CH100 Transistor Optocoupler

PART NUMBER
CH100 Series
COMPONENT
ISSUE 1
SPECIFICATION
May 2014
Component Specification
Transistor Optocouplers
With Very Low Operating Temperatures
M1077 IECQ
1077/M
Further copies of this document may be obtained from:
ISOCOM LIMITED
WASHINGTON, UK
NE38 0AH
www.isocom.uk.com
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 1 of 11
Transistor Optocouplers
Very Low Operating Temperatures
■ CH100/101/102/103
■ CH100/101/102/103/L2
■ CH100/101/102/103/L2S
Features
Applications
▪ Released to European Standard and
Complies to Mil Std
▪ Space Radiation Equipment
▪ Military, high reliability system
▪ Total Ionizing Dose Tested to 150KRad(si)
▪ Medical instruments
▪ Displacement Damage to 1 MEV x 10¹²
▪ Suitable for Hybrid packaging
▪ Low Temperature Operation upto -150°C
▪ Mos, Cmos Applications
▪ 4 Pad LCC Package
▪ Data Transmission
▪ Flexibility in Design for mounting styles
▪ Power Supply
▪ High Current Transfer Ratio
▪ Logic Interfacing
 High Isolation Voltage upto 1000vdc
 Hermetically Sealed
Description
The CH100 has been designed and manufactured to meet the requirements of very low temperatures experienced
in harsh environments encounted by space applications. These devices can be wire bonded within a hybrid
application or mounted directly onto a PCB board offering the customer flexibility in their design.
They are single channel, hermetically sealed, Radiation Hard optically coupled isolators. Each channel is
composed of a infra-red emitting diode and a silicon phototransistor. The CH100 series was manufactured to meet
the JANS standard in conjunction with MIL-PRF-19500 procedures (please see next page for all other applicable
specifications). Package styles for this device include 4 Pad LCC.
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 2 of 11
Standards
The following specifications have been complied with in the manufacturing of this product to JANS MIL-STD
requirements:
Military Compliance Specifications
MIL-PRF-19500 – General Specification for Discrete Semiconductor Devices
IECQ – M1077
Military Compliance Standards
MIL-STD-202 – Test Method Standard Electronic and Electrical Component Parts
MIL-STD-883 – Test Method Standard Microcircuits
MIL-STD-750 – Test Methods for Semiconductor Devices
ISO 9001:2008 – Manufacturing of Optocouplers and Optoelectronic components.
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 3 of 11
Selection Guide Package Styles and Configuration Options
Package
Lead Style
Channels
Common Channel Wiring
Isocom Part Number and Options
Commercial
Defense Screen Level
Space Screen Level
Standard Gold Plate Finish
Solder Dipped
4 pad LCC
1
CH100/101/102/103
CH100/101/102/103/L2
CH100/101/102/103/L2S
Gold Plate
Option 20
Functional Diagrams
Device Marking
CH100
CH101
4 pad LCC
1 Channel
4 pad LCC
1 Channel
CH102
CH103
4 pad LCC
1 Channel
4 pad LCC
1 Channel
ISOCOM
XXXXXXX
XXXX
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 4 of 11
Manufacturer
Isocom Part Number
Date Code (XX year XX week)
Outline Drawings
Absolute Maximum Ratings
TA = 25°C U.O.S.
Storage Temperature
Operating Temperature
Lead Soldering Temperature
Input-to-Output Isolation Voltage
-65°C to +150°C
-150°C to +125°C
260°C 1.6mm from case for 10S
1000VDC
Input Diode
Forward DC Current
40mA
Reverse DC Voltage
Peak forward Current
Power Dissipation
2V
1.0mA
60mW
DC at (or below) +65°C Derates linearly to +125°C free
air temperature at the rate of 0.67mA/°C.
Pw1µS, PRR<300pps  10µS ms
Derates linearly above 65°C at 1.0W/°C
Output Transistor
Collector-Emitter Voltage
Emitter-Collector Voltage
Collector Current
Power Dissipation
70V
7V
50mA
300mW
BVCEO
BVECO
Derates linearly above 25°C at 3.0W/°C
Coupled Device
Input to Output Isolation Voltage
Power Dissipation
SolderingTemperature,Soldering Iron
1000V
360mW
260,5
SolderingTemperature,Vapour Phase
220,40
ESD Classification
Class 2
°C,s This part shall not be re-soldered until 3 minutes
have elapsed.
°C,s This part shall not be re-soldered until 3 minutes
have elapsed.
Class 2 with minimum critical path voltage of 4,000 to
15,999V. MIL-STD-883
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 5 of 11
Electrical Characteristics
Input Diode Electrical Characteristics TA = 25°C U.O.S.
