CY8CKIT-143A PSOC® 4 BLE 256KB MODULE CY8CKIT-143A PSoC® 4 BLE 256KB Module is an easy-to-use solution for creating a complete BLE system with Bluetooth® 4.2 features. The module features a PSoC 4 BLE device (CY8C4248LQI-BL583), 24-MHz and 32.768-kHz crystals, a PCB antenna, and other passives while providing access to all GPIOs of the device. For more information on Cypress’s BLE solutions visit www.cypress.com/BLE PSoC 4 BLE is a 48-MHz ARM® Cortex®-M0 based single-chip solution that integrates a programmable analog front end, programmable digital peripherals, CapSense® touch-sensing technology, and includes a royalty-free stack and radio compatible with Bluetooth 4.2. Antenna matching network (AMN) Wiggle antenna Ctank Cmod 24-MHz crystal P0_1 P0_3 P0_5 P1_0 P1_2 P0_6 P0_7 XRES GND VDDD P0_0 P0_2 P0_4 VREF P1_1 P1_4 P1_3 P1_5 P1_7 P1_6 GND P3_6 P3_4 P3_2 P3_0 P4_0 P4_1 P2_6 P2_4 P2_2 P2_0 VDDR CY8C4248LQI-BL583 PSoC 4 BLE device VDD GND P1_5 P1_4 SAR bypass capacitor (bottom side) VDDA P3_7 P3_5 P3_3 P3_1 P5_1 P5_0 P2_7 P2_5 P2_3 P2_1 GND 32.768-kHz crystal (bottom side) 4-pin UART header Fig-1: Pinout Description for CY8CKIT-143A Note: To apply power to the module, apply 1.9 V - 5.0 V to any of the VDD pins (VDD, VDDD, VDDA, or VDDR) and 0 V to any GND pin CY8CKIT-143A PSOC® 4 BLE 256KB MODULE STANDALONE USE WITH PSOC CREATORTM IDE AND CY8CKIT-002 MINIPROG3 Step 1: Select the 5-pin connector setting in PSoC Creator or PSoC Programmer. Step 2: Use 0.1” male headers (not included) or jumper wires to connect the MiniProg3 to the module. Pin Mapping CY8CKIT-002 CY8CKIT-143A VTARG GND VDDD GND RES XRES SCLK P0_7 SDAT P0_6 Fig-2: Programming and Debugging with CY8CKIT-002 MiniProg3 USING THE CY8CKIT-143A MODULE WITH CY8CKIT-042-BLE PIONEER KIT Step 1: Plug the module on the CY8CKIT-042-BLE Pioneer Kit Baseboard. Step 2: Create your design in PSoC Creator IDE and use the BLE Pioneer Kit to program and debug. Fig-3: Programming and Debugging with CY8CKIT-042-BLE Pioneer Baseboard The CY8CKIT-143A module is intended for development purposes only. Users are advised to test and evaluate this module in an RF development environment. This module is not a finished product and when assembled may not be resold or otherwise marketed unless all required authorizations are first obtained. Contact [email protected] for details. For more information about this kit, visit www.cypress.com/CY8CKIT-143A © 2015 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the properties of their respective owners. 001-97333 Rev.*B