AD ADF4212LBCP

a
Dual Low Power PLL
Frequency Synthesizer
ADF4212L
GENERAL DESCRIPTION
FEATURES
IDD Total, 7.5 mA
Bandwidth RF/IF, 2.4 GHz/1.0 GHz
2.7 V to 3.3 V Power Supply
Separate V P Allows Extended Tuning Voltage
Programmable Dual Modulus Prescaler
RF and IF: 8/9, 16/17, 32/33, 64/65
Programmable Charge Pump Currents
3-Wire Serial Interface
Analog and Digital Lock Detect
Fastlock Mode
Power-Down Mode
20-Lead TSSOP and 20-Lead MLF Chip Scale Package
The ADF4212L is a dual frequency synthesizer that can be used
to implement local oscillators (LO) in the up-conversion and
down-conversion sections of wireless receivers and transmitters.
It can provide the LO for both the RF and IF sections. It consists of a low noise digital PFD (Phase Frequency Detector), a
precision charge pump, a programmable reference divider, programmable A and B counters, and a dual modulus prescaler
(P/P + 1). The A (6-bit) and B (12-bit) counters, in conjunction
with the dual modulus prescaler (P/P + 1), implement an N
divider (N = BP + A). In addition, the 14-bit reference counter
(R Counter), allows selectable REFIN frequencies at the PFD
input. A complete PLL (Phase-Locked Loop) can be implemented if the synthesizer is used with external loop filters and
VCOs (Voltage Controlled Oscillators).
APPLICATIONS
Wireless Handsets (GSM, PCS, DCS, CDMA, WCDMA)
Base Stations for Wireless Radio (GSM, PCS, DCS,
CDMA, WCDMA)
Wireless LANS
Cable TV Tuners (CATV)
Communications Test Equipment
Control of all the on-chip registers is via a simple 3-wire interface
with 1.8 V compatibility. The devices operate with a power
supply ranging from 2.6 V to 3.3 V and can be powered down
when not in use.
FUNCTIONAL BLOCK DIAGRAM
VDD1
VDD2
VP1
ADF4212L
RSET
IF PHASE
FREQUENCY
DETECTOR
12-BIT IF
B-COUNTER
IFIN
VP2
CHARGE
PUMP
IF
PRESCALER
6-BIT IF
A-COUNTER
REFIN
DATA
LE
IF
LOCK
DETECT
OSCILLATOR
IFCP3 IFCP2 IFCP1
OUTPUT
MUX
22-BIT
DATA
SDOUT
REGISTER
RF
LOCK
DETECT
14-BIT RF
R-COUNTER
12-BIT RF
B-COUNTER
RFIN
RF PHASE
FREQUENCY
DETECTOR
6-BIT RF
A-COUNTER
REFERENCE
DGNDIF
CPRF
REFERENCE
RSET
FLO SWITCH
AGNDRF
MUXOUT
RFCP3 RFCP2 RFCP1
CHARGE
PUMP
RF
PRESCALER
DGNDRF
CPIF
IF CURRENT
SETTING
14-BIT IF
R-COUNTER
CLOCK
REFERENCE
FLO
AGNDIF
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2002
1
(V 1 = V 2 = 2.7 V to 3.3 V; V 1, V 2 = V
ADF4212L–SPECIFICATIONS
AGND = DGND = 0 V; T = T to T , unless otherwise noted; dBm referred to 50 .)
