AD AD9865BCPRL

Broadband Modem Mixed-Signal Front End
AD9865
FUNCTIONAL BLOCK DIAGRAM
AD9865
PWR DWN
MODE
TXEN/SYNC
TXCLK
2-4X
IAMP
TxDAC
0 TO –7.5dB
IOUT_G+
IOUT_N+
IOUT_N–
IOUT_G–
0 TO –12dB
10
CLKOUT_1
CLKOUT_2
CLK
SYN.
ADIO[9:4]/
Tx[5:0]
2M CLK
MULTIPLIER
OSCIN
XTAL
ADIO[3:0]/
Rx[5:0]
10
RXE/SYNC
RXCLK
AGC[5:0]
2-POLE
LPF
1-POLE
LPF
RX–
6
4
REGISTER
CONTROL
0 TO 6dB
∆ = 1dB
– 6 TO 18dB –6 TO 24dB
∆ = 6dB
∆ = 6dB
04493-0-001
SPI
RX+
ADC
80MSPS
APPLICATIONS
Powerline networking
VDSL and HPNA
IOUT_P–
Low cost 3.3 V CMOS MxFETM for broadband modems
10-bit D/A converter
2×/4× interpolation filter
200 MSPS DAC update rate
Integrated 23 dBm line driver with 19.5 dB gain control
10-bit, 80 MSPS A/D converter
−12 dB to +48 dB low noise RxPGA (< 3.0 nV/rtHz)
Third order, programmable low-pass filter
Flexible digital data path interface
Half- and full-duplex operation
Backward-compatible with AD9975 and AD9875
Various power-down/reduction modes
Internal clock multiplier (PLL)
2 auxiliary programmable clock outputs
Available in 64-lead chip scale package or bare die
IOUT_P+
FEATURES
Figure 1.
GENERAL DESCRIPTION
The AD9865 is a mixed-signal front end (MxFE) IC for
transceiver applications requiring Tx and Rx path functionality
with data rates up to 80 MSPS. Its flexible digital interface,
power saving modes, and high Tx-to-Rx isolation make it well
suited for half- and full-duplex applications. The digital interface is extremely flexible allowing simple interfaces to digital
back ends that support half- or full-duplex data transfers, thus
often allowing the AD9865 to replace discrete ADC and DAC
solutions. Power saving modes include the ability to reduce
power consumption of individual functional blocks, or to power
down unused blocks in half-duplex applications. A serial port
interface (SPI®) allows software programming of the various
functional blocks. An on-chip PLL clock multiplier and
synthesizer provide all the required internal clocks, as well as
two external clocks from a single crystal or clock source.
or to an internal low distortion current amplifier. The current
amplifier (IAMP) can be configured as a current- or voltagemode line driver (with two external npn transistors) capable of
delivering in excess of 23 dBm peak signal power. Tx power can
be digitally controlled over a 19.5 dB range in 0.5 dB steps.
The Tx signal path consists of a bypassable 2×/4× low-pass
interpolation filter, a 10-bit TxDAC, and a line driver. The
transmit path signal bandwidth can be as high as 34 MHz at an
input data rate of 80 MSPS. The TxDAC provides differential
current outputs that can be steered directly to an external load
The AD9865 provides a highly integrated solution for many
broadband modems. It is available in a space saving 64-pin chip
scale package and is specified over the commercial (−40°C to
+85°C) temperature range.
The receive path consists of a programmable amplifier
(RxPGA), a tunable low-pass filter (LPF), and a 10-bit ADC.
The low noise RxPGA has a programmable gain range of
−12 dB to +48 dB in 1 dB steps. Its input referred noise is less
than 3 nV/rtHz for gain settings beyond 36 dB. The receive path
LPF cutoff frequency can be set over a 15 MHz to 35 MHz
range or simply bypassed. The 10-bit ADC achieves excellent
dynamic performance over a 5 MSPS to 80 MSPS span. Both
the RxPGA and the ADC offer scalable power consumption
allowing power/performance optimization.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2004 Analog Devices, Inc. All rights reserved.
AD9865
TABLE OF CONTENTS
Specifications..................................................................................... 3
TxDAC and IAMP Architecture .............................................. 28
Tx Path Specifications.................................................................. 3
Tx Programmable Gain Control .............................................. 30
Rx Path Specifications.................................................................. 4
TxDAC Output Operation........................................................ 30
Power Supply Specifications ....................................................... 5
IAMP Current-Mode Operation.............................................. 30
Digital Specifications ................................................................... 6
IAMP Voltage-Mode Operation .............................................. 31
Serial Port Timing Specifications............................................... 7
IAMP Current Consumption Considerations........................ 32
Half-Duplex Data Interface (ADIO Port) Timing
Specifications ................................................................................ 7
Receive Path .................................................................................... 33
Full-Duplex Data Interface (Tx and Rx Port) Timing
Specifications ................................................................................ 8
Explanation of Test Levels........................................................... 8
Absolute Maximum Ratings............................................................ 9
Thermal Characteristics .............................................................. 9
ESD Caution.................................................................................. 9
Pin Configuration and Function Descriptions........................... 10
Typical Performance Characteristics ........................................... 12
Rx Path Typical Performance Characteristics ........................ 12
TxDAC Path Typical Performance Characteristics ............... 16
IAMP Path Typical Performance Characteristics .................. 18
Serial Port ........................................................................................ 19
Register Map Description ......................................................... 21
Serial Port Interface (SPI) ......................................................... 21
Digital Interface .............................................................................. 23
Half-Duplex Mode ..................................................................... 23
Full-Duplex Mode ...................................................................... 24
RxPGA Control .......................................................................... 25
TxPGA Control .......................................................................... 27
Transmit Path .................................................................................. 28
Rx Programmable Gain Amplifier........................................... 33
Low-Pass Filter ........................................................................... 34
Analog-to-Digital Converter (ADC)....................................... 35
AGC Timing Considerations.................................................... 36
Clock Synthesizer ........................................................................... 37
Power Control and Dissipation .................................................... 39
Power-Down ............................................................................... 39
Half-Duplex Power Savings ...................................................... 39
Power Reduction Options......................................................... 40
Power Dissipation ...................................................................... 42
Mode Select upon Power-Up and Reset.................................. 42
Analog and Digital Loop-Back Test Modes............................ 43
PCB Design Considerations.......................................................... 44
Component Placement.............................................................. 44
Power Planes and Decoupling .................................................. 44
Ground Planes ............................................................................ 44
Signal Routing ............................................................................ 44
Evaluation Board ............................................................................ 46
Outline Dimensions ....................................................................... 47
Ordering Guide .......................................................................... 47
Digital Interpolation Filters ...................................................... 28
REVISION HISTORY
11/04—Data Sheet Changed from Rev. 0 to Rev. A
Changes to Specifications Tables .................................................... 3
Changes to Serial Table .................................................................. 19
Changes to Full Duplex Mode section......................................... 24
Change to TxDAC and IAMP Architecture section .................. 29
Change to TxDAC Output Operation section............................ 30
Insert equation................................................................................ 37
Change to Figure 84 caption ......................................................... 42
11/03—Revision 0: Initial Version
Rev. A | Page 2 of 48
AD9865
SPECIFICATIONS
Tx PATH SPECIFICATIONS
AVDD = 3.3 V ± 5%, DVDD = CLKVDD = DRVDD = 3.3 V ± 10%; fOSCIN = 50 MHz, fDAC = 200 MHz, RSET = 2.0 kΩ, unless otherwise
noted.
Table 1.
Parameter
TxDAC DC CHARACTERISTICS
Resolution
Update Rate
Full-Scale Output Current (IOUTP_FS)
Gain Error1
Offset Error
Voltage Compliance Range
TxDAC GAIN CONTROL CHARACTERISTICS
Minimum Gain
Maximum Gain
Gain Step Size
Gain Step Accuracy
Gain Range Error
TxDAC AC CHARACTERISTICS2
Fundamental
Signal-to-Noise and Distortion (SINAD)
Signal-to-Noise Ratio (SNR)
Total Harmonic Distortion (THD)
Spurious-Free Dynamic Range (SFDR)
IAMP DC CHARACTERISTICS
IOUTN Full-Scale Current = IOUTN+ + IOUTN−
IOUTG Full-Scale Current = IOUTG+ + IOUTG−
AC Voltage Compliance Range
IAMPN AC CHARACTERISTICS3
Fundamental
IOUTN SFDR (Third Harmonic)
IAMP GAIN CONTROL CHARACTERISTICS
Minimum Gain
Maximum Gain
Gain Step Size
Gain Step Accuracy
IOUTN Gain Range Error
REFERENCE
Internal Reference Voltage4
Reference Error
Reference Drift
Tx DIGITAL FILTER CHARACTERISTICS (2× Interpolation)
Latency (Relative to 1/fDAC)
−0.2 dB Bandwidth
−3 dB Bandwidth
Stop-Band Rejection (0.289 fDAC to 0.711 fDAC)
Temp
Test Level
Full
Full
Full
25°C
25°C
Full
II
IV
I
V
25°C
25°C
25°C
25°C
25°C
V
V
V
IV
V
−7.5
0
0.5
Monotonic
±2
Full
Full
Full
Full
IV
IV
IV
IV
62.0
62.5
0.5
63.1
63.2
−77.7
79.3
Full
Full
Full
IV
IV
IV
2
2
1
25°C
Full
IV
43.3
25°C
25°C
25°C
25°C
25°C
V
V
V
IV
V
−19.5
0
0.5
Monotonic
0.5
dB
dB
dB
dB
dB
25°C
I
1.23
V
Full
Full
V
V
0.7
30
Full
Full
V
V
43
0.2187
Cycles
fOUT/fDAC
Full
Full
V
V
0.2405
50
fOUT /fDAC
dB
Rev. A | Page 3 of 48
Min
Typ
Max
10
200
25
2
±2
2
−1
67.1
+1.5
Unit
Bits
MSPS
mA
% FS
µA
V
dB
dB
dB
dB
−67.0
105
150
7
13
45.2
dBm
dBc
dBc
dBc
dBc
mA
mA
V
dBm
dBc
3.4
%
ppm/oC
AD9865
Parameter
Tx DIGITAL FILTER CHARACTERISTICS (4× Interpolation)
Latency (Relative to 1/ FDAC)
−0.2 dB Bandwidth
−3 dB Bandwidth
Stop Band Rejection (0.289 fOSCIN to 0.711 fOSCIN)
PLL CLK MULTIPLIER
OSCIN Frequency Range
Internal VCO Frequency Range
Duty Cycle
OSCIN Impedance
CLKOUT1 Jitter5
CLKOUT2 Jitter6
CLKOUT1 and CLKOUT2 Duty Cycle7
Temp
Test Level
Full
Full
Full
Full
V
V
V
V
Full
Full
Full
25°C
25°C
IV
IV
II
V
III
25°C
Full
III
III
Min
Typ
Max
96
0.1095
0.1202
50
5
20
40
Cycles
fOUT/fDAC
fOUT /fDAC
dB
80
200
60
100//3
12
6
45
Unit
55
MHz
MHz
%
ΜΩ/pF
ps rms
ps rms
%
1
Gain error and gain temperature coefficients are based on the ADC only (with a fixed 1.23 V external reference and a 1 V p-p differential analog input).
TxDAC IOUTFS = 20 mA, differential output with 1:1 transformer with source and load termination of 50 Ω, FOUT = 5 MHz, 4x interpolation.
IOUN full-scale current = 80 mA, fOSCIN = 80 MHz, fDAC =160 MHz, 2x interpolation.
4
Use external amplifier to drive additional load.
5
Internal VCO operates at 200 MHz , set to divide-by-1.
6
Because CLKOUT2 is a divided down version of OSCIN, its jitter is typically equal to OSCIN.
7
CLKOUT2 is an inverted replica of OSCIN, if set to divide-by-1.
2
3
Rx PATH SPECIFICATIONS
AVDD = 3.3 V ± 5%, DVDD = CLKVDD = DRVDD = 3.3 V ± 10%; half- or full-duplex operation with CONFIG = 0 default power bias
settings, unless otherwise noted.
Table 2.
Parameter
Rx INPUT CHARACTERISTICS
Input Voltage Span (RxPGA Gain = −10 dB)
Input Voltage Span (RxPGA Gain = +48 dB)
Input Common-Mode Voltage
Differential Input Impedance
Temp
Test Level
Full
Full
25°C
25°C
III
III
III
III
Input Bandwidth (with RxLPF Disabled, RxPGA = 0 dB)
Input Voltage Noise Density (RxPGA Gain = 36 dB, f−3 dBF = 26 MHz)
Input Voltage Noise Density (RxPGA Gain = 48 dB, f−3 dBF = 26 MHz)
RxPGA CHARACTERISTICS
Minimum Gain
Maximum Gain
Gain Step Size
Gain Step Accuracy
Gain Range Error
RxLPF CHARACTERISTICS
Cutoff Frequency (f−3 dBF ) Range
Attenuation at 55.2 MHz with f−3 dBF = 21 MHz
Pass-Band Ripple
Settling Time to 5 dB RxPGA Gain Step @ fADC = 50 MSPS
Settling Time to 60 dB RxPGA Gain Step @ fADC = 50 MSPS
ADC DC CHARACTERISTICS
Resolution
Conversion Rate
25°C
25°C
25°C
III
III
III
25°C
25°C
25°C
25°C
25°C
III
III
III
III
III
Full
25°C
25°C
25°C
25°C
III
III
III
III
III
NA
Full
NA
II
Rev. A | Page 4 of 48
Min
Typ
Max
6.33
8
1.3
400
4.0
53
3.0
2.4
V p-p
mV p-p
V
Ω
pF
MHz
nV/rtHz
nV/rtHz
−12
48
1
Monotonic
0.5
15
dB
dB
dB
dB
dB
35
20
±1
20
100
10
5
Unit
80
MHz
dB
dB
ns
ns
Bits
MSPS
AD9865
Parameter
Rx PATH LATENCY1
Full-Duplex Interface
Half-Duplex Interface
Rx PATH COMPOSITE AC PERFORMANCE @ fADC = 50 MSPS2
RxPGA Gain = 48 dB (Full-Scale = 8.0 mV p-p)
Signal-to-Noise and Distortion (SNR)
Total Harmonic Distortion (THD)
RxPGA Gain = 24 dB (Full-Scale =126 mV p-p)
Signal-to-Noise (SNR)
Total Harmonic Distortion (THD)
RxPGA Gain = 0 dB (Full-Scale = 2.0 V p-p)
Signal-to-Noise and Distortion (SINAD)
Total Harmonic Distortion (THD)
Rx PATH COMPOSITE AC PERFORMANCE @ fADC = 80 MSPS3
RxPGA Gain = 48 dB (Full-Scale = 8.0 mV p-p)
Signal-to-Noise (SNR)
Total Harmonic Distortion (THD)
RxPGA Gain = 24 dB (Full-Scale = 126 mV p-p)
Signal-to-Noise (SNR)
Total Harmonic Distortion (THD)
RxPGA Gain = 0 dB (Full-Scale = 2.0 V p-p)
Signal-to-Noise (SNR)
Total Harmonic Distortion (THD)
Rx-to-Tx PATH FULL-DUPLEX ISOLATION
(1 V p-p, 10 MHz Sine Wave Tx Output)
RxPGA Gain = 40 dB
IOUTP± Pins to RX± Pins
IOUTG± Pins to RX± Pins
RxPGA Gain = 0 dB
IOUTP± Pins to RX± Pins
IOUTG± Pins to RX± Pins
Temp
Test Level
Min
Full
Full
V
V
10.5
10.0
Cycles
Cycles
25°C
25°C
III
III
43.7
−71
dBc
dBc
25°C
25°C
III
III
59
−67.2
dBc
dBc
Full
Full
IV
IV
25°C
25°C
III
III
41.8
−67
dBc
dBc
25°C
25°C
III
III
58.6
−62.9
dBc
dBc
25°C
25°C
II
II
25°C
25°C
III
III
83
37
dBc
dBc
25°C
25°C
III
III
123
77
dBc
dBc
58
58.9
Typ
59
−66
59.6
−69.7
Max
−62.9
−59.8
Unit
dBc
dBc
dBc
dBc
1
Includes RxPGA, ADC pipeline, and ADIO bus delay relative to fADC.
fIN = 5 MHz, AIN = −1.0 dBFS , LPF cutoff frequency set to 15.5 MHz with Reg. 0x08 = 0x80.
3
fIN = 5 MHz, AIN = −1.0 dBFS , LPF cutoff frequency set to 26 MHz with Reg. 0x08 = 0x80.
2
POWER SUPPLY SPECIFICATIONS
AVDD = 3.3 V, DVDD = CLKVDD = DRVDD = 3.3 V; RSET = 2 kΩ, full-duplex operation with fDATA = 80 MSPS,1 unless otherwise noted.
Table 3.
Parameter
SUPPLY VOLTAGES
AVDD
CLKVDD
DVDD
DRVDD
IS_TOTAL (Total Supply Current)
POWER CONSUMPTION
IAVDD + ICLKVDD (Analog Supply Current)
IDVDD + IDRVDD (Digital Supply Current)
Temp
Test Level
Min
Typ
Max
Unit
Full
Full
Full
Full
Full
V
V
V
V
II
3.135
3.0
3.0
3.0
3.3
3.3
3.3
3.3
406
3.465
3.6
3.6
3.6
475
V
V
V
V
mA
Full
IV
IV
311
95
342
133
mA
mA
Rev. A | Page 5 of 48
AD9865
Parameter
POWER CONSUMPTION (Half-Duplex Operation with fDATA = 50 MSPS)2
Tx Mode
IAVDD + ICLKVDD
IDVDD + IDRVDD
Rx Mode
IAVDD + ICLKVDD
IDVDD + IDRVDD
POWER CONSUMPTION OF FUNCTIONAL BLOCKS1 (IAVDD + ICLKVDD)
RxPGA and LPF
ADC
TxDAC
IAMP (Programmable)
Reference
CLK PLL and Synthesizer
MAXIMUM ALLOWABLE POWER DISSIPATION
STANDBY POWER CONSUMPTION
IS_TOTAL (Total Supply Current)
POWER DOWN DELAY (USING PWR_DWN PIN)
RxPGA and LPF
ADC
TxDAC
IAMP
CLK PLL and synthesizer
POWER UP DELAY (USING PWR_DWN PIN)
RxPGA and LPF
ADC
TxDAC
IAMP
CLK PLL and Synthesizer
1
2
Temp
Test Level
25°C
25°C
Min
Typ
Max
Unit
IV
IV
112
46
130
49.5
mA
mA
25°C
25°C
IV
IV
225
36.5
253
39
mA
mA
25°C
25°C
25°C
25°C
25°C
25°C
Full
III
III
III
III
III
III
IV
87
108
38
120
mA
mA
mA
mA
mA
mA
W
10
170
107
1.66
Full
13
mA
25°C
25°C
25°C
25°C
25°C
III
III
III
III
III
440
12
20
20
27
ns
ns
ns
ns
ns
25°C
25°C
25°C
25°C
25°C
III
III
III
III
III
7.8
88
13
20
20
µs
ns
µs
ns
µs
Default power-up settings for MODE = HIGH and CONFIG = LOW, IOUTP_FS = 20 mA, does not include IAMP’s current consumption, which is application dependent.
