DATA SHEET CPS CTX CSD ANT_SEL SKY65378-11: 860 to 930 MHz RF Front-End Module Applications Smart meters In-home appliances Smart thermostats TX_IN Logic Control ANT1 TX_FLT Features TR Small QFN (24-pin, 4 x 4 mm) package (MSL1, 260 C per JEDEC J-STD-020) Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. ANT2 RX_FLT LNA LNA_IN Integrated LNA with programmable gain Integrated antenna switching with transmit/receive diversity function Low FEM noise figure: 2.5 dB typical Fast turn-on/turn-off time: <1 μs 2.0 to 4.8 V supply operation Sleep mode current: <1 μA Y1093 Figure 1. SKY65378-11 Block Diagram Description The SKY65378-11 is a high-performance, highly integrated frontend module (FEM) designed for low power ISM band applications operating in the 860 to 930 MHz band. The device is designed for ease of use and maximum flexibility, with fully matched 50 Ω input and output, and digital controls compatible with 1.6 to 3.6 V CMOS levels. The RF blocks operate over a wide supply voltage range from 2.0 to 4.8 V, which allows the SKY65378-11 to be used in battery powered applications over a wide spectrum of the battery discharge curve. The device is provided in a 4 x 4 mm, 24-pin Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202510D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2015 1 N/C VCC N/C N/C N/C N/C DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE 24 23 22 21 20 19 17 N/C CPS 3 16 TX_IN CTX 4 15 N/C TX_FLT 5 14 ANT1 TR 6 13 N/C 7 8 9 10 11 12 ANT2 2 RX_FLT N/C N/C N/C LNA_IN 18 GND 1 ANT_SEL CSD S3212 Figure 2. SKY65378-11 Pinout – 24-Pin QFN (Top View) Table 1. SKY65378-11 Signal Descriptions Pin Name Description Pin Name Description 1 CSD Shutdown control pin 13 N/C Not connected internally 2 N/C Not connected internally 14 ANT1 Antenna port 1 3 CPS Receive path select control input 15 N/C Not connected internally 4 CTX Transmit enable control input 16 TX_IN Transmit signal to antennas (from external) 5 TX_FLT Transmit signal from TR port 17 N/C Not connected internally 6 TR Common receive/transmit port 18 N/C Not connected internally 7 ANT_SEL Antenna select control input 19 N/C Not connected internally 8 GND Ground 20 N/C Not connected internally 9 LNA_IN LNA input (from receive filter) 21 N/C Not connected internally 10 N/C Not connected internally 22 N/C Not connected internally 11 RX_FLT Receive signal from antennas (to receive filter) 23 VCC Positive power supply 12 ANT2 Antenna port 2 24 N/C Not connected internally Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 July 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202510E DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE Electrical and Mechanical Specifications The state of the SKY65378-11 is determined by the logic provided in Table 9. Table 10 provides the logic for the two antenna ports. The absolute maximum ratings of the SKY65378-11 are provided in Table 2. The recommended operating conditions are specified in Table 3. Electrical specifications are provided in Tables 4 to 8. Table 2. SKY65378-11 Absolute Maximum Ratings (Note 1) Parameter Symbol Supply voltage (no RF) VCC Minimum Maximum Units –0.3 5.5 V Transmit input power at TX_IN port PIN_TX_MAX +32 dBm Transmit input power at TR port (Note 2) PIN_TR_MAX +20 dBm Receive input power at ANT1 or ANT2 ports PIN_RX_MAX +10 dBm Voltage Standing Wave Ratio VSWR 10:1 – Operating temperature TA –40 +85 C Storage temperature TSTG –40 +125 C Electrostatic discharge: ESD 1000 1000 50 V V V Charged Device Model (CDM), Class 4 Human Body Model (HBM), Class 1C Machine Model (MM), Class A Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. Note 2: PIN_TR_MAX = +12 dBm at worst case where VSWR = 10:1. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. SKY65378-11 Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units Supply voltage VCC 2.0 4.0 4.8 V Operating temperature TA –40 +25 +85 C Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202510E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2015 3 DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE Table 4. SKY65378-11 Electrical Specifications: DC Characteristics (Note 1) (VCC = 4 V, TA = +25 C as Measured on Evaluation Board [Not De-Embedded to Device], Unless Otherwise Noted) Parameter Total supply current Symbol ICQ_TX Transmit mode ICQ_RX_LOWGAIN Receive low gain mode ICQ_RX_HIGHGAIN Sleep supply current Test Condition ICC_OFF Min Receive high gain mode Typical Max 330 μA 4 mA 8 Sleep mode Units 0.3 mA 1.00 μA Note 1: Performance is guaranteed only under the conditions listed in this table. Table 5. SKY65378-11 Electrical Specifications: Transmit Characteristics (Note 1) (VCC = 4 V, TA = +25 C as Measured on Evaluation Board [Not De-Embedded to Device], All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Frequency Symbol Test Condition f Min Typical 860 Max Units 930 MHz Insertion loss S21 TR to ANT1 and ANT2 1.5 dB Input return loss S11 Measured at TR –10 dB Output return loss S22 Measured at ANT1 and ANT2 –10 dB Turn-on time tON From 50% of CTX edge to 90% of final RF output power 1 μs From 50% of CTX edge to 10% of final RF output power 1 μs Turn-off time (Note 2) tOFF Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: CSD must remain high for 500 ns after CTX is set low. Table 6. SKY65378-11 Electrical Specifications: Receive Characteristics (1 of 2) (Note 1) (VCC = 4 V, TA = +25 C as Measured on Evaluation Board [Not De-Embedded to Device], All Unused Ports Terminated with 50 Ω, Input Port ANT1 or ANT2, Output Port TR, 0 Ω Connected Between the RX_FLT and LNA_IN Pins in Lieu of External Filters, Unless Otherwise Noted) Parameter Symbol Frequency f Receive low gain mode RXLG Receive high gain mode RXHG Test Condition Min Typical 860 Max Units 930 MHz @ 900 to 930 MHz and 860 to 870 MHz, CSD = logic “1,” CPS = CTX = logic “0” 14 dB @ 900 to 930 MHz and 860 to 870 MHz, CPS = CSD = logic “1,” CTX = logic “0” 17 dB Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 July 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202510E DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE Table 6. SKY65378-11 Electrical Specifications: Receive Characteristics (2 of 2) (Note 1) (VCC = 4 V, TA = +25 C as Measured on Evaluation Board [Not De-Embedded to Device], All Unused Ports Terminated with 50 Ω, Input Port ANT1 or ANT2, Output Port TR, 0 Ω Connected Between the RX_FLT and LNA_IN Pins in Lieu of External Filters, Unless Otherwise Noted) Typical Max Units Receive noise figure, low-gain mode Parameter NFLG @ 900 to 930 MHz and 860 to 870 MHz, CSD = logic “1,” CPS = CTX = logic “0” 2.7 3.5 dB Receive noise figure, high-gain mode NFHG @ 900 to 930 MHz and 860 to 870 MHz, CPS = CSD = logic “1,” CTX = logic “0” 2.5 3 dB 1 dB input compression point, low-gain mode IP1dBLG @ 900 to 930 MHz and 860 to 870 MHz, CSD = logic “1,” CPS = CTX = logic “0” –10 dBm –12 dBm @ 900 to 930 MHz and 860 to 870 MHz, into 50 Ω, ANT1 and ANT2 ports –12 dB –12 dB 1 dB input compression point, high-gain mode Antenna port return loss Symbol IP1dBHG S11ANT1,2 Test Condition @ 900 to 930 MHz and 860 to 870 MHz, CPS = CSD = logic “1,” CTX = logic “0” Min –15 TR port return loss in receive mode S22TR @ 900 to 930 MHz and 860 to 870 MHz, into 50 Ω Turn-on time tON From 50% of CTX edge to 90% of final RF output power 1 μs Turn-off time tOFF From 50% of CTX edge to 10% of final RF output power 1 μs Note 1: Performance is guaranteed only under the conditions listed in this table. Table 7. SKY65378-11 Electrical Specifications: Diversity Antenna Characteristics (Note 1) (VCC = 4 V, TA = +25 C, f = 900 to 930 MHz and 860 to 870 MHz, as Measured on Evaluation Board [De-Embedded to Device], All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Isolation between ANT1 and ANT2 ports ISOANTSW Isolation between TX_IN and TR ports Insertion loss from TX_IN to ANT1 Test Condition Min Typical Max Units 30 dB ISORXTX 20 dB TX_ANT1 0.9 dB Insertion loss from TX_IN to ANT2 TX_ANT2 0.9 dB Insertion loss from ANT1 to RX_FILT RX_ANT1 0.9 dB Insertion loss from ANT2 to RX_FILT RX_ANT2 0.9 dB Antenna 1 to antenna 2 switching time, transmit mode tANT1/ANT2_TX 940 ns Antenna 1 to antenna 2 switching time, receive mode tANT1/ANT2_RX 800 ns Note 1: Performance is guaranteed only under the conditions listed in this table. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202510E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2015 5 DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE Table 8. SKY65378-11 Electrical Specifications: Logic Characteristics (Note 1) (TA = +25 C as Measured on Evaluation Board [De-Embedded to Device], Unless Otherwise Noted) Parameter Symbol Voltage logic input: High Low Test Condition VIH VIL Min 1.6 0 Typical Max Units Vcc (Note 2) 0.3 V V Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: For ANT_SEL, the maximum voltage is 3.6 V. Table 9. SKY65378-11 Mode Logic Truth Table (Note 1) CPS (Pin 3) CSD (Pin 1) CTX (Pin 4) Sleep (all off) 0 0 0 Receive low gain 0 1 0 Receive high gain 1 1 0 Transmit X 1 1 Shutdown (Note 2) 0 0 1 Shutdown (Note 2) 1 0 0 Shutdown (Note 2) 1 0 1 Mode Note 1: See Table 8 for logic voltage levels. “X” = don’t care Note 2: Expect approximately 15 μA through each control pin that has logic high. For true sleep mode, set CPS, CSD, and CTX low. Table 10. SKY65378-11 Antenna Port Logic Truth Table CPS (Pin 3) CSD (Pin 1) CTX (Pin 4) ANT_SEL (Pin 7) ANT1 port enabled X X X 0 ANT2 port enabled X X X 1 Mode Note 1: See Table 8 for logic voltage levels. “X” = don’t care Evaluation Board Description The SKY65378-11 Evaluation Board is used to test the performance of the SKY65378-11 FEM. An Evaluation Board schematic diagram is shown in Figure 3. Table 11 provides the Bill of Materials (BOM) list for Evaluation Board components. A photograph of the Evaluation Board is shown in Figure 4. Transmit Performance. The 860 MHz to 930 MHz (depending on the region) amplifier performance is monitored by applying an RF signal to J5 (TX_IN) and measuring the output power on J2 (ANT2) or J3 (ANT1). Evaluation Board Setup Procedure If use of the TR port is desired, the RF signal first enters connector J1 (TR), exits connector J6 (TX_FLT) through an external PA and filter – or is directly shorted to connector J5 (TX_IN) – then passed to either J2 (ANT2) or J3 (ANT1). 1. Connect J1, J2, and J3 to 50 Ω instruments. If applicable, terminate all unused ports with 50 Ω. Receive Performance. The 860 MHz to 930 MHz LNA performance is monitored by applying an RF signal to J2 (ANT2) or J3 (ANT1) and measuring the output signal on J1 (TR). 2. Connect the supply ground to pin 1 of the J4 header. 3. Connect 3.6 V to pin 3 or 4 of the J4 header. Refer to Tables 9 and 10 for path selection logic. CAUTION: Care should be taken not to overdrive the device by applying too much RF on the input. A suitable starting input power is –20 dBm. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 July 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202510E DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE J4 VDD C6 4.7 μF C1 10 nF CTX CPS L3 0Ω CSD C2 22 pF ANT_SEL × × N/C 20 CSD N/C N/C N/C TX_IN CPS 4 J6 CTX N/C CTX 5 ANT1 7 8 9 10 11 ANT2 RX_FLT Transmit/Receive N/C TR GND ANT_SEL 6 LNA_IN TX_FLT J1 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 N/C 18 17 × × J5 16 15 × L8 6.8 nH 14 13 L6 6.8 nH Transmit from Ext to Ant J3 Antenna Port 1 C12 3.3 pF × 12 L9 6.8 nH × ANT_SEL VCC VDD × 3 Transmit 3 6 19 2 CPS 1 4 N/C × 21 N/C 22 VCC N/C 1 CSD × 23 N/C × 24 2 L7 6.8 nH J2 Antenna Port 2 R2 0Ω C13 3.3 pF Note: Some component labels may be different from the corresponding component symbol shown here. Component values, however, are accurate as of the date of this data sheet. S3213 Figure 3. SKY65378-11 Evaluation Board Schematic Diagram Table 11. SKY65378-11 Evaluation Board Bill of Materials Component Value Size Manufacturer Mfr Part Number Description C1 10 nF 0402 Murata GRM155R71E103KA01 Multilayer ceramic capacitor C2 22 pF 0402 Murata GRM1555C1H220JZ01 Multilayer ceramic capacitor C6 4.7 μF 0603 Murata GRM188R60J475KE19 Multilayer ceramic capacitor C12, C13 3.3 pF 0402 Murata GRM1555C1H3R3CZ01 Multilayer ceramic capacitor J1, J2, J3, J5, J6 SMA End launch Johnson Components 142-0701-851 SMA end launch straight jack receptacle, tab contact J4 10x2 100 mil