DD
IF
IF
A
MIN
DD
P
P
DD
to 5.5 V; AGNDRF = DGNDRF =
MAX
Parameter
B Version
B Chips2
(Typical)
RF/IF CHARACTERISTICS
RF Input Frequency (RFIN)
RF Input Sensitivity
IF Input Frequency (IFIN)
IF Input Sensitivity
0.2/2.4
–10/0
100/1000
–10/0
0.2/2.4
–10/0
100/1000
–10/0
GHz min/max
dBm min/max
MHz min/max
dBm min/max
MAXIMUM ALLOWABLE
Prescaler Output Frequency3
200
200
MHz max
REFIN CHARACTERISTICS
REFIN Input Frequency
REFIN Input Sensitivity
10/150
–5
10/150
–5
MHz min/max
dBm min
10
± 100
10
± 100
pF max
µA max
PHASE DETECTOR
Phase Detector Frequency4
75
75
MHz max
CHARGE PUMP
ICP Sink/Source
High Value
Low Value
Absolute Accuracy
RSET Range
ICP Three-State Leakage Current
Sink and Source Current Matching
ICP vs. VCP
ICP vs. Temperature
5
625
2
1.5/5.6
1
6
2
2
5
625
2
1.5/5.6
1
6
2
2
mA typ
µA typ
% typ
kΩ min/max
nA max
% typ
% typ
% typ
LOGIC INPUTS
VINH, Input High Voltage
VINL, Input Low Voltage
IINH/IINL, Input Current
CIN, Input Capacitance
1.4
0.6
±1
10
1.4
0.6
±1
10
V min
V max
µA max
pF max
LOGIC OUTPUTS
VOH, Output High Voltage
VOL, Output Low Voltage
1.4
0.4
1.4
0.4
V min
V max
POWER SUPPLIES
VDD1
VDD2
VP1, VP2
2.7/3.3
VDD1
VDD1/5.5
2.7/3.3
VDD1
VDD1/5.5
V min/V max
IDD5 (RF and IF)
RF Only
IF Only
IP (IP1 + IP2)
Low Power Sleep Mode
10
6
4
0.6
1
10
6
4
0.6
1
mA max
mA max
mA max
mA typ
µA typ
REFIN Input Capacitance
REFIN Input Current
Unit
Test Conditions/Comments
For Operation below FMIN, Use a Square Wave
VDD = 3 V
VDD = 3 V
See Figure 2 for Input Circuit.
AC-Coupled. When DC-Coupled,
0 to VDD Max (CMOS-Compatible)
Programmable: See Table V.
With RSET = 2.7 kΩ
With RSET = 2.7 kΩ
0.5 V < VCP < VP – 0.5 2% typ
0.5 V < VCP < VP – 0.5
VCP = VP/2
Open Drain 1 kΩ Pull-Up to 1.8 V
IOL = 500 µA
V min/V max
7.5 mA Typical
5.0 mA Typical
2.5 mA Typical
NOTES
1
Operating temperature range is as follows: B Version: –40°C to +85°C.
2
The B Chip specifications are given as typical values.
3
This is the maximum operating frequency of the CMOS counters. The prescaler value should be chosen to ensure that the RF input is divided down to a frequency
that is less than this value.
4
Guaranteed by design. Sample tested to ensure compliance.
5
TA = 25°C. RF = 1 GHz. Prescaler = 32/33. IF = 500 MHz. Prescaler = 16/17.
Specifications subject to change without notice.
–2–
REV. 0
ADF4212L
V to 3.3 V; V 1, V 2 = V to 5.5 V ; AGND = DGND
SPECIFICATIONS1 T(V =1T= Vto2T= 2.7, unless
otherwise noted; dBm referred to 50 .)
DD
A
Parameter
NOISE CHARACTERISTICS
RF Phase Noise Floor3
Phase Noise Performance4
IF: 540 MHz Output5
IF: 900 MHz Output6
RF: 900 MHz Output6
RF: 1750 MHz Output7
RF: 2400 MHz Output8
Spurious Signals
IF: 540 MHz Output5
IF: 900 MHz Output6
RF: 900 MHz Output6
RF: 1750 MHz Output7
RF: 2400 MHz Output8
DD
MIN
P
P
DD
RF
RF
= AGNDIF = DGNDIF = 0 V;
MAX
B Version
B Chips2
Unit
Test Conditions/Comments
–170
–162
–170
–162
dBc/Hz typ
dBc/Hz typ
–89
–87
–89
–84
–87
–89
–87
–89
–84
–87
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
@ 25 kHz PFD Frequency
@ 200 kHz PFD Frequency
@ VCO Output
@ 1 kHz Offset and 200 kHz PFD Frequency
See Note 9
See Note 9
See Note 9
@ 1 kHz Offset and 1 MHz PFD Frequency
–88/–90
–90/–94
–90/–94
–80/–82
–80/–82
–88/–90
–90/–94
–90/–94
–80/–82
–80/–82
dB typ
dB typ
dB typ
dB typ
dB typ
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
See Note 9
See Note 9
See Note 9
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
NOTES
1
Operating temperature range is as follows: B Version: –40°C to +85°C
2
The B Chip specifications are given as typical values.