Default power-up settings for MODE = LOW and CONFIG = LOW.
DIGITAL SPECIFICATIONS
AVDD = 3.3 V ± 5%, DVDD = CLKVDD = DRVDD = 3.3 V ± 10%; RSET = 2 kΩ, unless otherwise noted.
Table 4.
Parameter
CMOS LOGIC INPUTS
High Level Input Voltage
Low Level Input Voltage
Input Leakage Current
Input Capacitance
CMOS LOGIC OUTPUTS (CLOAD = 5 pF)
High Level Output Voltage (IOH = 1 mA)
Low Level Output Voltage (IOH = 1 mA)
Output Rise/Fall Time (High Strength Mode and CLOAD = 15 pF)
Output Rise/Fall Time (Low Strength Mode and CLOAD = 15 pF)
Output Rise/Fall Time (High Strength Mode and CLOAD = 5 pF)
Output Rise/Fall Time (Low Strength Mode and CLOAD = 5 pF)
RESET
Minimum Low Pulse Width (Relative to fADC)
Temp
Test Level
Min
Full
Full
VI
VI
DRVDD – 0.7
Full
VI
Full
Full
Full
Full
Full
Full
VI
VI
VI
VI
VI
VI
Rev. A | Page 6 of 48
Typ
Max
Unit
0.4
12
V
V
µA
pF
3
DRVDD – 0.7
0.4
1.5/2.3
1.9/2.7
0.7/0.7
1.0/1.0
1
V
V
ns
ns
ns
ns
Clock
cycles
AD9865
SERIAL PORT TIMING SPECIFICATIONS
AVDD = 3.3 V ± 5%, DVDD = CLKVDD = DRVDD = 3.3 V ± 10%, unless otherwise noted.
Table 5.
Parameter
WRITE OPERATION (See Figure 46)
SCLK Clock Rate (fSCLK)
SCLK Clock High (tHI)
SCLK Clock Low (tLOW)
SDIO to SCLK Setup Time (tDS)
SCLK to SDIO Hold Time (tDH)
SEN to SCLK Setup Time (tS)
SCLK to SEN Hold Time (tH)
READ OPERATION (See Figure 47 and Figure 48)
SCLK Clock Rate (fSCLK)
SCLK Clock High (tHI)
SCLK Clock Low (tLOW)
SDIO to SCLK Setup Time (tDS)
SCLK to SDIO Hold Time (tDH)
SCLK to SDIO (or SDO) Data Valid Time (tDV)
SEN to SDIO Output Valid to Hi-Z (tEZ)
Temp
Test Level
Min
Full
Full
Full
Full
Full
Full
Full
IV
IV
IV
IV
IV
IV
IV
14
14
14
0
14
0
Full
Full
Full
Full
Full
Full
Full
IV
IV
IV
IV
IV
IV
IV
Typ
Max
Unit
32
MHz
ns
ns
ns
ns
ns
ns
32
MHz
ns
ns
ns
ns
ns
ns
14
14
14
0
14
2
HALF-DUPLEX DATA INTERFACE (ADIO PORT) TIMING SPECIFICATIONS
AVDD = 3.3 V ± 5%, DVDD = CLKVDD = DRVDD = 3.3 V ± 10%, unless otherwise noted.
Table 6.
Parameter
READ OPERATION1 (See Figure 50)
Output Data Rate
Three-State Output Enable Time (tPZL)
Three-State Output Disable Time (tPLZ)
Rx Data Valid Time (tVT)
Rx Data Output Delay (tOD)
WRITE OPERATION (See Figure 49)
Input Data Rate (1× Interpolation)
Input Data Rate (2× Interpolation)
Input Data Rate (4× Interpolation)
Tx Data Setup Time (tDS)
Tx Data Hold Time (tDH)
Latch Enable Time (tEN)
Latch Disable Time (tDIS)
1
Temp
Test Level
Min
Full
Full
Full
Full
Full
II
II
II
II
II
5
Full
Full
Full
Full
Full
Full
Full
II
II
II
II
II
II
II
CLOAD = 5 pF for digital data outputs.
Rev. A | Page 7 of 48
Typ
Max
Unit
80
3
3
MSPS
ns
1.5
4
20
10
5
1
2.5
80
80
50
3
3
ns
ns
ns
MSPS
MSPS
MSPS
ns
ns
ns
ns
AD9865
FULL-DUPLEX DATA INTERFACE (Tx AND Rx PORT) TIMING SPECIFICATIONS
AVDD = 3.3 V ± 5%, DVDD = CLKVDD = DRVDD = 3.3 V ± 10%, unless otherwise noted.
Table 7.
Parameter
Tx PATH INTERFACE (See Figure 53)
Input Nibble Rate (2× Interpolation)
Input Nibble Rate (4× Interpolation)
Tx Data Setup Time (tDS)
Tx Data Hold Time (tDH)
Rx PATH INTERFACE1 (See Figure 54)
Output Nibble Rate
Rx Data Valid Time (tDV)
Rx Data Hold Time (tDH)
1
Temp
Test Level
Min
Full
Full
Full
Full
II
II
II
II
Full
Full
Full
II
II
II
Typ
Max
Unit
20
10
2.5
1.5
160
100
MSPS
MSPS
ns
ns
10
3
0
160
MSPS
ns
ns
CLOAD =5 pF for digital data outputs.
EXPLANATION OF TEST LEVELS
I
II
III
IV
V
VI
100% production tested.
100% production tested at 25°C and guaranteed by design and characterization at specified temperatures.
Sample tested only.
Parameter is guaranteed by design and characterization testing.
Parameter is a typical value only.
100% production tested at 25°C and guaranteed by design and characterization for industrial temperature range.
Rev. A | Page 8 of 48
AD9865
ABSOLUTE MAXIMUM RATINGS
Table 8.
Parameter
ELECTRICAL
AVDD, CLKVDD Voltage
DVDD, DRVDD Voltage
RX+, RX−, REFT, REFB
IOUTP+, IOUTP−
IOUTN+, IOUTN−, IOUTG+,
IOUTG−
OSCIN, XTAL
REFIO, REFADJ
Digital Input and Output Voltage
Digital Output Current
ENVIRONMENTAL
Operating Temperature Range
(Ambient)
Maximum Junction Temperature
Lead Temperature (Soldering, 10 s)
Storage Temperature Range
(Ambient)
Rating
3.9 V maximum
3.9 V maximum
−0.3 V to AVDD + 0.3 V
−1.5 V to AVDD + 0.3 V
−0.3 V to +7 V
−0.3 V to CLVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
5 mA maximum
−40°C to +85°C
Stresses above those listed under the Absolute Maximum
Ratings may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL CHARACTERISTICS
Thermal Resistance: 64-lead LFCSP (4-layer board).
θJA = 24°C/W (paddle soldered to ground plane, 0 LPM air).
θJA = 30.8°C/W (paddle not soldered to ground plane,
0 LPM air).
125°C
150°C
−65°C to +150°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 9 of 48
AD9865
DRVSS
PWR_DWN
CLKOUT2
DVDD
DVSS
CLKVDD
OSCIN
XTAL
CLKVSS
CONFIG
MODE
IOUT_P+
IOUT_P–
IOUT_N+
IOUT_G+
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
ADIO9/Tx[5]
1
48
AVSS
ADIO8/Tx[4]
2
47
AVSS
46
IOUT_N–
PIN 1
IDENTIFIER
ADIO7/Tx[3]
3
ADIO6/Tx[2]
4
45
IOUT_G–
ADIO5/Tx[1]
5
44
AVSS
ADIO4/Tx[0]
6
43
AVDD
ADIO3/Rx[5]
7
42
REFIO
ADIO2/Rx[4]
8
41
REFADJ
ADIO1/Rx[3]
9
40
AVDD
ADIO0/Rx[2] 10
39
AVSS
11
38
RX+
NC/Rx[0] 12
37
RX–
RXEN/RXSYNC 13
36
AVSS
TXEN/TXSYNC 14
35
AVDD
TXCLK/TXQUIET 15
34
AVSS
RXCLK 16
33
REFT
SDO
SCLK
SEN
26
27
28
29
30
31
32
REFB
SDIO
25
AVSS
CLKOUT1
24
RESET
23
PGA[0]
22
PGA[1]
21
PGA[2]
20
PGA[3]
19
PGA[4]
18
GAIN/PGA[5]
17
DRVSS
TOP VIEW
(Not to Scale)
DRVDD
NC/Rx[1]
AD9865
Figure 2. Pin Configuration
Table 9. Pin Function Descriptions
Pin No.
1
2 to 5
6
7
8, 9
10
11
12
13
14
Mnemonic
ADIO9
Tx[5]
ADIO8 to 5
Tx[4 to 1]
ADIO4
Tx[0]
ADIO3
Rx[5]
ADIO2, 1
Rx[4, 3]
ADIO0
Rx[2]
NC
Rx[1]
NC
Rx[0]
RXEN
RXSYNC
TXEN
TXSYNC
Mode1
HD
FD
HD
FD
HD
FD
HD
FD
HD
FD
HD
FD
HD
FD
HD
FD
HD
FD
HD
FD
Description
MSB of ADIO Buffer
MSB of Tx Nibble Input
Bits 8 to 5 of ADIO Buffer
Bits 4 to 1 of Tx Nibble Input
Bit 4 of ADIO Buffer
LSB of Tx Nibble Input
Bit 3 of ADIO Buffer
MSB of Rx Nibble Output
Bits 2 to 1 of ADIO Buffer
Bits 4 to 3 of Rx Nibble Output
LSB of ADIO Buffer
Bit 2 of Rx Nibble Output
No Connect
Bit 1 of Rx Nibble Output
No Connect
LSB of Rx Nibble Output
ADIO Buffer Control Input
Rx Data Synchronization Output
Tx Path Enable Input
Tx Data Synchronization Input
Rev. A | Page 10 of 48
4493-0-002
DRVDD
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AD9865
Pin No.
15
Mnemonic
TXCLK
TXQUIET
Mode1
HD
FD
Description
ADIO Sample Clock Input
Fast TxDAC/IAMP Power-Down
16
RXCLK
HD
FD
17, 64
18, 63
19
20
21
22
23
DRVDD
DRVSS
CLKOUT1
SDIO
SDO
SCLK
SEN
ADIO Request Clock Input
Rx and Tx Clock Output at 2 x fADC
Digital Output Driver Supply Input
Digital Output Driver Supply Return
fADC/N Clock Output (L = 1, 2, 4, or 8)
Serial Port Data Input/Output
Serial Port Data Output
Serial Port Clock Input
Serial Port Enable Input
24
25 to 29
30
GAIN
PGA[5]
PGA[4 to 0]
RESET
FD
HD or FD
HD or FD
Tx Data Port (Tx[5:0]) Mode Select
MSB of PGA Input Data Port
Bits 4 to 0 of PGA Input Data Port
Reset Input (Active Low)
31, 34, 36, 39, 44, 47, 48
32, 33
35, 40, 43
37, 38
41
42
45
46
49
50
51
52
53
AVSS
REFB, REFT
AVDD
RX−, RX+
REFADJ
REFIO
IOUT_G−
IOUT_N−
IOUT_G+
IOUT_N+
IOUT_P−
IOUT_P+
MODE
54
55
56
57
58
59
60
61
62
CONFIG
CLKVSS
XTAL
OSCIN
CLKVDD
DVSS
DVDD
CLKOUT2
PWR_DWN
1
Analog Ground
ADC Reference Decoupling Nodes
Analog Power Supply Input
Receive Path − and + Analog Inputs
TxDAC Full-Scale Current Adjust
TxDAC Reference Input/Output
−Tx Amp Current Output_Sink
−Tx Mirror Current Output_Sink
+Tx Amp Current Output_Sink
+Tx Mirror Current Output_Sink
−TxDAC Current Output_Source
+TxDAC Current Output_Source
Digital Interface Mode Select Input
LOW = HD, HIGH = FD
Power-Up SPI Register Default Setting Input
Clock Oscillator/Synthesizer Supply Return
Crystal Oscillator Inverter Output
Crystal Oscillator Inverter Input
Clock Oscillator/Synthesizer Supply
Digital Supply Return
Digital Supply Input
fOSCIN/L Clock Output, (L = 1, 2, or 4)
Power-Down Input
HD = half-duplex mode; FD = full-duplex mode.
Rev. A | Page 11 of 48
AD9865
TYPICAL PERFORMANCE CHARACTERISTICS
Rx PATH TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = CLKVDD = DVDD = DRVDD = 3.3 V, fOSCIN = fADC = 50 MSPS, low-pass filter’s f−3 dB = 22 MHz, AIN = −1 dBFS,
RIN = 50 Ω, half- or full-duplex interface, default power bias settings.
62
–30
56
SINAD (dBFS)
–20
59
–40
–50
–60
–70
–80
04493-0-040
–90
0
6.25
12.50
FREQUENCY (MHz)
18.75
8.5
50
8.0
47
7.5
44
7.0
41
–6
25.00
0
6
12
18
24
30
36
Figure 3. Spectral Plot with 4 k FFT of Input Sinusoid with
RxPGA = 0 dB and PIN = 9 dBm
Figure 6. SINAD/ENOB vs. RxPGA Gain and Frequency
–55
–30
RBW = 12.2kHz
1MHz
5MHz
10MHz
15MHz
20MHz
–60
–50
–60
–65
THD (dBFC)
–70
–80
–90
–70
–75
–100
–110
–80
04493-0-041
–120
0
5
10
15
FREQUENCY (MHz)
20
–85
–6
25
–56
59
60
–62
56
57
–68
54
–74
51
–80
–18
–15
–12
THD @ 3.14V
THD @ 3.3V
THD @ 3.46V
–9
–6
–3
–86
0
–92
SINAD (dBFS)
63
THD (dBFS)
62
04493-0-042
SINAD (dBFS)
–50
45
–21
6
12
18
24
30
36
42
48
Figure 7. THD vs. RxPGA Gain and Frequency
66
SINAD @ 3.14V
SINAD @ 3.3V
SINAD @ 3.46V
0
RxPGA GAIN (dB)
Figure 4. Spectral Plot with 4 k FFT of 84-Carrier DMT Signal
with PAR = 10.2 dB, PIN = −33.7 dBm, and RxPGA = 36 dB
48
04493-0-044
INPUT REFERRED SPECTRUM (dBm)
–40
–130
6.5
48
42
RxPGA GAIN (dB)
–55
THD @ +25°C
THD @ +85°C
THD @ –40°C
53
–60
50
–65
47
–70
44
–75
41
–6
INPUT AMPLITUDE (dBFS)
0dBFS = 2V p-p
–45
SINAD @ +25°C
SINAD @ +85°C
SINAD @ –40°C –50
0
6
12
18
24
30
36
42
RxPGA GAIN (dB)
Figure 5. SINAD and THD vs. Input Amplitude and Supply
(fIN = 8 MHz, LPF f−3 dB = 26 MHz; Rx PGA = 0 dB)
Figure 8. SINAD/THD Performance vs. RxPGA Gain
and Temperature ( fIN = 5 MHz)
Rev. A | Page 12 of 48
–80
48
THD (dBc)
–100
53
04493-0-045
INPUT REFERRED SPECTRUM (dBm)
0
–10
10.0
1MHz
5MHz
10MHz 9.5
15MHz
20MHz
9.0
ENOB (Bits)
FUND = –1dBFS
SINAD = 59.1dBFS
ENOB = 9.53 BITS
SNR = 60.2dBFS
THD = –65.2dBFS
SFDR = –64.9dBc (THIRD HARMONIC)
RBW = 12.21kHz
04493-0-043
10
AD9865
Rx PATH TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = CLKVDD = DVDD = DRVDD = 3.3 V, fOSCIN = fADC = 80 MSPS, low-pass filter’s f−3 dB = 30 MHz, AIN = −1 dBFS,
RIN = 50 Ω, half- or full-duplex interface, default power bias settings.
–20
SINAD (dBFS)
–30
59
–40
–50
–60
–70
–80
04493-0-046
INPUT REFERRED SPECTRUM (dBm)
–10
–90
–100
0
10
20
FREQUENCY (MHz)
30
9.5
56
9.0
53
8.5
50
8.0
47
7.5
44
7.0
41
–6
40
10.0
5MHz
10MHz
15MHz
20MHz
30MHz
0
6
12
18
24
30
36
ENOB (Bits)
FUND = –1dBFS
SINAD = 59.3dBFS
ENOB = 9.56 BITS
SNR = 59.8dBFS
THD = –69.1dBFS
SFDR = –70.3dBc (THIRD HARMONIC)
RBW = 19.53kHz
0
04493-0-049
62
10
6.5
48
42
RxPGA GAIN (dB)
Figure 9. Spectral Plot with 4k FFT of Input Sinusoid
with RxPGA = 0 dB and PIN = 9 dBm
Figure 12. SINAD/ENOB vs. RxPGA Gain and Frequency
–55
–30
RBW = 19.53kHz
–60
–50
–60
–65
THD (dBc)
–70
–80
–90
–70
–110
–120
10
20
FREQUENCY (MHz)
30
–85
–6
40
62
–56
59
–62
56
57
–68
54
–74
51
48
–18
–15
–12
–9
–6
–3
0
SINAD (dBFS)
SINAD (dBFS)
–50
THD (dBFS)
THD @ 3.14V
THD @ 3.3V
THD @ 3.46V
60
45
–21
12
18
24
30
36
42
48
Figure 13. THD vs. RxPGA Gain and Frequency
–40
SINAD @ +25°C
SINAD @ +85°C
SINAD @ –40°C –45
–50
THD @ +25°C
THD @ +85°C
THD @ –40°C
53
–55
50
–60
–80
47
–65
–86
44
–70
–92
04493-0-048
66
63
6
RxPGA GAIN (dB)
Figure 10. Spectral Plot with 4k FFT of 111-Carrier DMT Signal with
PAR = 11 dB, PIN = −33.7 dBm, LPF f−3 dB = 32 MHz, and RxPGA = 36 dB
SINAD @ 3.14V
SINAD @ 3.3V
SINAD @ 3.46V
0
41
–6
6
12
18
24
30
36
42
–75
48
RxPGA GAIN (dB)
INPUT AMPLITUDE (dBFS)
0dBFS = 2V p-p
Figure 11. SINAD and THD vs. Input Amplitude and Supply
(fIN = 8 MHz, LPF f−3 dB = 26 MHz; RxPGA = 0 dB)
0
THD (dBc)
0
04493-0-051
–130
5MHz
10MHz
15MHz
20MHz
30MHz
–80
04493-0-050
–75
–100
04493-0-047
INPUT REFERRED SPECTRUM (dBm)
–40
Figure 14. SINAD/THD Performance vs. RxPGA Gain and Temperature
( fIN = 10 MHz)
Rev. A | Page 13 of 48
AD9865
60.0
60.0
–52
SNR @ 3.13V
SNR @ 3.3V –54
SNR @ 3.47V
–56
59.5
–58
58.5
–64
57.5
–66
56.5
57.0
–68
56.0
56.5
–70
6
12
18
24
30
36
42
55.5
55.0
20
30
40
60
–70
80
70
Figure 15. SNR and THD vs. Input Frequency and Supply
( LPF f−3 dB = 26 MHz; RxPGA = 0 dB)
Figure 18. SNR and THD vs. Sample Rate and Supply
(LPF Disabled; RxPGA = 0 dB; fIN = 8 MHz)
16
76.6
14
AD9865: +25°C
AD9865: +85°C
AD9865: –40°C
65.6
12
54.7
10
43.8
8
32.8
6
21.9
4
10.9
2
0
–6
0
6
12
18
24
30
36
0
48
42
44
43
42
41
40
39
04493-0-056
87.5
SNR (dBc)
18
45
NOISE SPECTRAL DENSITY (nV/ Hz)
98.5
38
0
10
20
Figure 16. Input Referred Integrated Noise and Noise Spectral Density vs.
