal is held low to indicate to other system bus masters that the system bus is being
used and that no attempt should be made to try to gain control of it. This signal is only available
during t1 and is intended for emulator use.
The microcontroller enters clock divide-by-2 mode, if clkdiv2_n is held low during power-onreset. In this mode, the PLL is disabled and the processor receives the external clock divided
by 2. Sampling of this pin occurs on the rising edge of res_n.
Should this pin be used as pio29 configured as an input, care should be taken that it is not driven
low during power-on-reset. This pin has an internal pullup so it is not necessary to drive the pin
high even though it defaults to an input PIO.
2.2.41 srdy/pio6—Synchronous Ready (synchronous level-sensitive input)
This signal is an active high input synchronized to clkouta and indicates to the microcontroller
that a data transfer will be completed by the addressed memory space or I/O device.
In contrast to the asynchronous ready (ardy), which requires internal synchronization, srdy
permits easier system timing as it already synchronized. Tying srdy high will always assert this
ready condition, whereas tying it low will give control to ardy.
2.2.42 tmrin0/pio11—Timer Input 0 (synchronous edge-sensitive input)
This signal may be either a clock or control signal for the internal timer 0. The timer is
incremented by the microcontroller after it synchronizes a rising edge of tmrin0. When not used,
tmrin0 must be tied high, or when used as pio11 it is pulled up internally.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 42 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
When Pulse Width Demodulation mode is enabled, tmrin0 is driven internally by
int2/inta0_n/pwd allowing for the pin to be configured as pio11.
2.2.43 tmrin1/pio0—Timer Input 1 (synchronous edge-sensitive input)
This signal may be either a clock or control signal for the internal timer 1. The timer is
incremented by the microcontroller after it synchronizes a rising edge of tmrin1. When not used,
tmrin1 must be tied high. When used as pio0, it is pulled up internally. When pulse width
demodulation mode is enabled, tmrin1 is driven internally by int2/inta0_n/pwd, allowing for the
pin to be configured as pio0.
2.2.44 tmrout0/pio10—Timer Output 0 (synchronous output)
This signal provides the system with a single pulse or a continuous waveform with a
programmable duty cycle. It is tristated during a bus hold or reset.
2.2.45 tmrout1/pio1—Timer Output 1 (synchronous output)
This signal provides the system with a single pulse or a continuous waveform with a
programmable duty cycle. It is tristated during a bus hold or reset.
2.2.46 txd0/pio22—Transmit Data 0 (asynchronous output)
This pin provides the system with asynchronous serial transmit data from serial port 0.
2.2.47 txd1/pio27—Transmit Data 1 (asynchronous output)
This pin provides the system with asynchronous serial transmit data from serial port 1.
2.2.48 ucs_n/once1_n—Upper Memory Chip Select (synchronous output)/ONCE Mode
Request 1 (input with internal pullup)
The ucs_n pin provides an indication that a memory access is in progress to the upper memory
block. The size of the upper memory block and its base address are programmable, with the size
adjustable up to 512 Kbytes. The ucs_n is held high during bus hold.
After reset, ucs_n is active for the 64-Kbyte memory range from F0000h to FFFFFh, which
includes the reset address at FFFF0h.
The once1_n pin (ON Circuit Emulation) and its companion pin, once0_n, define the
microcontroller mode during reset. These two pins are sampled on the rising edge of res_n and if
both are asserted low, the microcontroller starts in ONCE mode, otherwise it starts normally. In
ONCE mode, all pins are tristated and remain so until a subsequent reset. To prevent the
microcontroller from entering ONCE mode inadvertently, this pin has a weak pullup that is only
present during reset. This pin is not tristated during bus hold.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 43 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
2.2.49 uzi_n/pio26—Upper Zero Indicate (synchronous output)
This pin allows the designer to determine if an access to the interrupt vector table is in progress
by ORing it with Bits [15–10] of the address and data bus (ad15–ad10 on the AI186 and ao15–
ao10 on the IA188ES). The uzi_n is the logical AND of the inverted a19–a16 bits. It asserts in
the first period of a bus cycle and is held throughout the cycle.
2.2.50 vcc—Power Supply (input)
These pins supply power (+5V +10%) to the microcontroller.
2.2.51 whb_n (IA186ES only)—Write High Byte (synchronous output with tristate)
This pin and wlb_n provide an indication to the system of which bytes of the data bus (upper,
lower, or both) are taking part in a write cycle. The whb_n is asserted with ad15–ad8 and is the
logical OR of bhe_n and wr_n. It is tristated during reset.
2.2.52 wlb_n/wb_n—Write Low Byte (IA186ES only) (synchronous output with
tristate)/Write Byte (IA188ES only) (synchronous output with tristate)
The wlb_n and whb_n provide an indication to the system of which bytes of the data bus (upper,
lower, or both) are taking part in a write cycle. The wlb_n is asserted with ad7–ad0 and is the
logical OR of ad0 and wr_n. It is tristated during reset.
On the IA188ES microcontroller, wb_n provides an indication that a write to the bus is
occurring. It shares the same early timing as that of the non-multiplexed address bus, and is
associated with ad7–ad0. It is tristated during reset.
2.2.53 wr_n—Write Strobe (synchronous output)
This pin provides an indication to the system that the data currently on the bus is to be written to
a memory or I/O device. It is tristated during a bus hold or reset.
2.2.54 x1—Crystal Input
This pin and x2 are the connections for a fundamental mode or third-overtone, parallel-resonant
crystal used by the internal oscillator circuit. An external clock source for the microcontroller is
connected to x1 while the x2 pin is left unconnected.
2.2.55 x2—Crystal Input
This pin and x1 are the connections for a fundamental mode or third-overtone, parallel-resonant
crystal used by the internal oscillator circuit. An external clock source for the microcontroller is
connected to x1 while the x2 pin is left unconnected.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 44 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
2.3
Data Sheet
November 15, 2011
Pins Used by Emulators
The following pins are used by emulators:
a19–a0
ao15–ao8
ad7–ad0
ale
bhe_n
aden_n (on the IA186ES)
clkouta
rfsh2_n/aden_n (on the IA188ES)
rd_n
s2_n–s0_n
s6/lock_n/clkdiv2_n
uzi_n
Emulators require that s6/lock_n/clkdiv2_n and uzi_n be configured as their normal functions
(i.e., as s6 and uzi_n, respectively). Holding bhe_n/aden_n (IA186ES) or rfsh_n/aden_n
(IA188ES) low during the rising edge of res_n, s6, and uzi_n will be configured at reset in their
normal functions instead of as PIOs.
3.
Maximum Ratings, Thermal Characteristics, and DC Parameters
For the Innovasic Semiconductor IA186ES and IA188ES microcontrollers, the absolute
maximum ratings, thermal characteristics, and DC parameters are provided in Tables 11
through 13, respectively.
Table 11. IA186ES and IA188ES Absolute Maximum Ratings
Parameter
Storage Temperature
Voltage on any Pin with Respect to vss
Rating
−65°C to +125°C
−0.5V to +(vcc + 0.5)V
Table 12. IA186ES and IA188ES Thermal Characteristics
Symbol
TA
Characteristic
Ambient Temperature
®
Value
-40°C to 85°C
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 45 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 13. DC Characteristics Over Commercial Operating Ranges
Symbol
VIL
VIL1
VIH
VIH1
VIH2
VOL
Parameter Description
Input Low Voltage (Except x1)
Clock Input Low Voltage (x1)
Input High Voltage (Except res_n
and x1)
Input High Voltage (res_n)
Clock Input High Voltage (x1)
Output Low Voltages
VOH
Output High Voltagesa
ICC
Power Supply Current @ 0 C
ILI
Input Leakage Current @ 0.5
MHz
Output Leakage Current @ 0.5
MHz
Clock Output Low
Clock Output High
ILO
VCLO
VCHO
Test Conditions
–
–
–
Preliminary
Min
Max
−0.5
0.8
−0.5
0.8
2.0
vcc +0.5
–
2.4
–
vcc–0.8
IOL = 2.5 mA (s2_n–s0_n)
–
IOL = 2.0 mA (other)
–
IOH = −2.4 mA @ 2.4 V
2.4
IOH = −200 A @ vcc −0.5 vcc −0.5
–
vcc = 5.5 Vb
0.45 V
VIN
0.45 V
VOUT
vcc
vcc c
ICLO = 4.0 mA
ICHO = −500 A
vcc +0.5
vcc +0.5
0.45
0.45
vcc +0.5
vcc
5.9
Unit
V
V
V
–
10
V
V
V
V
V
V
mA/
MHz
A
–
10
A
–
vcc −0.5
0.45
–
V
V
aThe lcs_n/once0_n, mcs3_n–mcs0_n, ucs_n/once1_n, and rd_n pins have weak internal pullup resistors. Loading
the lcs_n/once0_n and ucs_n/once1_n pins in excess of IOH = −200 A during reset can cause the device to go into
ONCE mode.
bCurrent is measured with the device in reset with the x1 and x2 driven and all other non-power pins open but held
high or low.
cTesting is performed with the pins floating, either during hold or by invoking the ONCE mode.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 46 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
4.
Data Sheet
November 15, 2011
Device Architecture
A functional block diagram of the IA186ES/IA188ES is shown in Figure 7. This microcontroller
consists of the following functional blocks.
Bus Interface and Control (BIC)
Chip Selects and Control (CSC)
Programmable I/O
Clock and Power Management
DMA
Interrupt Controller
Timers
Asynchronous Serial Ports (2).
4.1
Bus Interface and Control
The BIC manages all accesses to external memory and external peripherals. These peripherals
may be mapped either in memory space or I/O space. The BIC supports both multiplexed and
non-multiplexed bus operations. Multiplexed address and data are provided on the AD [15–0]
bus, while a non-multiplexed address is provided on the A [19–0] bus. The A bus provides
address information for the entire bus cycle (t1–t4), while the AD bus provides address
information only during the first (t1) phase of the bus cycle. For details regarding bus cycles, see
Chapter 6, AC Specifications.
The BIC provide the capability to dynamically alter the size of the data bus. By programming
the auxiliary control register (AUXCON), a user may easily support external peripherals and
memory devices of both 8- and 16-bit widths without specialized micro-code managing the data
accesses. The AUXCON register contains 3 programmable bits for this purpose: LSIZ, MSIZ,
and IOSIZ. For details regarding the operation of these bits, see Section 5.1, Control and
Registers. The IA186ES microcontroller provides two signals to support this functionality, write
high byte (whb_n) and write low byte (wlb_n). The IA188ES microcontroller requires only a
single write byte (wb_n) signal to support its 8-bit data bus.
The BIC also provides support for PSRAM devices. PSRAM is supported in the lower chip
select (lcs_n) area only. In order to support PSRAM, the CSC must be appropriately
programmed. For details regarding this operation, see Section 4.7, Chips Selects.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 47 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
gnd
vcc
s2_n–s0_n
Data Sheet
November 15, 2011
uzi_n
s6/lock_n/clkdiv2_n
hold
hlda
srdy
den_n/ds_n
ardy
dtr_n
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
a[19:0]
clkouta
Clock and Power
Management
ad[15:0]
ale
bhe_n/aden_n
wr_n
wlb_n
whb_n
rd_n
Bus Interface
and Control
clkoutb
drq0/int5
Direct Memory
Access
res_n
Interrupt
Controller
Peripheral
Control and
Registers
Pulse Width
(
) (PWD)
Demodulator
drq1/int6
int4
int3/inta1_n
int2/inta0_n
int1/select_n
int0
nmi
pwd
tmrin0
lcs_n/once0_n
mcs3_n/rfsh_n
ucs_n/once1_n
pcs5_n/a1
pcs6_n/a2
Timers
tmrout0
tmrin1
tmrout1
Chip Selects
and Control
txd0
Asynchronous
Serial Port 0
mcs2_n–mcs0_n
pcs3_n–pcs0_n
rxd0
cts0_n/enrx0_n
rts0_n/rtr0_n
txd1
pio[31:0]
Asynchronous
Serial Port 1
Programmable
I/O
rxd1
cts1_n/enrx1_n
rts1_n/rtr1_n
Instruction Decode
and Execution
Figure 7. Functional Block Diagram
Note: See pin descriptions for pins that share other functions with PIO pins.
Pins pwd, int5, int6, rts1_n/rtr1_n, and cts1_n/enrx1_n are multiplexed with
int2_n/inta0_n, drq0, drq0, pcs3_n, and pcs2_n, respectively.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 48 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
4.2
Data Sheet
November 15, 2011
Clock and Power Management
A phase-lock-loop (PLL) and a second programmable system clock output (clkoutb) are included
in the clock and power management unit. The internal clock is the same frequency as the crystal
but with a duty cycle of 45% to 55%, as a worst case, generated by the PLL obviating the need
for a 2X external clock. A POR resets the PLL (see Figure 8).
C1
x1
IA186ES/
IA188ES
C1 = 15 pF ±20%
C2 = 22 pF ±20%
x2
C2
Recommended
range of values for
C1 and C2 are:
Crystal
Figure 8. Crystal Configuration
4.3
System Clocks
If required, the internal oscillator may be driven by an external clock source that should be
connected to x1, leaving x2 unconnected.
The clock outputs, clkouta and clkoutb, may be enabled or disabled individually (SYSCON
register Bits [11–8]). These clock control bits allow one clock output to run at PLL frequency
and the other to run at the power-save frequency (see Figure 9).
Processor Internal Clock
x1, x2
Power-Save
Divisor
(/2 to /128)
PLL
Mux
clkouta
Drive enable
Mux
Time Delay
6 ±2.5nS
clkoutb
Drive enable
Figure 9. Organization of Clock
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 49 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
4.4
Data Sheet
November 15, 2011
Power-Save Mode
The operation of the CPU and peripheral operate at a slower clock frequency when in power save
mode, reducing power consumption and thermal dissipation. Should an interrupt occur, the
microcontroller returns to its normal operating frequency automatically on the internal clock’s
next rising edge in t3. Any clock-dependent devices should be reprogrammed for the change in
frequency during the power-save mode period.
4.5
Initialization and Reset
The res_n (Reset), the highest priority interrupt, must be held low for 1 mS during power-up to
initialize the microcontroller correctly. This operation makes the device cease all instruction
execution and local bus activity. The microcontoller begins instruction execution at physical
address FFFF0h when res_n becomes inactive and after an internal processing interval with
ucs_n is asserted and three wait states. Reset also sets up certain registers to predetermined
values and resets the WDT.
4.6
Reset Configuration Register
The data on the address/data bus (ad15–ad0 for the IA186ES and ao15–ao8 and ad7–ad0 for the
IA188ES) are written into the Reset Configuration Register when reset is low. This data is
system-dependent and is held in the Reset Configuration Register after reset is de-asserted. This
configuration data may be placed on the address/data bus by using weak external pull-up and
pull-down resistors or applied to the bus by an external driver, as the processor does not drive the
bus during reset. It is a method of supplying the software with some initial data after a reset
(e.g., option jumper positions).
4.7
Chip Selects
Chip-select generation is programmable for memories and peripherals. Programming is also
available to produce ready and wait-state generation plus latched address bits a1 and a2. For all
memory and I/O cycles, the chip-select lines are active within their programmed areas,
regardless of whether they are generated by the internal DMA unit or the CPU.
There are six chip-select outputs for memory and a further six for peripherals whether in memory
or I/O space. The memory chip-selects are able to address three memory ranges, whereas the
peripheral chip-selects are used to address 256-byte blocks that are offset from a programmable
base address. Writing to a chip-select register enables the related logic even in the event that the
pin in question has another function (e.g., where a pin is programmed to be a PIO).
4.8
Chip-Select Timing
For normal timing, the ucs_n and lcs_n outputs are asserted with the non-multiplexed address
bus.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 50 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
4.9
Data Sheet
November 15, 2011
Ready- and Wait-State Programming
Each of the memory or peripheral chip-select lines can have a ready signal programmed that can
be the ardy or srdy signal. The chip-select control registers (UMCS, LMCS, MMCS, PACS, and
MPCS) have a single bit that selects if the external ready signal is to be used or not (R2, Bit [2]).
R1 and R0 (Bits [1–0]) in these registers control the number of wait states that are inserted
during each access to a memory or peripheral location (from 0 to 3). The control registers for
pcs3_n–pcs0_n use three bits, R3, R1–R0 (Bit [3] and Bits [1–0]) to provide 5, 7, 9, and 15 wait
states in addition to the original values of 0–3 wait states.
When an external ready has been selected as required, internally programmed wait states will
always be completed before the external ready can finish or extend a bus cycle. Consider a
system in which the number of wait states to be inserted has been set to three. The external
ready pin is sampled by the processor during the first wait cycle. If the ready is asserted, the
access is completed after seven cycles (4 cycles plus 3 wait cycles). If the ready is not asserted,
during the first wait cycle the access is prolonged until ready is asserted and two more wait states
are inserted followed by t4. The ardy signal is an asynchronous ready with a pin that is active
high and accepts a rising edge asynchronous to clkouta. However, an additional clock period
may be necessary if the falling edge of ardy is not synchronized to clkouta.
4.10
Chip-Select Overlap
Overlapping chip selects are those configurations in which more than one chip select is asserted
for the same physical address. If PCS is configured in I/O space with LCS or any other chip
select configured for memory, address 00000h is not overlapping the chip selects.
It is not recommended that multiple chip-select signals be asserted for the same physical address,
although it may be unavoidable in certain systems. If this is the case, all overlapping chip selects
must have the same external ready configuration and the same number of wait states to be
inserted into access cycles.
Internal signals are employed to access the peripheral control block (PCB). These signals serve
as chip selects that are configured with no wait states and no external ready. Only when these
chip selects are configured in the same manner can the PCB be programmed with addresses that
overlap external chip selects.
Care should be exercised in the use of the DA bit in the LMCS or UMCS registers when
overlapping an additional chip select with either the lcs_n or ucs_n chip selects. Setting the DA
bit to “1” prevents the address from being driven onto the AD bus for all accesses for which the
respective chip select is active, including those for which the multiple selects are active.
The mcs_n and pcs_n pins are dual-purpose pins, either as chip selects or PIO inputs or outputs.
However, their respective ready- and wait-state configurations for their chip-select function will
be in effect regardless of the function for which they are actually programmed. Their ready- and
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 51 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
wait-state settings must agree with those for any overlapping chip selects as though they had
been configured as chip selects. This is true regardless of whether these pins are configured as
PIO and enabled (by writing to the MMCS and MPCS registers for the mcs_n chip selects and to
the PACS and MPCS registers for the pcs_n chip selects).
Even though pcs4_n is not available as an external pin, it has ready- and wait-state logic and
must therefore follow the rules for overlapping chip selects. By contrast, the pcs6_n and pcs5_n
have ready and wait-state logic that is disabled when they are configured as address bits a2
and a1, respectively.
If the chip-select-configuration rules are not followed, the processor may hang with the
appearance of waiting for a ready signal—even in a system where ready (ardy or srdy) is always
set to “1.”
4.11
Upper-Memory Chip Select
The ucs_n chip select is for the top of memory. On reset, the microcontroller begins fetching
and executing instructions at memory location FFFF0h, so upper memory is usually used for
instruction. To this end, ucs_n is active on reset and has a memory range of 64 Kbytes (F0000h
to FFFFFh) as default, along with external ready required and three wait states automatically
inserted. The lower boundary of ucs_n is programmable to provide ranges of 64 to 512 Kbytes.
4.12
Low-Memory Chip Select
The lcs_n chip select is for lower memory and may be configured for 8- or 16-bit accesses by the
AUXCON register. Because the interrupt vector table is at the bottom of memory beginning at
00000h, this pin is usually used for control data memory. Unlike ucs_n, this pin is inactive on
reset.
4.13
Midrange-Memory Chip Selects
There are four midrange chip selects, mcs3_n–mcs0_n, which may be used in a user-located
memory block. With some exceptions, the base address of the memory block may be located
anywhere in the 1-Mbyte memory address space. The memory spaces used by the ucs_n and
lcs_n chip selects are excluded, as are pcs6_n, pcs5_n, and pcs3_n–pcs0_n. If the pcs_n chip
selects are mapped to I/O space, the MCS address range can overlap the PCS address range.
The mcs0_n chip select may be programmed to be active over the entire MCS range, leaving the
mcs3_n–mcs1_n free for use as PIO pins.
The MCS may be configured for 8- or 16-bit accesses by the AUXCON register. The width of
the non-UCS/non-LCS memory ranges determines the MCS range bus width. The assertion of
the MCS outputs occurs with the same timing as the multiplexed AD address bus.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 52 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
4.14
Data Sheet
November 15, 2011
Peripheral Chip Selects
There are six peripheral chip selects, pcs6_n, pcs5_n, and pcs3_n–pcs0_n, which may be used
within a user-defined memory or I/O block. Except for the spaces associated with the ucs_n,
lcs_n, and mcs_n chip selects, the base address can be located anywhere within the 1-Mbyte
memory-address space or programmed to the 64-Kbyte I/O space. The pcs4_n is not available.
None of the pcs_n pins are active at reset. The pcs6_n–pcs5_n and pcs3_n–pcs0_n may be
programmed to have 0 to 3 wait states. The pcs3_n–pcs0_n may be also programmed to have
5, 7, 9, and 15 wait states.
The PCS may be configured for 8- or 16-bit accesses by the AUXCON register. The PCS range
bus width is determined either by that of the non-UCS/non-LCS memory range or by the width
of the I/O space. The assertion of the PCS outputs occurs with the same timing as the
multiplexed AD address bus. Each of the PCS operates over a 256-byte address range.
4.15
Refresh Control
The Refresh Control Unit (RCU) automatically generates refresh bus cycles with a fixed waitstate value of three for the PSRAM automatic refresh mode. The RCU generates a memory-read
request after a programmable period of time to the bus interface unit.
The ENA bit in the Enable RCU register (EDRAM) enables refresh cycles, operating off the
processor internal clock. If the processor is in power-save mode, the RCU must be reconfigured
for the new clock rate.
If the hlda pin is asserted when a refresh request is initiated (indicating a bus-hold condition), the
processor disables the hlda pin to allow a refresh cycle to be performed. The external circuit bus
master must deassert the hold signal for at least one clock period to permit the execution of the
refresh cycle.
4.16
Interrupt Control
Interrupt requests originate from a variety of internal and external sources that are arranged in
priority order by the internal interrupt controller and are presented sequentially to the processor.
Eight external-interrupt sources are connected to the processor. These include seven maskable
and one nonmaskable interrupt (NMI). Eight internal-interrupt sources are also connected to the
processor. These include those not brought out to external pins—three timers, two DMA
channels, two asynchronous serial ports, and the WDT NMI. Interrupts int6 and int5
(multiplexed with drq1 and drq0) are available if the respective DMA is not enabled or is
internally synchronized.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 53 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
With the exception of int0, the seven external maskable interrupt request pins are
multifunctional. One function is for direct-interrupt requests. The int6 and int5 are edgetriggered. The int4–int0 may be either level- or edge-triggered.
When configured in cascade mode, int1 and int0 interface with an external 82C59A-type
interrupt controller. When int0 is configured for cascade mode, the function of int2 is
automatically switched to its inta0_n role. Similarly, when int1 is configured for cascade mode,
int3 is switched to its inta1_n role. An external 82C59A-compatible interrupt controller may be
used as the system master by programming the internal interrupt controller to slave mode, but
int6–int4 cannot be used.
Although other interrupts are disabled when another is accepted, these may be re-enabled by
setting the Interrupt Enable Flag (IF) in the Processor Status Flags register during the Interrupt
Service Routine (ISR). Setting IF permits interrupts of equal or greater priority to interrupt the
currently running ISR.
Further interrupts from the same source will be blocked until the corresponding bit in the InService (INSERV) register is cleared. When set to 1, the Special Fully Nested mode (SFNM) is
invoked for int0 and int1 in the INT0 and INT1 Control registers, respectively. In this mode, a
new interrupt may be generated by these sources regardless of the in-service bit. The following
table shows the priorities of the interrupts at POR.
4.17
Interrupt Types
Table 14 presents interrupt names, types, vector table address, End-of-Interrupt (EOI) type,
overall priority, and related instructions.
Table 14. Interrupt Types
Interrupt Name
Divide Error Exceptiona
Trace Interruptb
Non-maskable Interrupt (NMI)
Breakpoint Interrupta
INT0 Detected Overflow Exceptionb
Array Bounds Exceptiona
Unused Opcode Exceptiona
ESC Opcode Exceptiona,b
Timer0 Interruptd,e
Timer1 Interruptd,e
®
Interrupt
Type
00h
01h
02h
03h
04h
05h
06h
Vector
Table
Address
00h
04h
08h
0ch
10h
14h
18h
EOI
Type
NA
NA
NA
NA
NA
NA
NA
Overall
Priority
1
1A
1B
1
1
1
1
07h
08h
12h
1ch
20h
48h
NA
08h
08h
1
2A
2B
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 54 of 154
Related
Instructions
DIV, IDIV
All
–
INT3
INT0
BOUND
Undefined
Opcodes
ESC Opcodes
–
–
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 14. Interrupt Types (Continued)
Interrupt Name
Timer2 Interruptd,e
Reserved
DMA0 Interrupt/INT5e
DMA1 Interrupt/INT6e
INT0 Interrupt
INT1 Interrupt
INT2 Interrupt
INT3 Interrupt
INT4 Interruptf
Asynchronous Serial Port 1 Interfacef
Asynchronous Serial Port 0 Interfacef
Reserved
Interrupt
Type
13h
09h
0ah
0bh
0ch
0dh
0eh
0fh
10h
11h
14h
15h–1fh
Vector
Table
Address
4ch
24h
28h
2ch
30h
34h
38h
3ch
40h
44h
50h
54h–7ch
EOI
Type
08h
Overall
Priority
2C
Related
Instructions
–
–
–
0ah
0bh
0ch
0dh
0eh
0fh
10h
11h
14h
3
4
5
6
7
8
9
9
9
–
–
–
–
–
–
–
–
–
–
–
–
–
Note: If the priority levels are not changed, the default priority level will be used for the interrupt sources.
aInstruction execution generates interrupts.
bPerformed in the same manner as for the 8086 and 8088.
cAn ESC opcode causes a trap.
dBecause only one IRQ is generated for the three timers, they share priority level with other sources. The
timers have an interrupt priority order among themselves (2A > 2B > 2C).
eThese interrupt types are programmable in slave mode.
fNot available in slave mode.