3
The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20logN (where N is the N divider
value). See TPC 14.
4
The phase noise is measured with the EVAL-ADF4210/12/13EB Evaluation Board and the HP8562E Spectrum Analyzer. The spectrum analyzer provides
the REFIN for the synthesizer. (f REFOUT = 10 MHz @ 0 dBm)
5
fREFIN = 10 MHz; f PFD = 200 kHz; Offset Frequency = 1 kHz; f IF = 540 MHz; N = 2700; Loop B/W = 20 kHz
6
fREFIN = 10 MHz; f PFD = 200 kHz; Offset Frequency = 1 kHz; f RF = 900 MHz; N = 4500; Loop B/W = 20 kHz
7
fREFIN = 10 MHz; f PFD = 200 kHz; Offset Frequency = 1 kHz; f RF = 1750 MHz; N = 8750; Loop B/W = 20 kHz
8
fREFIN = 10 MHz; f PFD = 1 MHz; Offset Frequency = 1 kHz; f RF = 2400 MHz; N = 9800; Loop B/W = 20 kHz
9
Same conditions as listed on the preceding line.
Specifications subject to change without notice.
(VDD1 = VDD2 = 2.6 V to 3.3 V; VP1, VP2 = VDD to 5.5 V ; AGNDRF = DGNDRF = AGNDIF = DGNDIF = 0 V;
A
MIN to TMAX, unless otherwise noted; dBm referred to 50 .)
TIMING CHARACTERISTICS T = T
Parameter
Limit at
TMIN to TMAX
(B Version)
Unit
Test Conditions/Comments
t1
t2
t3
t4
t5
t6
10
10
25
25
10
20
ns min
ns min
ns min
ns min
ns min
ns min
DATA to CLOCK Set-Up Time
DATA to CLOCK Hold Time
CLOCK High Duration
CLOCK Low Duration
CLOCK to LE Set-Up Time
LE Pulsewidth
Guaranteed by design but not production tested.
Specifications subject to change without notice.
t3
t4
CLOCK
t1
DATA
DB20 (MSB)
t2
DB19
DB2
DB1
DB0 (LSB)
(CONTROL BIT C2)
(CONTROL BIT C1)
t6
LE
t5
LE
Figure 1. Timing Diagram
REV. 0
–3–
ADF4212L
ABSOLUTE MAXIMUM RATINGS 1, 2, 3
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
2
This device is a high performance RF integrated circuit with an ESD rating of
<2 kV, and it is ESD sensitive. Proper precautions should be taken for handling and
assembly.
3
GND = AGND = DGND = 0 V
(TA = 25°C, unless otherwise noted.)