RxPGA Gain (LPF f−3 dB = 26 MHz)
0.4
3
0.3
GAIN STEP ERROR (dB)
0.5
4
2
1
0
–1
–2
DEVICE 1
DEVICE 2
DEVICE 3
DEVICE 4
–5
–6
0
6
12
18
24
50
60
70
80
30
0.2
0.1
0
–0.1
–0.2
–0.3
04493-0-054
–4
40
Figure 19. SNR vs. Filter Cutoff Frequency
(50 MSPS; fIN = 5 MHz; AIN = −1 dB; RxPGA = 48 dB)
5
–3
30
CUTOFF FREQUENCY (MHz)
RxPGA GAIN (dB)
DC OFFSET (% of full-scale)
50
INPUT FREQUENCY (MHz)
20
–50
–60
INPUT FREQUENCY (MHz)
109.4
INTEGRATED NOISE (µV rms)
THD @ 3.13V
THD @ 3.3V
THD @ 3.46V
57.0
36
42
AD9865: GAIN STEP ERROR @ +25°C
AD9865: GAIN STEP ERROR @ +85°C
AD9865: GAIN STEP ERROR @ –40°C
–0.4
–0.5
–6
48
GAIN (dB)
0
6
12
18
24
30
36
42
RxPGA GAIN (dB)
Figure 17. Rx DC Offset vs. RxPGA Gain
Figure 20. RxPGA Gain Step Error vs. Gain (fIN = 10 MHz)
Rev. A | Page 14 of 48
04493-0-057
0
57.5
THD (dBc)
58.0
04493-0-052
–62
–72
48
–40
58.0
58.5
56.0
–6
–30
SNR @ 3.13V
SNR @ 3.3V
SNR @ 3.46V
48
04493-0-055
–60
59.0
SNR (dBFS)
THD @ 3.13V
THD @ 3.3V
THD @ 3.47V
59.0
–20
59.5
04493-0-053
SNR (dBFS)
60.5
THD (dBc)
61.0
AD9865
Rx PATH TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = CLKVDD = DVDD = DRVDD = 3.3 V, fOSCIN = fADC = 50 MSPS, low-pass filter disabled, RxPGA = 0 dB, AIN = −1 dBFS,
RIN = 50 Ω, half- or full-duplex interface, default power bias settings.
512
352
320
448
288
384
320
CODE
CODE
256
256
224
192
160
192
04493-0-058
0
80
160
240
320
400
480
560
640
96
64
720
0
80
160
240
320
TIME (ns)
Figure 21. RxPGA Settling Time −12 dB to +48 dB Transition for DC Input
(fADC = 50 MSPS, LPF Disabled)
640
–4
–6
–9
–12
–6
–8
–10
+18dB GAIN
+30dB GAIN
+42dB GAIN
–12
–14
04493-0-059
5
10
15
20
25
30
35
40
45
–18
–20
50
0
5
10
15
20
25
30
35
40
45
Figure 25. Rx Low-Pass Filter Amplitude Response vs. RxPGA Gain
(LPF's f−3 dB = 33 MHz)
Figure 22. Rx Low-Pass Filter Amplitude Response vs. Supply
(fADC = 50 MSPS, f−3 dB = 33 MHz, RxPGA = 0 dB)
140
130
TxDAC ISOLATION @ 0dB
120
420
10
410
9
400
8
7
RESISTANCE (Ω)
390
110
100
90
RIN
380
6
370
5
4
360
CIN
350
80
04493-0-060
IAMP ISOLATION @ 0dB
70
0
5
10
15
20
25
50
INPUT FREQUENCY (MHz)
INPUT FREQUENCY (MHz)
30
340
2
330
1
320
35
FREQUENCY (MHz)
3
5
15
25
35
45
55
65
75
85
FREQUENCY (MHz)
Figure 23. Rx to Tx Full-Duplex Isolation @ 0 RxPGA Setting
(Note: ATTEN @ RxPGA = x dB = ATTEN @ RxPGA = 0 dB − RxPGA Gain)
Figure 26. Rx Input Impedance vs. Frequency
Rev. A | Page 15 of 48
95
0
105
CAPACITANCE (pF)
0
04493-0-062
–16
–15
60
720
–6dB GAIN
0dB GAIN
+6dB GAIN
–2
FUNDAMENTAL (dB)
AMPLITUDE RESPONSE (dB)
560
0
3.3V
3.0V
3.6V
–3
ATTEN @RxPGA = 0dB (dB)
480
Figure 24. RxPGA Settling Time for 0 dB to +5 dB Transition for DC Input
(fADC = 50 MSPS, LPF Disabled)
0
–18
400
TIME (ns)
04493-0-090
64
04493-0-061
128
128
AD9865
TxDAC PATH TYPICAL PERFORMANCE CHARACTERISTICS
10
10
0
0
–10
–10
–20
–20
–30
–30
dBm
–40
–40
–50
–60
–60
04493-0-072
–50
–70
–80
0
5
10
15
20
04493-0-075
dBm
AVDD = CLKVDD = DVDD = DRVDD = 3.3 V, fOSCIN = 50 MSPS and 80 MSPS, RSET = 1.96 kΩ, 2:1 transformer coupled output
(see Figure 63) into 50 Ω load half- or full-duplex interface, default power bias settings.
–70
–80
30
0
5
10
FREQUENCY (MHz)
–65
–65
–70
–70
IMD (dBFS)
–75
4dBm
7dBm
–80
10dBm
0
2.5
5.0
7.5
10.0
12.5
15.0
17.5
35
40
–75
4dBm
7dBm
–80
04493-0-076
–90
20.0
0
5
15
20
25
30
Figure 31. 2-Tone IMD Frequency Sweep vs. Peak Power
with fDATA = 80 MSPS, 2× Interpolation
–70
–70
SFDR (dBFS)
–65
–75
4dBm
7dBm
–80
10dBm
–75
4dBm
–80
7dBm
0
2.5
5.0
7.5
10.0
12.5
15.0
17.5
–90
20.0
2-TONE CENTER FREQUENCY (MHz)
04493-0-077
–85
04493-0-074
–85
(RELATIVE TO PEAK POWER)
–65
10dBm
10
2-TONE CENTER FREQUENCY (MHz)
Figure 28. 2-Tone IMD Frequency Sweep vs. Peak Power
with fDATA = 50 MSPS, 4× Interpolation
SFDR (dBFS)
30
10dBm
2-TONE CENTER FREQUENCY (MHz)
(RELATIVE TO PEAK POWER)
25
–85
04493-0-073
–85
–90
20
Figure 30. Dual-Tone Spectral Plot of TxDAC's Output
(fDATA = 80 MSPS, 2× Interpolation, 10 dBm Peak Power,
F1 = 27.1 MHz, F2 = 28.7 MHz)
(RELATIVE TO PEAK POWER)
IMD (dBFS)
(RELATIVE TO PEAK POWER)
Figure 27. Dual-Tone Spectral Plot of TxDAC's Output
(fDATA = 50 MSPS, 4× Interpolation, 10 dBm Peak Power,
F1 = 17 MHz, F2 = 18 MHz)
–90
15
FREQUENCY (MHz)
0
5
10
15
20
25
30
2-TONE CENTER FREQUENCY (MHz)
Figure 29. 2-Tone Worst Spur Frequency Sweep vs. Peak Power
with fDATA = 50 MSPS, 4× Interpolation
Figure 32. 2-Tone Worst Spur Frequency Sweep vs. Peak Power
with fDATA = 80 MSPS, 2× Interpolation
Rev. A | Page 16 of 48
AD9865
–20
–20
–30
–40
–50
–50
dBm
–40
–60
–60
–70
–80
–80
04493-0-078
–70
–90
–100
0
5
10
15
20
04493-0-081
–30
dBm
PAR = 11.4
RMS = –1.4dBm
PAR = 11.4
RMS = –1.4dBm
–90
–100
25
0
5
10
FREQUENCY (MHz)
15
20
25
Figure 33. Spectral Plot of 84-Carrier OFDM Test Vector
(fDATA = 50 MSPS, 4× Interpolation)
40
–20
PAR = 11.4
RMS = –1.4dBm
PAR = 11.4
RMS = –1.4dBm
–30
–30
–40
–40
–50
–50
dBm
–60
–60
–70
–80
–80
04493-0-079
–70
–90
0
25
50
75
100
125
150
175
04493-0-082
dBm
35
Figure 36. Spectral Plot of 111-Carrier OFDM Test Vector
(fDATA = 80 MSPS, 2× Interpolation)
–20
–100
30
FREQUENCY (MHz)
–90
–100
200
0
20
40
FREQUENCY (MHz)
60
80
100
120
140
160
FREQUENCY (MHz)
Figure 34. Wideband Spectral Plot of 88-Subcarrier OFDM Test Vector
(fDATA = 50 MSPS, 4× Interpolation)
Figure 37. Wideband Spectral Plot of 111-Carrier OFDM Test Vector
(fDATA = 80 MSPS, 2× Interpolation)
100
95
2-TONE IMD
95
90
80
75
70
SNR
04493-0-080
65
60
55
–24
–21
–18
–15
–12
–9
–6
–3
85
80
75
70
SNR
65
04493-0-083
85
(RELATIVE TO PEAK POWER)
SNR AND 2-TONE IMD (dBFS)
90
(RELATIVE TO PEAK POWER)
SNR AND 2-TONE IMD (dBFS)
2-TONE IMD
60
55
–24
0
AOUT (dBFS)
–21
–18
–15
–12
–9
–6
–3
AOUT (dBFS)
Figure 35. SNR and SFDR vs. POUT
(fOUT = 12.55 MHz, fDATA = 50 MSPS, 4× Interpolation)
Figure 38. SNR and SFDR vs. POUT
(fOUT = 20 MHz, fDATA = 80 MSPS, 2× Interpolation)
Rev. A | Page 17 of 48
0
AD9865
IAMP PATH TYPICAL PERFORMANCE CHARACTERISTICS
48
RBW = 2.3kHz
2.5MHz
46
5MHz
44
42
OIP3 (dBm)
40
10MHz
38
20MHz
15MHz
36
34
0
5
10
15
20
04493-0-087
20
15
10
5
0
–5
–10
–15
–20
–25
–30
–35
–40
–45
–50
–55
–60
04493-0-084
dBm
AVDD = CLKVDD = DVDD = DRVDD = 3.3 V, fOSCIN = 50 MSPS, RSET = 1.58 kΩ, 1:1 transformer coupled output (see Figure 64 and
Figure 65) into 50 Ω load, half- or full-duplex interface, default power bias settings.
32
30
3.0
25
3.5
4.0
4.5
5.0
VCM (V)
FREQUENCY (MHz)
Figure 39. Dual-Tone Spectral Plot of IAMPN Output
(IAMP Settings of I = 12.5 mA, N = 4, G = 0,
2:1 Transformer into 75 Ω Loader, VCM = 4.8 V)
Figure 42. IOUTN Third-Order Intercept vs. Common-Mode Voltage
(IAMP Settings of I = 12.5 mA, N = 4, G = 0, 2:1
Transformer into 75 Ω Load)
0
42
PAR = 11.4
RMS = 10.3dBm
–10
40
2.5MHz
–20
38
OIP3 (dBm)
–40
–50
5MHz
36
10MHz
34
–60
15MHz
–80
32
04493-0-085
–70
0
5
10
15
20
20MHz
30
3.0
25
3.5
4.0
FREQUENCY (MHz)
5.0
Figure 43. IOUTG Third-Order Intercept vs. Common-Mode Voltage
(IAMP Settings of I = 4.25 mA, N = 0, G = 6,
2:1 Transformer into 75 Ω Load)
0
0
PAR = 11.4
RMS = 10.4dBm
–20
–30
–30
dBm
–20
–40
–40
–50
–60
–60
04493-0-086
–50
–70
0
5
10
15
20
PAR = 11.4
RMS = 9.8dBm
RBW = 10kHz
–10
25
04493-0-089
–10
dBm
4.5
VCM (V)
Figure 40. Spectral Plot of 84-Carrier OFDM Test Vector Using IAMPN in
Current-Mode Configuration
(IAMP Settings of I = 10 mA, N = 4, G = 0; VCM = 4.8 V)
–80
04493-0-088
dBm
–30
–70
–80
0
5
10
15
20
25
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 41. Spectral Plot of 84-Carrier OFDM Test Vector Using IAMP in
Voltage-Mode Configuration with AVDD = 5 V
(PBR951 Transistors, IAMP Settings of I = 6 mA, N = 2, G = 6)
Rev. A | Page 18 of 48
Figure 44. Spectral Plot of 84-Carrier OFDM Test Vector Using IAMP in
Voltage-Mode Configuration with AVDD = 3.3 V
(PBR951 Transistors, IAMP Settings of I = 6 mA, N = 2, G = 6)
AD9865
SERIAL PORT
Table 10. SPI Register Mapping
Address
(Hex)1
Bit
Breakdown
Power-Up Default Value
MODE = 0 (Half-Duplex)
Description
Width
CONFIG = 0
SPI PORT CONFIGURATION AND SOFTWARE RESET
0x00
(7)
4-Wire SPI
1
0
(6)
LSB First
1
0
(5)
S/W Reset
1
0
POWER CONTROL REGISTERS (via PWR_DWN pin)
0x01
(7)
1
0
Clock Syn.
0x02
(6)
(5)
(4)
(3)
(2)
(1)
(0)
(7)
TxDAC/IAMP
Tx Digital
REF
ADC CML
ADC
PGA Bias
RxPGA
CLK Syn.
(6)
TxDAC/IAMP
(5)
Tx Digital
(4)
REF
(3)
ADC CML
(2)
ADC
(1)
PGA Bias
(0)
RxPGA
HALF-DUPLEX POWER CONTROL
0x03
(7:3)
Tx OFF Delay
(2)
Rx _TXEN
(1)
Tx PWRDN
(0)
Rx PWRDN
0x05
(2)
(1)
(0)
0x06
(7:6)
(5)
(4)
(3:2)
(1)
(0)
Rx PATH CONTROL
0x07
(5)
(4)
(0)
CONFIG = 0
CONFIG = 1
Comments
0
0
0
0
0
0
0
0
0
Default SPI configuration is
3-wire, MSB first.
0
0
0
PWR_DWN = 0.
Default setting is for all
blocks powered on.
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1*
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
5
1
1
1
0xFF
PLL CLOCK MULTIPLIER/SYNTHESIZER CONTROL
0x04
(5)
Duty Cycle Enable
1
0
(4)
fADC from PLL
1
0
(3:2)
(1:0)
MODE = 1 (Full-Duplex)
CONFIG = 1
0xFF
N/A
N/A
0
0
0
0
0
0
PLL Divide-N
PLL Multiplier-M
2
2
00
01
00
10*
00
01
00
01
OSCIN to RXCLK
Invert RXCLK
Disabled RXCLK
CLKOUT2 Divide
CLKOUT2 Invert
CLKOUT2 Disable
CLKOUT1 Divide
CLKOUT1 Invert
CLKOUT1 Disable
1
1
1
2
1
1
2
1
1
0
0
0
01
0
0
01
0
0
0
0
0
01
0
0
01
0
0
0
0
0
01
0
0
01
0
0
1*
0
0
01
0
1*
01
0
1*
Initiate Offset Cal.
Rx Low Power
Rx Filter ON
1
1
1
0
0
1
0
1*
1
0
0
1
0
1*
1
Rev. A | Page 19 of 48
PWR_DWN = 1.
Default setting* is for all
functional blocks powered
down except PLL.
*MODE = CONFIG = 1.
Setting has PLL powered
down with OSCIN input
routed to RXCLK output.
Default setting is for TXEN
input to control power
on/off of Tx/Rx path.
Tx driver delayed by 31
1/fDATA clock cycles.
Default setting is Duty Cycle
Restore disabled, ADC CLK
from OSCIN input, and PLL
multiplier × 2 setting.
*PLL multiplier × 4 setting.
Full-duplex RXCLK normally
at nibble rate.
*Exception on power-up.
Default setting is CLKOUT2
and CLKOUT1 enabled with
divide-by-2.
*CLKOUT1 and CLKOUT2
disabled.
Default setting has LPF ON
and Rx path at nominal
power bias setting.
*Rx path to low power.
AD9865
Address
(Hex)1
Bit
Breakdown
0x08
(7:0)
Power-Up Default Value
MODE = 0 (Half-Duplex)
Description
Width
Rx Filter Tuning
Cut-off Frequency
8
Tx/Rx PATH GAIN CONTROL
0x09
(6)
Use SPI Rx Gain
(5:0)
Rx Gain Code
0x0A
(6)
Use SPI Tx Gain
(5:0)
Tx Gain Code
Tx AND Rx PGA CONTROL
0x0B
(6)
PGA Code for Tx
(5)
PGA Code for Rx
(3)
Force GAIN strobe
(2)
Rx Gain on Tx Port
(1)
3-Bit RxPGA Port
Tx DIGITAL FILTER AND INTERFACE
0x0C
(7:6)
Interpolation
Factor
(4)
Invert
TXEN/TXSYNC
(3)
Tx 5/5 Nibble*
(2)
LS Nibble First*
(1)
TXCLK neg. edge
(0)
Twos complement
CONFIG = 1
CONFIG = 0
CONFIG = 1
Comments
0x80
0x61
0x80
0x80
Refer to Low-Pass Filter
section.
