Quick Start Guide.pdf

CY5676A PROCTM BLE 256KB MODULE
CY5676A PRoCTM BLE 256KB Module is a complete solution to add BLE connectivity
to any embedded system with Bluetooth® 4.2 features. The module features a
PRoC BLE device (CYBL11573-56LQXI), 24-MHz and 32.768-kHz crystals, a PCB
antenna, and other passives while providing access to all GPIOs of the device.
For more information on Cypress’s BLE solutions visit www.cypress.com/BLE
PRoC BLE is a single-chip solution with a 48-MHz ARM® Cortex®-M0 CPU,
Bluetooth 4.2 radio, CapSense® technology for touch-sensing, two serial
communication blocks (SCBs), a 12-bit ADC, four Timer/Counter/PWMs, four
additional PWMs, I2S for digital audio, and segment LCD direct-drive capability.
Antenna matching
network (AMN)
Wiggle antenna
Ctank
Cmod
24-MHz crystal
P0_1
P0_3
P0_5
P1_0
P1_2
P0_6
P0_7
XRES
GND
VDDD
GND
P3_6
P3_4
P3_2
P3_0
P4_0
P4_1
P2_6
P2_4
P2_2
P2_0
VDDR
P0_0
P0_2
P0_4
VREF
P1_1
P1_4
P1_3
P1_5
P1_7
P1_6
CYBL11573-56LQXI
PRoC BLE device
VDD
GND
P1_5
P1_4
SAR bypass capacitor
(bottom side)
VDDA
P3_7
P3_5
P3_3
P3_1
P5_1
P5_0
P2_7
P2_5
P2_3
P2_1
GND
32.768-kHz crystal
(bottom side)
4-pin UART header
Fig-1: Pinout Description for CY5676A
Note: To apply power to the module, apply 1.9 V - 5.0 V to any of the VDD pins (VDD,
VDDD, VDDA, or VDDR) and 0 V to any GND pin
CY5676A PROCTM BLE 256KB MODULE
STANDALONE USE WITH PSOC CREATORTM IDE AND CY8CKIT-002 MINIPROG3
Step 1: Select the 5-pin connector setting in PSoC Creator or PSoC Programmer.
Step 2: Use 0.1” male headers (not included) or jumper wires to connect the
MiniProg3 to the module.
Pin Mapping
CY8CKIT-002
CY5676A
VTARG
GND
VDDD
GND
RES
XRES
SCLK
P0_7
SDAT
P0_6
Fig-2: Programming and Debugging with CY8CKIT-002 MiniProg3
USING THE PROC BLE MODULE WITH THE CY8CKIT-042-BLE PIONEER KIT
Step 1: Plug the module on the CY8CKIT-042-BLE Pioneer Kit Baseboard.
Step 2: Create your design in PSoC Creator IDE and use the BLE Pioneer Kit to
program and debug.
Fig-3: Programming and Debugging with CY8CKIT-042-BLE Pioneer Baseboard
The CY5676A module is intended for development purposes only. Users are advised
to test and evaluate this module in an RF development environment. This module is
not a finished product and when assembled may not be resold or otherwise
marketed unless all required authorizations are first obtained.
Contact [email protected] for details.
For more information about this kit, visit www.cypress.com/CY5676A
© 2015 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the
properties of their respective owners. 001-97334 Rev.*B