VDD1 to GND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +3.6 V
VDD1 to VDD2 . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
VP1, VP2 to GND . . . . . . . . . . . . . . . . . . . . –0.3 V to +3.6 V
VP1, VP2 to VDD1, VDD2 . . . . . . . . . . . . . . . –0.3 V to +3.6 V
Digital I/O Voltage to GND . . . . . . –0.3 V to DVDD + 0.3 V
Analog I/O Voltage to GND . . . . . . . . –0.3 V to VDD + 0.3 V
REFIN, RFIN, IFIN to GND . . . . . . . –0.3 V to VDD + 0.3 V
Operating Temperature Range
Industrial (B Version) . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Maximum Junction Temperature . . . . . . . . . . . . . . . . 150°C
TSSOP ␪JA Thermal Impedance . . . . . . . . . . . . . 150.4°C/W
CSP ␪JA Thermal Impedance (Paddle Soldered) . . . 122°C/W
CSP ␪JA Thermal Impedance (Paddle Not Soldered) 216°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C
ORDERING GUIDE
Model
Temperature Range
Package Option*
ADF4212LBRU
ADF4212LBCP
–40°C to +85°C
–40°C to +85°C
RU-20
CP-20
*RU = Thin Shrink Small Outline Package (TSSOP)
CP = Chip Scale Package
Contact the factory for chip availability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADF4212L features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
PIN CONFIGURATION
VP2
CPRF
3
18
CPIF
17
DGNDIF
ADF4212L
16
IFIN
TOP VIEW
(Not To Scale)
15
AGNDIF
DGNDRF
4
RFIN
AGNDRF
FLO
5
6
14
RSET
REFIN
8
13
DGNDIF
9
12
MUXOUT
10
11
LE
DATA
CLK
7
–4–
CPRF
1
DGNDRF
2
RFIN
3
AGNDRF
4
FLO
5
20 19 18 17 16
ADF4212L
CHIP SCALE
PACKAGE
6
7
8
MUXOUT
CLK
DATA
19
REFIN
20
2
DGNDIF
1
VP1
VP1
VDD2
VDD1
VDD2
VP2
CPIF
LFCSP
VDD1
TSSOP
9
10
15
DGNDIF
14
IFIN
13
AGNDIF
RSET
LE
12
11
REV. 0
ADF4212L
PIN FUNCTION DESCRIPTION
Mnemonic
Description
CPRF
RF Charge Pump Output. When enabled, this provides ± ICP to the external RF loop filter, which in turn drives the
external RF VCO.
Digital Ground Pin for the RF Digital Circuitry
Input to the RF Prescaler. This small signal input is normally ac-coupled from the RF VCO.
Ground Pin for the RF Analog Circuitry
Multiplexed Output of RF/IF Programmable or Reference Dividers, RF/IF Fastlock Mode. CMOS output.
Reference Input. This is a CMOS input with a nominal threshold of VDD/2 and an equivalent input resistance of 100 kΩ.
See Figure 2. This input can be driven from a TTL or CMOS crystal oscillator, or it can be ac-coupled.
Digital Ground Pin for the IF Digital, Interface, and Control Circuitry
This multiplexer output allows either the IF/RF Lock Detect, the scaled RF, scaled IF, or the scaled Reference Frequency
to be accessed externally.
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched into
the 24-bit shift register on the CLK rising edge. This input is a high impedance CMOS input.
Serial Data Input. The serial data is loaded MSB first with the two LSBs being the control bits. This input is a high
impedance CMOS input.
Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into one of the four
latches, the latch being selected using the control bits.
Connecting a resistor between this pin and ground sets the maximum RF and IF charge pump output current. The
nominal voltage potential at the RSET pin is 0.66 V. The relationship between ICP and RSET is
DGNDRF
RFIN
AGNDRF
FLO
REFIN
DGNDIF
MUXOUT
CLK
DATA
LE
RSET
I CP MAX =
AGNDIF
IFIN
CPIF
V P2
VDD2
VDD1
V P1
REV. 0
13.5
RSET
so, with RSET = 2.7 kΩ, ICP MAX = 5 mA for both the RF and IF Charge Pumps.
Ground Pin for the IF Analog Circuitry
Input to the IF Prescaler. This small signal input is normally ac-coupled from the IF VCO.
Output from the IF Charge Pump. This is normally connected to a loop filter that drives the input to an external VCO.
Power Supply for the IF Charge Pump. This should be greater than or equal to VDD2. In systems where VDD2 is 3 V,
it can be set to 5.5 V and used to drive a VCO with a tuning range up to 5.5 V.
Power Supply for the IF, Digital, and Interface Section. Decoupling capacitors to the ground plane should be placed
as close as possible to this pin. VDD2 should have a value of between 2.6 V and 3.3 V. VDD2 must have the same
potential as VDD1.
Power Supply for the RF Section. Decoupling capacitors to the ground plane should be placed as close as possible to
this pin. VDD1 should have a value of between 2.6 V and 3.3 V. VDD1 must have the same potential as VDD2.