1
6
0x00
0x00
0x00
0x00
1
6
0x7F
0x7F
0x7F
0x7F
Default setting is for
hardware Rx gain code via
PGA or Tx data port.
Default setting is for Tx gain
code via SPI control.
1
1
1
1
1
0
1
0
0
0
0
1
0
0
1**
0
1
0
1*
0
0
1
0
1*
0
Default setting is RxPGA
control active.
*Tx port with GAIN strobe
(AD9875/AD9876-compatible).
** 3-bit RxPGA gain map
(AD9975-compatible).
2
01
00
01
01
1
0
0
0
0
1
1
1
1
N/A
N/A
0
0
N/A
N/A
0
0
0
0
0
1
0
0
0
1
Default setting is 2×
interpolation with LPF
response. Data format is
straight binary for halfduplex and twos
complement for full-duplex
interface.
*Full-duplex only.
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0x00
0
0x00
0x44
0x44
0x62
0x62
0x01
0x01
Rx INTERFACE AND ANALOG/DIGITAL LOOPBACK
0x0D
(7)
Analog Loopback
1
0
0
(6)
Digital Loopback*
1
0
0
(5)
Rx Port 3-State
1
N/A
N/A
(4)
1
0
0
Invert
RXEN/RXSYNC
(3)
RX 5/5 Nibble
1
N/A
N/A
(2)
LS Nibble First*
1
N/A
N/A
(1)
RXCLK neg. edge
1
0
0
(0)
Twos complement 1
0
0
DIGITAL OUTPUT DRIVE STRENGTH, TxDAC OUTPUT, AND REV ID
0x0E
(7)
1
0
0
Low Drive
Strength
(0)
TxDAC Output
1
0
0
0x0F
(3:0)
REV ID Number
4
0x00
0x00
Tx IAMP GAIN AND BIAS CONTROL
0x10
(7)
Select Tx Gain
1
0x44
0x44
(6:4)
G1
3
(2:0)
N
3
0x11
(6:4)
G2
3
0x62
0x62
(2:0)
G3
3
0x12
(6:4)
(2:0)
Stand_Secondary
Stand_Primary
MODE = 1 (Full-Duplex)
CONFIG = 0
3
3
0x01
0x01
Rev. A | Page 20 of 48
Data format is straight
binary for half-duplex and
twos complement for fullduplex interface.
Analog loopback: ADC Rx
data fed back to TxDAC.
Digital loopback: Tx input
data to Rx output port.
*Full-duplex only.
Default setting is for high
drive strength and IAMP
enabled.
Secondary path G1 = 0, 1, 2,
3, 4.
Primary path N = 0, 1, 2, 3, 4.
Secondary path stages:
G2 = 0 to 1.50 in 0.25 steps
and G3 = 0 to 6.
Standing current of primary
and secondary path.
AD9865
Address
(Hex)1
0x13
1
Power-Up Default Value
Bit
Breakdown
Description
Width
CONFIG = 0
CONFIG = 1
CONFIG = 0
CONFIG = 1
(7:5)
(4:3)
(2:0)
CPGA Bias Adjust
SPGA Bias Adjust
ADC Bias Adjust
3
2
4
0x00
0x00
0x00
0x00
MODE = 0 (Half-Duplex)
MODE = 1 (Full-Duplex)
Comments
Current bias setting for Rx
path’s functional blocks.
Refer to page 41.
Bits that are undefined should always be assigned a 0.
Table 11. SPI Registers Pertaining to SPI Options
REGISTER MAP DESCRIPTION
The AD9865 contains a set of programmable registers described
in Table 10 that are used to optimize its numerous features,
interface options, and performance parameters from its default
register settings. Registers pertaining to similar functions have
been grouped together and assigned adjacent addresses to
minimize the update time when using the multibyte serial port
interface (SPI) read/write feature. Bits that are undefined within
a register should be assigned a 0 when writing to that register.
The default register settings were intended to allow some
applications to operate without the use of an SPI. The AD9865
can be configured to support a half- or full-duplex digital
interface via the MODE pin, with each interface having two
possible default register settings determined by the setting of
the CONFIG pin.
For instance, applications that need to use only the Tx or Rx
path functionality of the AD9865 can configure it for a halfduplex interface (MODE = 0), and use the TXEN pin to select
between the Tx or Rx signal path with the unused path
remaining in a reduced power state. The CONFIG pin can be
used to select the default interpolation ratio of the Tx path and
RxPGA gain mapping.
SERIAL PORT INTERFACE (SPI)
The serial port of the AD9865 has 3- or 4-wire SPI capability
allowing read/write access to all registers that configure the
device’s internal parameters. Registers pertaining to the SPI are
listed in Table 11. The default 3-wire serial communication port
consists of a clock (SCLK), serial port enable (SEN), and a bidirectional data (SDIO) signal. SEN is an active low control
gating read and write cycle. When SEN is high, SDO and SDIO
are three-stated. The inputs to SCLK, SEN, and SDIO contain a
Schmitt trigger with a nominal hysteresis of 0.4 V centered
about VDDH/2. The SDO pin remains three-stated in a 3-wire
SPI interface.
Address (Hex)
0x00
Bit
(7)
(6)
Description
Enable 4-wire SPI
Enable SPI LSB first
A 4-wire SPI can be enabled by setting the 4-wire SPI bit high,
causing the output data to appear on the SDO pin instead of on
the SDIO pin. The SDIO pin serves as an input-only throughout
the read operation. Note that the SDO pin is active only during
the transmission of data and remains three-stated at any other
time.
An 8-bit instruction header must accompany each read and
write operation. The instruction header is shown in Table 12.
The MSB is an R/W indicator bit with logic high indicating a
read operation. The next two bits, N1 and N0, specify the
number of bytes (one to four bytes) to be transferred during the
data transfer cycle. The remaining five bits specify the address
bits to be accessed during the data transfer portion. The data
bits immediately follow the instruction header for both read
and write operations.
Table 12. Instruction Header Information
MSB
17
R/W
16
N1
15
N0
14
A4
13
A3
12
A2
LSB
11
A1
10
A0
The AD9865 serial port can support both MSB (most
significant bit) first and LSB (least significant bit) first data
formats. Figure 45 illustrates how the serial port words are built
for the MSB first and LSB first modes. The bit order is controlled by the SPI LSB first bit (Register 0, Bit 6). The default
value is 0, MSB first. Multibyte data transfers in MSB format
can be completed by writing an instruction byte that includes
the register address of the last address to be accessed. The
AD9865 automatically decrements the address for each successive byte required for the multibyte communication cycle.
Rev. A | Page 21 of 48
AD9865
Figure 47 illustrates the timing for a 3-wire read operation to
the SPI port. After SEN goes low, data (SDIO) pertaining to the
instruction header is read on the rising edges of SCLK. A read
operation occurs, if the read/not-write indicator is set high.
After the address bits of the instruction header are read, the
eight data bits pertaining to the specified register are shifted out
of the SDIO pin on the falling edges of the next eight clock cycles.
If a multibyte communication cycle is specified in the instruction
header, a similar process as previously described for a multibyte
SPI write operation applies. The SDO pin remains three-stated
in a 3-wire read operation.
DATA TRANSFER CYCLE
SCLK
R/W N1
N2
A4
A3
A2
A1
A0
INSTRUCTION CYCLE
SEN
D1N D0N
D71 D61
DATA TRANSFER CYCLE
SCLK
A0
A1
A2
A3
A4
N2
N1
D6N D7N
R/W D01 D11
4493-0-003
SDATA
tS 1/fSCLK
Figure 45. SPI Timing, MSB First (Upper), and LSB First (Lower)
SEN
When the SPI LSB first bit is set high, the serial port interprets
both instruction and data bytes LSB first. Multibyte data transfers in LSB format can be completed by writing an instruction
byte that includes the register address of the first address to be
accessed. The AD9865 automatically increments the address for
each successive byte required for the multibyte communication
cycle.
Figure 46 illustrates the timing requirements for a write operation to the SPI port. After the serial port enable (SEN) signal
goes low, data (SDIO) pertaining to the instruction header is
read on the rising edges of the clock (SCLK). To initiate a write
operation, the read/not-write bit is set low. After the instruction
header is read, the eight data bits pertaining to the specified
register are shifted into the SDIO pin on the rising edge of the
next eight clock cycles. If a multibyte communication cycle is
specified, the destination address is decremented (MSB first)
and shifts in another eight bits of data. This process repeats until
all the bytes specified in the instruction header (N1, N0 bits) are
shifted into the SDIO pin. SEN must remain low during the data
transfer operation, only going high after the last bit is shifted
into the SDIO pin.
tS 1/fSCLK
tDH
R/W
N1
N0
A0
D7
D6 D1
D0
tEZ
N1
A2
A1
A0
D7
D6
D1
D0
Figure 48 illustrates the timing for a 4-wire read operation to
the SPI port. The timing is similar to the 3-wire read operation
with the exception that data appears at the SDO pin, while the
SDIO pin remains high impedance throughout the operation.
The SDO pin is an active output only during the data transfer
phase and remains three-stated at all other times.
tS 1/fSCLK
SEN
tLOW
tHI
SCLK
tDS
SDIO
tEZ
tDH
R/W
N1
A2
A1
A0
tEZ
tDV
SDO
4493-0-004
SDIO
R/W
Figure 47. SPI 3-Wire Read Operation Timing
SCLK
tDS
tDH
SDIO
tLOW
tHI
tDV
tDS
tH
SEN
tLOW
tHI
SCLK
4493-0-005
SDATA
Figure 46. SPI Write Operation Timing
Rev. A | Page 22 of 48
D7
D6
D1
D0
Figure 48. SPI 4-Wire Read Operation Timing
4493-0-006
INSTRUCTION CYCLE
SEN
AD9865
DIGITAL INTERFACE
HALF-DUPLEX MODE
The half-duplex mode functions as follows when the MODE
pin is tied low. The bidirectional ADIO port is typically shared
in burst fashion between the transmit path and receive path.
Two control signals, TXEN and RXEN, from a DSP (or digital
ASIC) control the bus direction by enabling the ADIO port’s
input latch and output driver, respectively. Two clock signals are
also used: TXCLK to latch the Tx input data, and RXCLK to
clock the Rx output data. The ADIO port can also be disabled
by setting TXEN and RXEN low (default setting), thus allowing
it to be connected to a shared bus.
Internally, the ADIO port consists of an input latch for the Tx
path in parallel with an output latch with three-state outputs for
the Rx path. TXEN is used to enable the input latch; RXEN is
used to three-state the output latch. A five-sample-deep FIFO is
used on the Tx and Rx paths to absorb any phase difference between the AD9865’s internal clocks and the externally supplied
clocks (TXCLK, RXCLK). The ADIO bus accepts input datawords into the transmit path when the TXEN pin is high, the
RXEN pin is low, and a clock is present on the TXCLK pin, as
shown in Figure 49.
tDS
appears on the bus after a 6-clock-cycle delay due to the internal
FIFO delay. Note that Rx data is not latched back into the Tx
path, if TXEN is high during this interval with TXCLK present.
The ADIO bus becomes three-stated once the RXEN pin returns
low. Figure 50 shows the receive path output timing.
RXCLK
RXEN
tPZL
tOD
tPLZ
tVT
ADIO[9:0]
RX0
RX1
RX2
RX3
4493-0-008
The digital interface port is configurable for half-duplex or fullduplex operation by pin-strapping the MODE pin low or high,
respectively. In half-duplex mode, the digital interface port
becomes a 10-bit bidirectional bus called the ADIO port. In
full-duplex mode, the digital interface port is divided into two
6-bit ports called Tx[5:0] and Rx[5:0] for simultaneous Tx and
Rx operations. In this mode, data is transferred between the
ASIC and AD9865 in 6-bit (or 5-bit) nibbles. The AD9865 also
features a flexible digital interface for updating the RxPGA and
TxPGA gain registers via a 6-bit PGA port or Tx[5:0] port for
fast updates, or via the SPI port for slower updates. See the
RxPGA Control section for more information.
Figure 50. Receive Data Output Timing Diagram
To add flexibility to the digital interface port, several programming options are available in the SPI registers. These options
are listed in Table 13. The default Tx and Rx data input formats
are straight binary, but can be changed to twos complement.
The default TXEN and RXEN settings are active high, but can
be set to opposite polarities, thus allowing them to share the
same control. In this case, the ADIO port can still be placed
onto a shared bus by disabling its input latch via the control
signal, and disabling the output driver via the SPI register. The
clock timing can be independently changed on the transmit and
receive paths by selecting either the rising or falling clock edge
as the validating/sampling edge of the clock. Lastly, the output
driver’s strength can be reduced for lower data rate applications.
Table 13. SPI Registers for Half-Duplex Interface
Address (Hex)
0x0C
0x0D
0x0E
Bit
(4)
(1)
(0)
(5)
(4)
(1)
(0)
(7)
Description
Invert TXEN
TXCLK negative edge
Twos complement
Rx port three-state
Invert RXEN
RXCLK negative edge
Twos complement
Low digital drive strength
TXCLK
ADIO[9:0]
tEN
TX0
tDIS
tDH
TX1
TX2
TX3
TX4
4493-0-007
TXEN
RXEN
Figure 49. Transmit Data Input Timing Diagram
The Tx interpolation filter(s) following the ADIO port can be
flushed with zeros, if the clock signal into the TXCLK pin is
present for 33 clock cycles after TXEN goes low. Note that the
data on the ADIO bus is irrelevant over this interval.
The output from the receive path is driven onto the ADIO bus
when the RXEN pin is high, and a clock is present on the RXCLK
pin. While the output latch is enabled by RXEN, valid data
The half-duplex interface can be configured to act as a slave or a
master to the digital ASIC. An example of a slave configuration
is shown in Figure 51. In this example, the AD9865 accepts all
the clock and control signals from the digital ASIC. Because the
sampling clocks for the DAC and ADC are derived internally
from the OSCIN signal, the TXCLK and RXCLK signals must
be at exactly the same frequency as the OSCIN signal. The
phase relationships among the TXCLK, RXCLK, and OSCIN
signals can be arbitrary. If the digital ASIC cannot provide a low
jitter clock source to OSCIN, use the AD9865 to generate the
clock for its DAC and ADC, and to pass the desired clock signal
to the digital ASIC via CLKOUT1 or CLKOUT2.
Rev. A | Page 23 of 48
AD9865
AD9865
10
ADIO
[9:0]
Tx/Rx
Data[9:0]
RXEN
RXEN
TXEN
TXEN
DAC_CLK
TXCLK
ADC_CLK
RXCLK
CLKOUT
OSCIN
TO
Tx DIGITAL
FILTER
FROM
Rx ADC
4493-0-009
10
than the nibble rate. Therefore, the 2× or 4× interpolation filter
must be used with a full-duplex interface.
Figure 51. Example of a Half-Duplex Digital Interface
with AD9865 Serving as the Slave
Figure 52 shows a half-duplex interface with the AD9865 acting
as the master, generating all the required clocks. CLKOUT1
provides a clock equal to the bus data rate that is fed to the
ASIC as well as back to the TXCLK and RXCLK inputs. This
interface has the advantage of reducing the digital ASIC’s pin
count by three. The ASIC needs only to generate a bus control
signal that controls the data flow on the bidirectional bus.
DIGITAL ASIC
AD9865
ADIO
[9:0]
Tx/Rx
Data[9:0]
10
10
TO
Tx DIGITAL
FILTER
The AD9865 acts as the master, providing RXCLK as an output
clock that is used for the timing of both the Tx[5:0] and Rx[5:0]
ports. RXCLK always runs at the nibble rate and can be inverted
or disabled via an SPI register. Because RXCLK is derived from
the clock synthesizer, it remains active, provided that this functional block remains powered on. A buffered version of the
signal appearing at OSCIN can also be directed to RXCLK by
setting Bit 2 of Register 0x05. This feature allows the AD9865 to
be completely powered down (including the clock synthesizer)
while serving as the master.
The Tx[5:0] port operates in the following manner with the SPI
register default settings. Two consecutive nibbles of the Tx data
are multiplexed together to form a 10-bit data-word in twos
complement format. The clock appearing on the RXCLK pin is
a buffered version of the internal clock used by the Tx[5:0]
port’s input latch with a frequency that is always twice the ADC
sample rate (2 × fADC). Data from the Tx[5:0] port is read on the
rising edge of this sampling clock, as illustrated in the timing
diagram shown in Figure 53. Note, TXQUIET must remain
high for the reconstructed Tx data to appear as an analog signal
at the output of the TxDAC or IAMP.
ttDS
SU
FROM
Rx ADC
RXCLK
RXEN
tDHtHD
TXSYNC
TXEN
BUS_CTR
TXCLK
RXCLK
CLKIN
Tx[5:0]
Tx0LSB
Tx1MSB
Tx1LSB
Tx2MSB
Tx3LSB
Tx
2 LSB
Tx3MSB
4493-0-011
DIGITAL ASIC
CLKOUT1
Figure 53. Tx[5:0] Port Full-Duplex Timing Diagram
FROM
CRYSTAL
OR MASTER CLK
4493-0-010
OSCIN
Figure 52. Example of a Half-Duplex Digital Interface
with AD9865 Serving as the Master
FULL-DUPLEX MODE
The full-duplex mode interface is selected when the MODE pin
is tied high. It can be used for full- or half-duplex applications.
The digital interface port is divided into two 6-bit ports called
Tx[5:0] and Rx[5:0], allowing simultaneous Tx and Rx operations for full-duplex applications. In half-duplex applications,
the Tx[5:0] port can also be used to provide a fast update of the
RxPGA (AD9875 backward-compatible) during an Rx operation. This feature is enabled by default and can be used to
reduce the required pin count of the ASIC (refer to RxPGA
Control section for details).
In either application, Tx and Rx data are transferred between
the ASIC and AD9865 in 6-bit (or 5-bit) nibbles at twice the
internal input/output word rates of the Tx interpolation filter
and ADC. Note that the TxDAC update rate must not be less
The TXSYNC signal is used to indicate to which word a nibble
belongs. While TXSYNC is low, the first nibble of every word is
read as the most significant nibble. The second nibble of that
same word is read on the following TXSYNC high level as the
least significant nibble. If TXSYNC is low for more than one
clock cycle, the last transmit data is read continuously until
TXSYNC is brought high for the second nibble of a new transmit word. This feature can be used to flush the interpolator
filters with zeros. Note that the GAIN signal must be kept low
during a Tx operation.
The Rx[5:0] port operates in the following manner with the SPI
register default settings. Two consecutive nibbles of the Rx data
are multiplexed together to form a 10-bit data-word in twos
complement format. The Rx data is valid on the rising edge of
RXCLK, as illustrated in the timing diagram shown in Figure 54.
The RXSYNC signal is used to indicate to which word a nibble
belongs. While RXSYNC is low, the first nibble of every word is
transmitted as the most significant nibble. The second nibble of
that same word is transmitted on the following RXSYNC high
level as the least significant nibble.