4.18
Timer Control
The IA186ES and IA188ES have a WDT and three 16-bit programmable timers. Timer0 and
timer1 each has an input and output connected to external pins that permits it to count or time
events as well as produce variable duty-cycle waveforms or non-repetitive waveforms. These
same timers are used to measure the high- and low-pulse widths of the Pulse Width Demodulator
on the pwd pin.
Because timer2 does not have external connections, it is confined to internal functions such as
real-time coding, time-delay applications, a prescaler for timer0 and timer1, or to synchronize
DMA transfers.
The Peripheral Control Block contains eleven 16-bit registers to control the programmable
timers. Each timer-count register holds the present value of its associated timer and may be read
from or written to whether the timer is in operation or not. The microcontroller increments the
value of the timer-count register when a timer event takes place.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 55 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
The value stored in a timer’s associated maximum count register determines its maximum count
value. Upon reaching it, the timer count register is reset to 0 in the same clock cycle that this
count was attained. The timer count register does not store this maximum value. Both timer0
and timer1 have a primary and a secondary maximum count register that permits each to
alternate between two discrete maximum values.
Timer0 and timer1 may have the maximum count registers configured in either primary only or
both primary and secondary. If the primary only is configured to operate, on reaching the
maximum count, the output pin will go low for one clock period. If both the primary and
secondary registers are enabled, the output pin reflects the state of the register in control at the
time. This generates the required waveform that is dependent on the two values in the maximum
count registers.
Because they are polled every fourth clock period, the timers can operate at a quarter of the
internal clock frequency. Although an external clock may be used, the timer output may take six
clock cycles to respond to the input.
4.19
Watchdog Timer
The WDT operates in real WDT fashion and may be used to prevent loss of control in the event
that software does not respond in an expected manner. The WDT is active after reset, has a
maximum timeout count, and is programmed for system reset mode. The WDT control register
(WDTCON) may be written to only once after reset. This is accomplished by writing 3333h,
then CCCCh followed by the new configuration data to the WDTCON register. Provided they
do not include access to the WDTCON register, any number of operations may be performed
between these two words, including memory and I/O reads and writes.
Writing AAAAh then 5555h to the WDTCON register resets the current count. This count
cannot be read. Provided they do not include access to the WDTCON register, any number of
operations may be performed between these two words, including memory and I/O reads and
writes. Use of these sequences is intended to prevent executing code from blocking a WDT
event. With the WDT, a maximum 1.67-second timeout period is possible in a 40-MHz system.
The WDT can be programmed to generate either an NMI or a system reset when it times out. If
programmed to generate an NMI, the NMIFLAG (Bit [12]) in the WDTCON register will be set
when it occurs. This flag should be tested by the NMI interrupt service routine (ISR) to establish
whether the WDT or an external source generated the interrupt. If set by writing the 3333h and
CCCCh sequence followed by the configuration data that includes clearing NMIFLAG, the ISR
should clear this flag. If the NMIFLAG is set while a second WDT timeout occurs, a WDT
system reset is generated in place of a second NMI interrupt.
The RSTFLAG (Bit [13]) in the WDTCON register is set if a WDT reset is generated, due to one
WDT occurrence while the WDT is programmed to generate resets, or because a WDT event
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 56 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
occurred with the NMIFLAG set. This permits system initialization code to distinguish between
a WDT reset and hardware reset and take appropriate action. The RSTFLAG is cleared by a read
or write to the WDTCON register. During a WDT reset, the external pins are not re-sampled,
ensuring that clocking, reset configuration register, and any other features that are user
programmable during reset do not change when a WDT system reset occurs. All other activities
are the same as those of a normal system reset.
4.20
Direct Memory Access
DMA frees the CPU from involvement in transferring data between memory and peripherals
over either one or both high-speed DMA channels. Data may be transferred from memory to
I/O, I/O to memory, memory to memory, or I/O to I/O. DMA channels may be connected to
asynchronous serial ports.
The IA186ES microcontroller supports the transfer of both bytes and words to and from even or
odd addresses. It does not support word transfers to memory that is configured for byte accesses.
The IA188ES does not support word transfers at all. Each data transfer will take two bus cycles
(a minimum of 8 clock cycles).
There are four sources of DMA requests for both DMA channels:
The channel request pin (drq1–drq0)
Timer2
A serial port
The system software.
Each channel may be programmed to have a different priority either to resolve a simultaneous
DMA request or to interrupt a transfer on the other channel.
4.21
DMA Operation
The PCB contains six registers for each DMA channel to control and specify the operation of the
channel (see Figure 10):
Two registers to store a 20-bit source address
Two registers to store a 20-bit destination address
One 16-bit transfer-count register
One 16-bit control register
The number of DMA transfers required is designated in the DMA Transfer Count register and
may contain up to 64 Kbytes or words. It will end automatically. DMA channel function is
defined by the Control registers. Like the other five registers, these may be changed at any time
(including during a DMA transfer) and are implemented immediately.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 57 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
20-bit Adder/Subtractor
Data Sheet
November 15, 2011
Adder
Control Logic
Timer Request
20
Request
Selection
Logic
Transfer Counter Ch. 1
Destination Address Ch. 1
Source Address Ch. 1
Transfer Counter Ch. 0
drq1
drq0
DMA
Control
Logic
Interrupt Request
Destination Address Ch. 0
Source Address Ch. 0
Channel Control Register 1
20
Channel Control Register 0
16
Internal Address/Data Bus
Figure 10. DMA Unit
4.22
DMA Channel Control Registers
See Section 5.1.10, D1CON (0dah) and D0CON (0cah). The DMA channel control registers
specify the following:
Whether the data destination is in memory or I/O space (Bit [15])
Whether the destination address is incremented, decremented, or unchanged after each
transfer (Bits [14–13])
Whether the data source is in memory or I/O space (Bit [12])
Whether the source address is incremented, decremented, or unchanged after each
transfer (Bits [11–10])
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 58 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Whether DMA transfers cease upon reaching a designated count (Bit [9])
Whether the last transfer generates an interrupt (Bit [8])
Synchronization mode (Bits [7–6])
The relative priority of one DMA channel with respect to the other (Bit [5])
Acceptance of DMA requests from Timer2 (Bit [4])
Configuration of DRQ pins as INT (Bit [3])
Byte or Word transfers (Bit [0])
4.23
DMA Priority
With the exception of word accesses to odd memory locations or between locked memory
addresses, DMA transfers have a higher priority than CPU transfers. Because the CPU cannot
access memory during a DMA transfer and a DMA transfer cannot be suspended by an interrupt
request, continuous DMA activity will increase interrupt delay. An NMI request halts any DMA
activity, however, enabling the CPU to respond promptly to the request.
4.24
Pulse Width Demodulation
Note: There is no support for analog-to-digital conversion. This feature
provides a means of measuring the width of a pulse in both its high and low
phases. Its enabled by the PWD bit (Bit [6]) in the SYSCON.
TMRIN0, TMRIN1, INT2, and INT4 are internally configured to support the detection of rising
and falling edges on the PWD pin (int2/int0_n/pwd) and to enable either timer0 or timer1,
depending on whether the signal is high or low (see Figure 11). Because they are not used in this
mode, the tmrin0, tmrin1, and int4 pins are available as PIO pins.
int2
int4
int2
Interrupts generated
timer1 enabled
timer0 enabled
Figure 11. Typical Waveform at the int2/int0_n/pwd pin
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 59 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
The current count of timer1 for INT2 and timer0 for INT4 should be inspected by the ISR to
determine the pulse width. The timer count register should then be reset by the ISR in readiness
for the next pulse.
The timer count rate (one-fourth of the processor clock rate) determines the maximum resolution
of the timers. To avoid the delay in servicing a timer interrupt in cases where the pulse width is
short, the INT2 and INT4 request bits in the Interrupt Request register may be polled. In cases
where the pulse width is greater than the maximum count of the timer, detection is achieved
either by monitoring the Maximum Count (MC) bit of the respective timer or by enabling the
timer interrupt requests by setting the INT bit in the respective Timer Mode and Control
Register.
4.25
Asynchronous Serial Ports
There are two independent asynchronous serial ports that employ standard industry
communication protocols in their implementation of full duplex, bi-directional data transfers.
Functioning independently, either port may be the source or destination of DMA transfers.
The following features are supported:
Full-duplex data transfers
7-, 8-, or 9-bit data transfers
Odd, even, or no parity
One or two stop bits
Break characters of two lengths
Error detection provided by parity, framing, or overrun errors
Hardware handshaking achieved with the following selectable control signals:
– Clear to send (cts_n)
– Enable receiver request (enrx_n)
– Ready to send (rts_n)
– Ready to receive (rtr_n)
DMA to and from the ports
Each port has its own maskable interrupts
9-bit multidrop protocol
Each port has an independent baud-rate generator
Maximum baud rate is 1/16 of the processor clock
Transmit and receive lines are double buffered
4.26
Programmable I/O
Thirty-two pins are programmable as I/O signals (PIO). Table 15 presents them in both numeric
and alphabetic order. Because programming a pin as a PIO disables its normal function, it
should be done only if the normal function is not required. A PIO pin can be programmed as an
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 60 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
input or output with or without a weak pull-up or pull-down. A PIO pin can be also programmed
as an open-drain output. Each PIO pin regains default status after a POR.
Table 15. Default Status of PIO Pins at Reset
PIO
No.
0
1
2
3
4
5
6
7b
8b
9b
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26b,c
27
28
29b,c
30
31
Associated Pin
tmrin1
tmrout1
pcs6_n/a2
pcs5_n/a1
dt/r_n
den_n/ds_n
srdy
a17
a18
a19
tmrout0
tmrin0
drq0/int5
drq1/int6
mcs0_n
mcs1_n
pcs0_n
pcs1_n
pcs2_n/cts1_n/enrx1_n
pcs3_n/rts1_n/rtr1_n
rts0_n/rtr0_n
cts0_n/enrx0_n
txd0
rxd0
mcs2_n
mcs3_n/rfsh_n
uzi_n
txd1
rxd1
s6/lock_n/clkdiv2
int4
int2/inta0_n/pwd
Power-On Reset
Status
Input with pullup
Input with pulldown
Input with pullup
Normal operationa
Normal operationa
Normal operationa
Normal operationa
Normal operationa
Normal operationa
Normal operationa
Input with pulldown
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Associated Pin
a17
a18
a19
cts0_n/enrx0_n
den_n/ds_n
drq0/int5
drq1/int6
dt/r_n
int2/inta0_n/pwd
int4
mcs0_n
mcs1_n
mcs2_n
mcs3_n/rfsh_n
pcs0_n
pcs1_n
pcs2_n/cts1_n/enrx1_n
pcs3_n/rts1_n/rtr1_n
pcs5_n/a1
pcs6_n/a2
rts0_n/rtr0_n
rxd0
rxd1
s6/lock_n/clkdiv2
srdy
timrin0
tmrin1
tmrout0
tmrout1
txd0
txd1
uzi_n
A
7
8
9
21
5
12
13
4
31
30
14
16
24
25
16
17
18
19
3
2
20
23
28
29
6
11
0
10
1
22
27
26
Power-On Reset
Status
Normal operationa
Normal operationa
Normal operationa
Input with pullup
Normal operationa
Input with pullup
Input with pullup
Normal operationa
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Input with pullup
Normal operationd
Input with pullup
Input with pullup
Input with pulldown
Input with pulldown
Input with pullup
Input with pullup
Input with pullup
aInput with pullup when used as PIO.
bEmulators use these pins and also s2_n–s0_n, res_n, nmi, clkouta, bhe_n, ale, ad15–ad0, and a16–a0.
cIf bhe_n/aden_n (IA186ES) or rfsh_n/aden_n (IA188ES) is held low during POR, these pins will revert to normal
operation.
dInput with pulldown option available when used as PIO.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 61 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
These default status settings may be changed as desired.
After POR, a19–a17, the three most significant bits of the address bus, start with their normal
function, allowing the processor to begin fetching instructions from the boot address FFFF0h.
Normal function is also the default setting for dt/r_n, den_n, and srdy after POR.
If the ad15–ad0 bus override is enabled, s6/clkdiv2_n and uzi_n automatically return to normal
operation. The ad15–ad0 bus override is enabled if either the bhe_n/aden_n for the IA186ES or
the rfsh2_n/aden_n for the IA188ES is held low during POR.
5.
Peripheral Architecture
5.1
Control and Registers
The on-chip peripherals in the IA186ES/IA188ES are controlled from a 256-byte block of
internal registers. Although these registers are actually located in the peripherals they control,
they are addressed within a single 256-byte block of I/O space and are treated as a functional
unit. A list of these registers is presented in Table 16.
Although a named register may be 8 bits, write operations performed on the IA188ES should be
8-bit writes, resulting in 16-bit data transfers to the Peripheral Control Block (PCB) register.
Only word reads should be performed to the PCB registers. If unaligned read and write accesses
are performed on either the IA186ES or IA188ES, indeterminate behavior may result.
Note: Adhere to these directions while writing code to avoid errors.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 62 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 16. Peripheral Control Registers
Register Name
Peripheral Control Block Registers
PCB Relocation Register
Reset Configuration Register
Processor Release Level Register
Auxiliary Configuration Register
System Configuration Register
Watchdog Timer Control Register
Enable RCU Register
Clock Prescaler Register
Memory Partition Register
DMA Registers
DMA1 Control Register
DMA1 Transfer Count Register
DMA1 Destination Address High Register
DMA1 Destination Address Low Register
DMA1 Source Address High Register
DMA1 Source Address Low Register
DMA0 Control Register
DMA0 Transfer Count Register
DMA0 Destination Address High Register
DMA0 Destination Address Low Register
DMA0 Source Address High Register
DMA0 Source Address Low Register
Chip-Select Registers
pcs_n and mcs_n Auxiliary Register
Mid-Range Memory Chip-Select Register
Peripheral Chip-Select Register
Low-Memory Chip-Select Register
Upper-Memory Chip-Select Register
Serial Port 0 Registers
Serial Port 0 Baud Rate Divisor Register
Serial Port 0 Receive Register
Serial Port 0 Transmit Register
Serial Port 0 Status Register
Serial Port 0 Control Register
PIO Registers
PIO Data 1 Register
PIO Direction Register
PIO Mode 1 Register
PIO Data 0 Register
PIO Direction 0 Register
PIO Mode 0 Register
®
Offset
FEh
F6h
F4h
F2h
F0h
E6h
E4h
E2h
E0h
DAh
D8h
D6h
D4h
D2h
D1h
CAh
C8h
C6h
C4h
C2h
C0h
A8h
A6h
A4h
A2h
A0h
88h
86h
84h
82h
80h
7Ah
78h
76h
74h
72h
70h
Register Name
Timer Registers
Timer2 Mode and Control Register
Timer2 Max Count Compare A Register
Timer2 Count Register
Timer1 Mode and Control Register
Timer1 Max Count Compare B Register
Timer1 Max Count Compare A Register
Timer1 Count Register
Timer0 Mode and Control Register
Timer0 Max Count Compare B Register
Timer0 Max Count Compare A Register
Timer0 Count Register
Interrupt Registers
Serial Port 0 Interrupt Control Register
Serial Port 1 Interrupt Control Register
INT4 Interrupt Control Register
INT3 Interrupt Control Register
INT2 Interrupt Control Register
INT1 Interrupt Control Register
INT0 Interrupt Control Register
DMA1/INT6 Interrupt Control Register
DMA0/INT5 Interrupt Control Register
Timer Interrupt Control Register
Interrupt Status Register
Interrupt Request Register
Interrupt In-Service Register
Interrupt Priority Mask Register
Interrupt Mask Register
Interrupt Poll Status Register
Interrupt Poll Register
End-of-Interrupt (EOI) Register
Interrupt Vector Register
Serial Port 1 Registers
Serial Port 1 Baud Rate Divisor Register
Serial Port 1 Receive Register
Serial Port 1 Transmit Register
Serial Port 1 Status Register
Serial Port 1 Control Register
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 63 of 154
Offset
66h
62h
60h
5Eh
5Ch
5Ah
58h
56h
54h
52h
50h
44h
42h
40h
3Eh
3Ch
3Ah
38h
36h
34h
32h
30h
2Eh
2Ch
2Ah
28h
26h
24h
22h
20h
18h
16h
14h
12h
10h
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
5.1.1
Data Sheet
November 15, 2011
RELREG (0feh)
The Peripheral Control Block RELocation REGister maps the entire Peripheral Control Block
Register Bank to either I/O or memory space. In addition, RELREG contains a bit that places
the interrupt controller in either master or slave mode. The RELREG contains 20ffh at reset (see
Table 17).
Table 17. Peripheral Control Block Relocation Register
15
Reserved
14
S/Mn
13
Reserved
12
IO/Mn
11
10
9
8
7 6 5 4
RA [19–8]
3
2
1
0
Bit [15]—Reserved.
Bit [14]—S/Mn → When set to 1, this bit places the interrupt controller into slave mode.
When 0, it is in master mode.
Bit [13]—Reserved.
Bit [12]—IO/Mn → When set to 1, the Peripheral Control Block is mapped into memory
space. When 0, this bit maps the Peripheral Control Block Register Bank into IO space.
Bits [11–0]—RA [19–8] → Sets the base address (upper 12 bits) of the Peripheral
Control Block Register Bank. RA [7–0] default to zero. When Bit [12] (IO/Mn) is set
to 1, RA [19–16] are ignored.
5.1.2
RESCON (0f6h)
The RESet CONfiguration Register latches user-defined information present at specified pins at
the rising edge of reset. The contents of this register are read-only and remain valid until the
next reset. The RESCON contains user-defined information at reset (see Table 18).
Table 18. Reset Configuration Register
15
14
13
12
11
10
9 8 7
RC [15–0]
6
5
4
3
2
1
0
Bits [15–0]—RC [15–0] → At the rising edge of reset, the values of specified pins
(ad15–ad0 for the IA186ES and ao15–ao8 and ad7–ad0 for the IA188ES) are latched into
this register.
5.1.3
PRL (0f4h)
The Processor Release Level Register contains a code corresponding to the latest processor
production release. The PRL is a read-only register. The PRL contains 1100h (see Table 19).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 64 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 19. Processor Release Level Register
15
14
13
12 11
PRL [7–0]
10
9
8
7
6
5
4 3
RES
2
1
0
Bits [15–8]—PRL [7–0] → The latest Processor Release Level.
PRL Value
10h
11h
12h
13h
14h
Processor
Release Level
A
B
C
D
E
Bits [7–0]—Reserved.
5.1.4
AUXCON (0f2h)
The AUXiliary CONfiguration Register configures the flow control signals for the asynchronous
serial ports. AUXCON controls data bus width (8- or 16-bit) for lower memory, middle
memory, and IO accesses and contains 0000h at reset (see Table 20).
Table 20. Auxiliary Configuration Register
15
14
13
12 11
RES
10
9
8
7
6
ENRX1
5
RTS1
4
ENRX0
3
RTS0
2
LSIZ
1
MSIZ
0
IOSIZ
Bit [15–7]—Reserved.
Bit [6]—ENRX1 → When set to 1, the cts1_n/enrx1_n pin functions as cts1_n. When 0,
it functions as enrx1_n.
Bit [5]—RTS1 → When set to 1, the rtr1_n/rts1_n pin functions as rts1_n. When 0, it
functions as rtr1_n.
Bit [4]—ENRX0 → When set to 1, the cts0_n/enrx0_n pin functions as cts0_n. When 0,
it functions as enrx0_n.
Bit [3]—RTS0 → When set to 1, the rtr0_n/rts0_n pin functions as rts0_n. When 0, it
functions as rtr0_n.
Bit [2]—LSIZ (IA186ES only) → When set to 1, 8-bit data accesses are performed in
lower chip-select (lcs_n) space. When 0, 16-bit data accesses are performed.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 65 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [1]—MSIZ (IA186ES only) → When set to 1, 8-bit data accesses are performed in
middle chip-select (mcs_n) space and peripheral chip-select space (psc_n—but only if
pcs_n is mapped to memory). When 0, 16-bit data accesses are performed.
Bit [0]—IOSIZ (IA186ES only) → When set to 1, 8-bit data accesses are performed in all
I/O space. When 0, 16-bit data accesses are performed.
5.1.5
SYSCON (0f0h)
The SYStem CONfiguration Register controls several miscellaneous system I/O and timing
functions. The SYSCON contains 0000h at reset (see Table 21).
Table 21. System Configuration Register
15
PSEN
14
MCSBIT
13
DSDEN
12
PWD
11
CBF
10
CBD
9
CAF
8
CAD
7
6
5 4
RES
3
2
F2
1
F1
0
F0
Bit [15]—PSEN → When set to 1, enables the power-save mode causing the internal
operating clock to be divided by the value in F2–F0. External or internal interrupts clear
PSEN automatically. Software interrupts and exceptions do not.
Note: The value of PSEN is not restored upon execution of an IRET
instruction.
Bit [14]—MCSBIT → When set to 1, mcs0_n is active over the entire MCS range, thus
freeing msc2 _n and mcs1_n to be used as PIO. When 0, it behaves normally.
Bit [13]—DSDEN → When set to 1, the ds_n/den_n pin functions as ds_n. When 0, it
functions as den_n. See the individual pin descriptions for details of data strobe (ds_n)
mode versus data enable (den_n) mode.
Bit [12]—PWD → When set to 1, the pulse width demodulator is enabled. When 0, it is
disabled.
Bit [11]—CBF → When set to 1, the clkoutb output follows the input crystal (PLL)
frequency. When 0, it follows the internal clock frequency after the clock divider.
Bit [10]—CBD → When set to 1, the clkoutb output is driven low. When 0, it is driven
as an output per the CBF bit.
Bit [9]—CAF → When set to 1, the clkouta output follows the input crystal (PLL)
frequency. When 0, it follows the internal clock frequency after the clock divider.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 66 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [8]—CAD → When set to 1, the clkouta output is driven low. When 0, it is driven as
an output per the CBF bit.
Bits [7–3]—Reserved → The bits read back as zeros.
Bits [2–0]—F2–F0 → These bits control the clock divider as shown below.
Note: PSEN must be 1 for the clock divider to function.
F2
0
0
0
0
1
1
1
1
5.1.6
F1
0
0
1
1
0
0
1
1
F0
0
1
0
1
0
1
0
1
Divider Factor
0
Divide by 1 (2 )
1
Divide by 2 (2 )
2
Divide by 4 (2 )
3
Divide by 8 (2 )
4
Divide by 16 (2 )
5
Divide by 32 (2 )
6
Divide by 64 (2 )
7
Divide by 128 (2 )
WDTCON (0e6h)
The WatchDog Timer CONtrol Register provides control and status for the WDT. The
WDTCON contains c080h at reset (see Table 22).
Table 22. Watchdog Timer Control Register
15
ENA
14
WRST
13
RSTFLAG
12
NMIFLAG
11
TEST
10
9 8
RES
7
6
5
4 3 2
COUNT
1
0
Bit [15]—ENA → When set to 1, the WDT is enabled. When 0, it is disabled.
Bit [14]—WRST → When set to 1, an internal WDT reset is generated when the WDT
timeout count (COUNT) is reached. When 0, an NMI will be generated once WDT
timeout count is reached and the NMIFLAG bit is 0. If the NMIFLAG bit is 1, an
internal WDT reset is generated when the WDT timeout count is reached.
Bit [13]—RSTFLAG → When set to 1, a WDT timeout event has occurred. This bit may
be cleared by software or by an external reset.
Bit [12]—NMIFLAG → When set to 1, a WDT NMI event has occurred. This bit may
be cleared by software or by an external reset. If this bit is 1 when WDT timeout occurs,
an internal WDT reset is generated regardless of the state of WRST.
Bit [11]—TEST → This bit is reserved for chip test and should be always set to 0.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 67 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bits [10–8]—Reserved.
Bits [7–0]—COUNT → Control the timeout period for the WDT as follows:
Ttimeout = 2
exponent
/frequency
(Equation 1)
Where:
Ttimeout
frequency
exponent
Bit [7]
0
X
X
X
X
X
X
X
1
5.1.7
= The WDT timeout period in seconds.
= The processor frequency in hertz.