Power Supply for the RF Charge Pump. This should be greater than or equal to VDD1. In systems where VDD1 is 3 V,
it can be set to 5.5 V and used to drive a VCO with a tuning range up to 5.5 V.
–5–
ADF4212L–Typical Performance Characteristics
0
0
–20
VDD = 3 V
VP = 5 V
–10
OUTPUT POWER – dB
AMPLITUDE – dBm
–5
VDD = 3V, VP = 5V
ICP = 5mA
PFD FREQUENCY =
200kHz
LOOP BANDWIDTH =
20kHz
RES. BANDWIDTH = 1Hz
VIDEO BANDWIDTH = 1Hz
SWEEP = 2.5 SECONDS
AVERAGES = 20
REFERENCE
LEVEL = –3.0dBm
–10
–15
–20
–30
–40
–50
–60
–70
–85.9dB
–80
–25
–90
–30
–100
0
500
1000
1500
2000
2500
–400k
3000
–200k
1.75G
200k
400k
FREQUENCY – Hz
FREQUENCY – MHz
TPC 4. Reference Spurs, RF Side (1750 MHz, 200 kHz, 20 kHz)
TPC 1. Input Sensitivity (RF Input)
10dB/DIV
0
RL = –50dBc/Hz
rms NOISE =
1.38 DEGREES
–50
1.38” rms
–60
–5
VDD = 3 V
VP = 5 V
–70
PHASE NOISE – dBc/Hz
AMPLITUDE – dBm
–10
–15
–20
–25
–80
–90
–100
–110
–120
–130
–30
–140
–35
0
500
1000
–150
100Hz
1500
FREQUENCY – MHz
TPC 2. Input Sensitivity (IF Input)
TPC 5. Integrated Phase Noise (1750 MHz, 200 kHz/20 kHz)
0
0
OUTPUT POWER – dB
–20
–30
–40
VDD = 3V, VP = 5V
ICP = 5mA
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 SECONDS
AVERAGES = 22
REFERENCE
LEVEL = –3.2dBm
REFERENCE
LEVEL = –4.3dBm
–10
–20
OUTPUT POWER – dB
–10
1MHz
FREQUENCY OFFSET
FROM 1.75GHz CARRIER
–50
–60
–70
–30
–40
VDD = 3V, VP = 5V
ICP = 5mA
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 SECONDS
AVERAGES = 22
–50
–60
–70
–80
–80
–84.2dBc/Hz
–90
–90
–100
–100
–2k
–1k
1.75G
1k
2k
–88.8dBc/Hz
–2k
FREQUENCY – Hz
–1k
540M
FREQUENCY – Hz
1k
2k
TPC 6. Phase Noise, IF Side (540 MHz, 200 kHz/20 kHz)
TPC 3. Phase Noise, RF Side (1750 MHz, 200 kHz, 20 kHz)
–6–
REV. 0
ADF4212L
0
–130
OUTPUT POWER – dB
–20
–30
–40
VDD = 3V, VP = 5V
ICP = 5mA
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 1Hz
VIDEO BANDWIDTH = 1Hz
SWEEP = 2.5 SECONDS
AVERAGES = 20
VDD = 3V
VP = 5V
–140
PHASE NOISE – dBc/Hz
REFERENCE
LEVEL = –7.0dBm
–10
–50
–60
–70
–89.3dBc
–80
–150
–160
–170
–90
–100
–180
–400k
–200k
200k
540M
FREQUENCY – Hz
400k
10
RL = –50dBc/Hz
10000
TPC 10. Phase Noise Referred to CP Output vs.