Rev. A | Page 24 of 48
AD9865
Rx1MSB
Rx1LSB
Rx2MSB
Rx3LSB
Rx3MSB
Figure 54. Full-Duplex Rx Port Timing
To add flexibility to the full-duplex digital interface port, several
programming options are available in the SPI registers. These
options are listed in Table 14. The timing for the Tx[5:0] and/or
Rx[5:0] ports can be independently changed by selecting either
the rising or falling clock edge as the sampling/validating edge
of the clock. Inverting RXCLK (via Bit 1 or Register 0x05)
affects both the Rx and Tx interface, because they both use
RXCLK.
Figure 55 shows a possible digital interface between an ASIC
and the AD9865. The AD9865 serves as the master generating
the required clocks for the ASIC. This interface requires that the
ASIC reserve 16 pins for the interface, assuming a 6-bit nibble
width and the use of the Tx port for RxPGA gain control. Note
that the ASIC pin allocation can be reduced by 3, if a 5-bit
nibble width is used and the gain (or gain strobe) of the RxPGA
is controlled via the SPI port.
OPTIONAL
Table 14. SPI Registers for Full-Duplex Interface
Address (Hex)
0x05
0x0B
0x0C
0x0D
0x0E
Bit
(2)
Description
OSCIN to RXCLK
(1)
(0)
(2)
(4)
(3)
(2)
(1)
(0)
(5)
(4)
(3)
(2)
(1)
(0)
(7)
Invert RXCLK
Disable RXCLK
Rx gain on Tx port
Invert TXSYNC
Tx 5/5 nibble
LS nibble first
TXCLK negative edge
Twos complement
Rx port three-state
Invert RXSYNC
Rx 5/5 nibble
LS nibble first
RXCLK negative edge
Twos complement
Low drive strength
AD9865/AD9866
DIGITAL ASIC
6
GAIN
Tx[5:0]
Tx Data[5:0]
Rx[5:0]
Rx Data[5:0]
RX_SYNC
RXSYNC
TX_SYNC
TXSYNC
10/12
10/12
TO
RxPGA
TO
Tx DIGITAL
FILTER
FROM
RxADC
RXCLK
CLKIN
CLKOUT1
CLKOUT2
OSCIN
FROM
CRYSTAL
OR MASTER CLK
4493-0-013
Rx0LSB
MUX
Rx[5:0]
4493-0-012
tDv
RXSYNC
For the AD9865, the most significant nibble defaults to 6 bits,
and the least significant nibble defaults to 4 bits. This can be
changed so that the least significant nibble and most significant
nibble have 5 bits each. To accomplish this, set the 5/5 nibble bit
in Register 0x0C and Register 0x0D and use data pins Tx[5:1]
and Rx[5:1].
DEMUX
tDH
RXCLK
Figure 55. Example of a Full-Duplex Digital Interface
with Optional RxPGA Gain Control via Tx[5:0]
The default Tx and Rx data input formats are twos complement,
but can be changed to straight binary. The default TXSYNC and
RXSYNC settings can be changed such that the first nibble of
the word appears while TXSYNC, RXSYNC, or both are high.
Also, the least significant nibble can be selected as the first
nibble of the word (LS nibble first). The output driver strength
can also be reduced for lower data rate applications.
RxPGA CONTROL
The AD9865 contains a digital PGA in the Rx path that is used
to extend the dynamic range. The RxPGA can be programmed
over −12 dB to +48 dB with 1 dB resolution using a 6-bit word,
and with a 0 dB setting corresponding to a 2 V p-p input signal.
The 6-bit word is fed into a LUT that is used to distribute the
desired gain over three amplification stages within the Rx path.
Upon power-up, the RxPGA gain register is set to its minimum
gain of −12 dB. The RxPGA gain mapping is shown in Figure 56.
Table 15 lists the SPI registers pertaining to the RxPGA.
Rev. A | Page 25 of 48
AD9865
48
tSU
42
RXCLK
36
tHD
Tx SYNC
30
Tx [5:0]
GAIN
18
12
4493-0-015
GAIN (dB)
24
GAIN
6
Figure 57. Updating RxPGA via Tx[5:0] in Full-Duplex Mode
0
–12
0
6
12
18
24
30
36
42
48
54
60
6-BIT DIGITAL WORD-DECIMAL EQUIVALENT
66
4493-0-014
–6
Figure 56. Digital Gain Mapping of RxPGA
Table 15. SPI Registers RxPGA Control
Address
(Hex)
0x09
0x0B
Bit
(6)
(5:0)
(6)
(5)
(3)
(2)
(1)
Description
Enable RxPGA update via SPI
RxPGA gain code
Select TxPGA via PGA[5:0]
Select RxPGA via PGA[5:0]
Enable software GAIN strobe – Full-duplex
Enable RxPGA update via Tx[5:0] – Full-duplex
3-bit RxPGA gain mapping – Half-duplex
The RxPGA gain register can be updated via the Tx[5:0] port,
the PGA[5:0] port, or the SPI port. The first two methods allow
fast updates of the RxPGA gain register and should be
considered for digital AGC functions requiring a fast closedloop response. The SPI port allows direct update and readback
of the RxPGA gain register via Register 0x09 with an update
rate limited to 1.6 MSPS (with SCLK = 32 MHz). Note that Bit 6
of Register 0x09 must be set for a read or write operation.
Updating the RxPGA via the Tx[5:0] port is an option only in
full-duplex mode1. In this case, a high level on the GAIN pin,2
with TXSYNC low, programs the PGA setting on either the
rising edge or falling edge of RXCLK, as shown in Figure 57.
The GAIN pin must be held high, TXSYNC must be held low,
and GAIN data must be stable for one or more clock cycles to
update the RxPGA gain setting.
A low level on the GAIN pin enables data to be fed to the digital
interpolation filter. This interface should be considered when
upgrading existing designs from the AD9875/AD9876 MxFE
products or half-duplex applications trying to minimize an
ASIC’s pin count.
Updating the RxPGA (or TxPGA) via the PGA[5:0] port is an
option for both the half-duplex3 and full-duplex interface. The
PGA port consists of an input buffer that passes the 6-bit data
appearing at its input directly to the RxPGA (or TxPGA) gain
register with no gating signal required. Bit 5 or Bit 6 of
Register 0x0B is used to select whether the data updates the
RxPGA or TxPGA gain register. In applications that switch
between RxPGA and TxPGA gain control via PGA[5:0], be
careful that the RxPGA (or TxPGA) is not inadvertently loaded
with the wrong data during a transition. In the case of an
RxPGA to TxPGA transition, first deselect the RxPGA gain
register, update the PGA[5:0] port with the desired TxPGA gain
setting, and then select the TxPGA gain register.
The RxPGA also offers an alternative 3-bit word gain mapping
option4 that provides a −12 dB to +36 dB span in 8 dB increments
as shown in Table 16. The 3-bit word is directed to PGA[5:3]
with PGA[5] being the MSB. This feature is backward-compatible
with the AD9975 MxFE and allows direct interfacing to the
CX11647 or INT5130 HomePlug 1.0 PHYs.
Table 16. PGA Timing for AD9975 Backward-Compatible
Mode
Digital Gain Setting
PGA[5:3]
000
001
010
011
100
101
110
111
1
Decimal
0
1
2
3
4
5
6
7
Gain (dB)
−12
−12
−4
4
12
20
28
36
Default setting for full-duplex mode (MODE = 1).
The GAIN strobe can also be set in software via Reg. 0x0B, Bit 3 for
continuous updating. This eliminates the requirement for external GAIN
signal, reducing the ASIC pin count by 1.
3
Default setting for half-duplex mode (MODE = 0).
4
Default setting for MODE = 0 and CONFIG =1.
2
Rev. A | Page 26 of 48
AD9865
TXPGA CONTROL
0
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
–11
–12
–13
–14
–15
–16
–17
–18
–19
–20
Table 17 lists the SPI registers pertaining to the TxPGA. The
TxPGA control register default setting is for minimum
attenuation (0 dBFS) with the PGA[5:0] port disabled for Tx
gain control.
Table 17. SPI Registers TxPGA Control
Address (Hex)
0x0A
TxDACs IOUTP OUTPUT
HAS 7.5dB RANGE
0x0B
IAMPs IOUTN AND IOUTG
OUTPUTS HAS 19.5dB RANGE
0
8
16
24
32
40
04493-0-063
Tx ATTENUATION (dBFS)
The AD9865 also contains a digital PGA in the Tx path distributed between the TxDAC and IAMP. The TxPGA is used to
control the peak current from the TxDAC and IAMP over a
7.5 dB and 19.5 dB span, respectively, with 0.5 dB resolution.
A 6-bit word is used to set the TxPGA attenuation according to
the mapping shown in Figure 58. The TxDAC gain mapping is
applicable only when Bit 0 of Register 0x0E is set, and only the
four LSBs of the 6-bit gain word are relevant.
The TxPGA register can be updated via the PGA[5:0] port or
SPI port. The first method should be considered for fast updates
of the TxPGA register. Its operation is similar to the description
in the RxPGA Control section. The SPI port allows direct update and readback of the TxPGA register via Register 0x0A with
an update rate limited to 1.6 MSPS (SCLK = 32 MHz). Bit 6 of
Register 0x0A must be set for a read or write operation.
48
56
0x0E
64
6-BIT DIGITAL CODE (Decimal Equivalent)
Figure 58. Digital Gain Mapping of TxPGA
Rev. A | Page 27 of 48
Bit
(6)
(5:0)
(6)
(5)
(0)
Description
Enable TxPGA update via SPI
TxPGA gain code
Select TxPGA via PGA[5:0]
Select RxPGA via PGA[5:0]
TxDAC output (IAMP disabled)
AD9865
TRANSMIT PATH
0 TO –12dB
AD9865/AD9866
4493-0-017
TXEN/SYNC
TXCLK
2.0
–10
1.5
–20
1.0
0.5
–30
PASS BAND
–40
–50
–60
–1.0
–70
–1.5
–80
–2.0
0
DIGITAL INTERPOLATION FILTERS
Table 18. Interpolation Factor Set via SPI Register 0x0C
0.25
0.50
0.75
1.00
1.25
1.75
1.50
NORMALIZED FREQUENCY (Relative to fDATA)
–2.5
2.00
Figure 60. Frequency Response of 2× Interpolation Filter
(Normalized to fDATA)
2.5
10
WIDE BAND
WIDE BAND RESPONSE (dB)
The input data from the Tx port can be fed into a selectable
2×/4× interpolation filter or directly into the TxDAC (for a halfduplex only). The interpolation factor for the digital filter is set
via SPI Register 0x0C with the settings shown in Table 18. The
maximum input word rate, fDATA, into the interpolation filter is
80 MSPS; the maximum DAC update rate is 200 MSPS. Therefore, applications with input word rates at or below 50 MSPS
can benefit from 4× interpolation, while applications with input
word rates between 50 MSPS and 80 MSPS can benefit from
2× interpolation.
–0.5
–1.0dB @ 0.441 fDATA
–90
Figure 59. Functional Block Diagram of Tx Path
Bits [7:6]
00
01
10
11
0
PASS BAND RESPONSE (dB)
0 TO –7.5dB
IAMP
0
4493-0-018
TxDAC
WIDE BAND
Interpolation Factor
4
2
1 (half-duplex only)
Do not use
0
2.0
–10
1.5
–20
1.0
0.5
–30
PASS BAND
0
–40
–1.0dB @ 0.45 fDATA
–50
–0.5
–60
–1.0
–70
–1.5
–80
–2.0
–90
0
0.5
1.0
1.5
2.0
2.5
3.5
3.0
NORMALIZED FREQUENCY (Relative to fDATA)
–2.5
4.0
PASS BAND RESPONSE (dB)
2-4X
IOUT_G+
IOUT_N+
IOUT_N–
IOUT_G–
2.5
10
4493-0-019
ADIO[11:6]/
Rx[5:0]
10
The pipeline delays of the 2× and 4× filter responses are 21.5
and 24 clock cycles, respectively, relative to fDATA. The filter delay
is also taken into consideration for applications configured for a
half-duplex interface with the half-duplex power-down mode
enabled. This feature allows the user to set a programmable
delay that powers down the TxDAC and IAMP only after the
last Tx input sample has propagated through the digital filter.
See the Power Control and Dissipation section for more details.
WIDE BAND RESPONSE (dB)
ADIO[11:6]/
Tx[5:0]
IOUT_P–
IOUT_P+
The AD9865 (or AD9866) transmit path consists of a selectable
digital 2×/4× interpolation filter, a 10-bit or 12-bit TxDAC, and
a current-output amplifier (IAMP) as shown in Figure 59. Note
that the additional two bits of resolution offered by the AD9866
result in a 10 dB to 12 dB reduction in the pass-band noise
floor. The digital interpolation filter relaxes the Tx analog
filtering requirements by simultaneously reducing the images
from the DAC reconstruction process while increasing the
analog filter’s transition band. The digital interpolation filter
can also be bypassed, resulting in lower digital current
consumption.
Figure 61. Frequency Response of 4× Interpolation Filter
(Normalized to fDATA)
The interpolation filter consists of two cascaded half-band filter
stages with each stage providing 2× interpolation. The first
stage filter consists of 43 taps. The second stage filter, operating
at the higher data rate, consists of 11 taps. The normalized
wideband and pass-band filter responses (relative fDATA) for the
2× and 4× low-pass interpolation filters are shown in Figure 60
and Figure 61, respectively. These responses also include the
inherent sinc(x) from the TxDAC reconstruction process and
can be used to estimate any post analog filtering requirements.
TxDAC AND IAMP ARCHITECTURE
The Tx path contains a TxDAC with a current amplifier, IAMP.
The TxDAC reconstructs the output of the interpolation filter
and sources a differential current output that can be directed to
an external load or fed into the IAMP for further amplification.
The TxDAC’s and IAMPS’s peak current outputs are digitally
programmable over a 0 to −7.5 dB and 0 to −19.5 dB range,
respectively, in 0.5 dB increments. Note that this assumes
default register settings for Register 0x10 and Register 0x11.
Rev. A | Page 28 of 48
AD9865
Applications demanding the highest spectral performance
and/or lowest power consumption can use the TxDAC output
directly. The TxDAC is capable of delivering a peak signal
power-up to 10 dBm while maintaining respectable linearity
performance, as shown in Figure 27 through Figure 38. For
power-sensitive applications requiring the highest Tx power
efficiency, the TxDAC’s full-scale current output can be reduced
to as low as 2 mA, and its load resistors sized to provide a
suitable voltage swing that can be amplified by a low-power opamp-based driver.
Most applications requiring higher peak signal powers (up to
23 dBm) should consider using the IAMP. The IAMP can be
configured as a current source for loads having a well defined
impedance (50 Ω or 75 Ω systems), or a voltage source (with the
addition of a pair of npn transistors) for poorly defined loads
having varying impedance (such as power lines).
IOFF2
IOFF2
xN
xG
IOUTG–
G × (I–∆I)
G × (I+∆I)
IOUTG+
I
IOUTN–
REFADJ
±∆IS
IOUTN+
TxDAC
I
N × (I–∆I)
N × (I+∆I)
Figure 62 shows the equivalent schematic of the TxDAC and
IAMP. The TxDAC provides a differential current output
appearing at IOUTP+ and IOUTP−. It can be modeled as a
differential current source generating a signal-dependent ac
current, when ∆IS has a peak current of I along with two dc
current sources, sourcing a standing current equal to I. The fullscale output current, IOUTFS, is equal to the sum of these
standing current sources (IOUTFS = 2 × I).
REFIO
RSET 0.1µF
IOUTP+
I – ∆I
IOUTP–
IOFF1
IOFF1
xN
xG
4493-0-020
I + ∆I
IAMP
clearing Bit 0 of Register 0x0E. As a result, the IOUTP pins
must remain completely open, if the IAMP is to be used. The
IAMP contains two sets of current mirrors that are used to
replicate the TxDAC’s current output with a selectable gain. The
first set of current mirrors is designated as the primary path,
providing a gain factor of N that is programmable from 0 to 4 in
steps of 1 via Bits 2:0 of Register 0x10 with a default setting of
N = 4. Bit 7 of this register must be set to overwrite the default
settings of this register. This differential path exhibits the best
linearity performance (see Figure 42) and is available at the
IOUTN+ and IOUTN− pins. The maximum peak current per
output is 100 mA and occurs when the TxDAC’s standing
current, I, is set for 12.5 mA (IOUTFS = 25 mA).
The second set of current mirrors is designated as the secondary path providing a gain factor of G that is programmable
from 0 to 36 via Bits 6:4 of Register 0x10 and Bits 6:0 of Register
0x11 with a default setting of G = 12. This differential path is
intended to be used in the voltage mode configuration to bias
the external npn transistors, because it exhibits degraded
linearity performance (see Figure 43) relative to the primary
path. It is capable of sinking up to 180 mA of peak current into
either its IOUTG+ or IOUTG− pins. The secondary path
actually consists of three gain stages (G1, G2, and G3), which
are individually programmable as shown in Table 19. While
many permutations may exist to provide a fixed gain of G, the
linearity performance of a secondary path remains relatively
independent of the various individual gain settings that are
possible to achieve a particular overall gain factor.
Both sets of mirrors sink current, because they originate from
NMOS devices. Therefore, each output pin requires a dc current
path to a positive supply. Although the voltage output of each
output pin can swing between 0.5 V and 7 V, optimum ac performance is typically achieved by limiting the ac voltage swing
with a dc bias voltage set between 4 to 5 V. Lastly, both the
standing current, I, and the ac current, ∆IS, from the TxDAC are
amplified by the gain factor (N and G) with the total standing
current drawn from the positive supply being equal to
2 × (N = G) × I
Figure 62. Equivalent Schematic of TxDAC and IAMP
The value of I is determined by the RSET value at the REFADJ
pin along with the Tx path’s digital attenuation setting. With
0 dB attenuation, the value of I is
I = 16 × (1.23/RSET)
(1)
For example, an RSET value of 1.96 kΩ results in I equal to
10.0 mA with IOUTFS equal to 20.0 mA. Note that the REFIO
pin provides a nominal band gap reference voltage of 1.23 V
and should be decoupled to analog ground via a 0.1 µF
capacitor.
The differential current output of the TxDAC is always connected to the IOUTP pins, but can be directed to the IAMP by
Programmable current sources IOFF1 and IOFF2 via Register 0x12
can be used to improve the primary and secondary path
mirrors’ linearity performance under certain conditions by
increasing their signal-to-standing current ratio. This feature
provides a marginal improvement in distortion performance
under large signal conditions when the peak ac current of the
reconstructed waveform frequently approaches the dc standing
current within the TxDAC (0 to −1 dBFS sine wave) causing the
internal mirrors to turn off. However, the improvement in
distortion performance diminishes as the crest factor (peak-torms ratio) of the ac signal increases. Most applications can
disable these current sources (set to 0 mA via Register 0x12) to
reduce the IAMP’s current consumption.