= Is based upon count as shown below:
Bit [6]
0
X
X
X
X
X
X
1
0
Bit [5]
0
X
X
X
X
X
1
0
0
Bit [4]
0
X
X
X
X
1
0
0
0
Bit [3]
0
X
X
X
1
0
0
0
0
Bit [2]
0
X
X
1
0
0
0
0
0
Bit [1]
0
X
1
0
0
0
0
0
0
Bit [0]
0
1
0
0
0
0
0
0
0
Exponent
NA
10
20
21
22
23
24
25
26
EDRAM (0e4h)
The Enable Dynamic RAM Refresh Control Register provides control and status for the refresh
counter. The EDRAM register contains 0000h at reset (see Table 23).
Table 23. Enable Dynamic RAM Refresh Control Register
15
EN
14
0
13
0
12
0
11
0
10
0
9
0
8
7
6
5 4 3
T [8–0]
2
1
0
Bit [15]—EN → When set to 1, the refresh counter is enabled and msc3_n is configured
to act as rfsh_n. Clearing EN clears the refresh counter and disables refresh requests.
The refresh address is unaffected by clearing EN.
Bits [14–9]—Reserved → These bits read back as 0.
Bits [8–0]—T [8–0] → These bits hold the current value of the refresh counter. These
bits are read-only.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 68 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
5.1.8
Data Sheet
November 15, 2011
CDRAM (0e2h)
The Count for Dynamic RAM (CDRAM) Refresh Control Register determines the period
between refresh cycles. The CDRAM register is undefined at reset (see Table 24).
Table 24. Count for Dynamic RAM Refresh Control Register
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
7
6
5 4 3
RC [8–0]
2
1
0
Bits [15–9]—Reserved → These bits read back as 0.
Bits [8–0]—RC [8–0] → These bits hold the clock count interval between refresh cycles.
In power-save mode, the refresh counter value should be adjusted to account for the clock
divider value in SYSCON.
5.1.9
MDRAM (0e0h)
The Memory Partition for Dynamic RAM (MDRAM) Refresh Control Register holds the a19–
a13 address bits of the 20-bit base refresh address. The MDRAM register contains 0000h at
reset (see Table 25).
Table 25. Memory Partition for Dynamic RAM Refresh Control Register
15
14
13 12 11
M [6–0]
10
9
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Bits [15–9]—M [6–0] → Upper bits corresponding to address bits a19–a13 of the 20-bit
memory refresh address. These bits are not available on the a19–a0 bus. When using
PSRAM mode, M6–M0 must be programmed to 0000000b.
Bits [8–0]—Reserved → These bits read back as 0.
5.1.10 D1CON (0dah) and D0CON (0cah)
DMA CONtrol Registers. DMA Control Registers control operation of the two DMA channels.
The D0CON and D1CON registers are undefined at reset, except ST which is set to 0 (see
Table 26).
Table 26. DMA Control Registers
15
14
13
12
11
10 9 8
7
6
5
4
3
2
1
0
DM/IOn DDEC DINC SM/Ion SDEC SINC TC INT SYN1–SYN0 P TDRQ EXT CHG ST Bn/W
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 69 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [15]—DM/IOn → Destination Address Space Select selects memory or I/O space for
the destination address. When DM/IO is set to 1, the destination address is in memory
space. When 0, it is in I/O space.
Bit [14]—DDEC → Destination Decrement when set to 1, automatically decrements the
destination address after each transfer. The address is decremented by 1 or 2, depending
on the byte/word bit (Bn/W, Bit [0]). The address does not change if the increment and
decrement bits are set to the same value (00b or 11b).
Bit [13]—DINC → Destination Increment when set to 1, automatically increments the
destination address after each transfer. The address is incremented by 1 or 2, depending
on the byte/word bit (Bn/W, Bit [0]). The address does not change if the increment and
decrement bits are set to the same value (00b or 11b).
Bit [12]—SM/IOn → Source Address Space Select selects memory or I/O space for the
source address. When set to 1, the source address is in memory space. When 0, it is in
I/O space.
Bit [11]—SDEC → Source Decrement when set to 1, automatically decrements the
destination address after each transfer. The address is decremented by 1 or 2, depending
on the byte/word bit (Bn/W, Bit [0]). The address does not change if the increment and
decrement bits are set to the same value (00b or 11b).
Bit [10]—SINC → Source Increment when set to 1, automatically increments the
destination address after each transfer. The address is incremented by 1 or 2, depending
on the byte/word bit (Bn/W, Bit [0]). The address does not change if the increment and
decrement bits are set to the same value (00b or 11b).
Bit [9]—TC → Terminal Count. The DMA decrements the transfer count for each DMA
transfer. When set to 1, the source or destination synchronized DMA transfers terminate
when the count reaches 0. When 0, they do not terminate when the count reaches 0.
Unsynchronized DMA transfers always end when the count reaches 0, regardless of the
setting of this bit.
Bit [8]—INT → Interrupt. When this bit is set to 1, the DMA channel generates an
interrupt request on completion of the transfer count. However, for an interrupt to be
generated, the TC bit must also be set to 1.
Bits [7–6]—SYN1–SYN0 → Synchronization Type bits each select channel
synchronization types as shown below. The value of these bits is ignored if TDRQ
(Bit [4]) is set to 1. A processor reset causes these bits to be set to 11b.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 70 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Synchronization Bit Channel Selection
SYN1 SYN0
Sync Type
0
0
Unsynchronized
0
1
Source Synchronized
1
0
Destination Synchronized
1
1
Reserved
Bit [5]—P → Relative Priority. When set to 1, selects high priority for this channel
relative to the other channel during simultaneous transfers.
Bit [4]—TDRQ → Timer 2 Synchronization. When set to 1, enables DMA requests from
timer 2. When 0, disables them.
Bit [3]—EXT → External Interrupt Enable Bit. When set to 1, if the respective DMA
channel does not respond to changes on the drq pin, this pin functions as an int pin and
the interrupt controller processes requests on the pin. When 0, it functions as a drq pin.
Bit [2]—CHG → Change Start Bit. This bit must be set to 1 to allow modification of the
ST bit during a write. During a write, when CHG is set to 0, ST is not changed when
writing the control word. The result of reading this bit is always 0.
Bit [1]—ST → Start/Stop DMA Channel. When set to 1, the DMA channel is started.
The CHG bit must be set to 1 for this bit to be modified and only during the same register
write. A processor reset causes this bit to be set to 0.
Bit [0]—Bn/W → Byte/Word Select. When set to 1, word transfers are selected.
When 0, byte transfers are selected.
Note: Word transfers are not supported if the chip selects are programmed
for 8-bit transfers. The IA188ES does not support word transfers
5.1.11 D1TC (0d8h) and D0TC (0c8h)
DMA Transfer Count Registers. The DMA Transfer Count registers are maintained by each
DMA channel. They are decremented after each DMA cycle. The state of the TC bit in the
DMA control register has no influence on this activity. But, if unsynchronized transfers are
programmed or if the TC bit in the DMA control word is set, DMA activity ceases when the
transfer count register reaches 0. The D0TC and D1TC registers are undefined at reset (see
Table 27).
Table 27. DMA Transfer Count Registers
15
14
13
12
11
®
10 9 8 7
TC15–TC0
6
5
4
3
2
1
0
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 71 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bits [15–0]—TC [15–0] → DMA Transfer Count contains the transfer count for the
respective DMA channel. Its value is decremented after each transfer.
5.1.12 D1DSTH (0d6h) and D0DSTH (0c6h)
The DMA DeSTination Address High Register. The 20-bit destination address consists of these
4 bits combined with the 16 bits of the respective Destination Address Low Register. A DMA
transfer requires that two complete 16-bit registers (high and low registers) be used for both the
source and destination addresses of each DMA channel involved. These four registers must be
initialized. Each address may be incremented or decremented independently of each other after
each transfer. The addresses are incremented or decremented by two for word transfers and
incremented or decremented by one for byte transfers. They are undefined at reset (see
Table 28).
Table 28. DMA Destination Address High Register
15
14
13
12
11 10 9
Reserved
8
7
6
5
4
3 2 1 0
DDA19–DDA16
Bits [15–4]—Reserved.
Bits [3–0]—DDA [19–16] → DMA Destination Address High bits are driven onto
a19–a16 during the write phase of a DMA transfer.
5.1.13 DIDSTL (0d4h) and D0DSTL (0c4h)
DMA DeSTination Address Low Register. The 16 bits of these registers are combined with the
4 bits of the respective DMA Destination Address High Register to produce a 20-bit destination
address. They are undefined at reset (see Table 29).
Table 29. DMA Destination Address Low Register
15
14
13
12
11
10 9 8 7 6
DDA15–DDA0
5
4
3
2
1
0
Bits [15–0]—DDA [15–0] → DMA Destination Address Low bits are driven onto
a19–a16 during the write phase of a DMA transfer.
5.1.14 D1SRCH (0d2h) and D0SRCH (0c2h)
DMA SouRCe Address High Register. The 20-bit source address consists of these 4 bits
combined with the 16 bits of the respective Source Address Low Register. A DMA transfer
requires that two complete 16-bit registers in the PCB (high and low registers) be used for both
the source and destination addresses of each DMA channel involved. Each channel requires that
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 72 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
all four address registers be initialized. Each address may be independently incremented or
decremented after each word transfer by 2 or by 1 for byte transfers. They are undefined at reset
(see Table 30).
Table 30. DMA Source Address High Register
15
14
13
12
11 10 9
Reserved
8
7
6
5
4
3 2 1 0
DSA19–DSA16
Bits [15–4]—Reserved.
Bits [3–0]—DSA [19–16] → DMA Source Address High bits are driven onto a19–a16
during the read phase of a DMA transfer.
5.1.15 D1SRCL (0d0h) and D0SRCL (0c0h)
DMA SouRCe Address Low Register. The 16 bits of these registers are combined with the 4 bits
of the respective DMA Source Address High register to produce a 20-bit source address. They
are undefined at reset (see Table 31).
Table 31. DMA Source Address Low Register
15
14
13
12
11
10 9 8 7 6
DSA15–DSA0
5
4
3
2
1
0
Bits [15–0]—DSA [15–0] → DMA Source Address Low bits are placed onto a15–a0
during the read phase of a DMA transfer.
5.1.16 MPCS (0a8h)
MCS and PCS (MPCS) Auxiliary Register. Because this register controls more than one type of
chip select, it is unlike other chip select control registers. The MPCS register contains
information for mcs3_n–mcs0_n, pcs6_n–pcs5_n, and pcs3_n–pcs0_n.
The MPCS register also contains a bit that configures the pcs6_n–pcs5_n pins as either chip
selects or as alternate sources for the a2 and a1 address bits. Either a1/a2 or pcs6_n–pcs5_n are
selected to the exclusion of the other. When programmed for address bits, these outputs can be
used to provide latched address bits for a2 and a1.
The pcs6_n–pcs5_n pins are high and not active on processor reset. When the pcs6_n–pcs5_n
are configured as address pins, an access to the MPCS register causes them to activate. They do
not require corresponding access to the PACS register to be activated. The value of the MPCS
register is undefined at reset (see Table 32).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 73 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 32. MCS and PCS Auxiliary Register
15
1
14
13
12 11 10
M6–M0
9
8
7
EX
6
MS
5
1
4
1
3
1
2
R2
1
0
R1–R0
Bit [15]—Reserved → Set to 1.
Bits [14–8]—M [6–0] mcs_n Block Size → These seven bits determine the total memory
block size for the mcs3_n–mcs0_n chip selects. The size is divided equally among them.
The relationship between M [6–0] and the size is shown below.
Select Sizes of M6–M0 by Total Block Size
Total Block
Individual
Size
Select Size
M6–M0
8K
2K
0000001b
16K
4K
0000010b
32K
8K
0000100b
64K
16K
0001000b
128K
32K
0010000b
256K
64K
0100000b
512K
128K
1000000b
Bit [7]—EX Pin Selector → This bit determines whether the pcs6_n–pcs5_n pins are
configured as chip selects or as alternate outputs for a2 and a1. When set to 1,
they are configured as peripheral chip select pins. When 0, they become address bits a1
and a2, respectively.
Bit [6]—MS → Memory/ I/O Space Selector determines whether the pcs_n pins are
active during either memory or I/O bus cycles. When set to 1, the outputs are active for
memory bus cycles. When 0, they are active for I/O bus cycles.
Bits [5–3]—Reserved → Set to 1.
Bit [2]—R2 Ready Mode → This bit influences only the pcs6_n–pcs5_n chip selects.
When set to 1, external ready is ignored. When 0, it is required. Values determine the
number of wait states to be inserted.
Bits [1–0]—R [1–0] Wait-State Value → These bits influence only the pcs6_n–pcs5_n
chip selects. Their value determines the number of wait states inserted into an access,
depending on whether it is to the pcs_n memory or I/O area. Up to three wait states can
be inserted (R1–R0 = 00b to 11b).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 74 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
5.1.17 MMCS (0a6h)
Midrange Memory Chip Select (MMCS) Register. Four chip-select pins, mcs3_n–mcs0_n, are
provided for use within a user-locatable memory block. Excluding the areas associated with the
ucs_n and lcs_n chip selects (and if mapped to memory, the address range of the peripheral chip
selects, pcs6_n–pcs5_n and pcs3_n–pcs0_n), the memory block base address can be located
anywhere within the 1-Mbyte memory address space. If the pcs_n chip selects are mapped to
I/O space, the mcs_n address range can overlap the pcs_n address range.
Two registers program the Midrange Chip Selects. The MMCS register determines the base
address, the ready condition, and wait states of the memory block that are accessed through the
mcs_n pins. The pcs_n and mcs_n auxiliary (MPCS) register configures the block size. On
reset, the mcs3_n–mcs0_n pins are not active. Accessing with a write both the MMCS and
MPCS registers activate these chip selects.
Unlike the ucs_n and lcs_n chip selects, the mcs3_n–mcs0_n outputs assert with the multiplexed
ad address bus (ad15–ad0 or ao15–ao8 and ad7–ad0), rather than the earlier timing of the a19–a0
bus. If the a19–a0 bus is used for address selection, the timing is delayed for a half cycle later
than that for ucs_n and lcs_n. The value is undefined at reset (see Table 33).
Table 33. Midrange Memory Chip Select Register
15
14
13 12 11
BA19–BA13
10
9
8
1
7
1
6
1
5
1
4
1
3
1
2
R2
1
0
R1–R0
Bits [15–9]—BA [15–9] Base Address → The value of the BA19–BA13 determines the
base address of the memory block that is addressed by the mcs_n chip select pins. These
bits correspond to a19–a13 of the 20-bit memory address. The remaining bits a12–a0 of
the base address are always 0.
–
The base address may be any integer multiple of the size of the memory clock
selected in the MPCS register. For example, if the midrange block is 32 Kbytes, the
block could be located at 20000h or 28000h but not at 24000h.
–
If the lcs_n chip select is inactive, the base address of the midrange chip selects can
be set to 00000h, because the lcs_n chip select is defined to be 00000h but is unused.
Because the base address must be an integer multiple of the block size, a 512K
MMCS block size can only be used with the lcs_n chip select inactive and the base
address of the midrange chip selects set to 00000h.
Bits [8–3]—Reserved. Set to 1.
Bit [2]—R2 Ready mode → This bit determines the mcs_n chip selects ready mode.
When set to 1, an external ready is ignored. When 0, an external ready is necessary. Its
value determines the number of wait states inserted into an access.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 75 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bits [1–0]—R [1–0] → Wait-State Value. The value of these bits determines the number
of wait states inserted in an access. Up to three wait states can be inserted (R1–R0 = 00b
to 11b).
5.1.18 PACS (0a4h)
PeripherAl Chip Select Register. These Peripheral Chip Selects are asserted over 256-byte range
with the same timing as the ad address bus. There are six chip selects, pcs6_n–pcs5_n and
pcs3_n–pcs0_n that are used in either the user-locatable memory or I/O blocks. Excluding the
areas used by the ucs_n, lcs_n, and mcs_n chip selects, the memory block can be located
anywhere within the 1-Mbyte address space. These chip selects may also be configured to
access the 64-Kbyte I/O space.
Programming the Peripheral Chip Selects uses the Peripheral Chip Select (PACS) and the pcs_n
and mcs_n Auxiliary (MPCS) registers. The PACS register establishes the base address,
configures the ready mode, and determines the number of wait states for the pcs3_n–pcs0_n
outputs.
The MPCS register configures the pcs6_n–pcs5_n pins to be either chip selects or address pins
a1 and a2. When these pins are configured as chip selects, the MPCS register determines the
ready state and wait states for these output pins and whether they are active during memory or
I/O bus cycles. These pins are activated as chip selects by writing to the two registers (PACS
and MPCS). They are not active on reset. To configure and activate them as address pins, it is
necessary to write to both the PACS and MPCS registers. Pins pcs6_n–pcs5_n can be
configured for 0 to 3 wait states and pcs3_n–pcs0_n can be programmed for 0 to 15 wait states.
The value of the PACS register is undefined at reset (see Table 34).
Table 34. Peripheral Chip Select Register
15
14
13
12 11 10
BA19–BA11
9
8
7
6
1
5
1
4
1
3
R3
2
R2
1
0
R1–R0
Bits [15–7]—BA [19–11] → Base Address bits correspond to Bits [19–11] of the 20-bit
programmable base address of the peripheral chip select block and determine the base
address. Because I/O addresses are only 16 bits wide, if the pcs_n chip selects are
mapped to I/O space, these bits must be set to 0000b. The pcs address ranges are shown
below.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 76 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Address Ranges of pcs Chip Selects
Range
pcs_n Line
Low
High
pcs0_n
Base Address
Base Address + 255
pcs1_n
Base Address + 256
Base Address + 511
pcs2_n
Base Address + 512
Base Address + 767
pcs3_n
Base Address + 768
Base Address + 1023
Reserved
NA
NA
pcs5_n
Base Address + 1280 Base Address
pcs6_n
Base Address + 1536 Base Address
Bits [6–4]—Reserved. Set to 1.
Bit [3]—R [3] → Wait State Value. See pcs3_n–pcs0_n Wait-State Encoding shown
below.
pcs3_n–pcs0_n Wait-State Encoding
R3 R1 R0 Wait States
0
0
0
0
0
0
1
1
0
1
0
2
0
1
1
3
1
0
0
5
1
0
1
7
1
1
0
9
1
1
1
15
Bit [2]—R [2] → Ready Mode. When set to 1, external ready is ignored. When 0, it is
required. In each case the number of wait states is determined according to the
pcs3_n–pcs0_n Wait-State Encoding shown above.
Bits [1–0]—R [1–0] → Wait-State Value (see pcs3_n–pcs0_n Wait-State Encoding shown
above). The pcs6_n–pcs5_n and pcs3_n–pcs0_n pins are multiplexed with the PIO pins.
For them to function as chip selects, the PIO mode and direction settings for these pins
must be set to 0 for normal operation.
5.1.19 LMCS (0a2h)
The Low-Memory Chip Select (LMCS) Register configures the Low Memory Chip Select
provided to facilitate access to the interrupt vector table located at 00000h or the bottom of
memory. The lcs_n pin is not active at reset.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 77 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
The width of the data bus for the lcs_n space should be configured in the AUXCON register
before activating the lcs_n chip select pin, by any write access to the LMCS register. The value
of the LMCS register is undefined at reset except DA, which is set to 0 (see Table 35).
Table 35. Low-Memory Chip Select Register
15
0
14 13 12
UB2–UB0
11
1
10
1
9
1
8
1
7
DA
6
PSE
5
1
4
1
3
1
2
R2
1 0
R1-R0
Bit [15]—Reserved. Set to 0.
Bits [14–12]—UB [2–0] → Upper Boundary. These bits define the upper boundary of
memory accessed by the lcs_n chip select. The LMCS Block-Size Programming Values
shown below list the possible block-size configurations (a 512-Kbyte maximum).
LMCS Block-Size Programming Values
Memory
Ending
Block Size Address UB2–UB0
64K
0FFFFh
000b
128K
1FFFFh
001b
256K
3FFFFh
011b
512K
7FFFFh
111b
Bits [11–8]—Reserved. Set to 1.
Bit [7]—DA Disable Address → When set to 1, the address bus is disabled, providing
some measure of power saving. When 0, the address is driven onto the address bus
ad15–ad0 during the address phase of a bus cycle. This bit is set to 0 at reset.
–
If bhe_n/aden_n is held at 0 during the rising edge of res_n, the address bus is always
driven, regardless of the setting of DA.
Bit [6]—PSE PSRAM Mode Enable → When set to 1, PSRAM support for the lcs_n chip
select memory space is enabled. The EDRAM, MDRAM, and CDRAM RCU registers
must be configured for auto refresh before PSRAM support is enabled. Setting the
enable bit (EN) in the enable RCU register (EDRAM, offset e4h) configures the
mcs3_n/rfsh_n as rfsh_n.
Bits [5–3]—Reserved. Set to 1.
Bit [2]—R2 Ready Mode → When set to 1, the external ready is ignored. When 0, it is
required. The value of these bits determines the number of wait states inserted.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 78 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bits [R1–R0]—R [1–0] → Wait-State Value. The value of these bits determines the
number of wait states inserted into an access to the lcs_n memory area. This number
ranges from 0 to 3 (R1–R0 = 00b to 11b).
5.1.20 UMCS (0a0h)
The Upper Memory Chip Select Register configures the UMCS pin, used for the top of memory.
On reset, the first fetch takes place at memory location FFFF0h and thus this area of memory is
usually used for instruction memory. The ucs_n defaults to an active state at reset with a
memory range of 64 Kbytes (F0000h to FFFFFh), external ready required, and three wait states
automatically inserted. The upper end of the memory range always ends at FFFFFh. The lower
end of this upper memory range is programmable. The value of the UMCS register is F03Bh at
reset (see Table 36).
Table 36. Upper-Memory Chip Select Register
15
1
14 13 12
LB2–LB0
11
0
10
0
9
0
8
0
7
DA
6
0
5
1
4
1
3
1
2
R2
1
0
R1–R0
Bit [15]—Reserved. Set to 1.
Bits [14–12]—LB [2–0] → Lower Boundary. These bits determine the bottom of the
memory accessed by the ucs_n chip selects. The UMCS Block-Size Programming Values
shown below list the possible block-size configurations (a 512-Kbyte maximum).
UMCS Block-Size Programming Values
Memory
Starting
Block Size Address LB2–LB0 Comments
64K
F0000h
111b
Default
128K
E0000h
110b
–
256K
C0000h
100b
–
512K
80000h
000b
–
Bits [11–8]—Reserved. Set to 0.
Bit [7]—DA Disable Address → When set to 1, the address bus is disabled and the
address is not driven on the address bus when ucs_n is asserted, providing some measure
of power saving. When 0, the address is driven onto the address bus (ad15–ad0) during
the address phase of a bus cycle when ucs_n is asserted. This bit is set to 0 at reset.
–
If bhe_n/aden_n is held at 0 during the rising edge of res_n, the address bus is always
driven, regardless of the setting of DA.
Bit [6]—Reserved. Set to 0.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 79 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [5–3]—Reserved. Set to 1.
Bit [2]—R2 Ready Mode → When set to 1, the external ready is ignored. When 0, an
external ready is required. The value of these bits determines the number of wait states
inserted.
Bits [1–0]—R [1–0] Wait-State Value → The value of these bits determines the number
of wait states inserted into an access to the lcs_n memory area. This number ranges from
0 to 3 (R1–R0 = 00b to 11b).
5.1.21 SP0BAUD (088h)
Serial Port BAUD Rate Divisor Registers.
5.1.22 SP1BAUD (018h)
Two baud-rate divisor registers, one for each port, allow the two ports to operate at different
baud rates. The value in these registers determines the number of internal processor cycles in
one phase (one half period) of the 16x serial clock.
The contents of these registers must be adjusted to reflect the new processor clock frequency if
power-save mode is in effect.
The baud rate divisor may be calculated from:
BAUDDIV = (Processor Frequency/(16 x baud rate))
(Equation 2)
By setting the BAUDDIV to 0001h, the maximum baud rate of 1/16 of the internal processor
frequency clock is set. This provides a baud rate of 2500 Kbytes at 40 MHz. If the BAUDDIV
is set to zero, transmission or reception of data does not occur. The baud rate tolerance is +3.0%
and −2.5% with respect to the actual serial port baud rate, not the target baud rate (see Table 37).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 80 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 37. Baud Rates
Baud Rate
300
600
1050
1200
1800
2400
4800
7200
9600
19200
28800
38400
56000
57600
76800
115200
128000
153600
Special
187500
Divisor Based on CPU Clock Rate
20 MHz 25 MHz 33 MHz 40 MHz
4166
5208
6875
8333
2083
2604
3437
4166
1190
1488
1964
2380
1041
1302
1718
2083
694
868
1145
1388
520
651
859
1041
260
325
429
520
173
217
286
347
130
162
214
260
65
81
107
130
43
54
71
86
33
40
53
65
22
28
36
45
22
27
35
43
16
20
26
32
10
13
18
22
9
12
16
19
8
10
13
16
15 MHz 21 MHz 24 MHz 30 MHz
5
7
8
10
The value of the SP0BAUD and SP1BAUD registers at reset is 0000h (see Table 38).
Table 38. Serial Port Baud Rate Divisor Registers
15
14
13
12
11
10
9 8 7
BAUDDIV
6
5
4
3
2
1
0
Bits [15–0]—BAUDDIV Baud Rate Divisor → Defines the divisor for the internal
processor clock.
