CY8CKIT-042-BLE QUICK START GUIDE BLUETOOTH ® LOW ENERGY PIONEER KIT 1 CY5671 PRoCTM BLE Module 2 BLE Pioneer Baseboard preloaded with CY8CKIT-142 PSoC® 4 BLE Module 8 1 TM 4 Four jumper wires (4 inches each) 5 Two proximity sensor wires (5 inches each) 2 6 Coin cell (3-V CR2032) 3 4 3 CY5670 CySmart USB Dongle 5 7 7 USB Standard-A to Mini-B cable 6 8 Quick Start Guide (this document) 1 • Connect the dongle to your computer's USB port. This demo does not require installing the drivers for Windows 8 or earlier versions. Refer to Kit Guide for Windows 8.1 or later 3 • Press the button SW2 on both the dongle and the baseboard. The red LED on the baseboard and the blue LED on the dongle will stay on for three seconds before turning off, indicating a Bluetooth low energy connection between the two boards 2 • Insert the 3-V coin cell (included with the kit) into the coin cell holder on the rear side of the baseboard 4 • Move your finger over the CapSense® slider on the baseboard to control the brightness of the blue LED on the dongle CY8CKIT-042-BLE QUICK START GUIDE 5 • Download and install the PSoC Creator IDE, BLE Pioneer Kit example projects, documents, and hardware design files from www.cypress.com/CY8CKIT-042-BLE TM 6 • To debug your PSoC Creator project, connect the baseboard (with the PSoC 4 BLE or PRoC BLE module) to your computer with a USB cable • Refer to Chapter 4 of the Kit User Guide for additional information on example projects Note: If evaluating this demo near another BLE Pioneer Kit that is advertising (when using the default out-of-box firmware), the dongle may connect to the other baseboard instead. In this case, press the reset button (SW1) on both the dongle and baseboard of your kit, then repeat step 3 to retry connection between the two Feature List and Pinout Description for CySmart USB Dongle CY8C5868LTI-LP039 PSoC 5LP programmer and debugger PRoC BLE external programming header User LED User button 32.768-kHz crystal (bottom side) P1_4 (PRoC BLE) P1_5 (PRoC BLE Status LED Wiggle antenna USB plug Antenna matching network (AMN) Power LED 24-MHz crystal PRoC BLE reset button CYBL10162-56LQXI PRoC BLE device PSoC 5LP programming test points CY8CKIT-042-BLE QUICK START GUIDE Feature List and Pinout Description for PSoC 4 BLE Module PSoC 4 BLE - A single chip solution with a 48-MHz ARM® Cortex®-M0, BLE radio, CapSense, programmable analog (12-bit ADC, 2 current DACs, 2 low-power comparators, 4 low-power opamps) and programmable digital (4 Timer/Counter/PWMs, 4 Universal Digital Blocks, 2 Serial Communication Blocks) Antenna matching network (AMN) Ctank Cmod Wiggle antenna 24-MHz crystal PSoC 4 BLE module header (J2) PSoC 4 BLE module header (J1) SAR bypass capacitor (bottom side) P0_1 P0_0 GND VDDA P0_3 P0_2 P3_6 P3_7 P0_5 P0_4 P3_4 P3_5 P1_0 VREF P3_2 P3_3 P1_2 P1_1 P3_0 P3_1 P0_6 P1_4 P4_0 P5_1 P0_7 P1_3 P4_1 P5_0 XRES P1_5 P2_6 P2_7 GND P1_7 P2_4 P2_5 VDDD P1_6 P2_2 P2_3 P2_0 P2_1 32.768-kHz crystal (bottom side) P1_4 P1_5 VDD 4-pin UART header GND CY8C4247LQI-BL483 PSoC 4 BLE device VDDR GND Feature List and Pinout Description for PRoC BLE Module PRoC BLE - A single chip solution with a 48-MHz ARM Cortex-M0, BLE radio, CapSense, 2 Serial Communication Blocks, 12-bit ADC, 4 Timer/Counter/PWMs, 4 additional PWMs, I2S and LCD CYBL10563-56LQXI PRoC BLE device P3_6 P3_7 P0_5 P0_4 P3_4 P3_5 P1_0 VREF P3_2 P3_3 P1_2 P1_1 P3_0 P3_1 P0_6 P1_4 P4_0 P5_1 P0_7 P1_3 P4_1 P5_0 XRES P1_5 P2_6 P2_7 GND P1_7 P2_4 P2_5 VDDD P1_6 P2_2 P2_3 P2_0 P2_1 32.768 kHz crystal (bottom side) 4-pin UART header VDDR GND P1_4 SAR bypass capacitor (bottom side) PRoC BLE module header (J1) GND VDDA P0_3 P0_2 P1_5 PRoC BLE module header (J2) P0_1 P0_0 VDD 24-MHz crystal Antenna matching network (AMN) Ctank Cmod GND Wiggle antenna CY8CKIT-042-BLE QUICK START GUIDE BLUETOOTH ® LOW ENERGY PIONEER KIT Feature List and Pinout Description for BLE Pioneer Baseboard 15 6 16 17 1 RGB LED 2 BLE device reset button 14 1 3 CapSense proximity header 13 2 4 User button 5 CapSense slider 3 6 Arduino compatible I/O Headers (J2/J3/J4) 4 7 Arduino-compatible power header (J1) 8 Digilent® PmodTM compatible I/O header (J5) 9 Cypress F-RAM 1 Mb (FM24V10-G) 12 11 10 5 8 7 6 10 PSoC 5LP I/O header (J8) P3_5/SCL P3_4/SDA VREF/AREF GND/GND P0_3/D13 P0_1/D12 P0_0/D11 P0_2/D10 P0_4/D9 P0_5/D8 P1_0/D7 P1_1/D6 P1_2/D5 P1_3/D4 P1_7/D3 P1_6/D2 P1_5/D1 P1_4/D0 9 11 PSoC 5LP programmer and debugger (CY8C5868LTI-LP039) 12 Coin cell holder (bottom side) 13 USB connector (J13) 14 Power LED and Status LED P2_0 P5LP1_2 VDD P5LP0_0 P5LP3_4 P5LP3_6 P5LP12_6 P5LP12_1 P5LP12_0 P5LP2_5 15 System power supply jumper (J16) - LDO 1.9 V~5 V 16 BLE power supply jumper / current measurement (J15) P2_5 P2_4 P2_3 P2_2 P2_1 P2_0 A0/P3_0 A1/P3_1 A2/P3_2 A3/P3_3 A4/P3_4 A5/P3_5 NC IOREF/BLE_VDD RESET/RESET 3.3 V/V 3.3 5 V/V 5.0 GND/GND GND/GND Vin/VIN GND P5LP12_5 P5LP3_0 P5LP12_7 P5LP3_7 P5LP3_5 P5LP0_1 17 BLE module headers (J10/J11) ArduinoTM Pin Definition BLE Pioneer Baseboard For the latest information about this kit and to download kit software and hardware files, visit www.cypress.com/CY8CKIT-042-BLE © 2014 - 2015 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the properties of their respective owners. Doc.#: 001-92251 Rev.*I