Rev. A | Page 29 of 48
AD9865
1:1
Table 19. SPI Registers for TxDAC and IAMP
0x11
(7)
(6:4)
(3)
(2:0)
0x12
(6:4)
(2:0)
Tx PROGRAMMABLE GAIN CONTROL
TxPGA functionality is also available to set the peak output
current from the TxDAC or IAMP. The TxDAC and IAMP are
digitally programmable via the PGA[5:0] port or SPI over a 0 dB
to −7.5 dB and 0 dB to −19.5 dB range, respectively, in 0.5 dB
increments.
The TxPGA can be considered as two cascaded attenuators with
the TxDAC providing 7.5 dB range in 0.5 dB increments, and
the IAMP providing 12 dB range in 6 dB increments. As a
result, the IAMP’s composite 19.5 dB span is valid only if
Register 0x10 remains at its default setting of 0x44. Modifying
this register setting corrupts the LUT and results in an invalid
gain mapping.
TxDAC OUTPUT OPERATION
The differential current output of the TxDAC is available at the
IOUTP+ and IOUTP− pins and the IAMP should be disabled
by setting Bit 0 of Register 0x0E. Any load connected to these
pins must be ground referenced to provide a dc path for the
current sources. Figure 63 shows the outputs of the TxDAC
driving a doubly terminated 1:1 transformer with its center-tap
tied to ground. The peak-to-peak voltage, V p-p, across RL (and
IOUT+ to IOUT−) is equal to 2 × I × (RL//RS). With I = 10 mA
and RL = RS = 50 Ω, V p-p is equal to 0.5 V with 1 dBm of peak
power being delivered to RL and 1 dBm being dissipated in RS.
RL
RS
0.1µF
TxDAC
0 TO –7.5dB
IOUT_P–
IOUT_P+
RSET
IOUTN+
IOUTG+
IAMP
0 TO –12dB
IOUTN–
IOUTG–
4493-0-021
(3)
(2:0)
Description
TxDAC output
Enable current mirror gain settings
Secondary path first stage gain of 0
to 4 with ∆ = 1
Not used
Primary path NMOS gain of 0 to 4
with ∆ = 1
Don’t care
Secondary path second stage gain of
0 to 1.5 with ∆ = 0.25
Not used
Secondary path third stage gain of 0
to 5 with ∆ = 1
IOFF2, secondary path standing
current
IOFF1, primary path standing current
REFIO
Bit
(0)
(7)
(6:4)
REFADJ
Address (Hex)
0x0E
0x10
Figure 63. TxDAC Output Directly via Center-Tap Transformer
The TxDAC is capable of delivering up to 10 dBm peak power
to a load, RL. To increase the peak power for a fixed standing
current, one must increase V p-p across IOUTP+ and IOUTP−
by increasing one or more of the following parameters: RS, RL (if
possible), and/or the turns ratio, N, of transformer. For example, the removal of RS and the use of a 2:1 impedance ratio
transformer in the previous example results in 10 dBm of peak
power capabilities to the load. Note that increasing the power
output capabilities of the TxDAC reduces the distortion performance due to the higher voltage swings seen at IOUTP+ and
IOUTP−. See Figure 27 through Figure 38 for performance
plots on the TxDAC’s ac performance. Optimum distortion
performance can typically be achieved by:
•
Limiting the peak positive VIOUTP+ and VIOUTP− to 0.8 V to
avoid onset of TxDAC’s output compression. (TxDAC’s
voltage compliance is around 1.2 V.)
•
Limiting V p-p seen at IOUTP+ and IOUTP− to less
than 1.6 V.
Applications demanding higher output voltage swings and
power drive capabilities can benefit from using the IAMP.
IAMP CURRENT-MODE OPERATION
The IAMP can be configured for the current-mode operation as
shown in Figure 64 for loads remaining relatively constant. In
this mode, the primary path mirrors should be used to deliver
the signal-dependent current to the load via a center-tapped
transformer, because it provides the best linearity performance.
Because the mirrors exhibit a high output impedance, they can
be easily back-terminated (if required).
For peak signal currents (IOUTPK up to 50 mA), only the
primary path mirror gain should be used for optimum
distortion performance and power efficiency. The primary
path’s gain should be set to 4, with the secondary path’s gain
stages set to 0 (Register 0x10 = 0x84). The TxDAC’s standing
current, I, can be set between 2.5 mA and 12.5 mA with the
IOUTP outputs left open. The IOUTN outputs should be
connected to the transformer, with the IOUTG (and IOUTP)
Rev. A | Page 30 of 48
AD9865
outputs left open for optimum linearity performance. The
transformer1 should be specified to handle the dc standing
current, IBIAS, drawn by the IAMP. Also, because IBIAS remains
signal independent, a series resistor (not shown) can be inserted
between AVDD and the transformer’s center-tap to reduce the
IAMP’s common-mode voltage, VCM, and reduce the power
dissipation on the IC. The VCM bias should not exceed 5.0 V and
the power dissipated in the IAMP alone is as follows:
PIAMP = 2 × (N + G) × I × VCM
AVDD
0.1µF
IOUT_P–
IOUTN+
IBIAS = 2 × (N+G) × 1
0.1µF
RSET
IOUTG+
AVDD
IOUTN–
IOUT_P+
RL
TxDAC
4493-0-022
IOUTG–
IOUTPK = (N+G) × 1
P_OUTPK = (IOUTPK)2 × T2 × RL
IOUTN+
DUAL NPN
PHILLIPS PBR951
RS 0.1µF
IOUTG+
IOUTPK
IAMP
0 TO –7.5dB
R
0 TO –12dB
AVDD
TO LOAD
IOUTN–
IOUTG–
4493-0-023
0 TO –12dB
IOUTPK
R
IOUT_P–
IAMP
REFIO
T:1
TxDAC
0 TO –7.5dB
The voltage-mode configuration is shown in Figure 65. This
configuration is suited for applications having a poorly defined
load that can vary over a considerable range. A low impedance
voltage driver can be realized with the addition of two external
RF bipolar npn transistors (Phillips PBR951) and resistors. In
this configuration, the current mirrors in the primary path
(IOUTN outputs) feed into scaling resistors, R, generating a
differential voltage into the bases of the npn transistors. These
transistors are configured as source followers with the secondary path current mirrors appearing at IOUTG+ and IOUTG−
providing a signal-dependent bias current. Note that the
IOUTP outputs must remain open for proper operation.
REFADJ
IOUT_P+
RSET
REFADJ
REFIO
0.1µF
(2)
IAMP VOLTAGE-MODE OPERATION
RS 0.1µF
Figure 64. Current-Mode Operation
A step-down transformer1 with a turn ratio, T, can be used to
increase the output power, P_OUT, delivered to the load. This
causes the output load, RL, to be reflected back to the IAMP’s
differential output by T2, resulting in a larger differential voltage
swing seen at the IAMP’s output. For example, the IAMP can
deliver 24 dBm of peak power to a 50 Ω load, if a 1.41:1 stepdown transformer is used. This results in 5 V p-p voltage swings
appearing at IOUTN+ and IOUTN− pins. Figure 42 shows how
the third order intercept point, OIP3, of the IAMP varies as a
function of common-mode voltage over a 2.5 MHz to 20.0 MHz
span with a 2-tone signal having a peak power of approximately
24 dBm with IOUTPK = 50 mA.
For applications requiring an IOUTPK exceeding 50 mA, set the
secondary’s path to deliver the additional current to the load.
IOUTG+ and IOUTN+ should be shorted as well as IOUTG−
and IOUTN−. If IOUTPK represents the peak current to be
delivered to the load, then the current gain in the secondary
path, G, can be set by the following equation:
G = IOUTPK/12.5 − 4
(3)
The linearity performance becomes limited by the secondary
mirror path’s distortion.
1
The B6080 and BX6090 transformers from Pulse Engineering are worthy of
consideration for current and voltage modes.
Figure 65. Voltage-Mode Operation
The peak differential voltage signal developed across the npn’s
bases is as follows:
VOUTPK = R × (N × I)
(4)
where:
N is the gain setting of the primary mirror.
I is the standing current of the TxDAC defined in Equation 1.
The common-mode bias voltage seen at IOUTN+ and IOUTN−
is approximately AVDD − VOUTPK, while the common-mode
voltage seen at IOUTG+ and IOUTG− is approximately the
npn’s VBE drop below this level (AVDD − VOUTPK − 0.65). In
the voltage-mode configuration, the total power dissipated
within the IAMP is as follows :
PIAMP = 2 × I × {(AVDD − VOUTPK) × N
+ (AVDD − VOUTPK − 0.65) × G}
(5)
The emitters of the npn transistors are ac-coupled to the transformer1 via a 0.1 µF blocking capacitor and series resistor of 1 Ω
to 2 Ω. Note that protection diodes are not shown for clarity
purposes, but should be considered if interfacing to a power or
phone line.
The amount of standing and signal-dependent current used to
bias the npn transistors depends on the peak current, IOUTPK,
required by the load. If the load is variable, determine the worst
case, IOUTPK, and add 3 mA of margin to ensure that the npn
transistors remain in the active region during peak load
Rev. A | Page 31 of 48
AD9865
currents. The gain of the secondary path, G, and the TxDAC’s
standing current, I, can be set using the following equation:
90
(6)
80
70
The Tx path’s analog current consumption is an important
consideration when determining its contribution to the overall
on-chip power dissipation. This is especially the case in fullduplex applications, where the power dissipation can exceed the
maximum limit of 1.66 W, if the IAMP’s IOUTPK is set to high.
The analog current consumption includes the TxDAC’s analog
supply (Pin 43) along with the standing current from the IAMP’s
outputs. Equation 2 and Equation 5 can be used to calculate the
power dissipated in the IAMP for the current and voltage mode
configuration. Figure 66 shows the current consumption for the
TxDAC and IAMP as a function of the TxDAC’s standing current,
I, when only the IOUTN outputs are used. Figure 67 shows the
current consumption for the TxDAC and IAMP as a function of
the TxDAC’s standing current, I, when the IOUTN and IOUTG
outputs are used. Both figures are with the default current mirror
gain settings of N = 4 and G = 12.
60
IAMPN OUTPUT
50
40
TxDACs AVDD
04493-0-064
30
20
10
1
2
3
4
5
6
7
8
9
10
11
12
13
I (mA)
Figure 66. Current Consumption of TxDAC and IAMP in Current-Mode
Operation with IOUTN Only (Default IAMP Settings)
150
140
130
IOUTG OUTPUT
120
110
ISUPPLY (mA)
IAMP CURRENT CONSUMPTION CONSIDERATIONS
ISUPPLY (mA)
The voltage output driver exhibits a high output impedance if
the bias currents for the npn transistors are removed. This
feature is advantageous in half-duplex applications (for
example, power lines) in which the Tx output driver must go
into a high impedance state while in Rx mode. If the AD9865 is
configured for the half-duplex mode (MODE = 0), the IAMP,
TxDAC, and interpolation filter are automatically powered
down after a Tx burst (via TXEN), thus placing the Tx driver
into a high impedance state while reducing its power
consumption.
100
90
80
70
60
50
TxDAC AVDD
40
30
IOUTN OUTPUT
20
10
1.0
04493-0-065
IOUTPK + 3 mA = G × I
100
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
I (mA)
Figure 67. Current Consumption of TxDAC and IAMP in Current-Mode
Operation with IOUTN Only (Default IAMP Settings)
Rev. A | Page 32 of 48
AD9865
RECEIVE PATH
does not get amplified with high RxPGA gain settings,
potentially exceeding the ADC input range.
The receive path block diagram for the AD9865 (or AD9866) is
shown in Figure 68. The receive signal path consists of a 3-stage
RxPGA, a 3-pole programmable LPF, and a 10-bit (or 12-bit)
ADC. Note that the additional two bits of resolution offered by
the AD9866 result in a 3 dB to 5 dB lower noise floor depending
on the RxPGA gain setting and LPF cutoff frequency. Also working
in conjunction with the receive path is an offset correction circuit.
These blocks are discussed in detail in the following sections.
Note that the power consumption of the RxPGA can be modified
via Register 0x13 as discussed in the Power Control and
Dissipation section.
2M CLK
MULTIPLIER
ADIO[11:6]/
Rx[5:0]
OSCIN
XTAL
10/12
RXEN/SYNC
RXCLK
ADC
80MSPS
SPGA
RX+
2-POLE
LPF
1-POLE
LPF
RX–
0 TO 6dB –6 TO 18dB –6 TO 24dB
∆ = 1dB ∆ = 6dB
∆ = 6dB
4
SPORT
GAIN
MAPPING
LUT
6
REGISTER
CONTROL
4493-0-024
PGA[5:0]
AD9865/AD9866
Figure 68. Functional Block Diagram of Rx Path
RX PROGRAMMABLE GAIN AMPLIFIER
The RxPGA has a digitally programmable gain range from
−12 dB to +48 dB with 1 dB resolution via a 6-bit word. Its
purpose is to extend the dynamic range of the Rx path such that
the input of the ADC is presented with a signal that scales
within its fixed 2 V input span. There are multiple ways of
setting the RxPGA’s gain as discussed in the RxPGA Control
section, as well as an alternative 3-bit gain mapping having a
range of −12 dB to +36 dB with 8 dB resolution.
The RxPGA is comprised of two sections: a continuous time
PGA (CPGA) for course gain and a switched capacitor PGA
(SPGA) for fine gain resolution. The CPGA consists of two
cascaded gain stages providing a gain range from −12 dB to
+42 dB with 6 dB resolution. The first stage features a low noise
preamplifier (< 3.0 nV/rtHz), thereby eliminating the need for
an external preamplifier. The SPGA provides a gain range from
0 dB to 6 dB with 1 dB resolution. A look-up table (LUT) is
used to select the appropriate gain setting for each stage.
The gain of the RxPGA should be set to minimize clipping of
the ADC while utilizing most of its dynamic range. The maximum peak-to-peak differential voltage that does not result in
clipping of the ADC is shown in Figure 69. While the graph
suggests that maximum input signal for a gain setting of −12 dB
is 8.0 V p-p, the maximum input voltage into the PGA should
be limited to less than 6 V p-p to prevent turning on ESD protection diodes. For applications having higher maximum input
signals, consider adding an external resistive attenuator network.
While the input sensitivity of the Rx path is degraded by the
amount of attenuation on a dB-to-dB basis, the low noise
characteristics of the RxPGA provide some design margin such
that the external line noise remains the dominant source.
The nominal differential input impedance of the RxPGA input
appearing at the device RX+ and RX− input pins is 400 Ω//4 pF
(±20%) and remains relatively independent of gain setting. The
PGA input is self-biased at a 1.3 V common-mode level allowing
maximum input voltage swings of ±1.5 V at RX+ and RX−. AC
coupling the input signal to this stage via coupling capacitors
(0.1 µF) is recommended to ensure that any external dc offset
Rev. A | Page 33 of 48
8.0000
4.0000
2.0000
1.0000
0.5000
0.2500
0.1250
0.0625
0.0312
0.0156
0.0100
–12
04493-0-031
CLKOUT_1
CLKOUT_2
CLK
SYN.
FULL-SCALE PEAK-TO-PEAK INPUT SPAN (V)
ADIO[11:6]/
Tx[5:0]
To limit the RxPGA’s self-induced input offset, an offset
cancellation loop is included. This cancellation loop is automatically performed upon power-up and can also be initiated
via SPI. During calibration, the RxPGA’s first stage is internally
shorted, and each gain stage set to a high gain setting. A digital
servo loop slaves a calibration DAC, which forces the Rx input
offset to be within ±32 LSB for this particular high gain setting.
Although the offset varies for other gain settings, the offset is
typically limited to ±5% of the ADC’s 2 V input span. Note that
the offset cancellation circuitry is intended to reduce the voltage
offset attributed to only the RxPGA’s input stage, not any dc
offsets attributed to an external source.
–6
0
6
12
18
24
30
36
42
48
GAIN (dB)
Figure 69. Maximum Peak-to-Peak Input vs. RxPGA Gain Setting
that Does Not Result in ADC Clipping
AD9865
1.30
0.25
GAIN (dB)
The low-pass filter (LPF) provides a third order response with a
cutoff frequency that is typically programmable over a 15 MHz
to 35 MHz span. Figure 68 shows that the first real pole is implemented within the first CPGA gain stage, and the complex
pole pair is implemented in the second CPGA gain stage.
Capacitor arrays are used to vary the different R-C time constants within these two stages in a manner that changes the
cutoff frequency while preserving the normalized frequency
response. Because absolute resistor and capacitor values are
process-dependent, a calibration routine lasting less than 100 µs
automatically occurs each time the target cutoff frequency
register (Register 0x08) is updated, ensuring a repeatable cutoff
frequency from device to device.
NORMALIZED GAIN RESPONSE
–0.25
1.20
–0.50
1.15
–0.75
1.10
–1.00
1.05
–1.25
1.00
–1.50
0.95
–1.75
0.90
–2.00
0.85
0.80
–2.25
NORMALIZED GROUP DELAY
–2.50
0.75
0.70
–2.75
–3.00
NORMALIZED GROUP DELAY
TIME RESPONSE (GDT)
1.25
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.65
1.0
0.9
4493-0-026
LOW-PASS FILTER
NORMALIZED FREQUENCY
Figure 71. LPF’s Normalized Pass-Band Gain and Group Delay Responses
Although the default setting specifies that the LPF be active, it
can also be bypassed providing a nominal f−3 dB of 55 MHz.
Table 20 shows the SPI registers pertaining to the LPF.
Table 20. SPI Registers for Rx Low-Pass Filter
Bit
(0)
(7:0)
Description
Enable Rx LPF
Target value
3
FUNDAMENTAL (dB)
The normalized wideband gain response is shown in Figure 70.
The normalized pass-band gain and group delay responses are
shown in Figure 71. The normalized cutoff frequency, f−3 dB,
results in −3 dB attenuation. Also, the actual group delay time
(GDT) response can be calculated given a programmed cutoff
frequency using the following equation:
Actual GDT = Normalized GDT/(2.45 × f−3dB)
(7)
–3
–6
–9
–12
5
–15
0
–18
0
5
10
15
20
25
30
35
40
45
50
INPUT FREQUENCY (MHz)
–5
Figure 72. Effects of RxPGA Gain on LPF Frequency Response
(f−3 dB = 32 MHz (@ 0 dB and fADC = 80 MSPS)
–10
–15
–20
The following formula1 can be used to estimate f−3 dB for a
RxPGA gain setting of 0 dB:
–25
f−3dB_0dB = (128/target) × (fADC/80) ×(fADC/30 + 23.83) f
–30
–35
0
0.5
1.0
1.5
FREQUENCY
2.0
2.5
Figure 70. LPF’s Normalized Wideband Gain Response
3.0
4493-0-025
GAIN (dB)
–6dB GAIN
0dB GAIN
+6dB GAIN
+18dB GAIN
+30dB GAIN
+42dB GAIN
0
4493-0-027
Address (Hex)
0x07
0x08
The −3 dB cut-off frequency, f−3 dB, is programmable by writing
an 8-bit word, referred to as the target, to Register 0x08. The
cutoff frequency is a function of the ADC sample rate, fADC, and
to a lesser extent, the RxPGA gain setting (in dB). Figure 72
shows how the frequency response, f−3 dB, varies as a function of
the RxPGA gain setting.
