AWT6309 HELP2TM AWS/KPCS CDMA 3.4V/28dBm Linear Power Amplifier Module Data Sheet - Rev 2.4 FEATURES • InGaP HBT Technology • High Efficiency: 40 % @ +28 dBm output 22 % @ +17 dBm output • Low Quiescent Current: 15 mA • Low Leakage Current in Shutdown Mode: <1 µA • Internal Voltage Regulation • Optimized for a 50 Ω System • Low Profile Miniature Surface Mount Package: 1 mm • CDMA 1XRTT, 1xEV-DO Compliant • Pinout Enables Easy Phone Board Migration From 4 mm x 4 mm Package M9 Package 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module • RoHS-Compliant Package, 250 oC MSL-3 APPLICATIONS • CDMA/EVDO AWS/KPCS band Wireless Handsets and Data Devices PRODUCT DESCRIPTION The AWT6309 meets the increasing demands for higher efficiency and smaller footprint in CDMA 1X handsets. The package pinout was chosen to enable handset manufacturers to switch from a 4 mm x 4 mm PA module with few layout changes while reducing board area requirements by 44%. The AWT6309 uses ANADIGICS’ exclusive InGaP-Plus™ technology, which combines HBT and pHEMT devices on the same die, to enable state-of-the-art reliability, temperature stability, and ruggedness. The AWT6309 is part of ANADIGICS’ High-Efficiency-at-Low-Power (HELP™) family of CDMA power amplifiers, which deliver low quiescent currents and significantly greater efficiency without a costly external DAC or DC-DC converter. Through selectable bias modes, the AWT6309 achieves optimal efficiency across different output power levels, specifically at low- and midrange power levels where the PA typically operates, thereby dramatically increasing handset talk-time and standby-time. Its built-in voltage regulator eliminates the need for external voltage regulation components. The 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 Ω system. 05/2009 Figure 1: Block Diagram AWT6309 Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VBATT Battery Voltage 2 RFIN RF Input 3 VMODE Mode Control Voltage 4 VEN 5 GND Ground 6 GND Ground 7 RFOUT RF Output 8 VCC PA Enable Voltage Supply Voltage Data Sheet - Rev 2.4 05/2009 AWT6309 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC and VBATT) 0 +5 V Mode Control Voltage (VMODE) 0 +3.5 V Enable Voltage (VEN) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Operating Frequency (f) 1710 - 1780 MHz Supply Voltage (VCC and VBATT) +3.2 +3.4 +4.2 V Enable Voltage (VEN) +2.2 0 +2.4 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +2.2 0 +2.4 - +3.1 +0.5 V Low Bias Mode High Bias Mode +28.0 - dBm - +85 °C RF Output Power (POUT) 27.5 Case Temperature (TC) -30 (1) COMMENTS The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at Vcc = +3.2 V, Pout is derated by 0.5 dB. Data Sheet - Rev 2.4 05/2009 3 AWT6309 Table 4: Electrical Specifications - CDMA Operation (TC = +25 OC, VBATT = VCC = +3.4 V, VEN = +2.4 V, 50 V system, IS-95 uplink waveform) PARAMETER MIN TYP MAX Gain 25 12.5 12.5 27.5 14.5 14.5 30 17 17 dB Adjacent Channel Power at +1.25 MHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz - -50 -53 -52 -46.5 -46.5 -46.5 dBc Adjacent Channel Power at + 1.98 MHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz - -56 -56 -53 -53 dBc POUT = +28 dBm, VMODE = 0 V POUT = +17 dBm, VMODE = +2.4 V Adjacent Channel Power at +2.25 MHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz - -61 -61 -57 -57 dBc POUT = +28 dBm, VMODE = 0 V POUT = +17 dBm, VMODE = +2.4 V Power-Added Efficiency 36 17 40 22 - % POUT = +28 dBm, VMODE = 0 V POUT = +17 dBm, VMODE = +2.4 V Quiescent Current (Icq) - 15 18 mA through VCC pin, VMODE = +2.4 V Enable Current - 0.3 0.6 mA through VEN pin, PA "on" Mode Control Current - 0.3 0.6 mA through VMODE pin, VMODE = +2.4 V Battery Current - 2.5 5 mA through VBATT pin, VMODE = +2.4 V Leakage Current - <1 5 µA VCC = +4.2 V, VEN = 0 V, VMODE = 0 V Noise in Receive Band - -134 -136 -136 -132 -134 -134 Harmonics 2fo 3fo, 4fo - -40 -55 -30 -30 dBc Input Impedance - - 2.3:1 VSWR Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure UNIT COMMENTS POUT = +28 dBm, VMODE = 0 V POUT = +17 dBm, VMODE = +2.4 V POUT = +18 dBm, VMODE = +2.4 V, VCC = +3.7 V POUT = +28 dBm, VMODE = 0 V POUT = +17 dBm, VMODE = +2.4 V POUT = +18 dBm, VMODE = +2.4 V, VCC = +3.7 V 1840 MHz to 1870 MHz dBm/Hz 2110 MHz to 2155 MHz 1574 MHz to 1577 MHz - - -65 dBc POUT < +28 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating ranges 8:1 - - VSWR Applies over full operating range Notes: 1. ACPRs and Efficiency Limits apply at 1745 MHz (IS-95 modulation). Data Sheet - Rev 2.4 4 05/2009 AWT6309 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to both the VEN and VMODE voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications. Table 5: Bias Control POUT LEVELS LOGIC VEN VMODE CDMA - low power <+17 dBm Low +2.4 V +2.4 V CDMA - high power >+17 dBm High +2.4 V 0V - Shutdown 0V 0V APPLICATION Shutdown Figure 3: Application Circuit Data Sheet - Rev 2.4 05/2009 5 AWT6309 PACKAGE OUTLINE Figure 4: M9 Package Outline - 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module 091 091 CC Figure 5: Branding Specification 6 Data Sheet - Rev 2.4 05/2009 = KR-for-KOREA AWT6309 COMPONENT PACKAGING Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 3 mm x 3 mm x 1 mm 12 mm 4 mm 2500 7" Data Sheet - Rev 2.4 05/2009 7 AWT6309 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION AWT6309RM9Q7 -30 °C to +85 °C RoHS-Compliant 8 Pin 3 mm x 3 mm x 1 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module AWT6309RM9P9 -30 °C to +85 °C RoHS-Compliant 8 Pin 3 mm x 3 mm x 1 mm Partial Tape and Reel Surface Mount Module COMPONENT PACKAGING ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 Data Sheet - Rev 2.4 05/2009