5.1.23 SP0RD (086h) and SP1RD (016h)
Serial Port Receive Registers. Data received over the serial ports are stored in these registers
until read. The data are received initially by the receive shift register (no software access)
permitting data to be received while the previous data are being read.
The status of these registers is indicated by the RDR bit (Receive Data Ready) in the serial port
status registers. Setting the RDR bit to 1 indicates that there is valid data in the receive register.
The RDR bit is cleared automatically when the receive register is read.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 81 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
If handshaking is employed, the control signals cts_n/enrx_n are deasserted while the receive
register has valid unread data. The cts_n/enrx_n signal is reasserted after the data in the receive
register is read. The value of the SP0RD and SP1RD registers is undefined at reset (see
Table 39).
Table 39. Serial Port Receive Registers
15
14
13
12 11
Reserved
10
9
8
7
6
5
4 3 2
RDATA
1
0
Bits [15–8]—Reserved.
Bits [7–0]—RDATA → Holds valid data while the RDR bit of the respective status
register is set.
5.1.24 SP0TD (084h) and SP1TD (014h)
Serial Port Transmit Registers. Data is written to these registers by software with the values to
be transmitted by the serial port. Double buffering of these transmitters allows for the
transmission of data from the transmit shift registers (no software access), while the next data are
written into the transmit registers.
The TEMT and THRE bits in the respective Serial Port Status registers indicate the status of
these two pairs of registers.
Invoking handshaking requires that rts_n/rtr_n inputs be asserted before the transmitters can send
any data which remain held in the transmit and shift registers without affecting the transmit pin.
The value of the SPTD registers is undefined at reset (see Table 40).
Table 40. Serial Port Transmit Registers
15
14
13
12 11
Reserved
10
9
8
7
6
5
4 3 2
TDATA
1
0
Bits [15–8]—Reserved.
Bits [7–0]—TDATA → Holds the data to be transmitted.
5.1.25 SP0STS (082h) and SP1STS (012h)
Serial Port Status Register. These registers store information concerning the current status of the
respective ports. The value of the SP0STS and SP1STS registers is undefined at reset (see
Table 41).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 82 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 41. Serial Port Status Register
15
14 13 12
Reserved
11
10
BRK1
9
BRK0
8
RB8
7
RDR
6
THRE
5
FER
4
OER
3
PER
2
TEMT
1
HS0
0
Res
Bits [15–11]—Reserved.
Bit [10]—BRK1 Long Break Detected → A long break is a low signal level on the rxd
pin for a period greater that 2M + 3 bit times, where:
M = start bit + number of data bits + parity bits + stop bit
(Equation 3)
–
Should data reception be in progress when the break starts, the reception of the
current word will be completed and the timing for the break will begin. Because the
stop bit will not be detected due to the break, this will generate a framing error.
–
Detection of the break with the 2M + 3 bit time period can only be guaranteed if the
break commences outside of a frame.
Note: This bit should be reset by software.
Bit [9]—BRK0 Short Break Detected → A short break is a low on the rxd pin for a
period greater than M bit times (see Equation 3 above).
–
Should data reception be in progress when the break starts, the reception of the
current word will be completed and the timing for the break will begin. Because the
stop bit will not be detected due to the break, this will generate a framing error.
–
Detection of the break with the M bit time period can only be guaranteed if the break
commences outside of a frame.
Note: This bit should be reset by software.
Bit [8]—RB8 Received Bit [8] → This is the ninth data bit received in modes 2 and 3
(see Section 5.1.26, SP0CT (080h) and SP1CT (010h)).
Note: This bit should be reset by software.
Bit [7]—RDR Receive Data Ready → When this bit is 1, it indicates that the respective
SPRD register contains valid data. This is a read-only bit and can be reset only by
reading the corresponding receive register.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 83 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [6]—THRE Transmit Holding Register Empty → When this bit is 1, it indicates that
the corresponding transmit holding register is ready to accept data. This is a read-only
bit.
Bit [5]—FER Framing Error Detected → When the receiver samples the rxd line as low
when a stop bit is expected (line high), a framing error is generated setting this bit.
Note: This bit should be reset by software.
Bit [4]—OER Overrun Error Detected → When new data overwrites valid data in the
receive register (because it has not been read), an overrun error is detected setting this bit.
Note: This bit should be reset by software.
Bit [3]—PER Parity Error Detected → When a parity error is detected in either mode 1
or 3, this bit is set.
Note: This bit should be reset by software.
Bit [2]—TEMT Transmitter Empty → When both the transmit shift register and the
transmit register are empty, this bit is set indicating to software that it is safe to disable
the transmitter. This bit is read-only.
Bit [1]—HS0 Handshake Signal 0 → This bit is the inverted value of cts_n and is read
only.
Bit [0]—RES Reserved.
5.1.26 SP0CT (080h) and SP1CT (010h)
Serial Port ConTrol Registers. These registers control both transmit and receive parts of the
respective serial ports. The value of the SP0CT and SP1CT registers is 0000h at reset (see
Table 42).
Table 42. Serial Port Control Registers
15
14 13
DMA
12
RSIE
11
BRK
10
TB8
9
FC
8
TXIE
7
RXIE
6
TMODE
5
RMODE
4
EVN
3
PE
2 1 0
MODE
Bits [15–13]—DMA DMA Control Field → These bits set up the respective ports for use
with DMA transfers as shown below.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 84 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
DMA Control Bits
DMA Bits
Receive
000b
No DMA
001b
DMA0
010b
DMA1
011b
Reserved
100b
DMA0
101b
DMA1
110b
No DMA
111b
No DMA
Data Sheet
November 15, 2011
Transmit
No DMA
DMA1
DMA0
Reserved
No DMA
No DMA
DMA0
DMA1
–
DMA transfers to both serial ports are destination-synchronized operations. When the
transmit holding register is empty, a new transfer is requested, corresponding with the
assertion of the THRE bit in the status register in non-DMA mode. However, when
configured for DMA transfers, the respective transmit interrupt is disabled without
regard for the TXIE bit.
–
DMA transfers from both serial ports are source-synchronized operations. When the
receive holding register contains valid data, a new transfer is requested,
corresponding with the assertion of the RDR bit in the status register in non-DMA
mode. However, when configured for DMA receives, the respective receive interrupt
is disabled without regard for the RXIE bit. This is despite the fact that the RSIE bit
may still permit receive status interrupts, depending on its setting.
–
DMA transfers do not preclude the use of hardware handshaking.
–
If either or both serial ports are configured for DMA transfers, the DMA request is
internally generated and the corresponding external DMA signals, drq0 and/or drq1
do not play a role.
Bit [12]—RSIE Receive Status Interrupt Enable → When an exception occurs during
data reception, an interrupt request is generated if enabled by this bit (RSIE = 1).
Interrupt requests are made for the error conditions listed (BRK0, BRK1, OER, PER, and
FER) in the serial port status register.
Bit [11]—BRK Send Break → When this bit is set to 1, the txd pin is driven low
overriding any data that may be in the course of being shifted out of the transmit shift
register.
Note: See the definitions of long and short break in the Serial Port Status
register definition.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 85 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [10]—TB8 Transmit Bit 8 → This is the ninth data bit transmitted when in modes 2
and 3. This bit is cleared at each transmitted word and is not buffered. To transmit data
with this bit set high, the following procedure is recommended.
1. The TEMT bit in the serial port status register must go high.
2. Set the TB8 bit by writing it to the serial port control register.
3. Write the transmit character to the serial port transmit register.
Bit [9]—FC Flow Control Enable → This bit controls the hardware handshake (flow
control) by enabling it when set to 1, and vice versa. The type of flow control depends on
the value of the ENRX0/ENRX1 and RTS0/RTS1 bits in the AUXCON register.
–
Serial Port 0 is a special case in that, if this bit is 1, the associated pins are used for
flow control overriding the Peripheral Chip Select signals.
–
This bit is 0 at reset.
Bit [8]—TXIE Transmitter Ready Interrupt Enable → This bit enables the generation of
an interrupt request whenever the transmit holding register is empty (THRE Bit [1]). The
respective port does not generate interrupts when this bit is 0. Interrupts continue to be
generated as long as THRE and the TXIE are 1.
Bit [7]—RXIE Receive Data Ready Interrupt Enable → This bit enables the generation of
an interrupt request whenever the receive register contains valid data (RDR Bit [1]). The
respective port does not generate interrupts when this bit is 0. Interrupts continue to be
generated as long as RDR and the RXIE are 1.
Bit [6]—TMODE Transmit Mode → The transmit section of the serial port is enabled
when this bit is 1. Conversely, the transmit section of the serial port is disabled when this
bit is 0.
Bit [5]—RMODE Receive Mode → The receive section of the serial port is enabled
when this bit is 1. Conversely, the receive section of the serial port is disabled when this
bit is 0.
Bit [4]—EVN Even Parity → When this bit is 1, even parity protocol is established.
Conversely, odd parity is established when this bit is 0. This bit is valid only when parity
is enabled (PE).
Bit [3]—PE Parity Enable → Parity is enabled when this bit is 1 and disabled when this
bit is 0.
Bit [2–0]—MODE Mode of Operation → These three bits establish the mode of
operation of the respective serial port. The valid modes and their functions are shown
below.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 86 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Serial Port MODE Settings
MODE
0a
1
2
3
4
5a
6a
7a
Description
Data Mode 0
Data Mode 1
Data Mode 2
Data Mode 3
Data Mode 4
Data Mode 5
Data Mode 6
Data Mode 7
Data
Bits
7
7 or 8
9
8 or 9
7
7 or 8
9
8 or 9
Parity
Bits
–
1 or 0
–
1 or 0
–
1 or 0
0
1 or 0
Stop
Bits
2
1
1
1
1
2
2
2
aThese
were originally reserved modes that have
been implemented to provide 2 stop bits.
–
Mode 2 requires that the ninth data is set to a 1 state. Otherwise, the character will be
ignored by the receiver. The transmit section, however, operates as if it were in
Mode 3.
–
This is designed to facilitate multidrop communication over a common serial data
link. For this purpose, the port in question is initially programmed to mode 2 and for
each data received with the ninth bit (Bit [8]) set as 1. It is compared by software
with a unique identifier for this port. If the identifier comparison does not find a
match, the port is left in mode 2. If the comparison finds an identifier match, the port
should be reprogrammed to mode 3 so that the ninth bit is allowed to be 0.
–
Handshaking should only be employed in such a multidrop system by ports that are
exchanging data (mode 3) to prevent multiple ports from attempting to drive the
handshake signals. Mode 2 does not support handshaking for this reason and should
not be enabled. If it is possible that more than 2 ports be configured in mode 3 at the
same time, handshaking should not be implemented.
–
Mode 3 allows for 8 data bits if parity is enabled or 9 data bits if parity is not enabled.
If parity is not used, the ninth data bit for the transmit section is set by writing a 1 to
the TB8 bit in the serial port control register. The ninth bit is read at the receive port
from the RB8 bit in the serial port status register.
–
Mode 4 allows for a start bit, 7 data bits, and a stop bit without parity, which is not
available.
5.1.27 PDATA1 (07ah) and PDATA0 (074h)
PIO DATA Registers. When a PIO pin is configured as an output, the value in the
corresponding PIO data register bit is driven onto the pin. However, if the PIO pin is configured
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 87 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
as an input, the value on the pin is put into the corresponding bit of the PIO data register.
Table 43 lists the default states for the PIO pins.
Table 43. PIO Pin Assignments
PIO Number
0
1
2
3
4
5
6
7c
8c
9c
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26c,d
27
28
29c,d
30
31
Associated Pin Name
tmrin1
tmrout1
pcs6/A2
pcs5/A1
dt/r_n
den_n/ds_n
srdy
a17
a18
a19
tmrout0
tmrin0
drq0/int5
drq1/int6
mcs0_n
mcs1_n
pcs0_n
pcs1_n
pcs2_n/cts1_n/enrx1_n
pcs3_n/rts1_n/rtr1_n
rts0_n/rtr0_n
cts0_n/enrx0_n
txd0
rxd0
mcs2_n
mcs3_n/rfsh_n
uzi
txd1
rxd1
s6/lock_n/clkdiv2_n
int4
int2/inta0_n/pwd
Power-On Reset Status
Input with pull-up
Input with pull-down
Input with pull-up
Input with pull-up
Normal operationa
Normal operationa
Normal operationb
Normal operationa
Normal operationa
Normal operationa
Normal operationa
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
Input with pull-up
aWhen used as a PIO pin, it is an input with an available pull-up option.
bWhen used as a PIO pin, it is an input with an available pull-down option.
cEmulators use these pins. (The s2_n–s0_n, res_n, nmi, clkouta, bhe_n, ale,
ad15–ad0, and a16–a0
pins are used by emulators also.)
dIf bhe_n/aden_n is held low during POR, these pins revert to normal operation.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 88 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
The 32 PIO pins initialize to either 00b or 01b as shown in Tables 44 and 45. The value of the
PDATA registers is undefined at reset.
Table 44. PDATA 0
15
14
13
12
11
10 9 8 7 6
PDATA (15–0)
5
4
3
2
1
0
10 9 8 7 6
PDATA (31–16)
5
4
3
2
1
0
Table 45. PDATA 1
15
14
13
12
11
Bits [15–0]—PDATA [15–0] PIO Data 0 Bits → This register contains the values of the
bits that are either driven on, or received from, the corresponding PIO pins. Depending
on its configuration each pin is either an output or an input. The values of these bits
correspond to those in the PIO direction registers and PIO Mode registers.
Bits [15–0]—PDATA [31–16] PIO Data 1 Bits → This register contains the values of the
bits that are either driven on, or received from, the corresponding PIO pins. Depending
on its configuration each pin is either an output or an input. The values of these bits
correspond to those in the PIO direction registers and PIO Mode registers
The PIO pins may be operated as open-drain outputs by:
–
Maintaining the data constant in the appropriate bit of the PIO data register.
–
Writing the value of the data bit into the respective bit position of the PIO Direction
register, so that the output is either 0 or disabled depending on the value of the data
bit.
5.1.28 PDIR1 (078h) and PDIR0 (072h)
PIO DIRection Registers. Each PIO pin is configured as an input or an output by the
corresponding bit in the PIO direction register (see Table 46).
Table 46. PIO Mode and PIO Direction Settings
PIO Mode
0
0
1
1
PIO Direction
0
1
0
1
®
Pin function
Normal operation
PIO input with pullup/pulldown
PIO output
PIO input without pullup/pulldown
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 89 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
The value of the PDIR0 register is FC0Fh at reset (see Table 48).
Table 47. PDIR0
15
14
13
12
11
10 9 8 7
PDIR (15–0)
6
5
4
3
2
1
0
The value of the PDIR1 register is FFFFh at reset (see Table 48).
Table 48. PDIR1
15
14
13
12
11
10 9 8 7 6
PDIR (31–16)
5
4
3
2
1
0
Bits [15–0]—PDIR [15–0] PIO Direction 0 Bits → For each bit, if the value is 1, the pin
is configured as an input. If 0, as an output. The values of these bits correspond to those
in the PIO data registers and PIO mode registers.
Bits [15–0]—PDIR [31–16] PIO Direction 1 Bits → For each bit, if the value is 1, the pin
is configured as an input. If 0, as an output. The values of these bits correspond to those
in the PIO data registers and PIO mode registers.
5.1.29 PMODE1 (076h) and PMODE0 (070h)
PIO MODE Registers. Each PIO pin is configured as an input or an output by the corresponding
bit in the PIO direction register. The bit number of PMODE corresponds to the PIO number (see
Table 46, PIO Mode and PIO Direction Settings). The value of the PMODE0 register is 0000h
at reset (see Table 49).
Table 49. PMODE0
15
14
13
12
11
10 9 8 7 6
PMODE (15–0)
5
4
3
2
1
0
The value of the PMODE1 register is 0000h at reset (see Table 50).
Table 50. PMODE1
15
14
13
12
11
10 9 8 7 6
PMODE (31–16)
5
4
3
2
1
0
Bits [15–0]—PMODE [15–0] PIO Mode 0 Bits → For each bit, if the value is 1, the pin
is configured as an input. If 0, an output. The values of these bits correspond to those in
the PIO data registers and PIO Mode registers.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 90 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bits [15–0]—PMODE [31–16] PIO Mode 1 Bits → For each bit, if the value is 1, the pin
is configured as an input. If 0, an output. The values of these bits correspond to those in
the PIO data registers and PIO Mode registers.
5.1.30 T1CON (05eh) and T0CON (056h)
Timer0 and Timer1 Mode and CONtrol Registers. These registers control the operation of
Timer0 and Timer1, respectively. The value of the T0CON and T1CON registers is 0000h at
reset (see Table 51).
Table 51. Timer0 and Timer1 Mode and Control Registers
15
EN
14
INHn
13
INT
12
RIU
11
0
10
0
9
0
8
0
7
0
6
0
5
MC
4
RTG
3
P
2
EXT
1
ALT
0
CONT
Bit [15]—EN Enable Bit → The timer is enabled when the EN bit is 1. The timer count
is inhibited when the EN bit is 0. Setting this bit to 1 by writing to the T2CON register
requires that the INHn bit be set to 1 during the same write. This bit is write-only and
can only be written if the INHn bit (Bit [14]) is set to 1 in the same operation.
Bit [14]—INHn Inhibit Bit → Gates the setting of the enable (EN) bit. This bit must be
set to 1 in the same write operation that sets the enable (EN) bit. This bit always reads
as 0.
Bit [13]—INT Interrupt Bit → An interrupt request is generated when the Count register
reaches its maximum, MC = 1, by setting the INT bit to 1. In dual maxcount mode, an
interrupt request is generated when the count register reaches the value in maxcount A or
maxcount B. No interrupt requests are generated if this bit is set to 0. If an interrupt
request is generated and then the enable bit is cleared before said interrupt is serviced, the
interrupt request will remain.
Bit [12]—RIU Register in Use Bit → This bit is set to 1 when the maxcount register B is
used to compare to the timer count value. It is set to 0 when the maxcount compare A
register is used.
Bits [11–6]—Reserved. Set to 0.
Bit [5]—MC Maximum Count → When the timer reaches its maximum count, this bit is
set to 1 regardless of the interrupt enable bit. This bit is also set every time maxcount
compare register A or B is reached when in dual maxcount mode. This bit may be used
by software polling to monitor timer status rather than through interrupts, if desired.
Bit [4]—RTG Retrigger Bit.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 91 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [3]—P Prescaler Bit → P is ignored if external clocking is enabled (EXT = 1). Timer
2 prescales the timer when P is set to 1. Otherwise, the timer is incremented on every
fourth CLKOUT cycle.
Bit [2]—EXT External Clock Bit → This bit determines whether an external or internal
clock is used. If EXT = 1, an external clock is used. If EXT = 0, an internal is used.
Bit [1]—ALT Alternate Compare Bit → If set to 1, the timer will count to maxcount
compare register A, reset the count register to 0, and then count to maxcount compare
register B, reset the count register to 0, and begin again at maxcount compare register A.
If set to 0, the timer will count to maxcount compare register A, reset the count register
to 0, and begin again at maxcount compare register A. Maxcount compare register B is
not used in this case.
Bit [0]—CONT Continuous Mode Bit → The timer will run continuously when this bit is
set to 1. The timer will stop after each count run and EN will be cleared if the CONT bit
is set to 0. If CONT = 1 and ALT = 1, the respective timer counts to the maxcount
compare A value and resets, then it commences counting to maxcount compare B value,
resets and ceases counting.
5.1.31 T2CON (066h)
Timer2 Mode and CONtrol Registers. This register controls the operation of the Timer2. The
value of the T2CON register is 0000h at reset (see Table 52).
Table 52. Timer2 Mode and Control Registers
15
EN
14
INHn
13
INT
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
MC
4
0
3
0
2
0
1
0
0
CONT
Bit [15]—EN Enable Bit → The timer is enabled when the EN bit is 1. The timer count
is inhibited when the EN bit is 0. Setting this bit to 1 by writing to the T2CON register
requires that the INH bit be set to 1 during the same write. This bit is write-only, but with
the INHn bit set to 1 in the same write operation.
Bit [14]—INH Inhibit Bit → Gates the setting of the enable (EN) bit. This bit must be
set to 1 in the same write operation that sets the enable (EN) bit. This bit always reads
as 0.
Bit [13]—INT Interrupt Bit → An interrupt request is generated when the Count register
reaches its maximum, MC = 1, by setting the INT bit to 1.
Bits [12–6]—Reserved. Set to 0.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 92 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [5]—MC Maximum Count → When the timer reaches its maximum count, this bit is
set to 1 regardless of the interrupt enable bit. This bit may be used by software polling to
monitor timer status rather than through interrupts if desired.
Bits [4–1]—Reserved. Set to 0.
Bit [0]—CONT Continuous Mode Bit → The timer will run continuously when this bit is
set to 1. The timer will stop after each count run and EN will be cleared if this bit is set
to 0.
5.1.32 T2COMPA (062h), T1COMPB (05ch), T1COMPA (05ah), T0COMPB (054h), and
T0COMPA (052h)
Timer Maxcount COMpare Registers. These registers contain the maximum count value that is
compared to the respective count register. Timer0 and Timer1 have two of these compare
registers each.
If Timer0 and/or Timer1 is/are configured to count and compare firstly to register A and then
register B, the TMROUT0 or TMROUT1 signals may be used to generate various duty-cycle
wave forms.
Timer2 has only one compare register, T2COMPA.
If one of these timer maxcount compare registers is set to 0000h, the respective timer will count
from 0000h to FFFFh before generating an interrupt request. For example, a timer configured in
this manner with a 40-MHz clock will interrupt every 6.5536 µS.
The value of these registers is 0000h at reset (see Table 53).
Table 53. Timer Maxcount Compare Registers
15
14
13
12
11
10 9 8 7
TC15–TC0
6
5
4
3
2
1
0
Bits [15–0]—TC [15–0] Timer Compare Value → The timer will count to the value in the
respective register before resetting the count value to 0.
5.1.33 T2CNT (060h), T1CNT (058h), and T0CNT (050h)
Timer CouNT Registers. These registers are incremented by one every four internal clock cycles
if the relevant timer is enabled.
The Increment of Timer0 and Timer1 may also be controlled by external signals tmrin0 and
tmrin1 respectively, or prescaled by Timer2.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 93 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Comparisons are made between the count registers and maxcount registers and action taken
dependent on achieving the maximum count.
The value of these registers is 0000h at reset (see Table 54).
Table 54. Timer Count Registers
15
14
13
12
11
10 9 8 7
TC15–TC0
6
5
4
3
2
1
0
Bits [15–0]—TC [15–0] Timer Count Value → This register has the value of the current
count of the related timer that is incremented every fourth processor clock in internal
clocked mode. Alternatively, the register is incremented each time the Timer2 maxcount
is reached if using Timer2 as a prescaler. Timer0 and Timer1 may be externally clocked
by tmrin0 and tmrin1 signals.
5.1.34 SP0CON (044h) and SP1CON (042h) (Master Mode)
Serial Port Interrupt CONtrol Registers. These registers control the operation of the serial ports’
interrupt source. The value of these registers is 001Fh at reset (see Table 55).
Table 55. Serial Port Interrupt Control Registers
15
14
13
12
11 10 9
Reserved
8
7
6
5
4
Res
3
MSK
2
PR2
1
PR1
0
PR0
Bits [15–5]—Reserved. Set to 0.
Bit [4]—Reserved. Set to 1.
Bit [3]—MSK Mask → When 0, this bit enables the serial port to cause an interrupt.
When 1, it prevents the serial port from generating an interrupt.
Bits [2–0]—PR [2–0] Priority. These bits define the priority of the serial port interrupt in
relation to other interrupt signals. The interrupt priority is the lowest at 7 upon reset. The
values of PR2–PR0 are shown below.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 94 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Values of PR2–PR0 by Priority
Priority
PR2–PR0
(High) 0 000b
1
001b
2
010b
3
011b
4
100b
5
101b
6
110b
(Low) 7 111b
5.1.35 I4CON (040h) (Master Mode)
INT4 CONtrol Register. The int4 signal is intended only for use in fully nested mode and is not
available in cascade mode. The value of the I4CON register is 000Fh at reset (see Table 56).
Table 56. INT4 Control Register
15
14
13
12
11 10 9
Reserved
8
7
6
5
4
LTM
3
MSK
2
PR2
1
PR1
0
PR0
Bits [15–5]—Reserved. Set to 0.
Bit [4]—LTM Level-Triggered Mode → The int4 interrupt may be edge- or leveltriggered, depending on the value of the bit. If LTM is 1, int4 is active high levelsensitive interrupt. If 0, it is a rising-edge triggered interrupt. The interrupt int4 must
remain active (high) until serviced.
Bit [3]—MSK Mask → The int4 signal can cause an interrupt if the MSK bit is 0. The
int4 signal cannot cause an interrupt if the MSK bit is 1.
Bit [2–0]—PR [2–0] Priority → These bits define the priority of the serial port interrupt
in relation to other interrupt signals. The interrupt priority is the lowest at 7 upon reset.
The values of PR2–PR0 are shown above.
5.1.36 I3CON (03eh) and I2CON (03ch) (Master Mode)
INT2/INT3 CONtrol Register. INT2 and INT3 are designated as interrupt type 0eh and 0fh,
respectively.