(8)
Figure 73 compares the measured and calculated f−3 dB using this
formula.
1
Empirically derived for a f−3 dB range of 15 MHz to 35 MHz and fADC of 40 MSPS
to 80 MSPS with an RxPGA = 0 dB.
Rev. A | Page 34 of 48
AD9865
35
ANALOG-TO-DIGITAL CONVERTER (ADC)
33
The AD9865 features a 10-bit analog-to-digital converter
(ADC) capable of up to 80 MSPS. Referring to Figure 68, the
ADC is driven by the SPGA stage, which performs both the
sample-and-hold and the fine gain adjust functions. A buffer
amplifier (not shown) isolates the last CPGA gain stage from
the dynamic load presented by the SPGA stage. The full-scale
input span of the ADC is 2 V p-p, and depending on the PGA
gain setting, the full-scale input span into the SPGA is
adjustable from 1 V to 2 V in 1 dB increments.
FREQUENCY (MHz)
31
29
27
25
80 MSPS MEASURED
23
80 MSPS CALCULATED
21
19
50 MSPS MEASURED
50 MSPS CALCULATED
15
48
64
80
96 112 128
144
160
176
192
208
224
TARGET-DECIMAL EQUIVALENT
4493-0-028
17
Figure 73. Measured and Calculated f−3 dB vs. Target Value
for fADC = 50 MSPS and 80 MSPS
The following scaling factor can be applied to the previous
formula to compensate for the RxPGA gain setting on f−3 dB:
Scale Factor = 1 − (RxPGA in dB)/382
(9)
This scaling factor reduces the calculated f−3 dB as the RxPGA is
increased. Applications that need to maintain a minimum cutoff frequency, f−3 dB_MIN, for all RxPGA gain settings should first
determine the scaling factor for the highest RxPGA gain setting
to be used. Next, the f−3 dB_MIN should be divided by this scale
factor to normalize to the 0 dB RxPGA gain setting (f−3 dB_0 dB).
Equation 8 can then be used to calculate the target value.
The LPF frequency response shows a slight sensitivity to
temperature, as shown in Figure 74. Applications sensitive to
temperature drift can recalibrate the LPF by rewriting the target
value to Register 0x08.
35
FREQUENCY (MHz)
The ADC sampling clock path also includes a duty cycle
restorer circuit, which ensures that the ADC gets a near 50%
duty cycle clock even when presented with a clock source with
poor symmetry (35/65). This circuit should be enabled if the
ADC sampling clock is a buffered version of the reference signal
appearing at OSCIN (see the Clock Synthesizer section), and if
this reference signal is derived from an oscillator or crystal
whose specified symmetry cannot be guaranteed to be within
45/55 (or 55/45). This circuit can remain disabled if the ADC
sampling clock is derived from a divided down version of the
clock synthesizer’s VCO, because this clock is near 50%.
The ADC’s power consumption can be reduced by 25 mA, with
minimal effect on its performance, by setting Bit 4 of Register
0x07. Alternative power bias settings are also available via
Register 0x13, as discussed in the Power Control and
Dissipation section. Lastly, the ADC can be completely powered
down for half-duplex operation, further reducing the AD9865’s
peak power consumption.
30
FOUT ACTUAL 80MHz AND –40°C
FOUT ACTUAL 80MHz AND +25°C
25
A pipelined multistage ADC architecture is used to achieve high
sample rates while consuming low power. The ADC distributes
the conversion over several smaller A/D subblocks, refining the
conversion with progressively higher accuracy as it passes the
results from stage to stage on each clock edge. The ADC typically performs best when driven internally by a 50% duty cycle
clock. This is especially the case when operating the ADC at
high sample rate (55 MSPS to 80 MSPS) and/or lower internal
bias levels, which adversely affect interstage settling time
requirements.
FOUT ACTUAL 80MHz AND +85°C
15
96
112
128
144
160
176
192
208
TARGET-DECIMAL EQUIVALENT
224
240
4493-0-029
20
Figure 74. Temperature Drift of f−3 dB for fADC = 80 MSPS and RxPGA = 0 dB
Rev. A | Page 35 of 48
AD9865
Table 21. SPI Registers for Rx ADC
REFT
TO
ADCs
C1
0.1µF
C3
0.1µF
Address (Hex)
0x04
C2
10µF
0x07
0x13
C4
0.1µF
REFB
1.0V
Bit
(5)
(4)
(4)
(2:0)
Description
Duty cycle restore circuit
ADC clock from PLL
ADC low power mode
ADC power bias adjust
AGC TIMING CONSIDERATIONS
TOP
VIEW
C4
C2
04493-0-066
C3
C1
Figure 75. ADC Reference and Decoupling
The ADC has an internal voltage reference and reference amplifier as shown in Figure 75. The internal band gap reference
generates a stable 1 V reference level that is converted to a differential 1 V reference centered about mid-supply (AVDD/2).
The outputs of the differential reference amplifier are available
at the REFT and REFB pins and must be properly decoupled for
optimum performance. The REFT and REFB pins are conveniently situated at the corners of the CSP package such that C1
(0603 type) can be placed directly across its pins. C3 and C4 can
be placed underneath C1, and C2 (10 µF tantalum) can be
placed furthest from the package.
When implementing a digital AGC timing loop, it is important
to consider the Rx path latency and settling time of the Rx path
in response to a change in gain setting. Figure 21 and Figure 24
show the RxPGA’s settling response to a 60 dB and 5 dB change
in gain setting when using the Tx[5:0] or PGA[5:0] port. While
the RxPGA settling time may also show a slight dependency on
the LPF’s cut-off frequency, the ADC’s pipeline delay along with
the ADIO bus interface presents a more significant delay. The
amount of delay or latency is dependent on whether a half-or
full-duplex is selected. An impulse response at the RxPGA’s
input can be observed after 10.0 ADC clock cycles (1/fADC) in
the case of a half-duplex interface, and 10.5 ADC clock cycles in
the case of a full-duplex interface. This latency, along with the
RxPGA settling time, should be considered to ensure stability of
the AGC loop.
Rev. A | Page 36 of 48
AD9865
CLOCK SYNTHESIZER
(fDAC). The first option is the default setting and most desirable
if fOSCIN is equal to the ADC sample rate, fADC. This option
typically results in the best jitter/phase noise performance for
the ADC sampling clock. The second option is suitable in cases
where fOSCIN is a factor of 2 or 4 less than the fADC. In this case,
the divider ratio, N, is chosen such that the divided down VCO
output is equal to the ADC sample rate, as shown in the
following equation:
The AD9865 generates all its internal sampling clocks, as well as
two user-programmable clock outputs appearing at CLKOUT1
and CLKOUT2, from a single reference source as shown in
Figure 76. The reference source can be either a fundamental
frequency or an overtone quartz crystal connected between
OSCIN and XTAL with the parallel resonant load components
as specified by the crystal manufacturer. It can also be a TTLlevel clock applied to OSCIN with XTAL left unconnected.
fADC = fDAC/2N
The data rate, fDATA, for the Tx and Rx data paths must always be
equal. Therefore, the ADC’s sample rate, fADC, is always equal to
fDATA while the TxDAC update rate is a factor of 1, 2, or 4 of
fDATA, depending on the interpolation factor selected. The data
rate refers to the word rate and should not be confused with the
nibble rate in full-duplex interface.
TO ADC
TO TxDAC
C2
CLKOUT2
÷ 2L
04493-0-030
CLKOUT1
÷ 2R
Figure 76. Clock Oscillator and Synthesizer
Figure 77 shows the degradation in phase noise performance
imparted onto the ADC’s sampling clock for different VCO
output frequencies. In this case, a 25 MHz, 1 V p-p sine wave
was used to drive OSCIN, and the PLL’s M and N factors were
selected to provide an fADC of 50 MHz for VCO operating
frequencies of 50, 100, and 200 MHz. The RxPGA input was
driven with a near full-scale, 12.5 MHz input signal with a gain
setting of 0 dB. Operating the VCO at the highest possible
frequency results in the best narrow and wideband phase noise
characteristics. For comparison purposes, the clock source for
the ADC was taken directly from OSCIN when driven by a
50 MHz square wave.
0
The 2M CLK multiplier contains a PLL (with integrated loop
filter) and VCO capable of generating an output frequency that
is a multiple of 1, 2, 4, or 8 of its input reference frequency,
fOSCIN, appearing at OSCIN. The input frequency range of fOSCIN
is between 20 MHz and 80 MHz, while the VCO can operate
over a 40 MHz to 200 MHz span. For the best phase noise/jitter
characteristics, it is advisable to operate the VCO with a frequency between 100 MHz and 200 MHz. The VCO output
drives the TxDAC directly such that its update rate, fDAC, is
related to fOSCIN by the following equation:
DIRECT
VCO = 50MHz
VCO = 100MHz
VCO = 200MHz
–10
–20
–30
–40
–50
–60
–70
–80
–90
04493-0-067
C1
÷2N
2M CLK
MULTIPLIER
OSCIN
where N = 0, 1, or 2.
dBFS
XTAL
XTAL
(12)
–100
fDAC = 2M × fOSCIN
(10)
–110
2.5
M is the PLL’s multiplication factor set in Register 0x04. The
value of M is determined by the Tx path’s word rate, fDATA, and
digital interpolation factor, F, as shown in the following
equation:
M = log2 (F × fDATA/fOSCIN)
4.5
6.5
8.5
10.5
12.5
14.5
16.5
18.5
20.5
22.5
FREQUENCY (MHz)
where M = 0, 1, 2, or 3.
(11)
Note: if the reference frequency appearing at OSCIN is chosen
to be equal to the AD9865’s Tx and Rx path’s word rate, then M
is simply equal to log2(F).
The clock source for the ADC can be selected in Register 0x04
as a buffered version of the reference frequency appearing at
OSCIN (default setting) or a divided version of the VCO output
Figure 77. Comparison of Phase Noise Performance when ADC Clock Source
is Derived from Different VCO Output Frequencies
The CLK synthesizer also has two clock outputs appearing at
CLKOUT1 and CLKOUT2. They are programmable via
Register 0x06. Both outputs can be inverted or disabled. The
voltage levels appearing at these outputs are relative to DRVDD
and remain active during a hardware or software reset. Table 22
shows the SPI registers pertaining to the clock synthesizer.
CLKOUT1 is a divided version of the VCO output and can be
set to be a submultiple integer of fDAC (fDAC/2R, where R = 0, 1, 2,
or 3). Because this clock is actually derived from the same set of
dividers used within the PLL core, it is phase-locked to them
such that its phase relationship relative to the signal appearing
Rev. A | Page 37 of 48
AD9865
at OSCIN (or RXCLK) can be determined upon power up. Also,
this clock has near 50% duty cycle, because it is derived from
the VCO. As a result, CLKOUT1 should be selected before
CLKOUT2 as the primary source for system clock distribution.
CLKOUT2 is a divided version of the reference frequency, fOSCIN,
and can be set to be a submultiple integer of fOSCIN (fOSCIN/2L,
where L = 0, 1, or 2). With L set to 0, the output of CLKOUT2 is
a delayed version of the signal appearing at OSCIN, exhibiting
the same duty cycle characteristics. With L set to 1 or 2, the
output of CLKOUT2 is a divided version of the OSCIN signal,
exhibiting a near 50% duty cycle, but without having a deterministic phase relationship relative to CLKOUT1 (or RXCLK).
Table 22. SPI Registers for CLK Synthesizer
Address (Hex)
0x04
0x06
Rev. A | Page 38 of 48
Bit
(4)
(3:2)
(1:0)
(7:6)
(5)
(4)
(3:2)
(1)
(0)
Description
ADC CLK from PLL
PLL divide factor (P)
PLL multiplication factor (M)
CLKOUT2 divide number
CLKOUT2 invert
CLKOUT2 disable
CLKOUT1 divide number
CLKOUT1 invert
CLKOUT1 disable
AD9865
POWER CONTROL AND DISSIPATION
POWER-DOWN
HALF-DUPLEX POWER SAVINGS
The AD9865 provides the ability to control the power-on state
of various functional blocks. The state of the PWRDWN pin
along with the contents of Register 0x01 and Register 0x02
allow two user-defined power settings that are pin selectable.
The default settings1 are such that Register 0x01 has all blocks
powered on (all bits 0), while Register 0x02 has all blocks
powered down excluding the PLL such that the clock signal
remains available at CLKOUT1 and CLKOUT2. When the
PWRDWN pin is low, the functional blocks corresponding to
the bits in Register 0x01 are powered down. When the
PWRDWN is high, the functional blocks corresponding to the
bits in Register 0x02 are powered down. PWRDWN
immediately affects the designated functional blocks with
minimum digital delay.
Significant power savings can be realized in applications having
a half-duplex protocol allowing only the Rx or Tx path to be
operational at any instance. The power savings method depends
on whether the AD9865 is configured for a full- or half-duplex
interface. Functional blocks having fast power on/off times for
the Tx and Rx path are controlled by the following bits:
TxDAC/IAMP, TX Digital, ADC, and RxPGA.
Table 23. SPI Registers Associated with Power-Down and
Half-Duplex Power Savings
Address (Hex)
0x01
0x02
0x03
Bit
(7)
(6)
(5)
(4)
(3)
(2)
(1)
(0)
(7)
(6)
(5)
(4)
(3)
(2)
(1)
(0)
(7:3)
(2)
(1)
(0)
1
Description
PLL
TxDAC/IAMP
TX Digital
REF
ADC CML
ADC
PGA BIAS
RxPGA
PLL
TxDAC/IAMP
TX Digital
REF
ADC CML
ADC
PGA BIAS
RxPGA
Tx OFF Delay
Rx PWRDWN
via TXEN
Enable Tx
PWRDWN
Enable Rx
PWRDWN
Comments
PWRDWN = 0.
Default setting is all
functional blocks
powered on.
PWRDWN = 1.
Default setting is all
functional blocks
powered off
excluding PLL.
Half-duplex power
savings.
In the case of a full-duplex digital interface (MODE = 1), one
can set Register 0x01 to 0x60 and Register 0x02 to Register 0x05
(or vice versa) such that the AD9865’s Tx and Rx path are never
powered on simultaneously. The PWRDWN pin can then be
used to control which path is powered on, depending on the
burst type. During a Tx burst, the Rx path’s PGA and ADC
blocks can typically be powered down within 100 ns, while the
Tx paths DAC, IAMP, and digital filter blocks are powered up
within 0.5 µs. For an Rx burst, the Tx path’s can be powered
down within 100 ns, while the Rx circuitry is powered up
within 2 µs.
Setting the TXQUIET pin low allows it to be used with the fullduplex interface to quickly power down the IAMP and disable
the interpolation filter. This is meant to maintain backward
compatibility with the AD9875/AD9876 MxFEs with the exception that the TxDAC remains powered, if its IOUTP outputs are
used. In most applications, the interpolation filter needs to be
flushed with 0s before or after being powered down. This
ensures that upon power-up, the TxDAC (and IAMP) have a
negligible differential dc offset, thus preventing spectral splatter
due to an impulse transient.
Applications using a half-duplex interface (MODE = 0) can
benefit from an additional power savings feature made available
in Register 0x03. This register is effective only for a half-duplex
interface. Besides providing power savings for half-duplex
applications, this feature allows the AD9865 to be used in
applications that need only its Rx (or Tx) path functionality
through pin-strapping, making a serial port interface (SPI)
optional. This feature also allows the PWRDWN pin to retain
its default function as a master power control, as defined in
Table 10.
The default settings for Register 0x03 provide fast power control
of the functional blocks in the Tx and Rx signal paths (outlined
above) using the TXEN pin. The TxDAC still remains powered
on in this mode, while the IAMP is powered down. Significant
current savings are typically realized when the IAMP is
powered down.
With MODE = 1 and CONFIG =1, Reg. 0x02 default settings are with all blocks
powered off, with RXCLK providing a buffered version of the signal
appearing at OSCIN. This setting results in the lowest power consumption
upon power-up, while still allowing AD9865 to generate the system clock via
a crystal.
For a Tx burst, the falling edge of TXEN is used to generate an
internal delayed signal for powering down the Tx circuitry.
Upon receipt of this signal, power-down of the Tx circuitry
Rev. A | Page 39 of 48
AD9865
occurs within 100 ns. The user-programmable delay for the Tx
path power-down is meant to match the pipeline delay of the
last Tx burst sample such that power-down of the TxDAC and
IAMP does not impact its transmission. A 5-bit field in Register 0x03
sets the delay from 0 to 31 TXCLK clock cycles, with the default
being 31 (0.62 µs with fTXCLK = 50 MSPS). The digital interpolation
filter is automatically flushed with midscale samples prior to
power-down, if the clock signal into the TXCLK pin is present
for 33 additional clock cycles after TXEN returns low. For an Rx
burst, the rising edge of TXEN is used to generate an internal
signal (with no delay) that powers up the Tx circuitry within 0.5 µs.
50
IAVDDTxDAC (mA)
45
40
35
30
25
20
04493-0-068
The Rx path power-on/power-off can be controlled by either
TXEN or RXEN by setting Bit 2 of Register 0x03. In the default
setting, the falling edge of TXEN powers up the Rx circuitry
within 2 µs, while the rising edge of TXEN powers down the Rx
circuitry within 0.5 µs. If RXEN is selected as the control signal,
then its rising edge powers up the Rx circuitry and the falling
edge powers it down. To disable the fast power-down of the Tx
and/or Rx circuitry, set Bit 1 and/or Bit 0 to 0.
55
15
10
0
1
2
3
4
5
6
7
8
9
10
11
12
13
ISTANDING (mA)
Figure 78. Reduction in TxDAC’s Supply Current vs. Standing Current
65
60
4× INTERPOLATION
55
POWER REDUCTION OPTIONS
45
40
2× INTERPOLATION
35
30
1× (HALF-DUPLEX ONLY)
25
04493-0-069
The power consumption of the AD9865 can be significantly
reduced from its default setting by optimizing the power
consumption versus performance of the various functional
blocks in the Tx and Rx signal path. On the Tx path, minimum
power consumption is realized when the TxDAC output is used
directly and its standing current, I, is reduced to as low as 1 mA.