Samtec TSW-110-07-G-D 100 mil header L3 0Ω 0402 Panasonic ERJ2GE0R00 Thick film chip resistor L6, L7, L8, L9 6.8 nH 0603 Murata LQG18HN6N8S00D High frequency multilayer inductor R2 0Ω 0402 Panasonic ERJ2GEJ0R0 Thick film chip resistor Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202510E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2015 7 DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE Figure 4. SKY65378-11 Evaluation Board Package Dimensions Package and Handling Information The PCB layout footprint for the SKY65378-11 is shown in Figure 5. Typical part markings are noted in Figure 6. Package dimensions for the 24-pin QFN are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY65378-11 is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 July 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202510E 5X 1.02 5X 0.51 0 5X 0.51 5X 1.02 DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE 4.40 2.70 4.40 2.70 1 18 2 17 3 16 4 15 5 14 6 13 18 5X 1.02 17 5X 0.51 0 0 15 5X 0.51 5X 1.02 13 0.60 Typ. 7 8 9 10 11 12 8 Board Metal 4.50 2.50 25X ∅0.254 Via Pattern (Note 1) 4.40 1.00 Typ. 4.50 2.50 23 10 0.500 Typ. 0.25 Typ. 24 0 22 21 20 19 24 1 18 2 17 3 16 4 23 22 0.20 Typ. 21 20 19 1 18 2 17 3 16 15 4 15 5 14 5 14 6 13 6 13 1.00 Typ. 0.20 Typ. 0.70 Typ. 4.40 0.60 Typ. 7 8 0.35 Typ. 9 10 11 12 0.500 Typ. Component Outline Solder Mask Pattern (Note 2) 7 8 0.25 Typ. 9 10 11 12 0.500 Typ. 64% solder coverage on center pad Stencil Pattern (Note 3) NOTES: 1. Via hole recommendations: 0.025 mm Cu via wall plating (minimum), soldermask on the far side should tent or plug via holes. 2. Soldermask recommendations: Contact board fabricator for recommended soldermask offset and tolerance. 3. Stencil recommendations: 0.125 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer better paste release. Dimension and tolerancing according to ASME Y14.5M-1994. Unless specified, dimensions are symmetrical about center lines. All dimensions are in millimeters. S3214 Figure 5. SKY65378-11 PCB Layout Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202510E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2015 9 DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE Skyworks Part Number Lot Code Date Code: YY = Calendar Year WW = Week CC = Country Code Y2169 Figure 6. Typical Part Marking 0.850 ± 0.050 2X 4.000 ± 0.050 0.15 C B See Note 3 24 23 22 21 20 2.700 ± 0.050 0.10 M C A B A 0.203 Ref. 19 19 20 21 22 23 24 0.30 x 45° 0.10 M C A B 4.000 ± 0.050 1 1 18 18 2 17 17 3 16 16 3 4 15 15 4 5 14 14 5 6 13 13 6 R0.05 Typ. 2 2.700 ± 0.050 0.500 Seating Plane 2X 0.15 C 7 8 9 10 11 12 12 0–0.05 C Top View 11 10 9 24X 0.250 ± 0.050 0.10 M C A B 0.05 M C Side View 8 24X 0.400 ± 0.050 Bottom View NOTES: 1. All measurements are in millimeters. 2. Dimensioning and tolerancing according to ASME Y14.5M-1994. Unless otherwise specified the following values apply: Decimal Tolerance: Angular Tolerance: X.X (1 place) ± 0.1 mm ±1° X.XX (2 places) ± 0.05 mm X.XXX (3 places) ± 0.025 mm 3. Terminal #1 identification mark located within marked area. 4. Unless specified, dimensions are symmetrical about center lines. Figure 7. SKY65378-11 24-Pin QFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 7 July 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202510E S3210 DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE 8.0 ± 0.1 12.0 ± 0.3 1.22 ± 0.1 2.0 ± 0.05 ø1.5 ± 0.1 4.0 (Note 1) 0.254 ± 0.013 1.75 ± 0.1 5.5 ± 0.05 4.35 ± 0.1 4.35 ± 0.1 Pin1 Location Notes: 1. 10 sprocket hole pitch cumulative tolerance ±0.2. 2. Camber in compliance with EIA-481. 3. All measurements are in millimeters. S3211 Figure 8. SKY65378-11 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202510E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 9, 2015 11 DATA SHEET • SKY65378-11: 860 TO 930 MHz RF FRONT-END MODULE Ordering Information Model Name SKY65378-11: RF FEM Manufacturing Part Number SKY65378-11 Evaluation Board Part Numbers SKY65378-11-EK1 Copyright © 2012-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 July 9, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202510E