The int2 and int3 pins may be configured as the interrupt acknowledge pins inta0 and inta1,
respectively, the signals in cascade mode. The value of these registers is 000Fh at reset (see
Table 57).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 95 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 57. INT2/INT3 Control Register
15
14
13
12
11 10 9
Reserved
8
7
6
5
4
LTM
3
MSK
2
PR2
1
PR1
0
PR0
Bits [15–5]—Reserved. Set to 0.
Bit [4]—LTM Level-Triggered Mode → The int2 or int3 interrupt may be edge- or leveltriggered depending on the value of this bit. If LTM is 1, int2 or int3 is an active high
level-sensitive interrupt. If 0, it is a rising-edge triggered interrupt. The interrupt int2 or
int3 must remain active (high) until acknowledged.
Bit [3]—MSK Mask → The int2 or int3 signal can cause an interrupt if the MSK bit is 0.
The int2 or int3 signal cannot cause an interrupt if the MSK bit is 1. The Interrupt Mask
Register has a duplicate of this bit.
Bit [2–0]—PR [2–0] Priority → These bits define the priority of the serial port interrupt
int2 or int3 in relation to other interrupt signals. The interrupt priority is the lowest at 7
upon reset. The values of PR2–PR0 are shown above.
5.1.37 I1CON (03ah) and I0CON (038h) (Master Mode)
INT0/INT1 CONtrol Register. IINT0 and INT1 are designated as interrupt type 0ch and 0dh,
respectively.
The int2 and int3 pins may be configured as the interrupt acknowledge pins inta0 and inta1,
respectively, the signals in cascade mode. The value of these registers is 000Fh at reset (see
Table 58).
Table 58. INT0/INT1 Control Register
15
14
13
12 11 10
Reserved
9
8
7
6
SFNM
5
C
4
LTM
3
MSK
2
PR2
1
PR1
0
PR0
Bits [15–7]—Reserved. Set to 0.
Bit [6]—SPNM Special Fully Nested Mode → This bit enables fully-nested mode for
int0 or int1 when set to 1.
Bit [5]—C Cascade Mode → This bit enables cascade mode for int0 or int1 when set
to 1.
Bit [4]—LTM Level-Triggered Mode → The int0 or int1 interrupt may be edge- or leveltriggered depending on the value of the bit. If LTM is 1, int0 or int1 is an active high
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 96 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
level-sensitive interrupt. If 0, it is a rising-edge triggered interrupt. The interrupt int0 or
int1 must remain active (high) until acknowledged.
Bit [3]—MSK Mask → The int0 or int1 signal can cause an interrupt if the MSK bit is 0.
The int0 or int1 signal cannot cause an interrupt if the MSK bit is 1. The Interrupt Mask
Register has a duplicate of this bit.
Bit [2–0]—PR [2–0] Priority → These bits define the priority of the serial port interrupt
int0 or int1 in relation to other interrupt signals. The interrupt priority is the lowest at 7
at reset. The values of PR2–PR0 are shown above.
5.1.38 TCUCON (032h) (Master Mode)
Timer Control Unit Interrupt CONtrol Register. The three timers, Timer2, Timer1, and Timer0,
have their interrupts assigned to types 08h, 12h, and 13h and are configured by this register. The
value of these registers is 000Fh at reset (see Table 59).
Table 59. Timer Control Unit Interrupt Control Register
15
14
13
12
11 10 9
Reserved
8
7
6
5
4
3
MSK
2
PR2
1
PR1
0
PR0
Bits [15–4]—Reserved. Set to 0.
Bit [3]—MSK Mask → Any of the interrupt sources may cause an interrupt if the MSK
bit is 0. The interrupt sources cannot cause an interrupt if the MSK bit is 1. The Interrupt
Mask Register has a duplicate of this bit.
Bit [2–0]—PR [2–0] Priority → These bits define the priority of the serial port interrupts
in relation to other interrupt signals. The interrupt priority is the lowest at 7 upon reset.
The values of PR2–PR0 are shown above.
5.1.39 T2INTCON (03ah), T1INTCON (038h), and T0INTCON (032h) (Slave Mode)
Timer INTerrupt CONtrol Register. The three timers, Timer2, Timer1, and Timer0, each have
an interrupt control register, whereas in master mode all three are masked and prioritized in one
register (TCUCON). The value of these registers is 000Fh at reset (see Table 60).
Table 60. Timer Interrupt Control Register
15
14
13
12
11 10 9
Reserved
®
8
7
6
5
4
3
MSK
2 1 0
PR2–PR0
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 97 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bits [15–4]—Reserved. Set to 0.
Bit [3]—MSK Mask → Any of the interrupt sources may cause an interrupt if the MSK
bit is 0. The interrupt sources cannot cause an interrupt if the MSK bit is 1. The Interrupt
Mask Register has a duplicate of this bit.
Bit [2–0]—PR [2–0] Priority → These bits define the priority of the serial port interrupts
in relation to other interrupt signals. The interrupt priority is the lowest at 7 upon reset.
The values of PR2–PR0 are shown above.
5.1.40 DMA1CON/INT6CON (036h) and DMA0CON/INT5CON (034h) (Master Mode)
DMA and INTerrupt CONtrol Register. The DMA0 and DMA1 interrupts have interrupt type
0ah and 0bh, respectively. These pins are configured as external interrupts or DMA requests in
the respective DMA Control register. The value of these registers is 000Fh at reset (see
Table 61).
Table 61. DMA and Interrupt Control Register (Master Mode)
15
14
13
12
11 10 9
Reserved
8
7
6
5
4
3
MSK
2 1 0
PR2–PR0
Bits [15–4]—Reserved. Set to 0.
Bit [3]—MSK Mask → Any of the interrupt sources may cause an interrupt if the MSK
bit is 0. The interrupt sources cannot cause an interrupt if the MSK bit is 1. The Interrupt
Mask Register has a duplicate of this bit.
Bits [2–0]—PR [2–0] Priority → These bits define the priority of the serial port interrupts
in relation to other interrupt signals. The interrupt priority is the lowest at 7 upon reset.
The values of PR2–PR0 are shown above.
5.1.41 DMA1CON/INT6 (036h) and DMA0CON/INT5 (034h) (Slave Mode)
DMA and INTerrupt CONtrol Register. The two DMA control registers maintain their original
functions and addressing that they possessed in Master Mode. These pins are configured as
external interrupts or DMA requests in the respective DMA Control register. The value of these
registers is 000Fh at reset (see Table 62).
Table 62. DMA and Interrupt Control Register (Slave Mode)
15
14
13
12
11 10 9
Reserved
®
8
7
6
5
4
3
MSK
2 1 0
PR2–PR0
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 98 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bits [15–4]—Reserved. Set to 0.
Bit [3]—MSK Mask → Any of the interrupt sources may cause an interrupt if the MSK
bit is 0. The interrupt sources cannot cause an interrupt if the MSK bit is 1. The Interrupt
Mask Register has a duplicate of this bit.
Bits [2–0]—PR [2–0] Priority → These bits define the priority of the serial port interrupts
in relation to other interrupt signals. The interrupt priority is the lowest at 7 upon reset.
The values of PR2–PR0 are shown above.
5.1.42 INTSTS (030h) (Master Mode)
INTerrupt STatuS Register. The Interrupt status register contains the interrupt request status of
each of the three timers, Timer2, Timer1, and Timer0 (see Table 63).
Table 63. Interrupt Status Register (Master Mode)
15
DHLT
14
13
12
11
10 9 8
Reserved
7
6
5
4
3
2
1
0
TMR2–TMR0
Bit [15]—DHLT DMA Halt → DMA activity is halted when this bit is 1. It is set to 1
automatically when any non-maskable interrupt occurs and is cleared to 0 when an IRET
instruction is executed. Interrupt handlers and other time-critical software may modify
this bit directly to disable DMA transfers. However, the DHLT bit should not be
modified by software if the timer interrupts are enabled as the function of this register as
an interrupt request register for the timers would be compromised.
Bits [14–3]—Reserved.
Bits [2–0]—TMR [2–0] Timer Interrupt Request → When any of these bits is 1,
a pending interrupt request is indicated by the respective timer.
Note: The TMR bit in the REQST register is a logical OR of these timer
interrupt requests.
5.1.43 INTSTS (030h) (Slave Mode)
When NMIs occur, the interrupt status register controls DMA operation and the interrupt request
status of each of the three timers, Timer2, Timer1, and Timer0 (see Table 64).
Table 64. Interrupt Status Register (Slave Mode)
15
DHLT
14
13
12
®
11
10 9 8
Reserved
7
6
5
4
3
2
1
0
TMR2–TMR0
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 99 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [15]—DHLT DMA Halt → DMA activity is halted when this bit is 1. It is set to 1
automatically when any non-maskable interrupt occurs and is cleared to 0 when an IRET
instruction is executed. Interrupt handlers and other time critical software may modify
this bit directly to disable DMA transfers. However, the DHLT bit should not be
modified by software if the timer interrupts are enabled as the function of this register as
an interrupt request register for the timers would be compromised.
Bits [14–3]—Reserved.
Bit [2–0]—TMR [2–0] Timer Interrupt Request → A pending interrupt request is
indicated by the respective timer, when any of these bits is 1.
Note: The TMR bit in the REQST register is a logical OR of these timer
interrupt requests.
5.1.44 REQST (02eh) (Master Mode)
Interrupt REQueST Register. This is a read-only register and such a read results in the status of
the interrupt request bits presented to the interrupt controller. The REQST register is undefined
on reset (see Table 65).
Table 65. Interrupt Request Register (Master Mode)
15
14 13 12
Reserved
11
10
SP0
9
SP1
8
I4
7
I3
6
I2
5
I1
4
IO
3
D1/I6
2
D0/I5
1
Res
0
TMR
Bits [15–11]—Reserved.
Bit [10]—SP0 Serial Port 0 Interrupt Request → This is the serial port 0 interrupt state
and when enabled is the logical OR of all the serial port 0 interrupt sources, THRE, RDR,
BRK1, BRK0, FER, PER, and OER.
Bit [9]—SP1 Serial Port 1 Interrupt Request → This is the serial port 1 interrupt state and
when enabled is the logical OR of all the serial port 1 interrupt sources, THRE, RDR,
BRK1, BRK0, FER, PER, and OER.
Bits [8–4]—I [4–0] Interrupt Requests → When any of these bits is set to 1, it indicates
that the relevant interrupt has a pending interrupt.
Bit [3]—D1/I6 DMA Channel 1/Interrupt 6 Request → When set to 1, it indicates that
either the DMA channel 1 or int6 has a pending interrupt.
Bit [2]—D0/I5 DMA Channel 0/Interrupt 5 Request → When set to 1, it indicates that
either the DMA channel 0 or int5 has a pending interrupt.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 100 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [1]—Reserved.
Bit [0]—TMR Timer Interrupt Request → This is the timer interrupt state and is the
logical OR of the timer interrupt requests. When set to 1, it indicates that the timer
control unit has a pending interrupt.
5.1.45 REQST (02eh) (Slave Mode)
This read-only register results in the status of interrupt request bits being presented to the
interrupt controller. The status of these bits is available when this register is read. This register
is read-only.
When an internal interrupt request (D1/I6, D0/I5, TMR2, TMR1, or TMR0) occurs, the
respective bit is set to 1. The internally generated interrupt acknowledge resets these bits. The
REQST register contains 0000h on reset (see Table 66).
Table 66. Interrupt Request Register (Slave Mode)
15
14
13
12 11 10
Reserved
9
8
7
6
5
TMR2
4
TMR1
3
D1/I6
2
D0/I5
1
Res
0
TMR0
Bits [15–6]—Reserved.
Bit [5]—TMR2 Interrupt Requests → When set to 1, it indicates that Timer2 has a
pending interrupt.
Bit [4]—TMR1 Interrupt Requests → When set to 1, it indicates that Timer1 has a
pending interrupt.
Bit [3]—D1/I6 DMA Channel 1/Interrupt 6 Request → When set to 1, it indicates that
either the DMA channel 1 or int6 has a pending interrupt.
Bit [2]—D0/I5 DMA Channel 0/Interrupt 5 Request → When set to 1, it indicates that
either the DMA channel 0 or int5 has a pending interrupt.
Bit [1]—Reserved.
Bit [0]—TMR0 Timer Interrupt Request → When set to 1, it indicates that Timer0 has a
pending interrupt.
5.1.46 INSERV (02ch) (Master Mode)
IN-SERVice Register. The interrupt controller sets the bits in this register when the interrupt is
taken. The INSERV register contains 0000h on reset (see Table 67).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 101 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 67. In-Service Register (Master Mode)
15
14 13 12
Reserved
11
10
SP0
9
SP1
8
I4
7
I3
6
I2
5
I1
4
IO
3
D1/I6
2
D0/I5
1
Res
0
TMR
Bits [15–11]—Reserved.
Bit [10]—SP0 Serial Port 0 Interrupt Request → This is the Serial Port 0 interrupt state.
Bit [9]—SP1 Serial Port 1 Interrupt Request → This is the Serial Port 1 interrupt state.
Bits [8–4]—I [4–0] Interrupt Requests → When any of these bits is set to 1, it indicates
that the relevant interrupt has a pending interrupt.
Bit [3]—D1/I6 DMA Channel 1/Interrupt 6 Request → When set to 1, it indicates that
either the DMA channel 1 or int6 has a pending interrupt.
Bit [2]—D0/I5 DMA Channel 0/Interrupt 5 Request → When set to 1 it indicates that
either the DMA channel 0 or int5 has a pending interrupt.
Bit [1]—Reserved.
Bit [0]—TMR Timer Interrupt Request → This is the timer interrupt state and is the
logical OR of the timer interrupt requests. When set to 1, it indicates that the timer
control unit has a pending interrupt.
5.1.47 INSERV (02ch) (Slave Mode)
This read-only register results in the status of interrupt request bits being presented to the
interrupt controller. The status of these bits is available when this register is read. This register
is read-only.
When an internal interrupt request (D1/I6, D0/I5, TMR2, TMR1, and TMR0) occurs, the
respective bit is set to 1. The internally generated interrupt acknowledge resets these bits. The
REQST register contains 0000h on reset (see Table 68).
Table 68. In-Service Register (Slave Mode)
15
14
13
12 11 10
Reserved
9
8
7
6
5
TMR2
4
TMR1
3
D1/I6
2
D0/I5
1
Res
0
TMR0
Bits [15–6]—Reserved.
Bit [5]—TMR2 Timer2 Interrupt In Service → Timer2 is being serviced when this bit is
set to 1.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 102 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [4]—TMR1 Timer1 Interrupt IN Service → Timer1 is being serviced when this bit is
set to 1.
Bit [3]—D1/I6 DMA Channel Interrupt 6 In Service → DMA channel 1 or int6 is being
serviced when this bit is set to 1.
Bit [2]—D0/I5 DMA Channel Interrupt 5 IN Service → DMA channel 0 or int5 is being
serviced when this bit is set to 1.
Bit [1]—Reserved.
Bit [0]—TMR0 Timer Interrupt In Service → Timer0 is being serviced when this bit is
set to 1.
5.1.48 PRIMSK (02ah) (Master and Slave Mode)
PRIority MaSK Register. This register contains a value that sets the minimum priority level that
a maskable interrupt must have to generate an interrupt. The PRIMSK register contains 0007h
on reset (see Table 69).
Table 69. Priority Mask Register
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
1
0
PRM2–PRM0
Bits [15–3]—Reserved. Set to 0.
Bits [2–0]—PRM [2–0] Priority Field Mask → This three-bit field sets the minimum
priority necessary for a maskable interrupt to generate an interrupt. Any maskable
interrupt with a numerically higher value than that contained by these three bits, are
masked. The values of PR2–PR0 are shown above.
–
Any unmasked interrupt may generate an interrupt if the priority level is set to 7.
However, by way of example, if the priority level is set to 4, only unmasked
interrupts with a priority of 0 to 5 are permitted to generate interrupts.
5.1.49 IMASK (028h) (Master Mode)
Interrupt MASK Register. The interrupt mask register is read/write. Setting a bit in this register
is effectively the same as setting the MSK bit in the corresponding interrupt control register.
Setting a bit to 1 masks the interrupt. The interrupt request is enabled when the corresponding
bit is set to 0. The IMASK register contains 07fdh on reset (see Table 70).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 103 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 70. Interrupt MASK Register (Master Mode)
15
14 13 12
Reserved
11
10
SP0
9
SP1
8
I4
7
I3
6
I2
5
I1
4
IO
3
D1/I6
2
D0/I5
1
Res
0
TMR
Bits [15–11]—Reserved.
Bit [10]—SP0 Serial Port 0 Interrupt Mask → Setting this bit to 1 is an indication that the
serial port 0 interrupt is masked.
Bit [9]—SP1 Serial Port 1 Interrupt Mask → Setting this bit to 1 is an indication that the
serial port 0 interrupt is masked.
Bits [8–4]—I [4–0] Interrupt Mask → When any of these bits is set to 1, it is an
indication that the relevant interrupt is masked.
Bit [3]—D1/I6 DMA Channel 1/Interrupt 6 Mask → Setting this bit to 1, is an indication
that either the DMA channel 1 or int6 interrupt is masked.
Bit [2]—D0/I5 DMA Channel 0/Interrupt 5 Mask → When set to 1, it indicates that either
the DMA channel 0 or int5 interrupt is masked.
Bit [1]—Reserved.
Bit [0]—TMR Timer Interrupt Mask → When set to 1, it indicates that the timer control
unit interrupt is masked.
5.1.50 IMASK (028h) (Slave Mode)
The interrupt mask register is read/write. Setting a bit in this register has the effect of setting the
MSK bit in the corresponding interrupt control register. Setting a bit to 1, masks the interrupt
request. The interrupt request is enabled when the corresponding bit is set to 0. The IMASK
register contains 003dh on reset (see Table 71).
Table 71. Interrupt MASK Register (Slave Mode)
15
14
13
12 11 10
Reserved
9
8
7
6
5
TMR2
4
TMR1
3
D1/I6
2
D0/I5
1
Res
0
TMR0
Bits [15–6]—Reserved.
Bit [5]—TMR2 Timer2 Interrupt Mask → This bit provides the state of the mask bit in
the Timer Interrupt Control register. When set to 1, it indicates that the interrupt request
is masked.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 104 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bit [4]—TMR1 Timer1 Interrupt Mask → This bit provides the state of the mask bit in
the Timer Interrupt Control register. When set to 1, it indicates that the interrupt request
is masked.
Bit [3]—D1/I6 DMA Channel Interrupt 6 Mask → This bit provides the state of the mask
bit in the DMA channel 0 or int5 Interrupt Control register. When set to 1, it indicates
that the interrupt request is masked.
Bit [2]—D0/I5 DMA Channel Interrupt 5 Mask → This bit provides the state of the mask
bit in the DMA channel 1 or int6 Interrupt Control register. When set to 1, it indicates
that the interrupt request is masked.
Bit [0]—TMR0 Timer Interrupt Mask → This bit provides the state of the mask bit in the
Timer Interrupt Control register. When set to 1, it indicates that the interrupt request is
masked.
5.1.51 POLLST (026h) (Master Mode)
POLL STatus Register. This register reflects the current state of the poll register and can be read
without affecting its contents. However, the current interrupt is acknowledged and replaced by
the next interrupt when the poll register is read. The poll status register is read-only (see
Table 72).
Table 72. POLL Status Register
15
IREQ
14
13
12
11 10 9
Reserved
8
7
6
5
4
3 2 1
S4–S0
0
Bit [15]—IREQ Interrupt Request → This bit is set to 1 when an interrupt is pending and
during this state, the S4–S0 bits contain valid data.
Bits [14–6]—Reserved.
Bit [5–0]—S [5–0] Poll Status → These bits show the interrupt type of the highest
priority pending interrupt.
5.1.52 POLL (024h) (Master Mode)
POLL Register. The current interrupt is acknowledged and replaced by the next interrupt when
the poll register is read. The poll status register reflects the current state of the poll register and
can be read without affecting its contents. The poll register is read-only (see Table 73).
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 105 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 73. Poll Register
15
IREQ
14
13
12
11 10 9
Reserved
8
7
6
5
4
3 2 1
S4–S0
0
Bit [15]—IREQ Interrupt Request → This bit is set to 1 when an interrupt is pending and
during this state, the S4–S0 bits contain valid data.
Bits [14–6]—Reserved.
Bit [4–0]—S [4–0] Poll Status → These bits show the interrupt type of the highest
priority pending interrupt.
5.1.53 EOI (022h) End-Of-Interrupt Register (Master Mode)
The In Service flags of the INSERV register are reset when a write is made to the EOI register.
The interrupt service routine (ISR) should write to the EOI to reset the IS bit, in the INSERV
register, for the interrupt before executing an IRET instruction than ends an interrupt service
routine. Because it is the most secure, the specific EOI reset is the preferred method for resetting
the IS bits. The EOI register is write-only (see Table 74).
Table 74. End-Of-Interrupt Register
15
NSPEC
14
13
12
11 10 9
Reserved
8
7
6
5
4
3 2 1
S4–S0
0
Bit [15]—NSPEQ Non-Specific EOI → When set to 1, this bit is a non-specific EOI.
When 0, it indicates the specific EOI.
Bits [14–5]—Reserved.
Bit [4–0]—S [4–0] Source Interrupt Type → These bits show the interrupt type of the
highest priority pending interrupt.
5.1.54 EOI (022h) Specific End-Of-Interrupt Register (Slave Mode)
Specific End-Of-Interrupt Register. An In Service flag of a specific priority in the INSERV
register is reset when a write is made to the EOI register. A three-bit, user-supplied priority-level
value points to the in-service bit that is to be reset. Writing this value to this register resets the
specific bit. Because it is the most secure, the specific EOI reset is the preferred method for
resetting the IS bits. The EOI register is write-only and undefined at reset (see Table 75).
Table 75. Specific End-Of-Interrupt Register
15
0
14
0
13
0
12
0
11
0
®
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
1 0
L2–L0
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 106 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Bits [15–3]—Reserved. Write as 0.
Bit [2–0]—L [2–0] Interrupt Type → The priority or the IS (interrupt service) bit to be
reset is encoded in these three bits. Writing to these bits causes the issuance of an EOI
for the interrupt type (see Table 14, Interrupt Types).
5.1.55 INTVEC (020h) Interrupt Vector Register (Slave Mode)
The CPU shifts left 2 bits (i.e., it multiplies by 4) an 8-bit interrupt type, generated by the
interrupt controller, to produce an offset into the interrupt vector table. The INTVEC register is
undefined at reset (see Table 76).
Table 76. Interrupt Vector Register
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
6 5 4
T4–T0
3
2
0
1
0
0
0
Bits [15–8]—Reserved. Read as 0.
Bits [7–3]—T [4–0] Interrupt Type → These five bits contain the five most significant
bits of the types used for the internal interrupt. The least significant three bits of the
interrupt type are supplied by the interrupt controller, as set by the priority level of the
interrupt request.
Bits [2–0]—Reserved. Read as 0.
5.2
Reference Documents
Additional information on the operation and programming of the IA186ES/ IA188ES can be
found in the following AMD publications:
Am186 ES and Am188 ES User’s Manual (Publication 21096).
Am186
ES/ESLV and Am188
®
ES/ESLV Preliminary Data Sheet (Publication 20002).
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 107 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
6.
Data Sheet
November 15, 2011
AC Specifications
Table 77 and Table 78 present the alphabetic and numeric keys to waveform parameters,
respectively. Figure 12 presents the read cycle. Figure 13 presents the multiple read cycles.
Table 79 presents the read cycle timing. Figure 14 presents the write cycle. Table 80 presents
the write cycle timing. Figure 15 presents the multiple write cycles.
Figure 16 presents the PSRAM read cycle. Table 81 presents the PSRAM read cycle timing.
Figure 17 presents the PSRAM write cycle. Table 82 presents the PSRAM write cycle timing.
Figure 18 presents the PSRAM refresh cycle. Table 83 presents the PSRAM refresh cycle
timing. Figure 19 presents the interrupt acknowledge cycle. Table 84 presents the interrupt
acknowledge cycle timing. Figure 20 presents the software halt cycle. Table 85 presents the
software halt cycle timing. Figure 21 presents the active mode. Figure 22 presents the powersave mode. Table 86 presents the clock timing.
Figure 23 presents the srdy—synchronous ready. Figure 24 presents the ardy—asynchronous
ready. Figure 25 presents the peripherals. Table 87 presents the ready and peripheral timing.
Figure 26 and Figure 27 present Reset 1 and Reset 2, respectively. Figure 28 and Figure 29
present the bus hold entering and bus hold leaving, respectively. Table 88 presents the reset and
bus hold timing.
Table 77. Alphabetic Key to Waveform Parameters
No.