Although a slight degradation in THD performance results at
reduced standing currents, it often remains adequate for most
applications, because the op amp driver typically limits the
overall linearity performance of the Tx path. The load resistors
used at the TxDAC outputs (IOUTP+ and IOUTP−) can be
increased to generate an adequate differential voltage that can
be further amplified via a power efficient op-amp-based driver
solution. Figure 78 shows how the supply current for the
TxDAC (Pin 43) is reduced from 55 mA to 14 mA as the
standing current is reduced from 12.5mA to 1.25 mA. Further
Tx power savings can be achieved by bypassing or reducing the
interpolation factor of the digital filter as shown in Figure 79.
IDVDD (mA)
50
20
15
20
30
40
50
60
70
80
INPUT DATA RATE (MSPS)
Figure 79. Digital Supply Current Consumption vs. Input Data Rate
(DVDD = DRVDD =3.3 V and fOUT = fDATA/10)
Power consumption on the Rx path can be achieved by reducing the bias levels of the various amplifiers contained within the
RxPGA and ADC. As previously noted, the RxPGA consists of
two CPGA amplifiers and one SPGA amplifier. The bias levels
of each of these amplifiers along with the ADC can be controlled via Register 0x13, as shown in Table 24. The default
setting for 0x13 is 0x00.
Table 24. SPI Register for RxPGA and ADC Biasing
Address (Hex)
0x07
0x13
Rev. A | Page 40 of 48
Bit
(4)
(7:5)
(4:3)
(2:0)
Description
ADC low power
CPGA bias adjust
SPGA bias adjust
ADC power bias adjust
AD9865
210
Because the CPGA processes signals in the continuous time
domain, its performance vs. bias setting remains mostly
independent of the sample rate. Table 25 shows how the typical
current consumption seen at AVDD (Pins 35 and 40) varies as a
function of Bits (7:5), while the remaining bits are maintained at
their default settings of 0. Only four of the possible settings
result in any reduction in current consumption relative to the
default setting. Reducing the bias level typically results in a
degradation in the THD vs. frequency performance as shown in
Figure 80. This is due to a reduction of the amplifier’s unity gain
bandwidth, while the SNR performance remains relatively
unaffected.
205
200
IAVDD (mA)
01
170
20
30
40
–54
–56
–58
59
SNR-00
SNR-01
SNR-10
SNR-11
58
57
55
–66
52
60.0
–30
51
20
–50
45.0
–60
–65
THD_RxPGA = 36dB
010
011
–70
100
04493-0-091
–55
001
30
40
50
60
70
–74
80
Figure 82. SNR and THD Performance vs. fADC and SPGA Bias Setting with
RxPGA = 0 dB, fIN = 10 MHz, LPF set to 26 MHz, and AIN = −1 dBFS
47.5
40.0
000
–72
SAMPLE RATE (MSPS)
THD_RxPGA = 0dB
42.5
–70
–40
–45
50.0
–68
THD-00
THD-01
THD-10
THD-11
–35
THD (dBc)
SNR (dBFS)
52.5
–62
–64
–25
SNR_RxPGA = 0dB
–60
56
62.5
SNR_RxPGA = 36dB
80
60
53
55.0
70
61
–20
57.5
60
Figure 81. AVDD Current vs. SPGA Bias Setting and Sample Rate
54
65.0
50
ADC SAMPLE RATE (MSPS)
THD (dBc)
∆ mA
0
−27
−42
−51
−55
27
69
27
04493-0-070
11
175
04493-0-092
Bit 5
0
1
0
1
0
1
0
1
185
10
SNR (dBc)
Bit 6
0
0
1
1
0
0
1
1
00
190
180
Table 25. Analog Supply Current vs. CPGA Bias Settings at
fADC = 65 MSPS
Bit 7
0
0
0
0
1
1
1
1
195
CPGA BIAS SETTING-BITS (7:5)
Figure 80. THD vs. fIN Performance and RxPGA Bias Settings
(000,001,010,100 with RxPGA = 0 and +36 dB and AIN = −1 dBFS,
LPF set to 26 MHz, and fADC = 50 MSPS)
The SPGA is implemented as a switched capacitor amplifier;
therefore, its performance vs. bias level is mostly dependent on
the sample rate. Figure 81 shows how the typical current
consumption seen at AVDD (Pin 35 and Pin 40) varies as a
function of Bits (4:3) and sample rate, while the remaining bits
are maintained at the default setting of 0. Figure 82 shows how
the SNR and THD performance is affected for a 10 MHz sine
wave input as the ADC sample rate is swept from 20 MHz to 80
MHz. The SNR and THD performance remains relatively stable,
suggesting that the SPGA bias can often be reduced from its default setting without impacting the device’s overall performance.
The ADC is based on a pipeline architecture with each stage
consisting of a switched capacitor amplifier. Therefore, its performance vs. bias level is mostly dependent on the sample rate.
Figure 83 shows how the typical current consumption seen at
AVDD (Pins 35 and 40) varies as a function of Bits (2:0) and
sample rate, while the remaining bits are maintained at the
default setting of 0. Setting Bit 4 or Register 0x07 corresponds
to the 011 setting, and the settings of 101 and 111 result in
higher current consumption. Figure 84 shows how the SNR and
THD performance are affected for a 10 MHz sine wave input
for the lower power settings as the ADC sample rate is swept
from 20 MHz to 80 MHz.
Rev. A | Page 41 of 48
AD9865
specification is based on the 64-pin LFSCP having a thermal
resistance, θJA, of 24oC/W with its heat slug soldered. (The θJA is
30.8oC/W, if the heat slug remains unsoldered.) If a particular
application’s maximum ambient temperature, TA, falls below
85oC, the maximum allowable power dissipation can be determined by the following equation:
220
101 OR 111
210
200
000
190
IAVDD (mA)
001
180
010
170
PMAX = 1.66 + (85 − TA)/24
160
100
150
011
101
Assuming the IAMP’s common-mode bias voltage is operating
off the same analog supply as the AD9865, the following equation can be used to calculate the maximum total current
consumption, IMAX, of the IC:
04493-0-071
140
130
120
20
30
40
50
60
70
80
IMAX = (PMAX − PIAMP)/3.47
SAMPLE RATE (MSPS)
(14)
Figure 83. AVDD Current vs. ADC Bias Setting and Sample Rate
With an ambient temperature of up to 85°C, IMAX is 478 mA.
61
–54
60
–56
If the IAMP is operating off a different supply or in the voltage
mode configuration, first calculate the power dissipated in the
IAMP, PIAMP, using Equation 2 or Equation 5, and then
recalculate IMAX, using Equation 14.
–58
59
THD-000
THD-001
THD-010
THD-011
THD-100
THD-101
56
–60
–62
–64
–66
55
54
SNR-000
SNR-001
SNR-010
SNR-011
SNR-100
SNR-101
53
52
51
20
30
40
60
70
Figure 78, Figure 79, Figure 81, and Figure 83 can be used to
calculate the current consumption of the Rx and Tx paths for a
given setting.
–68
MODE SELECT UPON POWER-UP AND RESET
–70
The AD9865 power-up state is determined by the logic levels
appearing at the MODE and CONFIG pins. The MODE pin is
used to select a half- or full-duplex interface by pin strapping it
low or high, respectively. The CONFIG pin is used in conjunction with the MODE pin to determine the default settings for
the SPI registers as outlined in Table 10.
–72
50
THD (dBc)
57
–74
80
04493-0-092
58
SNR (dBc)
(13)
SAMPLE RATE (MSPS)
Figure 84. SNR and THD Performance vs. fADC and ADC Bias Setting with
RxPGA = 0 dB, fIN = 10 MHz, and AIN = −1 dBFS
A sine wave input is a standard and convenient method of
analyzing the performance of a system. However, the amount of
power reduction that is possible is application dependent, based
on the nature of the input waveform (such as frequency content,
peak-to-rms ratio), the minimum ADC sample, and the minimum acceptable level of performance. Thus, it is advisable that
power-sensitive applications optimize the power bias setting of
the Rx path using an input waveform that is representative of
the application.
POWER DISSIPATION
The power dissipation of the AD9865 can become quite high in
full-duplex applications in which the Tx and Rx paths are simultaneously operating with nominal power bias settings. In
fact, some applications that use the IAMP may need to either
reduce its peak power capabilities or reduce the power consumption of the Rx path, so that the device’s maximum
allowable power consumption, PMAX, is not exceeded.
PMAX is specified at 1.66 W to ensure that the die temperature
does not exceed 125oC at an ambient temperature of 85oC. This
The intent of these particular default settings is to allow some
applications to avoid using the SPI (disabled by pin-strapping
SEN high), thereby reducing implementation costs. For
example, setting MODE low and CONFIG high configures the
AD9865 to be backward compatible with the AD9975, while
setting MODE high and CONFIG low makes it backward
compatible with the AD9875. Other applications must use the
SPI to configure the device.
A hardware (RESET pin) or software (Bit 5 of Register 0x00)
reset can be used to place the AD9865 into a known state of
operation as determined by the state of the MODE and
CONFIG pins. A dc offset calibration and filter tuning routine
is also initiated upon a hardware reset, but not with a software
reset. Neither reset method flushes the digital interpolation
filters in the Tx path. Refer to the Half-Duplex Mode and FullDuplex Mode sections for information on flushing the digital
filters.
A hardware reset can be triggered by pulsing the RESET pin low
for a minimum of 50 ns. The SPI registers are instantly reset to
their default settings upon RESET going low, while the dc offset
Rev. A | Page 42 of 48
AD9865
calibration and filter tuning routine is initiated upon RESET
returning high. To ensure sufficient power-on time of the
various functional blocks, RESET returning high should occur
no less than 10 ms upon power-up. If a digital reset signal from
a microprocessor reset circuit (such as ADM1818) is not
available, a simple R-C network referenced to DVDD can be
used to hold RESET low for approximately 10 ms upon powerup.
ANALOG AND DIGITAL LOOP-BACK TEST MODES
The AD9865 features analog and digital loop-back capabilities
that can assist in system debug and final test. Analog loop-back
routes the digital output of the ADC back into the Tx data path
prior to the interpolation filters such that the Rx input signal
can be monitored at the output of the TxDAC or IAMP. As a
result, the analog loop-back feature can be used for a half- or
full-duplex interface, to allow testing of the functionality of the
entire IC (excluding the digital data interface).
waveform) into the Rx input, and monitor the quality of the
reconstructed output from the TxDAC or IAMP to ensure a
minimum level of performance. In this test, the user can
exercise the RxPGA as well as validate the attenuation characteristics of the RxLPF. Note that the RxPGA gain setting
should be selected such that the input does not result in clipping
of the ADC.
Digital loop-back can be used to test the full-duplex digital
interface of the AD9865. In this test, data appearing on the
Tx[5:0] port is routed back to the Rx[5:0] port, thereby
confirming proper bus operation. The Rx port can also be
three-stated for half- and full-duplex interfaces.
Table 26. SPI Registers for Test Modes
Address (Hex)
0x0D
For example, the user can configure the AD9865 with similar
settings as the target system, inject an input signal (sinusoidal
Rev. A | Page 43 of 48
Bit
(7)
(6)
(5)
Description
Analog loop-back
Digital loop-back
Rx port three-state
AD9865
PCB DESIGN CONSIDERATIONS
Although the AD9865 is a mixed-signal device, the part should
be treated as an analog component. The on-chip digital circuitry
has been specially designed to minimize the impact of its digital
switching noise on the MxFE’s analog performance.
To achieve the best performance, the power, grounding, and
layout recommendations in this section should be followed.
Assembly instructions for the micro-lead frame package can be
found in an application note from Amkor at:
http://www.amkor.com/products/notes_papers/MLF_AppNote
_0902.pdf.
COMPONENT PLACEMENT
If the three following guidelines of component placement are
followed, chances for getting the best performance from the
MxFE are greatly increased. First, manage the path of return
currents flowing in the ground plane so that high frequency
switching currents from the digital circuits do not flow on the
ground plane under the MxFE or analog circuits. Second, keep
noisy digital signal paths and sensitive receive signal paths as
short as possible. Third, keep digital (noise generating) and
analog (noise susceptible) circuits as far away from each other
as possible.
To best manage the return currents, pure digital circuits that
generate high switching currents should be closest to the power
supply entry. This keeps the highest frequency return current
paths short and prevents them from traveling over the sensitive
MxFE and analog portions of the ground plane. Also, these
circuits should be generously bypassed at each device, which
further reduces the high frequency ground currents. The MxFE
should be placed adjacent to the digital circuits, such that the
ground return currents from the digital sections do not flow in
the ground plane under the MxFE.
The AD9865 has several pins that are used to decouple sensitive
internal nodes. These pins are REFIO, REFB, and REFT. The
decoupling capacitors connected to these points should have
low ESR and ESL. These capacitors should be placed as close to
the MxFE as possible (see Figure 75) and be connected directly
to the analog ground plane. The resistor connected to the
REFADJ pin should also be placed close to the device and
connected directly to the analog ground plane.
POWER PLANES AND DECOUPLING
While the AD9865 evaluation board demonstrates a very good
power supply distribution and decoupling strategy, it can be
further simplified for many applications. The board has four
layers: two signal layers, one ground plane, and one power
plane. While the power plane on the evaluation board is split
into multiple analog and digital subsections, a permissible
alternative would be to have AVDD and CLKVDD share the
same analog 3.3 V power plane. A separate analog plane/supply
may be allocated to the IAMP, if its supply voltage differs from
the 3.3 V required by AVDD and CLKVDD. On the digital side,
DVDD and DRVDD can share the same 3.3 V digital power
plane. This digital power plane brings the current used to power
the digital portion of the MxFE and its output drivers. This
digital plane should be kept from going underneath the analog
components.
The analog and digital power planes allocated to the MxFE may
be fed from the same low noise voltage source; however, they
should be decoupled from each other to prevent the noise
generated in the digital portion of the MxFE from corrupting
the AVDD supply. This can be done by using ferrite beads between the voltage source and the respective analog and digital
power planes with a low ESR, bulk decoupling capacitor on the
MxFE side of the ferrite. Each of the MxFE’s supply pins
(AVDD, CLKVDD, DVDD, and DRVDD) should also have
dedicated low ESR, ESL decoupling capacitors. The decoupling
capacitors should be placed as close to the MxFE supply pins as
possible.
GROUND PLANES
The AD9865 evaluation board uses a single serrated ground
plane to help prevent any high frequency digital ground
currents from coupling over to the analog portion of the ground
plane. The digital currents affiliated with the high speed data
bus interface (Pin 1 to Pin 16) have the highest potential of
generating problematic high frequency noise. A ground
serration that contains these currents should reduce the effects
of this potential noise source.
The ground plane directly underneath the MxFE should be
continuous and uniform. The 64-lead LFCSP package is
designed to provide excellent thermal conductivity. This is
partly achieved by incorporating an exposed die paddle on the
bottom surface of the package. However, to take full advantage
of this feature, the PCB must have features to effectively
conduct heat away from the package. This can be achieved by
incorporating thermal pad and thermal vias on the PCB. While
a thermal pad provides a solderable surface on the top surface
of the PCB (to solder the package die paddle on the board),
thermal vias are needed to provide a thermal path to inner
and/or bottom layers of the PCB to remove the heat.
Lastly, all ground connections should be made as short as
possible. This results in the lowest impedance return paths and
the quietest ground connections.
SIGNAL ROUTING
The digital Rx and Tx signal paths should be kept as short as
possible. Also, the impedance of these traces should have a
controlled characteristic impedance of about 50 Ω. This
prevents poor signal integrity and the high currents that can
Rev. A | Page 44 of 48
AD9865
occur during undershoot or overshoot caused by ringing. If the
signal traces cannot be kept shorter than about 1.5 inches, series
termination resistors (33 Ω to 47 Ω) should be placed close to
all digital signal sources. It is a good idea to series-terminate all
clock signals at their source, regardless of trace length.
The receive RX+ and RX− signals are the most sensitive signals
on the entire board. Careful routing of these signals is essential
for good receive path performance. The RX+ and RX− signals
form a differential pair and should be routed together as a pair.
By keeping the traces adjacent to each other, noise coupled onto
the signals appears as common mode and is largely rejected by
the MxFE receive input. Keeping the driving point impedance
of the receive signal low and placing any low-pass filtering of
the signals close to the MxFE further reduces the possibility of
noise corrupting these signals.
Rev. A | Page 45 of 48
AD9865
EVALUATION BOARD
An evaluation board is available for the AD9865 and AD9866.
The digital interface to the evaluation board can be configured
for a half- or full-duplex interface. Two 40-pin and one 26-pin
male right angle headers (0.100 inches) provide easy interfacing
to test equipment such as digital data capture boards, pattern
generators, or custom digital evaluation boards (FPGA, DSP, or
ASIC). The reference clock source can originate from an external generator, crystal oscillator, or crystal. Software and an
interface cable are included to allow for programming of the SPI
registers via a PC.
The analog interface on the evaluation board provides a full
analog front-end reference design for power line applications. It
includes a power line socket, line transformer, protection diodes,
and passive filtering components. An auxiliary path allows
independent monitoring of the ac power line. The evaluation
board allows complete optimization of power line reference
designs based around the AD9865 or AD9866.
Alternatively, the evaluation board allows independent evaluation of the TxDAC, IAMP, and Rx paths via SMA connectors.
The IAMP can be easily configured for a voltage or current
mode interface via jumper settings. The TxDAC’s performance
can be evaluated directly or via an optional dual op amp driver
stage. The Rx path includes a transformer and termination
resistor allowing a calibrated differential input signal to be
injected into its front end.
The Analog Devices, Inc. website offers more information on
the AD9865/AD9866 evaluation board.
Rev. A | Page 46 of 48
AD9865
OUTLINE DIMENSIONS
9.00
BSC SQ
0.60 MAX
0.60 MAX
0.30
0.25
0.18
49
48
PIN 1
INDICATOR
8.75
BSC SQ
TOP
VIEW
PIN 1
INDICATOR
64
1
7.25
7.10 SQ*
6.95
EXPOSED PAD
(BOTTOM VIEW)
0.45
0.40
0.35
33
32
17
16
0.25 MIN
1.00
0.85
0.80
12° MAX
7.50
REF
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
0.20 REF
*COMPLIANT TO JEDEC STANDARDS MO-220-VMMD
EXCEPT FOR EXPOSED PAD DIMENSION
Figure 85. 64-Lead Lead Frame Chip Scale Package (LFCSP)
[CP-64-3]
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9865BCP
AD9865BCPRL
AD9865BCPZ1
AD9865BCPZRL1
AD9865CHIPS
AD9865-EB
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
64-Lead LFCSP
64-Lead LFCSP
64-Lead LFCSP
64-Lead LFCSP
DIE
Evaluation Board
Z = Pb-free part.
Rev. A | Page 47 of 48
Package Option
CP-64-3
CP-64-3
CP-64-3
CP-64-3
AD9865
NOTES
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C04493–0–11/04(A)
Rev. A | Page 48 of 48