EZ-BLE™ PROC™ EVALUATION BOARD CYBLE-012011-EVAL The EZ-BLE™ PRoC™ Evaluation Board (CYBLE-012011-EVAL) enables you to evaluate and develop applications on the EZ-BLE PRoC Modules (CYBLE-012011-00 and CYBLE-012012-10). The EZ-BLE PRoC Module is a fully-integrated, fully-certified, 14.5 mm x 19.2 mm x 2.0 mm, programmable, Bluetooth® Smart module designed to reduce your time-to-market. For more information, visit: www.cypress.com/EZ-BLEModule - EZ-BLE Module home page www.cypress.com/EZ-BLEEval - EZ-BLE PRoC Evaluation Board kit page www.cypress.com/go/AN96841 - Getting started guide EZ-BLE PROC Module J5 Header J2 Header (Bottom side) NC NC NC NC NC NC P1_0 VREF NC NC P0_6 P1_4 P0_7 NC XRES P1_5 GND P1_7 VDD P1_6 J6 Header VDD VDDR J3 Header Cmod GND VDD P3_6 P3_7 P3_4 P3_5 P3_2 P3_3 NC NC P4_0 P5_1 NC P5_0 P2_6 P3_5 P2_4 P0_4 P2_2 P2_3 P2_0 P0_5 VDDR GND J1 Header (Bottom side) J4 MiniProg3 10-pin Programming Header Fig 1: CYBLE-012011-EVAL Pinout Description Note: To use the CYBLE-012011-EVAL board, you must separately purchase either the CY8CKIT-002 MINIPROG3 or the CY8CKIT-042-BLE BLE PIONEER KIT. EZ-BLETM PROCTM EVALUATION BOARD 1: Connect the CYBLE-012011-EVAL to the CY8CKIT-002 (MiniProg3) Connect a jumper on the J3 header Connect the MiniProg3 to the J4 10-pin header J3 Fig 2: J3 Header Fig 3: Programming/Debugging with MiniProg3 OR Plug the CYBLE-012011-EVAL on the CY8CKIT-042-BLE baseboard. Note: Jumper on CYBLE-012011-EVAL’s J3 header can be connected or disconnected. Fig 4: Programming and debugging with CY8CKIT-042-BLE BLE Pioneer Kit Baseboard Pin Mapping between CY8CKIT-042-BLE (Base) and CYBLE-012011-EVAL (Eval) (Base) (Eval) (Base) (Eval) (Base) (Eval) (Base) (Eval) GND GND P1_4 P1_4 P2_4 P2_4 P3_6 P3_6 VDDD, VDDDA VDD P1_5 P1_5 P2_5 P0_4 P3_7 P3_7 VDDR VDDR P1_6 P2_6 P2_6 P4_0 P4_0 XRES XRES P1_6 P1_7 P1_7 P2_7 P3_5 P5_0 P5_0 VREF VREF P2_0 P2_0 P3_2 P3_2 P5_1 P5_1 P0_6 P0_6 P2_1 P0_5 P3_3 P3_3 P0_7 P0_7 P2_2 P2_2 P3_4 P3_4 P1_0 P1_0 P2_3 P2_3 P3_5 P3_5 2: Create a project using the CYBLE-012011-00/CYBLE-012012-10 MPN and program /debug using PSoC® CreatorTM 3.3 SP1 The EZ-BLE PRoC Module (CYBLE-012011-00) is qualified for the Bluetooth 4.1 specification and is certified for the 2.4 GHz unlicensed frequency range in USA (FCC), Canada (IC) and Europe (CE). Visit www.cypress.com/go/support for technical support. © 2015 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the properties of their respective owners. 002-10100 Rev.**