49
51
52
87
14
12
66
65
24
45
68
38
44
67
18
22
64
63
aIn
Name
tARYCH
tARYCHL
tARYLCL
tAVBL
tAVCH
tAVLL
tAVRL
tAVWL
tAZRL
tCH1CH2
tCHAV
tCHCK
tCHCL
tCHCSV
tCHCSX
tCHCTV
tCHCV
tCHCZ
Description
ardy Resolution Transition Setup Time
ardy Inactive Holding Time
ardy Setup Time
a Address Valid to whb_n/wlb_n Low
ad Address Valid to Clock High
ad Address Valid to ale Low
a Address Valid to rd_n Low
a Address Valid to wr_n Low
ad Address Float to rd_n Active
clkouta Rise Time
clkouta High to a Address Valid
x1 High Time
clkouta High Time
clkouta High to lcs_n/usc_n Valid
mcs_n/pcs_n Inactive Delay
Control Active Delay 2
Command Lines Valid Delay (after Float)
Command Lines Float Delay
Mina
9
6
9
tCHCL-1.5
0
tCHCL
tCLCL+tCHCL
tCLCL+tCHCL
0
0
0
7.5
tCLCL/2
0
0
0
0
0
Maxa
–
–
–
tCHCL
–
–
–
–
–
3
8
–
–
9
12
10
12
12
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 108 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 77. Alphabetic Key to Waveform Parameters (Continued)
No.
8
9
11
79
3
69
70
39
36
40
46
50
5
6
15
43
37
42
80
81
16
30
7
2
62
82
27
25
4
48
55
83
20
31
21
17
98
41
aIn
Name
tCHDX
tCHLH
tCHLL
tCHRFD
tCHSV
tCICOA
tCICOB
tCKHL
tCKIN
tCKLH
tCL2CL1
tCLARX
tCLAV
tCLAX
tCLAZ
tCLCH
tCLCK
tCLCL
tCLCLX
tCLCSL
tCLCSV
tCLDOX
tCLDV
tCLDX
tCLHAV
tCLRF
tCLRH
tCLRL
tCLSH
tCLSRY
tCLTMV
tCOAOB
tCVCTV
tCVCTX
tCVDEX
tCXCSX
tDSHDIW
tDSHLH
Description
Status Hold Time
ale Active Delay
ale Inactive Delay
clkouta High to rfsh_n Valid
Status Active Delay
x1 to clkouta Skew
x1 to clkoutb Skew
x1 Fall Time
x1 Period
x1 Rise time
clkouta Fall Time
ardy Active Hold Time
ad Address Valid Delay
Address Hold
ad Address Float Delay
clkouta Low Time
x1 Low Time
clkouta Period
lcs_n Inactive Delay
lcs_n Active Delay
mcs_n/pcs_n Inactive Delay
Data Hold Time
Data Valid Delay
Data in Hold
hlda Valid Delay
clkouta High to rfsh_n Invalid
rd_n Inactive Delay
rd_n Active Delay
Status Inactive Delay
srdy Transition Hold Time
Timer Output Delay
clkouta to clkoutb Skew
Control Active Delay 1
Control Inactive Delay
den_n Inactive Delay
mcs_n/pcs_n Hold from Command Inactive
ds_n High to Data Invalid (Write)
ds_n Inactive to ale Inactive
Mina
0
0
0
0
0
–
–
–
25
–
–
4
0
0
0
tCLCL/2
7.5
25
0
0
0
0
0
0
0
0
0
0
0
3
0
3
–
0
0
tCLCH
0
tCLCH
Maxa
–
8
8
12
6
25
35
5
66
5
3
–
12
12
12
–
–
–
9
9
12
–
12
–
7
12
10
10
6
–
12
1
10
10
9
–
tCHCL
–
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 109 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 77. Alphabetic Key to Waveform Parameters (Continued)
No.
1
19
58
53
54
86
23
10
13
61
84
57
85
29
59
28
26
47
35
34
33
32
aIn
Name
tDVCL
tDXDL
tHVCL
tINVCH
tINVCL
tLCRF
tLHAV
tLHLL
tLLAX
tLOCK
tLRLL
tRESIN
tRFCY
tRHAV
tRHDX
tRHLH
tRLRH
tSRYCL
tWHDEX
tWHDX
tWHLH
tWLWH
Description
Data in Setup
den_n Inactive to dt/r_n Low
hld Setup Time
Peripheral Setup Time
drq Setup Time
lcs_n Inactive to rfsh_n Active Delay
ale High to Address Valid
ale Width
ad Address Hold from ale Inactive
Maximum PLL Lock Time
lcs_n Precharge Pulse Width
res_n Setup Time
rfsh_n Cycle Time
rd_n Inactive to ad Address Active
rd_n High to Data Hold on ad Bus
rd_n Inactive to ale High
rd_n Pulse Width
srdy Transition Setup Time
wr_n Inactive to den_n Inactive
Data Hold after wr_n
wr_n Inactive to ale High
wr_n Pulse Width
Mina
10
0
10
10
10
2tCLCL
7.5
tCLCH-5
tCHCL
–
tCLCL+tCLCHH
10
6tCLCL
tCLCL
0
tCLCH
tCLCL
10
tCLCH
tCLCL
tCLCH
2tCLCL
Maxa
–
–
–
–
–
–
–
–
–
0.5
–
–
–
–
–
–
–
–
–
–
–
–
nanoseconds.
Table 78. Numeric Key to Waveform Parameters
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
aIn
Name
tDVCL
tCLDX
tCHSV
tCLSH
tCLAV
tCLAX
tCLDV
tCHDX
tCHLH
tLHLL
tCHLL
tAVLL
tLLAX
Mina
10
0
0
0
0
0
0
0
0
tCLCH-5
0
tCLCH
tCHCL
Description
Data in Setup
Data in Hold
Status Active Delay
Status Inactive Delay
ad Address Valid Delay
Address Hold
Data Valid Delay
Status Hold Time
ale Active Delay
ale Width
ale Inactive Delay
ad Address Valid to ale Low
ad Address Hold from ale Inactive
Maxa
–
–
6
6
12
12
12
–
8
–
8
–
–
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 110 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 78. Numeric Key to Waveform Parameters (Continued)
No.
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
aIn
Name
Description
tAVCH ad Address Valid to Clock High
tCLAZ
ad Address Float Delay
tCLCSV mcs_n/pcs_n Inactive Delay
tCXCSX mcs_n/pcs_n Hold from Command Inactive
tCHCSX mcs_n/pcs_n Inactive Delay
tDXDL
den_n Inactive to dt/r_n Low
tCVCTV Control Active Delay 1
tCVDEX den_n Inactive Delay
tCHCTV Control Active Delay 2
tLHAV
ale High to Address Valid
ad Address Float to rd_n Active
tAZRL
tCLRL
rd_n Active Delay
tRLRH rd_n Pulse Width
tCLRH rd_n Inactive Delay
tRHLH rd_n Inactive to ale High
tRHAV rd_n Inactive to ad Address Active
tCLDOX Data Hold Time
tCVCTX Control Inactive Delay
tWLWH wr_n Pulse Width
tWHLH wr_n Inactive to ale High
tWHDX Data Hold after wr_n
tWHDEX wr_n Inactive to den_n Inactive
tCKIN
x1 Period
tCLCK
x1 Low Time
tCHCK x1 High Time
tCKHL
x1 Fall Time
tCKLH
x1 Rise time
tDSHLH ds_n Inactive to ale Inactive
tCLCL
clkouta Period
tCLCH clkouta Low Time
tCHCL clkouta High Time
tCH1CH2 clkouta Rise Time
tCL2CL1 clkouta Fall Time
tSRYCL srdy Transition Setup Time
tCLSRY srdy Transition Hold Time
tARYCH ardy Resolution Transition Setup Time
tCLARX ardy Active Hold Time
tARYCHL ardy Inactive Holding Time
Mina
0
0
0
tCLCH
0
0
0
0
0
7.5
0
0
tCLCL
0
tCLCH
tCLCL
0
0
2tCLCL
tCLCH
tCLCL
tCLCH
25
7.5
7.5
–
–
tCLCH
25
tCLCL/2
tCLCL/2
–
–
10
3
9
4
6
Maxa
–
12
12
–
12
–
10
9
10
–
–
10
–
10
–
–
–
10
–
–
–
–
66
–
–
5
5
–
–
–
–
3
3
–
–
–
–
–
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 111 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 78. Numeric Key to Waveform Parameters (Continued)
No.
52
53
54
55
57
58
59
61
62
63
64
65
66
67
68
69
70
79
80
81
82
83
84
85
86
87
98
99
aIn
Name
Description
tARYLCL ardy Setup Time
tINVCH Peripheral Setup Time
tINVCL drq Setup Time
tCLTMV Timer Output Delay
tRESIN res_n Setup Time
tHVCL
hld Setup Time
tRHDX rd_n High to Data Hold on ad Bus
tLOCK
Maximum PLL Lock Time
tCLHAV hlda Valid Delay
tCHCZ Command Lines Float Delay
tCHCV Command Lines Valid Delay (after Float)
tAVWL a Address Valid to wr_n Low
tAVRL
a Address Valid to rd_n Low
tCHCSV clkouta High to lcs_n/usc_n Valid
tCHAV clkouta High to a Address Valid
tCICOA x1 to clkouta Skew
tCICOB x1 to clkoutb Skew
tCHRFD clkouta High to rfsh_n Valid
tCLCLX lcs_n Inactive Delay
tCLCSL lcs_n Active Delay
tCLRF
clkouta High to rfsh_n Invalid
tCOAOB clkouta to clkoutb Skew
tLRLL
lcs_n Precharge Pulse Width
tRFCY rfsh_n Cycle Time
tLCRF
lcs_n Inactive to rfsh_n Active Delay
tAVBL
a Address Valid to whb_n/wlb_n Low
tDSHDIW ds_n High to Data Invalid (Write)
tPLAL
pcs Low to ale Low
Mina
9
10
10
0
10
10
0
–
0
0
0
tCLCL+tCHCL
tCLCL+tCHCL
0
0
–
–
0
0
0
0
3
tCLCL+tCLCH
6tCLCL
2tCLCL
tCHCL-1.5
0
–
Maxa
–
–
–
12
–
–
–
0.5
7
12
12
–
–
9
8
25
35
12
9
9
12
11
–
–
–
tCHCL
tCLCL
tCLCH
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 112 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
clkouta
a19–a0
s6/lock_n
ad15–ad0 (IA186ES),
ad7–ad0 (IA188ES)
ao15–ao8 (IA188ES)
ale
rd_n
bhe_n (IA186ES)
lcs_n, ucs_n
mcs_n, pcs_n
den_n/ds_n
dt/r_n
s2_n–s0_n
uzi_n
Figure 12. Read Cycle
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 113 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
clkouta
a19–a0
ad15–ad0 (IA186ES),
ao15–ao8 (IA188ES)
ale
rd_n
lcs_n, ucs_n
mcs_n, pcs_n
s2_n–s0_n
Figure 13. Multiple Read Cycles
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 114 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 79. Read Cycle Timing
No.
Name
Description
General Timing Requirements
1
tDVCL
Data in Setup
2
tCLDX
Data in Hold
General Timing Responses
3
tCHSV
Status Active Delay
4
tCLSH
Status Inactive Delay
5
tCLAV
ad Address Valid Delay
6
tCLAX
Address Hold
8
tCHDX
Status Hold Time
9
tCHLH
ale Active Delay
10 tLHLL
ale Width
11 tCHLL
ale Inactive Delay
12 tAVLL
ad Address Valid to ale Low
13 tLLAX
ad Address Hold from ale Inactive
14 tAVCH
ad Address Valid to Clock High
15 tCLAZ
ad Address Float Delay
16 tCLCSV
mcs_n/pcs_n Inactive Delay
17 tCXCSX
mcs_n/pcs_n Hold from Command Inactive
18 tCHCSX
mcs_n/pcs_n Inactive Delay
19 tDXDL
den_n Inactive to dt/r_n Low
20 tCVCTV
Control Active Delay 1
21 tCVDEX
den_n Inactive Delay
22 tCHCTV
Control Active Delay 2
23 tLHAV
ale High to Address Valid
99 tPLAL
pcs Low to ale Low
Read Cycle Timing Responses
24 tAZRL
ad Address Float to rd_n Active
25 tCLRL
rd_n Active Delay
26 tRLRH
rd_n Pulse Width
27 tCLRH
rd_n Inactive Delay
28 tRHLH
rd_n Inactive to ale High
29 tRHAV
rd_n Inactive to ad Address Active
41 tDSHLH
ds_n Inactive to ale Inactive
59 tRHDX
rd_n High to Data Hold on ad Bus
66 tAVRL
a Address Valid to rd_n Low
67 tCHCSV
clkouta High to lcs_n/usc_n Valid
68 tCHAV
clkouta High to a Address Valid
aIn
Mina
Maxa
10
0
–
–
0
0
0
0
0
0
tCLCH-5
0
tCLCH
tCHCL
0
0
0
tCLCH
0
0
0
0
0
7.5
–
6
6
12
12
–
8
–
8
–
–
–
12
12
–
12
–
10
9
10
–
tCLCH
0
0
tCLCL
0
tCLCH
tCLCL
tCLCH
0
tCLCL+tCHCL
0
0
–
10
–
10
–
–
–
–
–
9
8
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 115 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
clkouta
a19–a0
s6/lock_n
ad15–ad0 (IA186ES),
ad7–ad0 (IA188ES)
ao15–ao8 (IA188ES)
ale
wr_n
whb_n, wlb_n (IA186ES),
wb_n (IA188ES)
bhe_n (IA186ES)
lcs_n, ucs_n
mcs_n, pcs_n
den_n/ds_n
dt/r_n
s2_n–s0_n
uzi_n
Figure 14. Write Cycle
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 116 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
clkouta
a19–a0
ad15–ad0 (IA186ES),
ao15–ao8 (IA188ES)
ale
rd_n
lcs_n, ucs_n
mcs_n, pcs_n
s2_n–s0_n
Figure 15. Multiple Write Cycles
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 117 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 80. Write Cycle Timing
No.
Name
Description
General Timing Requirements
1
tDVCL
Data in Setup
2
tCLDX
Data in Hold
General Timing Responses
3
tCHSV
Status Active Delay
4
tCLSH
Status Inactive Delay
ad Address Valid Delay
5
tCLAV
6
tCLAX
Address Hold
8
tCHDX
Status Hold Time
9
tCHLH
ale Active Delay
10 tLHLL
ale Width
11 tCHLL
ale Inactive Delay
ad Address Valid to ale Low
12 tAVLL
ad Address Hold from ale Inactive
13 tLLAX
ad Address Valid to Clock High
14 tAVCH
ad Address Float Delay
15 tCLAZ
16 tCLCSV
mcs_n/pcs_n Inactive Delay
17 tCXCSX
mcs_n/pcs_n Hold from Command Inactive
18 tCHCSX
mcs_n/pcs_n Inactive Delay
19 tDXDL
den_n Inactive to dt/r_n Low
20 tCVCTV
Control Active Delay 1
21 tCVDEX
den_n Inactive Delay
22 tCHCTV
Control Active Delay 2
23 tLHAV
ale High to Address Valid
99 tPLAL
pcs Low to ale Low
Write Cycle Timing Responses
30 tCLDOX
Data Hold Time
31 tCVCTX
Control Inactive Delay
32 tWLWH
wr_n Pulse Width
33 tWHLH
wr_n Inactive to ale High
34 tWHDX
Data Hold after wr_n
35 tWHDEX
wr_n Inactive to den_n Inactive
41 tDSHLH
ds_n Inactive to ale Inactive
a Address Valid to wr_n Low
65 tAVWL
67 tCHCSV
clkouta High to lcs_n/usc_n Valid
68 tCHAV
clkouta High to a Address Valid
a Address Valid to whb_n/wlb_n Low
87 tAVBL
98 tDSHDIW
ds_n High to Data Invalid (Write)
aIn
Mina
Maxa
10
0
–
–
0
0
0
0
0
0
tCLCH-5
0
tCLCH
tCHCL
0
0
0
tCLCH
0
0
0
0
0
7.5
–
6
6
12
12
–
8
–
8
–
–
–
12
12
–
12
–
10
9
10
–
tCLCH
0
0
2tCLCL
tCLCH
tCLCL
tCLCH
tCLCH
tCLCL+tCHCL
0
0
tCHCL-1.5
0
–
10
–
–
–
–
–
–
9
8
tCHCL
tCLCL
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 118 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
0ns
Data Sheet
November 15, 2011
20ns
40ns
60ns
80ns
100ns
120ns
140ns
160ns
clkouta
66
Address
a19–a0
68
_
s6/lock_n
8
s6
lock_n
s6
5
ad15–ad0 (IA186ES),
ad7–ad0 (IA188ES)
7
1
Address
Data
23
Address
2
Address
ao15–ao8 (IA188ES)
9
11
59
le
alea
24
10
28
25
27
rd_n
84
26
81
80
lcs_nn
Figure 16. PSRAM Read Cycle
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 119 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 81. PSRAM Read Cycle Timing
No.
Name
Description
General Timing Requirements
1
tDVCL
Data in Setup
2
tCLDX
Data in Hold
General Timing Responses
ad Address Valid Delay
5
tCLAV
6
tCLAX
Address Hold
8
tCHDX
Status Hold Time
9
tCHLH
ale Active Delay
10 tLHLL
ale Width
11 tCHLL
ale Inactive Delay
ad Address Valid to ale Low
12 tAVLL
ad Address Hold from ale Inactive
13 tLLAX
ad Address Valid to Clock High
14 tAVCH
ad Address Float Delay
15 tCLAZ
16 tCLCSV
mcs_n/pcs_n Inactive Delay
17 tCXCSX
mcs_n/pcs_n Hold from Command Inactive
18 tCHCSX
mcs_n/pcs_n Inactive Delay
19 tDXDL
den_n Inactive to dt/r_n Low
20 tCVCTV
Control Active Delay 1
21 tCVDEX
den_n Inactive Delay
22 tCHCTV
Control Active Delay 2
23 tLHAV
ale High to Address Valid
99 tPLAL
pcs Low to ale Low
Read Cycle Timing Responses
30 tCLDOX
Data Hold Time
31 tCVCTX
Control Inactive Delay
32 tWLWH
wr_n Pulse Width
33 tWHLH
wr_n Inactive to ale High
34 tWHDX
Data Hold after wr_n
35 tWHDEX
wr_n Inactive to den_n Inactive
41 tDSHLH
ds_n Inactive to ale Inactive
a Address Valid to wr_n Low
65 tAVWL
67 tCHCSV
clkouta High to lcs_n/usc_n Valid
68 tCHAV
clkouta High to a Address Valid
a Address Valid to whb_n/wlb_n Low
87 tAVBL
98 tDSHDIW
ds_n High to Data Invalid (Write)
aIn
Mina
Maxa
10
0
–
–
0
0
0
0
tCLCH-5
0
tCLCH
tCHCL
0
0
0
tCLCH
0
0
0
0
0
7.5
–
12
12
–
8
–
8
–
–
–
12
12
–
12
–
10
9
10
–
tCLCH
0
0
2tCLCL
tCLCH
tCLCL
tCLCH
tCLCH
tCLCL +tCHCL
0
0
tCHCL-1.5
0
–
10
–
–
–
–
–
–
9
8
tCHCL
tCLCL
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 120 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
0ns
Data Sheet
November 15, 2011
20ns
40ns
60ns
80ns
100ns
120ns
140ns
160ns
180ns
clkouta
65
Address
a19–a0
68
n
_
k
c
s6/lock_n
8
s6
lock_n
5
ad15–ad0 (IA186ES),
0
ad7–ad0 (IA188ES)d
ao15–ao8 (IA188ES)
s6
7
30
Address
Data
Address
23
33
9
11
34
le
alea
31
10
20
31
n
r_
wr_nw
87
20
whb_n, wlb_n
n
(IA186ES), wb_n_
(IA188ES)
80
32
81
84
80
lcs_nlcs_
n
Figure 17. PSRAM Write Cycle
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 121 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 82. PSRAM Write Cycle Timing
No.
Name
Description
General Timing Requirements
1
tDVCL
Data in Setup
2
tCLDX
Data in Hold
General Timing Responses
ad Address Valid Delay
5
tCLAV
7
tCLDV
Data Valid Delay
8
tCHDX
Status Hold Time
9
tCHLH
ale Active Delay
10 tLHLL
ale Width
11 tCHLL
ale Inactive Delay
20 tCVCTV
Control Active Delay 1
23 tLHAV
ale High to Address Valid
80 tCLCLX
lcs_n Inactive Delay
81 tCLCSL
lcs_n Active Delay
84 tLRLL
lcs_n Precharge Pulse Width
Write Cycle Timing Responses
30 tCLDOX
Data Hold Time
31 tCVCTX
Control Inactive Delay
32 tWLWH
wr_n Pulse Width
33 tWHLH
wr_n Inactive to ale High
34 tWHDX
Data Hold after wr_n
a Address Valid to wr_n Low
65 tAVWL
68 tCHAV
clkouta High to a Address Valid
a Address Valid to whb_n/wlb_n Low
87 tAVBL
aIn
Mina
Maxa
10
0
–
–
0
0
0
0
tCLCH-5
0
0
7.5
0
0
tCLCL+tCLCH
12
12
–
8
–
8
10
–
9
9
–
0
0
2tCLCL
tCLCH
tCLCL
tCLCL+tCHCL
0
tCHCL-1.5
–
10
–
–
–
–
8
tCHCL
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 122 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
0ns
20ns
Data Sheet
November 15, 2011
40ns
60ns
80ns
100ns
120ns
140ns
160ns
180ns
0
K
L
clk0C
-0
9
1
a19–a0a
Address
9
11
28
alea
le
27
10
26
rd_nrd
n
_
80
25
27
81
lcs_n
79
82
_
rfsh_nrfsh
86
85
Figure 18. PSRAM Refresh Cycle
Table 83. PSRAM Refresh Cycle Timing
No.
Name
Description
General Timing Requirements
1
tDVCL
Data in Setup
2
tCLDX
Data in Hold
General Timing Responses
9
tCHLH
ale Active Delay
10 tLHLL
ale Width
11 tCHLL
ale Inactive Delay
Read/Write Cycle Timing Responses
25 tCLRL
rd_n Active Delay
26 tRLRH
rd_n Pulse Width
27 tCLRH
rd_n Inactive Delay
28 tRHLH
rd_n Inactive to ale High
80 tCLCLX
lcs_n Inactive Delay
81 tCLCSL
lcs_n Active Delay
Refresh Cycle Timing Responses
79 tCHRFD
clkouta High to rfsh_n Valid
82 tCLRF
clkouta High to rfsh_n Invalid
85 tRFCY
rfsh_n Cycle Time
86 tLCRF
lcs_n Inactive to rfsh_n Active Delay
aIn
Mina
Maxa
10
0
–
–
0
tCLCH-5
0
8
–
8
0
tCLCL
0
tCLCH
0
0
10
–
10
–
9
9
0
0
6tCLCL
2tCLCL
12
12
–
–
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 123 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
0ns
Data Sheet
November 15, 2011
20ns
40ns
60ns
80ns
100ns
120ns
140ns
160ns
CLK0
clk0
68
a19-a0
a19–a0
Address
7
s6/lock_n
s6/lock_n
s6
8
lock_n
s6
15
1
ad15–ad0 (IA186ES),
ad15-ad0/ad7-ad0
ad7–ad0 (IA188ES)
Ptr
12
23
2
ao15–ao8ao15-ao8
(IA188ES)
Address
9
11
ale
ale
10
bhe_n
bhe_n (IA186ES)
4
bhe_n
20
31
inta1_n/inta0_n
inta1_n, inta0_n
22
22
21
den_n
den_n
19
22
dt_r_n
dt/r_n
3
4
s2_n-s0_n
s1_n–s0_n
Figure 19. Interrupt Acknowledge Cycle
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 124 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 84. Interrupt Acknowledge Cycle Timing
No.
Name
Description
General Timing Requirements
1
tDVCL
Data in Setup
2
tCLDX
Data in Hold
General Timing Responses
3
tCHSV
Status Active Delay
4
tCLSH
Status Inactive Delay
ad Address Valid Delay
5
tCLAV
9
tCHLH
ale Active Delay
10 tLHLL
ale Width
11 tCHLL
ale Inactive Delay
19 tDXDL
den_n Inactive to dt/r_n Low
22 tCHCTV
Control Active Delay 2
68 tCHAV
clkouta High to a Address Valid
aIn
Mina
Maxa
10
0
–
–
0
0
0
0
tCLCH-5
0
0
0
0
6
6
12
8
–
8
–
10
8
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 125 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
0ns
A
Data Sheet
November 15, 2011
20ns
40ns
60ns
80ns
100ns
120ns
140ns
160ns
180ns
clkouta
68
a19–a0a
-0
9
1
Invalid Address
5
ad15–ad0 (IA186ES),
ad8–ad0 (IA188ES),
ao15–ao8 (IA188ES)
Invalid Address
9
11
alea
le
10
den_nn
19
dt/r_n
22
n
s1_n–s0_n_
4
Status
3
Figure 20. Software Halt Cycle
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 126 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 85. Software Halt Cycle Timing
No.