PFD Frequency, IF Side
TPC 7. Reference Spurs, IF Side (540 MHz, 200 kHz, 20 kHz)
10dB/DIV
100
1000
PHASE DETECTOR FREQUENCY – kHz
rms NOISE =
0.83 DEGREES
6
–50
0.83” rms
–60
4
–80
2
–90
ICP – mA
PHASE NOISE – dBc/Hz
–70
–100
0
–110
–2
–120
–130
–4
–140
–6
–150
100Hz
0
1MHz
1
2
3
4
5
VCP – V
FREQUENCY OFFSET
FROM 540MHz CARRIER
TPC 8. Integrated Phase Noise (540 MHz, 200 kHz/20 kHz)
TPC 11. RF Charge Pump Output Characteristics
–130
6
VDD = 3V
VP = 5V
4
VDD = 3V
VP2 = 5.5V
2
–150
ICP – mA
PHASE NOISE – dBc/Hz
–140
0
–160
–2
–170
–4
–6
–180
10
100
1000
PHASE DETECTOR FREQUENCY – kHz
0
10000
2
3
4
5
VCP – V
TPC 9. Phase Noise Referred to CP Output vs.
PFD Frequency, RF Side
REV. 0
1
TPC 12. IF Charge Pump Output Characteristics
–7–
ADF4212L
0
0
–20
PHASE NOISE – dBc/Hz
FIRST REFERENCE SPUR – dBc/Hz
–10
–20
–40
–60
–30
–40
–50
–60
–70
–80
–80
–90
–100
0
2
1
3
–100
–40
5
4
–20
0
TUNING VOLTAGE – V
20
60
40
80
100
TEMPERATURE – C
TPC 13. RF Reference Spurs (200 kHz) vs. VTUNE
(1750 MHz, 200 kHz, 20 kHz)
TPC 16. IF Phase Noise vs. Temperature
(540 MHz, 200 kHz, 20 kHz)
0
0
–10
–20
PHASE NOISE – dBc/Hz
FIRST REFERENCE SPUR – dBc
–20
–40
–60
–80
–30
–40
–50
–60
–70
–80
–100
–90
–120
–100
0
1
2
3
5
4
0
1
TUNING VOLTAGE – V
3
4
5
TPC 17. RF Noise vs. VTUNE
0
0
–10
–10
–20
–20
PHASE NOISE – dBc/Hz
PHASE NOISE – dBc/Hz
TPC 14. IF Reference Spurs (200 kHz) vs. VTUNE
(1750 MHz, 200 kHz, 20 kHz)
–30
–40
–50
–60
–70
–30
–40
–50
–60
–70
–80
–80
–90
–90
–100
–40
2
TUNING VOLTAGE – V
–100
–20
0
20
40
60
80
100
0
TEMPERATURE – C
1
2
3
4
5
TUNING VOLTAGE – V
TPC 15. RF Phase Noise vs. Temperature
(1750 MHz, 200 kHz, 20 kHz)
TPC 18. IF Noise vs. VTUNE
–8–
REV. 0
ADF4212L
FIRST REFERENCE SPUR – dBc
0
–20
–40
–60
–80
–100
–120
–40
–20
0
20
60
40
80
100
FREQ/
MHz
s11.REAL
s11.IMAG
FREQ/
MHz
s11.REAL
s11.IMAG
50
150
250
350
450
550
650
750
850
950
1050
1150
1250
1350
1450
0.97692
0.942115
0.961217
0.920667
0.897441
0.888164
0.850012
0.760189
0.767363
0.779511
0.761034
0.624825
0.635364
0.630242
0.634506
–0.021077
–0.110459
–0.085802
–0.18583
–0.245482
–0.282399
–0.305457
–0.358884
–0.541032
–0.585687
–0.482539
–0.530108
–0.590526
–0.592498
–0.655932
1550
1650
1750
1850
1950
2050
2150
2250
2350
2450
2550
2650
2750
2850
2950
0.561872
0.529742
0.514244
0.405754
0.379354
0.312959
0.322646
0.288881
0.199294
0.206914
0.168344
0.092764
0.036125
0.037007
–0.053842
–0.648879
–0.668172
–0.702192
–0.714541
–0.703593
–0.802878
–0.80397
–0.807055
–0.758619
–0.725029
–0.770837
–0.778619
–0.706197
–0.716939
–0.736527
TPC 21. S Parameter Data for the RF Input
TEMPERATURE – C
TPC 19. RF Spurs vs. Temperature
FIRST REFERENCE SPUR – dBc
0
–20
–40
–60
–80
–100
–120
–40
–20
0
20
60
40
80
100
TEMPERATURE – C
TPC 20. IF Spurs vs. Temperature
CIRCUIT DESCRIPTION
Reference Input Section
RF/IF Input Stage
The Reference Input Stage is shown in Figure 2. SW1 and SW2
are normally-closed switches. SW3 is normally open. When
power-down is initiated, SW3 is closed and SW1 and SW2 are
opened. This ensures that there is no loading of the REFIN pin
on power-down.