Parameter
Forward Voltage
Symbol
VF
Reverse Current
IR
Test Conditions
IF = 10mA
IF = 10mA -55°C
IF = 10mA +125°C
VR = 2.0V
Min
1.3
1.3
1.1
-
Type
-
Max
1.8
1.8
1.8
100
Units
V
V
V
µA
70
100
-
V
7
9
-
V
-
7
10
100
100
150
µA
µA
µA
100
150
-
-
0.3
%
%
V
500
-
105
7
1000
20.0
Vdc
Ω
µS
-
7
20.0
µS
-
-
5.0
µS
-
-
5.0
µS
Output Detector Electrical Characteristics
Collector-Emitter
Breakdown Voltage
Emitter-Collector
Breakdown Voltage
Collector–Emitter Leakage
Current
V(BR)CEO
V(BR)ECO
ICEO
IC = 1mA
IE = 0.1mA
VCE = 20v, IF = 0
VCE = 20v IF = 0, -55°C
VCE = 20v, IF = 0, +125°C
Coupled Electrical Characteristics
DC Current Transfer Ratio
IC/IF
Collector-Emitter Saturation
Voltage
Isolation Voltage
Input to Output Resistance
Rise Time
VCE
(Sat)
V in-out
R in-out
tr
Fall Time
tf
Propagation Delay
H-L
tPHL
Propagation Delay
L-H
tPLH
IF = 1.0mA, VCE = 5V
IF = 10.0mA, VCE = 5V (Note 1)
IC =10.0mA
IF = 20mA
T = 5s (Note 2)
VIO = 500V (Note 2)
RL = 100Ohms
Vcc = 10V
IF = 10mA
RL = 100Ohms
Vcc = 10V
IF = 10mA
RL = 100Ohms
Vcc = 10V
IF = 10mA
RL = 100Ohms
Vcc = 10V
IF = 10mA
Notes:
1)
Sample and hold pulse shall not be longer than 0.1 seconds. Duty cycle shall be 10.
2)
Measurements with inputs shorted together and outputs shorted together.
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 6 of 11
Electrical Measurements During and on Completion of Radiation Testing
Parameter
Input
Diode
Forward
Voltage
Input
Diode
Reverse
Current
Photo Transistor CollectorEmitter Dark Current
Coupled Current Transfer
Ratio
Collector-Emitter Saturation
Voltage
Symbol
VF
Test Conditions
IF = 10mA
Min
1.3
Max
1.8
Units
V
IR
VR = 2.0V
-
100
µA
ICEO
VCE = 20v, IF = 0
-
100
µA
IC
IF = 1.0mA, VCE = 5V
IF = 10.0mA, VCE = 5V (note 1)
IC =10.0mA
IF = 20mA
100
150
-
0.3
%
%
V
VCE
(Sat)
NOTE 1 = Sample and hold pulse shall be not longer than 0.1 seconds. Duty cycle shall be 10
NOTE 2 = Please note that if you require any parameters to be controlled to meet your design needs such as CTR,
VF, ICEO, VCE(SAT), please contact Isocom Limited customer service team. We also offer a selection of
screening procedures that will match your needs.
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 7 of 11
GROUP TESTING TO MIL-STD 750
GROUP
Group A
SG1
SG2
SG3
SG4
Group B
SG 1
SG 2
SG 3
TEST
MIL-STD-750
Visual inspection & mechanical
dimensions
DC static test at 25°C
DC static test at 125°C and ‐55°C
Dynamic test at 25°C
Method 2071
Physical dimensions
Solderability
Resistance to solvents
Thermal Shock
Electrical measurement
Bond strength
Acc. steady‐state operation life
Method 2066
Method 2026
Method 1022
Method 1056 Cond. B, 25
cycles
Method 1051, 100 cycles,
-55/+125°C
Method 1071, Cond. H
(fine), Cond. C (gross)
pre and post
2075
Method 2037, Cond. D
Method 2017
Method 1037, 1042, Cond
D, Tab.5-5
Method 1071, Cond. H
(fine), Cond. C (gross)
pre and post
Method 2037, Cond. D
Method 1027
Electrical measurement
Bond strength
pre and post
Method 2037, Cond. D
Thermal Shock
Method 1056, Cond. B, 25
shocks
Method 1051, Cond. C,
‐55/+125°C , 25 cycles
(total 45 cycles including
screening)
Method 1071, Cond. H
(fine), Cond. C (gross)
Method 1021
pre and post
Method 2016,
non‐operating, 1500 G, 0.5
ms, 5 blows in each
orientation (X1,Y1,Z1)
Method 2056
Method 2006, at a peak
level of 5000 G
pre and post
Temperature cycling
Hermetic seal fine and gross leak
SG 4
Electrical measurement
Decap internal visual inspection
Bond strength
Die shear
Intermittent operation life
Hermetic seal fine and gross leak
SG 5
Group C
SG 2
Temperature cycling
Hermetic seal fine and gross leak
SG 3
Moisture resistance
Electrical measurement
Mechanical shock
Vibration
Constant acceleration
SG 6
Electrical measurement
Steady state operating life Not required
as B5 is available on same lot
yes
yes
yes
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 8 of 11
READ AND
RECORD
yes
yes
yes
yes
yes
yes
yes
yes
yes
100% SCREENING TO MIL-STD 750 TEST
MIL-STD-750
Internal Visual
2072
READ AND RECORD?
Sealing
(Fine Leak)
(Gross Leak)
Temp Cycling
Const. Acceler
PIND
Radiography
Initial Electrical
HTRB
Interim Electrical
Burn-In
Final Electrical
PDA
(Fine Leak)
(Gross Leak)
1071, Condition H1
1071, Condition C
1051, Condition
B‐55/+125°C, 20 Cycles.
2006, 5000G, Y1 only.
2052, Condition A
2076
125°C, ‐55°C, 25°C
1039
25°C only
1039
125°C, ‐55°C, 25°C
Max. 5%, pre/post B1
electrical and delta at RT
only
1071, Condition H1
1071, Condition C
R&R
R&R
R&R
Calculate & R
Solder Dip
Fine Leak
Gross Leak
1071, Condition H1
1071, Condition C
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 9 of 11
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 10 of 11
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 11 of 11
Similar pages