Name
Description
General Timing Responses
3
tCHSV
Status Active Delay
4
tCLSH
Status Inactive Delay
7
tCLDV
Data Valid Delay
8
tCHDX
Status Hold Time
9
tCHLH
ale Active Delay
10 tLHLL
ale Width
11 tCHLL
ale Inactive Delay
ad Address Valid to ale Low
12 tAVLL
ad Address Float Delay
15 tCLAZ
16 tCLCSV
mcs_n/pcs_n Inactive Delay
17 tCXCSX
mcs_n/pcs_n Hold from Command Inactive
18 tCHCSX
mcs_n/pcs_n Inactive Delay
19 tDXDL
den_n Inactive to dt/r_n Low
20 tCVCTV
Control Active Delay 1
21 tCVDEX
den_n Inactive Delay
22 tCHCTV
Control Active Delay 2
23 tLHAV
ale High to Address Valid
31 tCVCTX
Control Inactive Delay
68 tCHAV
clkouta High to a Address Valid
aIn
Mina
Maxa
0
0
0
0
0
tCLCH-5
0
tCLCH
0
0
tCLCH
0
0
0
0
0
7.5
0
0
6
6
12
–
8
–
8
–
12
12
–
12
–
10
9
10
–
10
8
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 127 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
0ns
20ns
Data Sheet
November 15, 2011
40ns
60ns
80ns
100ns
120ns
140ns
160ns
180ns
x2x2
36
37
38
x1x1
69
42
43
44
clkoutatA
70
clkoutb
Figure 21. Clock—Active Mode
0ns
20ns
40ns
60ns
80ns
100ns
120ns
140ns
160ns
180ns
x2x2
x1x1
clkouta
clkoutb (CBF=1))
)
0
clkoutb (CBF=0)=
Figure 22. Clock—Power-Save Mode
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 128 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 86. Clock Timing
No.
Name
Description
clkin Requirements
36 tCKIN
x1 Period
37 tCLCK
x1 Low Time
38 tCHCK
x1 High Time
39 tCKHL
x1 Fall Time
40 tCKLH
x1 Rise time
clkout Requirements
42 tCLCL
clkouta Period
43 tCLCH
clkouta Low Time
44 tCHCL
clkouta High Time
45 tCH1CH2
clkouta Rise Time
46 tCL2CL1
clkouta Fall Time
61 tLOCK
Maximum PLL Lock Time
69 tCICOA
x1 to clkouta Skew
70 tCICOB
x1 to clkoutb Skew
aIn
Mina
Maxa
25
7.5
7.5
–
–
66
–
–
5
5
25
tCLCL/2
tCLCL/2
0
0
–
–
–
–
–
–
3
3
0.5
25
35
nanoseconds.
0ns
20ns
40ns
60ns
80ns
100ns
120ns
clkouta
47
srdy
48
Figure 23. srdy—Synchronous Ready
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 129 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
0ns
Data Sheet
November 15, 2011
20ns
40ns
60ns
80ns
100ns
120ns
140ns
tA
u
clkoutao
51
49
ardya
y
rd
50
Sytem Normally not Ready
49
y
rd
ardya
Sytem Normally Ready
50
y
rd
ardya
System Normally Ready
52
Figure 24. ardy—Asynchronous Ready
0ns
20ns
40ns
60ns
80ns
100ns
120ns
140ns
clkouta
53
int4–int0, nmi,
-0
1
tmrin1–tmrin0
54
drq1–drq0
55
tmrout1–tmrout0
Figure 25. Peripherals
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 130 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 87. Ready and Peripheral Timing
No.
Name
Description
Ready and Peripheral Timing Requirements
47 tSRYCL
srdy Transition Setup Time
48 tCLSRY
srdy Transition Hold Time
49 tARYCH
ardy Resolution Transition Setup Time
50 tCLARX
ardy Active Hold Time
51 tARYCHL
ardy Inactive Holding Time
52 tARYLCL
ardy Setup Time
53 tINVCH
Peripheral Setup Time
54 tINVCL
drq Setup Time
Peripheral Timing Responses
55 tCLTMV
Timer Output Delay
aIn
Mina
Maxa
10
3
9
4
6
9
10
10
–
–
–
–
–
–
–
–
0
12
nanoseconds.
0ns
20ns
40ns
60ns
80ns
100ns
120ns
140ns
160ns
x1x1
57
n
_
s
res_nre
57
Low for N x1 Cycles
clkouta
Figure 26. Reset 1
0ns
20ns
40ns
60ns
80ns
100ns
120ns
140ns
160ns
res_nn
clkoutaA
2
rfsh_n/aden_n,
i
z
,u
6
s
e
d
/a
n
s6, uzi_n_
tri-state
ad15–ad0 (IA186ES),
ao15–ao8 (IA188ES),
ad7–ad0 (IA188ES)
tri-state
Figure 27. Reset 2
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 131 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
0ns
Data Sheet
November 15, 2011
20ns
40ns
60ns
80ns
100ns
120ns
140ns
clkouta
clkoutA
58
hold
hold
62
hlda
hlda
15
ad15–ad0 (IA186ES),
den_n
ad[15:0],den_n
63
ad15–ad0 (IA186ES), s6,
rd_n, wr_n,
bhe_n (IA186ES),
s2_n-s1_n,whb_n,wlb_n
dt/r_n, s2_n–s1_n, whb_n,
wlb_n (IA186ES)
Figure 28. Bus Hold Entering
0ns
20ns
40ns
60ns
80ns
100ns
120ns
140ns
clkoutA
clkouta
58
hold
hold
62
hlda
hlda
5
ad15–ad0 (IA186ES),
den_n
ad[15:0],den_n
64
ad15–ad0 (IA186ES), s6,
rd_n, wr_n,
bhe_n (IA186ES),
s2_n-s1_n,whb_n,wlb_n
dt/r_n, s2_n–s1_n, whb_n,
wlb_n (IA186ES)
Figure 29. Bus Hold Leaving
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 132 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 88. Reset and Bus Hold Timing
No.
Name
Description
Reset and Bus Hold Timing Requirements
ad Address Valid Delay
5
tCLAV
ad Address Float Delay
15 tCLAZ
57 tRESIN
res_n Setup Time
58 tHVCL
hld Setup Time
Reset and Bus Hold Timing Responses
62 tCLHAV
hlda Valid Delay
63 tCHCZ
Command Lines Float Delay
64 tCHCV
Command Lines Valid Delay (after Float)
aIn
Mina
Maxa
0
0
10
10
12
12
–
–
0
0
0
7
12
12
nanoseconds.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 133 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
7.
Data Sheet
November 15, 2011
Instruction Set Summary Table
Table 89 summarizes each instruction. A key to abbreviations is presented at the end of the
table.
Table 89. Instruction Set Summary
Instruction
Mnemonic
AAA
AAD
AAM
AAS
ADC
Opcode – Hex
Clock Cycles
Byte 1
37
D5
D4
3F
14
15
80
81
83
Byte 2
–
0A
0A
–
ib
iw
/2 ib
/2 iw
/2 ib
Byte
3–6
–
–
–
–
–
–
–
–
–
10
11
12
13
04
05
80
81
83
00
01
02
03
24
25
80
81
83
/r
/r
/r
/r
ib
iw
/0 ib
/0 iw
/0 ib
/r
/r
/r
/r
ib
iw
/4 ib
/4 iw
/4 ib
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
3/10
3/10
3/10
3/10
3
4
4/16
4/16
4/16
3/10
3/10
3/10
3/10
3
4
4/16
4/16
4/16
3/10
3/14
3/10
3/14
3
4
4/16
4/20
4/20
3/10
3/14
3/10
3/14
3
4
4/16
4/20
4/20
20
21
22
23
62
E8
/r
/r
/r
/r
/r
cw
–
–
–
–
–
–
3/10
3/10
3/10
3/10
33–35
15
3/10
3/14
3/10
3/14
33–35
19
FF
9A
FF
/2
cd
/3
–
–
–
13/19
23
38
17/27
31
54
98
F8
–
–
–
–
2
2
CBW
CLC
Description
ASCII adjust AL after add
ASCII adjust AX before divide
ASCII adjust AL after multiply
ASCII adjust AL after subtract
Add imm8 to AL with carry
Add imm16 to AX with carry
Add imm8 to r/m8 with carry
Add imm16 to r/m16 with carry
Add sign extended imm8 to r/m16
with carry
Add byte reg to r/m8 with carry
Add word reg to r/m16 with carry
Add r/m8 to byte reg with carry
Add r/m16 to word reg with carry
Add imm8 to AL
Add imm16 to AX
Add imm8 to r/m8
Add imm16 to r/m16
Add sign extended imm8 to r/m16
Add byte reg to r/m8
Add word reg to r/m16
Add r/m8 to byte reg
Add r/m16 to word reg
And imm8 with AL
And imm16 with AX
And imm8 with r/m8
And imm16 with r/m16
And sign-extended imm8 with
r/m16
And byte reg with r/m8
And word reg with r/m16
And r/m8 with byte reg
And r/m16 with word reg
Check array index against bounds
Call near, disp relative to next
instruction
Call near, reg indirect mem
Call far to full address given
Call far to address at m16:16
word
Convert byte integer to word
Clear carry flag
CLD
Clear direction flag
FC
–
–
2
2
–
0
–
–
–
–
–
–
CLI
Clear interrupt-enable flag
FA
–
–
2
2
–
–
0
–
–
–
–
–
–
CMC
Complement carry flag
F5
–
–
2
2
–
–
–
–
–
–
–
–
R
ADD
AND
BOUND
CALL
IA186ES
8
15
19
7
3
4
4/16
4/16
4/16
IA188ES
8
15
19
7
3
4
4/16
4/20
4/20
Flags Affected
O
U
U
U
U
R
D
–
–
–
–
–
I
–
–
–
–
–
T
–
–
–
–
–
S
U
R
R
U
R
Z
U
R
R
U
R
A
R
U
U
R
R
P
U
R
R
U
R
C
R
U
U
R
R
R
–
–
–
R
R
R
R
R
0
–
–
–
R
R
U
R
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
2
2
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Refer to the key for abbreviations and an explanation of notation at the end of this table.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 134 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 89. Instruction Set Summary (Continued)
Instruction
Mnemonic
CMP
CMPS
CMPSB
CMPSW
CS
CWD
DAA
DAS
DEC
DIV
DS
ENTER
ES
ESC
HLT
IDIV
Opcode – Hex
Description
Compare imm8 to AL
Compare imm16 to AX
Compare imm8 to r/m8
Compare imm16 to r/m16
Compare sign-extended imm8 to
r/m16
Compare byte reg to r/m8
Compare word reg to r/m16
Compare r/m8 to byte reg
Compare r/m16 to word reg
Compare byte ES:[DI] to byte
segment:[SI]
Compare word ES:[DI] to word
segment:[SI]
Compare byte ES:[DI] to byte
DS:[SI]
Compare word ES:[DI] to word
DS:[SI]
CS segment reg override prefix
Convert word integer to double
word
Decimal adjust AL after addition
Decimal adjust AL after
subtraction
Subtract 1 from r/m8
Subtract 1 from r/m16
Subtract 1 from word reg
Divide unsigned numbers
DS segment override prefix
Create stack frame for nested
procedure
Create stack frame for non-nested
procedure
Create stack frame for nested
procedure
ES segment reg override prefix
Escape - takes a Trap 7
Escape - takes a Trap 7
Escape - takes a Trap 7
Escape - takes a Trap 7
Escape - takes a Trap 7
Escape - takes a Trap 7
Escape - takes a Trap 7
Escape - takes a Trap 7
Suspend instruction execution
Divide Integers
AL = AX/(r/m8);
AH = remainder
Divide Integers
AX = DX:AX/(r/m16);
DX = remainder
Clock Cycles
Byte 1
3C
3D
80
81
83
Byte 2
ib
iw
/7
/7
/7
Byte
3–6
–
–
ib
iw
ib
38
39
3A
3B
A6
/r
/r
/r
/r
–
–
–
–
–
–
3/10
3/10
3/10
3/10
22
3/10
3/14
3/10
3/14
22
A7
–
–
22
26
A6
–
–
22
A7
–
–
2E
99
–
–
27
2F
FE
FF
48+
rw
F6
IA186ES
3
4
3/10
3/10
3/10
IA188ES
3
4
3/10
3/14
3/14
Flags Affected
O
R
D
–
I
–
T
–
S
R
Z
R
A
R
P
R
C
R
R
–
–
–
R
R
R
R
R
22
R
–
–
–
R
R
R
R
R
22
26
R
–
–
–
R
R
R
R
R
–
–
–
4
–
4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
4
4
4
4
?
?
–
–
–
–
–
–
R
R
R
R
R
R
R
R
R
R
/1
/1
–
–
3/15
3/15
3
3/15
3/19
3
R
–
–
–
R
R
R
R
R
–
29/35
29/35
U
–
–
–
U
U
U
U
U
3E
C8
mod
110
r/m
–
iw ib
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
iw 00
–
–
26+20
(n–1)
19
–
–
C8
–
22+16
(n–1)
15
C8
iw 01
–
25
29
26
D8
D9
DA
DB
DC
DD
DE
DF
F4
F6
–
/0
/1
/2
/3
/4
/5
/6
/7
–
/7
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0
–
0
–
–
–
–
–
–
–
–
–
–
–
U
–
–
–
–
–
–
–
U
–
U
–
U
–
U
–
U
/7
–
–
–
–
–
–
–
–
–
–
2
44–52
/
50–58
53–61
/
63–71
–
–
F7
–
–
–
–
–
–
–
–
–
2
44–52
/
50–58
53–61
/
59–67
Refer to the key for abbreviations and an explanation of notation at the end of this table.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 135 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 89. Instruction Set Summary (Continued)
Instruction
Mnemonic
IMUL
IN
INC
INS
INSB
INSW
INT 3
INT
INTO
IRET
Opcode – Hex
Byte 1
F6
Byte 2
/5
Multiply Integers
DX=(r/m16)*AX
F7
/5
–
Multiply Integers
(word reg) = (r/m16)*(sign-ext.
byte integer)
Multiply Integers
(word reg) = (word reg)*(sign-ext.
byte integer)
Multiply Integers
(word reg) = (r/m16)*(sign-ext.
byte integer)
Multiply Integers
(word reg) = (word reg)*(sign-ext.
byte integer)
Input byte from imm port to AL
Input word from imm port to AX
Input byte from port in DX to AL
Input word from port in DX to AX
Increment r/m8 by 1
Increment r/m16 by 1
Increment word reg by 1
Input byte from port in DX to
ES:[DI]
Input word from port in DX to
ES:[DI]
Input byte from port in DX to
ES:[DI]
Input word from port in DX to
ES:[DI]
Generate interrupt 3 (trap to
debug)
Generate type of interrupt
specified by imm8
Generate interrupt 4 if Overflow
Flag (O) is 1
Interrupt return
6B
/r ib
6B
Description
Multiply Integers
AX=(r/m8)*Al
JA
Jump short if above (C & Z = 0)
JNBE
JAE
Jump short if not below or equal
Jump short if above or equal
(C=0)
Jump short if not below (C=0)
Jump short if not carry (C=0)
Jump short if below (C=1)
Jump short if carry (C=1)
Jump short if not above or equal
(C=1)
Jump short if below or equal
(C & Z = 0)
Jump short if not above
(C & Z = 0)
JNB
JNC
JB
JC
JNAE
JBE
JNA
Clock Cycles
Byte
3–6
–
Flags Affected
–
IA186ES
25–28
/
31–34
34–37
/
40–43
22–25
IA188ES
25–28
/
31–34
34–37
/
44–47
22–25
O
R
D
–
I
–
T
–
S
U
Z
U
A
U
P
U
C
R
/r ib
–
22–25
22–25
69
/r iw
–
29–32
29–32
69
/r iw
–
29–32
29–32
E4
E5
EC
ED
FE
FF
40+rw
6C
ib
ib
–
–
/0
/0
–
–
–
–
–
–
–
–
–
–
10
10
8
8
3/15
3/15
3
14
10
14
8
12
3/15
3/19
3
14
–
–
–
–
–
–
–
–
–
R
–
–
–
R
R
R
R
R
–
–
–
–
–
–
–
–
–
CC
–
–
45
45
–
–
0
0
–
–
–
–
–
CD
ib
–
47
47
CE
–
–
48, 4
48, 4
CF
–
–
28
28
77
cb
–
13, 4
13, 4
Restores value of flags reg that was stored on
the stack when the interrupt was taken
–
–
– –
–
–
–
–
–
73
cb
–
13, 4
13, 4
–
–
–
–
–
–
–
–
–
72
cb
–
13, 4
13, 4
–
–
–
–
–
–
–
–
–
76
cb
–
13, 4
13, 4
–
–
–
–
–
–
–
–
–
6D
6C
6D
Refer to the key for abbreviations and an explanation of notation at the end of this table.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 136 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 89. Instruction Set Summary (Continued)
Instruction
Mnemonic
JCXZ
JE
JZ
JG
JNLE
JGE
JNL
JLE
JNG
JMP
JNE
JNZ
JNO
JNP
JPO
JNS
JO
JP
JPE
JS
LAHF
LDS
LEA
LEAVE
LES
LOCK
LODS
LODSB
LODSW
LOOP
LOOPE
LOOPZ
LOOPNE
LOOPNZ
Opcode – Hex
Description
Jump short if CX reg is 0
Jump short if equal (Z=1)
Jump short if 0 (Z=1)
Jump short if greater (Z & S = O)
Jump short if not less or equal
(Z & S = O)
Jump short if greater or equal
(S=O)
Jump short if not less (S = O)
Jump short if less or equal
(Z & S = O)
Jump short if not greater
(Z & S = O)
Jump short direct, disp relative to
next instruction
Jump near direct, disp relative to
next instruction
Jump near indirect
Jump far direct to doubleword
imm address
Jump m16:16 indirect and far
Jump short if not equal (Z=0)
Jump short if not zero (Z=0)
Jump short if not overflow (O=1)
Jump short if not parity (P=0)
Jump short if parity odd (P=0)
Jump short if not sign (S=0)
Jump short if overflow (O=1)
Jump short if parity (P=1)
Jump short if parity (P=1)
Jump short if sign (S=1)
Load AH with low byte of flags reg
Load DS:r16 with segment:offset
from memory
Load offset for m16 word in 16-bit
reg
Destroy procedure stack frame
Load ES:r16 with segment offset
from memory
Asserts lock_n during an
instruction execution
Load byte segment:[SI] in AL
Load word segment:[SI] in AX
Load byte DS:[SI] in AL
Load word DS:[SI] in AX
Decrement count; jump short if
CX 0
Decrement count; jump short if
CX 0 and Z = 1
Decrement count; jump short if
CX 0 and Z = 1
Decrement count; jump short if
CX 0 and Z = 0
Decrement count; jump short if
CX 0 and Z = 0
Clock Cycles
Flags Affected
Byte 1
E3
74
Byte 2
cb
cb
Byte
3–6
–
–
7F
cb
–
13, 4
13, 4
–
–
–
–
–
–
–
–
–
7D
cb
–
13, 4
13, 4
–
–
–
–
–
–
–
–
–
7E
cb
–
13, 4
13, 4
–
–
–
–
–
–
–
–
–
EB
cb
–
14
14
–
–
–
–
–
–
–
–
–
E9
cw
–
14
14
FF
EA
/4
cd
–
–
11/17
14
11/21
14
FF
75
/5
cb
–
–
26
13, 4
34
13, 4
–
–
–
–
–
–
–
–
–
71
7B
cb
cb
–
–
13, 4
13, 4
13, 4
13, 4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
79
70
7A
cb
cb
cb
–
–
–
13, 4
13, 4
13, 4
13, 4
13, 4
13, 4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
78
9F
C5
cb
–
/r
–
–
–
13, 4
2
18
13, 4
2
26
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
8D
/r
–
6
6
–
–
–
–
–
–
–
–
–
C9
C4
–
/r
–
–
8
18
8
26
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
F0
–
–
1
1
–
–
–
–
–
–
–
–
–
AC
AD
AC
AD
E2
–
–
–
–
–
–
–
–
–
–
–
12
16
12
16
16, 6
–
–
12
12
12
12
16, 6
–
–
–
–
–
–
–
–
–
E1
cb
–
E0
cb
–
16, 6
16, 6
–
–
–
–
–
–
–
–
–
IA186ES
15,5
13, 4
IA188ES
15,5
13, 4
O
–
–
D
–
–
I
–
–
T
–
–
S
–
–
Z
–
–
A
–
–
P
–
–
C
–
–
Refer to the key for abbreviations and an explanation of notation at the end of this table.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 137 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 89. Instruction Set Summary (Continued)
Instruction
Mnemonic
MOV
MOVS
MOVSB
MOVSW
MUL
NEG
NOP
NOT
OR
OUT
OUTS
OUTSB
OUTSW
Opcode – Hex
Clock Cycles
Byte 1
88
89
8A
Byte 2
/r
/r
/r
Byte
3–6
–
–
–
8B
8C
8E
A0
A1
/r
/sr
/sr
–
–
–
–
–
–
–
2/9
2/11
2/9
8
8
2/13
2/15
2/13
8
12
A2
A3
–
–
–
–
9
9
9
13
B0+rb
B8+rw
C6
C7
A4
A5
–
–
/0
/0
–
–
–
–
–
–
–
–
3
3
12
12
14
14
3
4
12
13
14
18
A4
A5
F6
–
–
/4
–
–
–
DX::AX = (r/m16) * AX
F7
/4
Perform 2's-complement negation
of r/m8
Perform 2's-complement negation
of r/m16
Perform no operation
Complement each bit in r/m8
Complement each bit in r/m16
OR imm8 with AL
F6
/3
–
14
14
26–28
/
32–34
35–37
/
41–43
3/10
14
18
26–28
/
32–34
35–37
/
45–47
3/10
F7
/3
–
3/10
3/14
90
F6
F7
0C
–
/2
/2
ib
–
–
–
3
3/10
3/10
3
3
3/10
3/14
3
OR imm16 with AX
OR imm8 with r/m8
OR imm16 with r/m16
OR imm8 with r/m16
0D
80
81
83
–
–
–
–
4
4/16
4/16
4/16
4
4/16
4/20
4/20
OR byte reg with r/m8
OR word reg with r/m16
OR r/m8 with byte reg
OR r/m16 with word reg
Output AL to imm port
Output AX to imm port
Output AL to port in DX
Output AX to port in DX
Output byte DS:[SI] to port in DX
Output word DS:[SI] to port in DX
Output byte DS:[SI] to port in DX
Output word DS:[SI] to port in DX
08
09
0A
0B
E6
E7
EE
EF
6E
6F
6E
6F
iw
/1 ib
/1 iw
/1
ib
/r
/r
/r
/r
ib
ib
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
3/10
3/10
3/10
3/10
9
9
7
7
14
3/10
3/14
3/10
3/14
9
13
7
11
14
Description
Copy reg to r/m8
Copy reg to r/m16
Copy r/m8 to reg
Copy r/m16 to reg
Copy segment reg to r/m16
Copy r/m16 to segment reg
Copy byte at segment offset to AL
Copy word at segment offset to
AX
Copy AL to byte at segment offset
Copy AX to word at segment
offset
Copy imm8 to reg
Copy imm16 to reg
Copy imm8 to r/m8
Copy imm16 to r/m16
Copy byte segment [SI] to ES:[DI]
Copy word segment [SI] to
ES:[DI]
Copy byte DS:[SI] to ES:[DI]
Copy word DS:[SI] to ES:[DI]
AX = (r/m8) * AL
IA186ES
2/12
2/12
2/9
IA188ES
2/12
2/16
2/9
Flags Affected
O
–
D
–
I
–
T
–
S
–
Z
–
A
–
P
–
C
–
–
–
–
–
–
–
–
–
–
R
–
–
–
–
–
–
–
R
R
–
–
–
R
R
R
R
R
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0
–
–
–
R
R
U
R
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Refer to the key for abbreviations and an explanation of notation at the end of this table.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 138 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 89. Instruction Set Summary (Continued)
Instruction
Mnemonic
POP
POPA
POPF
PUSH
PUSHA
PUSHF
RCL
RCR
REP
INS
REP
LODS
Opcode – Hex
Description
Pop top word of stack into
memory word
Pop top word of stack into word
reg
Pop top word of stack into DS
Pop top word of stack into ES
Pop top word of stack into SS
Pop DI, SI, BP, BX, DX, CX, & AX
Pop top word of stack into
Processor Status Flags reg
Push memory word onto stack
Push reg word onto stack
Push sign-extended imm8 onto
stack
Push imm16 onto stack
Push CS onto stack
Push SS onto stack
Push DS onto stack
Push ES onto stack
Push AX, CX, DX, BX, original
SP, BP, SI, and DI
Push Processor Status Flags reg
Rotate 9 bits of C and r/m8 left
once
Rotate 9 bits of C and r/m8 left CL
times
Rotate 9 bits of C and r/m8 left
imm8 times
Rotate 17 bits of C and r/m16 left
once
Rotate 17 bits of C and r/m16 left
CL times
Rotate 17 bits of C and r/m16 left
imm8 times
Rotate 9 bits of C and r/m8 right
once
Rotate 9 bits of C and r/m8 right
CL times
Rotate 9 bits of C and r/m8 right
imm8 times
Rotate 17 bits of C and r/m16
right once
Rotate 17 bits of C and r/m16
right CL times
Rotate 17 bits of C and r/m16
right imm8 times
Input CX bytes from port in DX to
ES:[DI]
Input CX bytes from port in DX to
ES:[DI]
Load CX bytes from segment:[SI]
in AL
Load CX words from segment:[SI]
in AX
Clock Cycles
Flags Affected
Byte 1
8F
Byte 2
/0
Byte
3–6
–
58+rw
–
–
10
14
1F
07
17
61
9D
–
–
–
–
–
–
–
–
–
–
8
12
51
8
83
12
Values in word at top of stack are copied into
FLAGS reg bits
FF
50+rw
6A
/6
–
–
–
–
–
16
10
10
20
14
14
–
–
–
–
–
–
–
–
–
68
0E
16
1E
06
60
–
–
–
–
–
–
–
–
–
–
–
–
10
9
9
9
9
36
14
13
13
13
13
68
–
–
–
–
–
–
–
–
–
9C
D0
–
/2
–
–
9
2/15
13
2/15
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
D2
/2
–
C0
/2 ib
–
D1
/2
–
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
D3
/2
–
C1
/2 ib
–
D0
/3
–
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
–
–
–
–
–
–
–
–
–
D2
/3
–
C0
/3 ib
–
D1
/3
–
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
D3
/3
–
75
/3 ib
–
F3
6C
–
5+n/
17+n
5+n/
17+n
8+8n
5+n/
17+n
5+n/
17+n
8+8n
–
–
–
–
–
–
–
–
–
F3
6D
–
8+8n
12+8n
F3
AC
–
6+11n
6+11n
–
–
–
–
–
–
–
–
–
F3
AD
–
6+11n
10+
11n
IA186ES
20
IA188ES
24
O
–
D
–
I
–
T
–
S
–
Z
–
A
–
P
–
C
–
Refer to the key for abbreviations and an explanation of notation at the end of this table.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 139 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 89. Instruction Set Summary (Continued)
Instruction
Mnemonic
REP
MOVS
REP
OUTS
REP
STOS
REPE
CMPS
REPE
SCAS
REPZ
CMPS
REPZ
SCAS
REPNE
CMPS
REPNZ
CMPS
REPNE
SCAS
REPNZ
SCAS
RET
ROL
ROL
Opcode – Hex
Description
Copy CX bytes from
segments:[SI] to ES:[DI]
Copy CX words from
segments:[SI] to ES:[DI]
Output CX bytes from DS:[SI] to
port in DX
Output CX bytes from DS:[SI] to
port in DX
Fill CX bytes at ES:[DI] with AL
Fill CX words at ES:[DI] with AL
Find non-matching bytes in
ES:[DI] and segment:[SI]
Find non-matching words in
ES:[DI] and segment:[SI]
Find non-AL byte starting at
ES:[DI]
Find non-AX word starting at
ES:[DI]
Find non-matching bytes in ES:DI
and segment:[SI]
Find non-matching words in ES:DI
and segment:[SI]
Find non-AL byte starting at ES:DI
Find non-AX word starting at
ES:DI
Find matching bytes in ES:[DI]
and segment:[SI]
Find matching words in ES:[DI]
and segment:[SI]
Find AL byte starting at ES:[DI]
Clock Cycles
Byte 1
F3
Byte 2
A4
Byte
3–6
–
F3
A5
–
8+8n
12+8n
F3
6E
–
8+8n
8+8n
F3
6F
–
8+8n
12+8n
F3
F3
F3
AA
AB
A6
–
–
–
8+8n
8+8n
5+22n
8+8n
12+8n
5+22n
F3
A7
–
5+22n
9+22n
F3
AE
–
5+15n
5+15n
F3
AF
–
5+15n
9+15n
F3
A6
–
5+22n
5+22n
F3
A7
–
5+22n
9+22n
F3
F3
AE
AF
–
–
5+15n
5+15n
5+15n
9+15n
F2
A6
–
5+22n
5+22n
F2
A7
–
5+22n
9+22n
IA186ES
8+8n
IA188ES
8+8n
F2
A6
–
5+22n
5+22n
Find AX word starting at ES:[DI]
F2
A7
–
5+22n
9+22n
Find matching bytes in ES:DI and
segment:[SI]
Find matching words in ES:DI and
segment:[SI]
Find AL byte starting at ES:DI
F2
AE
–
5+15n
5+15n
F2
AF
–
5+15n
9+15n
F2
AE
–
5+15n
5+15n
Find AX word starting at ES:DI
F2
AF
–
5+15n
9+15n
Return near to calling procedure
Return far to calling procedure
C3
CB
20
30
C2
–
data
high
–
16
22
Return near; pop imm16
parameters
Return far; pop imm16
parameters
Rotate 8 bits of r/m8 left once
Rotate 8 bits or r/m8 left CL times
–
data
low
–
18
22
data
high
–
–
25
33
D0
D2
data
low
/0
/0
C0
/0 ib
D1
D3
/0
/0
data
8
–
–
C1
/0 ib
2/15
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
Rotate 8 bits or r/m8 left imm8
times
Rotate 16 bits of r/m8 left once
Rotate 16 bits or r/m8 left CL
times
Rotate 16 bits or r/m8 left imm8
times
CA
data
8
Flags Affected
O
–
D
–
I
–
T
–
S
–
Z
–
A
–
P
–
C
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
U
–
–
–
–
–
–
–
R
U
–
–
–
–
–
–
–
R
Refer to the key for abbreviations and an explanation of notation at the end of this table.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 140 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 89. Instruction Set Summary (Continued)
Instruction
Mnemonic
ROR
SAHF
SAL/SHL
SAR
Opcode – Hex
Description
Rotate 8 bits of r/m8 right once
Rotate 8 bits or r/m8 right CL
times
Rotate 8 bits or r/m8 right imm8
times
Rotate 16 bits of r/m8 right once
Rotate 16 bits or r/m8 right CL
times
Rotate 16 bits or r/m8 right imm8
times
Show AH in low byte of the Status
Flags reg
Multiply r/m8 by 2, once
Clock Cycles
Byte
3–6
–
–
Byte 1
D0
D2
Byte 2
/1
/1
C0
/1 ib
D1
D3
/1
/1
C1
/1 ib
9E
–
data
8
–
data
8
–
–
IA186ES
2/15
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
3
Flags Affected
IA188ES
2/15
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
3
O
U
D
–
I
–
T
–
S
–
Z
–
A
–
P
–
C
R
–
–
–
–
R
R
R
R
R
U
–
–
–
–
R
R
R
R
U
–
–
–
R
R
U
R
R
D0
/4
–
2/15
2/15
Multiply r/m8 by 2, CL times
D2
/4
–
Multiply r/m8 by 2, imm8 times
C0
/4 ib
Multiply r/m16 by 2, once
D1
/4
data
8
–
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
Multiply r/m16 by 2, CL times
D3
/4
–
Multiply r/m16 by 2, imm8 times
C1
/4 ib
Multiply r/m8 by 2, once
D0
/4
data
8
–
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
Multiply r/m8 by 2, CL times
D2
/4
–
Multiply r/m8 by 2, imm8 times
C0
/4 ib
Multiply r/m16 by 2, once
Multiply r/m16 by 2, CL times
D1
D3
/4
/4
data
8
–
–
Multiply r/m16 by 2, imm8 times
C1
/4 ib
Perform a signed division of r/m8
by 2, once
Perform a signed division of r/m8
by 2, CL times
Perform a signed division of r/m8
by 2, imm8 times
Perform a signed division of r/m16
by 2, once
Perform a signed division of r/m16
by 2, Cl times
Perform a signed division of r/m16
by 2, imm8 times
D0
/7
data
8
–
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
D2
/7
–
C0
/7 ib
D1
/7
data
8
–
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
D3
/7
–
C1
/7 ib
data
8
5+n/
17+n
5+n/
17+n
5+n/
17+n
5+n/
17+n
Refer to the key for abbreviations and an explanation of notation at the end of this table.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 141 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 89. Instruction Set Summary (Continued)
Instruction
Mnemonic
SBB
SCAS
SCASB
SCASW
SHR
SS
STC
STD
STI
STOS
STOSB
STOSW
Opcode – Hex
Description
Subtract imm8 from Al with
borrow
Subtract imm16 from AX with
borrow
Subtract imm8 from r/m8 with
borrow
Subtract imm16 from r/m16 with
borrow
Subtract sign-extended imm8
from r/m16 with borrow
Subtract byte reg from r/m8 with
borrow
Subtract word reg from r/m16 with
borrow
Subtract r/m8 from r/m8 with
borrow
Subtract r/m8 reg from byte with
borrow
Compare byte AL to ES:[DI];
update DI
Compare word AL to ES:[DI];
update DI
Compare byte AL to ES:[DI];
update DI
Compare word AL to ES:[DI];
update DI
Divide unsigned of r/m8 by 2,
once
Divide unsigned of r/m8 by 2, CL
times
Divide unsigned of r/m8 by 2,
imm8 times
Divide unsigned of r/m16 by 2,
once
Divide unsigned of r/m16 by 2, CL
times
Divide unsigned of r/m16 by 2,
imm8 times
SS segment reg override prefix
Set the Carry Flag to 1
Set the Direction Flag so the
source Index (SI) and/or the
Destination Index (DI) regs will
decrement during string
instructions
Enable maskable interrupts after
the next instruction
Store AL in byte ES:[DI]; update
DI
Store AX in word ES:[DI]; update
DI
Store AL in byte ES:[DI]; update
DI
Store AX in word ES:[DI]; update
DI
Byte 1
1C
Byte 2
ib
1D
iw
80
18
/3
ib
/3
iw
/3
ib
/r
19
Clock Cycles
Byte
3–6
–
IA186ES
3
IA188ES
3
Flags Affected
O
R
D
–
I
–
T
–
S
R
Z
R
A
R
P
R
C
R
R
–
–
–
R
R
R
R
R
U
–
–
–
R
R
U
R
0
data
8
–
4
4
4/16
4/16
–
4/16
4/20
–
4/16
4/20
3/10
3/10
/r
data
8
–
3/10
3/14
1A
/r
–
3/10
3/10
1B
/r
3/10
3/14
AE
–
data
8
–
15
19
AF
–
–
15
19
AE
–
–
15
19
AF
–
–
15
19
D0
/7
–
2/15
2/15
D2
/7
–
C0
/7 ib
D1
/7
data
8
–
5+n/
17+n
5+n/
17+n
2/15
5+n/
17+n
5+n/
17+n
2/15
D3
/7
–
C1
/7 ib
36
F9
FD
–
–
–
data
8
–
–
–
5+n/
17+n
5+n/
17+n
–
2
2
5+n/
17+n
5+n/
17+n
–
2
2
–
–
–
–
–
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1
–
FB
–
–
2
2
–
–
1
–
–
–
–
–
–
AA
–
–
10
10
–
–
–
–
–
–
–
–
–
AB
–
–
10
14
AA
–
–
10
10
AB
–
–
10
14
81
83
Refer to the key for abbreviations and an explanation of notation at the end of this table.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 142 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 89. Instruction Set Summary (Continued)
Instruction
Mnemonic
SUB
TEST
WAIT
XCHG
Opcode – Hex
Byte 2
ib
2D
iw
–
4
4
80
/5 ib
–
4/16
4/16
Subtract imm16 from r/m16
81
–
4/16
4/20
Subtract sign-extended imm8
from r/m16
Subtract byte reg from r/m8
Subtract word reg from r/m16
Subtract r/m8 from byte reg
Subtract r/m16 from word reg
AND imm8 with AL
AND imm16 with AX
AND imm8 with r/m8
83
/5
iw
/5 ib
–
4/16
4/20
28
29
2A
2B
A8
A9
F6
/r
/r
/r
/r
ib
iw
/0 ib
3/10
3/10
3/10
3/10
3
4
4/10
3/10
3/14
3/10
3/14
3
4
4/10
AND imm16 with r/m16
F7
4/10
4/14
AND byte reg with r/m8
AND word reg with r/m16
84
85
/0
iw
/r
/r
–
–
–
–
–
–
data
8
–
3/10
3/10
3/10
3/14
Performs a NOP
Exchange word reg with AX
Exchange AX with word reg
9B
90
+rw
–
–
–
–
data
8
–
–
–
–
3
3
–
3
3
Exchange byte reg with r/byte
86 /r
–
–
4/17
4/17
–
–
4/17
4/17
–
–
4/17
4/21
–
–
4/17
4/21
Description
Subtract imm8 from AL
Byte 1
2C
Subtract imm16 from AX
Subtract imm8 from r/m8
Exchange r/m8 with byte reg
Exchange word reg with r/m16
87 /r
Exchange r/m16 with word reg
XLAT
XLATB
XOR
Clock Cycles
Byte
3–6
–
IA186ES
3
IA188ES
3
Set AL to memory byte
segment:[BX+unsigned AL]
Set AL to memory byte
DS:[BX+unsigned AL]
XOR imm8 with AL
D7
–
–
11
15
D7
–
–
11
15
34
ib
–
3
3
XOR imm16 with AX
35
iw
–
4
4
XOR imm8 with r/m8
80
/6 ib
–
4/16
4/16
XOR imm16 with r/m16
81
–
4/16
4/20
XOR sign-extended imm8 with
r/m16
XOR byte reg with r/m8
XOR word reg with r/m16
XOR r/m8 with byte reg
XOR r/m16 with word reg
83
/6
iw
/6 ib
–
4/16
4/20
30
31
32
33
/r
/r
/r
/r
–
–
–
–
3/10
3/10
3/10
3/10
3/10
3/14
3/10
3/14
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 143 of 154
Flags Affected
O
R
D
–
I
–
T
–
S
R
Z
R
A
R
P
R
C
R
0
–
–
–
R
R
U
R
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0
–
–
–
R
R
U
R
0
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
7.1
Data Sheet
November 15, 2011
Key to Abbreviations Used in Instruction Set Summary Table
Abbreviations used in the Instruction Set Summary Table are explained below.
7.1.1
Operand Address Byte
The operand address byte is configured as shown below.
7
6
mod field
7.1.2
5 4 3
aux field
2 1 0
r/m field
Modifier Field
The modifier field is defined below.
mod
11
00
01
10
7.1.3
Description
r/m is treated as a register field
DISP = 0, disp-low and disp-high are absent, address displacement is 0
DISP = disp-low sign-extended to 16-bits, disp-high is absent
DISP = disp-high:disp-low
Auxiliary Field
The Auxiliary Field is defined below.
aux
000
001
010
011
100
101
110
111
If mod = 11 and word = 0
AL
CL
DL
BL
AH
CH
DH
BH
Note: When mod
If mod = 11 and word = 1
AX
CX
DX
BX
SP
BP
SI
DI
11, depends on instruction.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 144 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
7.1.4
Data Sheet
November 15, 2011
r/m Field
The r/m field is defined below.
r/m
000
001
010
011
100
101
110
111
Description
EA = (BX) + (SI) + DISP [where EA is the Effective Address]
EA = (BX) + (DI) + DISP
EA = (BP) + (SI) + DISP
EA = (BX) + (DI) + DISP
EA = (SI) + DISP
EA = (DI) + DISP
EA = (BP) + DISP [except if mod = 00, then EA = disp-high:disp-low]
EA = (BX) + DISP
7.1.5
Displacement
The displacement is an 8- or 16-bit value added to the offset portion of the address.
7.1.6
Immediate Bytes
The immediate bytes consist of up to 16 bits of immediate data.
7.1.7
Segment Override Prefix
The segment override prefix is configured as shown below.
7
0
6
0
7.1.8
5
1
4
SR
3
SR
2
1
1
1
0
0
Segment Register
The segment register is shown below.
SR
00
01
10
11
Segment Register
ES
CS
SS
DS
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 145 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
7.2
Data Sheet
November 15, 2011
Explanation of Notation Used in Instruction Set Summary Table
Notation used in the Instruction Set Summary Table is explained below.
Parameter
:
::
Operand
imm8
imm16
m
m8
m16
r/m8
r/m16
7.2.1
Indication
The component of the left is the segment for a component
located in memory. The component on the right is the
offset.
The component of the left is concatenated with the
component on the right.
Definition
Immediate byte: signed number between –128 and 127
Immediate word: signed number between –32768 and 32767
Operand in memory
Byte string in memory pointed to by DS:SI or ES:DI
Word string in memory pointed to by DS:SI or ES:DI
General byte register or a byte in memory
General word register or a word in memory
Opcode
Opcode parameters and definitions are provided below.
Parameter
/0 - /7
/r
/sr
cb
cd
ib
iw
rw
Definition
The Auxiliary Field in the Operand Address byte specifies an extension (from 000 to 111,
i.e., 0 to 7) to the opcode instead of a register. Thus, the opcode for adding (AND) an
immediate byte to a general byte register or a byte in memory is “80 /4 ib.” This indicates
that the second byte of the opcode is “mod 100 r/m.”
The Auxiliary Field in the Operand Address byte specifies a register rather that an opcode
extension. The opcode byte specifies which register, either byte size or word size, is
assigned as in the aux code above.
This byte is placed before the instruction as shown in Section 7.1.7, Segment Override
Prefix.
The byte following the Opcode byte specifies the offset.
The double word following the Opcode byte specifies the offset and is some cases a
segment.
Immediate byte—signed or unsigned determined by the Opcode byte.
Immediate word—signed or unsigned determined by the Opcode byte.
Word register operand as determined by the Opcode byte, aux field.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 146 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
7.2.2
Data Sheet
November 15, 2011
Flags Affected After Instruction
Flags affected after instruction are shown below.
U
R
Undefined
Unchanged
Result dependent
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 147 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
8.
Data Sheet
November 15, 2011
Innovasic/AMD Part Number Cross-Reference Tables
Tables 90 and 91 show Innovasic part numbers cross-referenced with the corresponding AMD
part number.
Table 90. Innovasic/AMD Part Number Cross-Reference for the TQFP
Innovasic Part Number
AMD Part Number
IA186ES-PTQ100I-R-03
AM186ES-20VC\W
lead free (RoHS-compliant) AM186ES-25VC\W
AM186ES-33VC\W
AM186ES-40VC\W
AM186ES-20VI\W
AM186ES-25VI\W
AM186ES-33VI\W
AM186ES-40VI\W
IA188ES-PTQ100I-R-03
AM188ES-20VC\W
lead free (RoHS-compliant) AM188ES-25VC\W
AM188ES-33VC\W
AM188ES-40VC\W
AM188ES-20VI\W
AM188ES-25VI\W
AM188ES-33VI\W
AM188ES-40VI\W
®
Package Type
Temperature Grades
100-Pin Thin Quad Flat
Package (TQFP)
Industrial
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 148 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Table 91. Innovasic/AMD Part Number Cross-Reference for the PQFP
Innovasic Part Number
AMD Part Number
IA186ES-PQF100I-R-03
AM186ES-20KC\W
lead free (RoHS-compliant) AM186ES-25KC\W
AM186ES-33KC\W
AM186ES-40KC\W
AM186ES-20KI\W
AM186ES-25KI\W
AM186ES-33KI\W
AM186ES-40KI\W
IA188ES-PQF100I-R-03
AM188ES-20KC\W
lead free (RoHS-compliant) AM188ES-25KC\W
AM188ES-33KC\W
AM188ES-40KC\W
AM188ES-20KI\W
AM188ES-25KI\W
AM188ES-33KI\W
AM188ES-40KI\W
®
Package Type
Temperature Grade
100-Pin Plastic Quad Flat
Package (PQFP)
Industrial
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 149 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
9.
Data Sheet
November 15, 2011
Errata
The following errata are associated with Version 03 of the IA186ES/IA188ES. A workaround to
the identified problem has been provided where possible.
9.1
Errata Summary
Table 92 presents a summary of errata.
Table 92. Summary of Errata
Errata
No.
9.2
Problem
Ver. 03
1
There is a difference in how priority of timer interrupts are asserted between the
original AMD part and the Innovasic part.
Exists
2
Lock up just after reset is released.
Exists
3
Intermittent startup.
Exists
4
Timer Operation in continuous mode.
Exists
5
DMA interrupt will not bring device out of halt state.
Exists
6
Does not clear the interrupt req bit for INT0 upon entering the ISR.
Exists
7
There is a difference in how hardware handshaking for UARTs during a bus hold
cycle is handled between the original AMD part and the Innovasic part.
Exists
Errata Detail
Errata No. 1
Problem: There is a difference in how priority of timer interrupts are asserted between the
original AMD part and the Innovasic part.
Description: In the original AMD part, timer interrupts cannot be interrupted by another timer
interrupt, even if the new timer interrupt is of a higher priority. The Innovasic part will interrupt
a timer interrupt with a higher-priority timer interrupt. Additionally, if a lower-priority timer
interrupt is interrupted with a higher-priority timer interrupt and another incident of the lowerpriority interrupt occurs during the processing of the higher-priority interrupt, upon execution of
the EOI, a new lower-priority interrupt will be initiated, possibly orphaning the original lowerpriority timer interrupt.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 150 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Workaround: When using nested interrupts, at the beginning of the interrupt routine before the
global interrupts are enabled with a CLI, timer interrupts must be specifically masked. At the
end of the timer interrupt routine being serviced, set the Interrupt Enable Bit in the Process
Status Word to globally disable interrupts prior to clearing the timer interrupt being serviced and
unmask the appropriate timer interrupts.
Errata No. 2
Problem: Lock up just after reset is released.
Description: Usually the first instruction is a long jump to the start of the user’s code. In this
case, the compiler apparently inserted a short jump instruction with zero displacement before the
expected long jump instruction. The OEM device stuttered, but recovered to execute the long
jump, while the device instruction pointer was corrupted, causing the lockup. In summary, a
short jump with zero displacement is a corner case that does not work in the device.
Workaround: Do not use a short jump instruction with zero displacement.
Errata No. 3
Problem: Intermittent startup.
Description: Processor either came out of reset normally, or would go into a series of watchdog
timeouts. The addition of 10K ohm pullups to the wr_n and rd_n outputs seemed to solve the
issue. Further analysis of the OEM device shows the presence of undocumented pullups on these
pins, which will pull them high when the reset condition tristates these pins. The device does not
include internal pullups on these pins allowing these outputs to float during reset.
Workaround: Add 10K ohm pullups to wr_n and rd_n pins to guarantee proper logic levels at
the end of reset.
Errata No. 4
Problem: Timer operation in continuous mode.
Description: The timers (Timer0 and Timer1) do not function per the specification when set in
continuous mode with no external timer input stimulus to initiate/continue count.
Workaround: None.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 151 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
Data Sheet
November 15, 2011
Errata No. 5
Problem: DMA interrupt will not bring device out of halt state.
Description: When device is in halt state, the interrupt caused by a DMA completion will not
bring the CPU out of the halt state.
Workaround: Use idle mode instead of halt.
Errata No. 6
Problem: Does not clear the interrupt req bit for INT0 upon entering the ISR.
Description: The interrupt bit for INT0 is not cleared until the interrupt routine is complete.
Workaround: Do not rely on the bit to be cleared when nesting interrupts.
Errata No. 7
Problem: How hardware handshaking for UARTs during a bus hold cycle is handled differently
between the AMD part and the Innovasic part.
Description: In the AMD part, hardware handshaking works per the data sheet. The Innovasic
part will occasionally drive a handshake signal to the incorrect state during bus hold instead of
tristating the pin.
Workaround: None. Avoid using hardware handshaking in conjunction with the bus hold
operation with the Innovasic part UARTs.
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 152 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
10.
Data Sheet
November 15, 2011
Revision History
Table 93 presents the sequence of revisions to document IA211050902.
Table 93. Revision History
Date
Revision
Description
Page(s)
August 17, 2007
11
Edition released.
NA
January 31, 2008
12
Errata 6 and 7 added.
136
February 19, 2008
13
Errata 7 clarified.
136
August 7, 2008
14
Column 2 of Peripheral Control Registers
table changed from “Serial Port 0” to “Serial
Port 1” in 6 bottom rows.
9
December 24, 2008
15
Document reformatted and elements added
to meet publication standards. Improved
figures and tables. Added Conventions,
Acronyms and Abbreviations, and Summary
of Errata table.
All
January 25, 2010
16
Corrected PQFP Package Dimensions table.
30
February 25, 2011
17
Updated section 2.2.50 to clarify that power
rating is +10%; Removed packaging options
to support the elimination of SnPb lead
plating options.
44, 148, 149
July 22, 2011
18
Corrected pin names for various pins.
17-29
November 15, 2011
19
Corrected pin names for pins 42, 43
29
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 153 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184
IA186ES/IA188ES
8-Bit/16-Bit Microcontrollers
11.
Data Sheet
November 15, 2011
For Additional Information
The IA186ES/IA188ES is a form, fit, and function replacement for the original AMD
Am186ES/188ES family of microcontrollers. Innovasic produces replacement ICs using its
MILES system cloning technology that produces replacement ICs far more complex than
“emulation” while ensuring they are compatible with the original IC. MILES captures the design
of a clone so it can be produced even as silicon technology advances. MILES also verifies the
clone against the original IC so that even the “undocumented features” are duplicated.
The IA186ES/IA188ES family of microcontrollers replaces obsolete AMD Am186ES/188ES
devices, allowing customers to retain existing board designs, software compilers/assemblers, and
emulation tools and thus avoid expensive redesign efforts.
The Innovasic Support Team wants its information to be complete, accurate, useful, and easy to
understand. Please feel free to contact experts at Innovasic with suggestions, comments, or
questions at any time.
Innovasic Support Team
3737 Princeton NE
Suite 130
Albuquerque, NM 87107
Phone: +1 505-883-5263
Fax: +1 505-883-5477
Toll Free: (888) 824-4184
Website: http://www.innovasic.com
®
IA211050902-19
UNCONTROLLED WHEN PRINTED OR COPIED
Page 154 of 154
http://www.innovasic.com
Customer Support:
1-888-824-4184