The RF/IF Input Stage is shown in Figure 3. It is followed by a
two-stage limiting amplifier to generate the CML (Current Mode
Logic) clock levels needed for the prescaler.
1.6V
BIAS
GENERATOR
POWER-DOWN
CONTROL
AVDD
2k
2k
RFINA
100k
NC
SW2
REFIN NC
RFINB
TO R COUNTER
BUFFER
SW1
SW3
NO
AGND
NC = NO CONNECT
Figure 3. RF/IF Input Stage
Figure 2. Reference Input Stage
REV. 0
–9–
ADF4212L
Prescaler (P/P + 1)
Phase Frequency Detector (PFD) and Charge Pump
The dual-modulus prescaler (P/P + 1), along with the A and B
counters, enables the large division ratio N, to be realized
(N = PB + A). The dual-modulus prescaler, operating at CML
levels, takes the clock from the RF/IF input stage and divides it
down to a manageable frequency for the CMOS A and B
counters in the RF and IF sections. The prescaler in both
sections is programmable. It can be set in software to 8/9, 16/17,
32/33, or 64/65. See Table IV and Table VI. It is based on a
synchronous 4/5 core.
The PFD takes inputs from the R counter and N counter and
produces an output proportional to the phase and frequency
difference between them. Figure 5 is a simplified schematic.
The PFD includes a fixed delay element that sets the width
of the antibacklash pulse. This is typically 3 ns. This pulse ensures
that there is no dead zone in the PFD transfer function and gives a
consistent reference spur level.
HI
RF/IF A and B Counters
+IN
UP
CLR1
U3
DELAY
Pulse Swallow Function
HI
The A and B counters, in conjunction with the dual modulus
prescaler, make it possible to generate output frequencies that
are spaced only by the Reference Frequency divided by R. The
equation for the VCO frequency is as follows:
CHARGE
PUMP
CP
CLR2
DOWN
D2
Q2
U2
–IN
Figure 5. RF/IF PFD Simplified Schematic
MUXOUT and Lock Detect
]
fVCO = ( P × B ) + A × f REFIN /R
fVCO = Output frequency of external voltage controlled
oscillator (VCO)
P
= Preset modulus of dual modulus prescaler (8/9, 16/17, and so on)
B
= Preset divide ratio of binary 13-bit counter (3 to 8191)
A
= Preset divide ratio of binary 6-bit swallow counter (0 to 63)
fREFIN = External reference frequency oscillator
R
Q1
U1
The A and B CMOS counters combine with the dual modulus
prescaler to allow a wide ranging division ratio in the PLL feedback counter. The counters are specified to work when the
prescaler output is 200 MHz or less. Typically, they will work
with 250 MHz output from the prescaler. Thus, with an RF
input frequency of 2.5 GHz, a prescaler value of 16/17 is valid,
but a value of 8/9 is not valid.
[
D1
= Preset divide ratio of binary 14-bit programmable
reference counter (1 to 16383)
The output multiplexer on the ADF4212L allows the user to
access various internal points on the chip. The state of MUXOUT is controlled by P3, P4, P11, and P12. See Table III and
Table V. Figure 6 shows the MUXOUT section in block diagram form.
Lock Detect
MUXOUT can be programmed for two types of lock detect:
digital lock detect and analog lock detect. Digital Lock Detect is
active high. It is set high when the phase error on three consecutive Phase Detector cycles is less than 15 ns. It will stay set
high until a phase error of greater than 25 ns is detected on any
subsequent PD cycle.
The N-channel open-drain Analog Lock Detect should be operated with an external pull-up resistor of 10 kΩ nominal. When
lock has been detected, it is high with narrow low going pulses.
N = BP + A
12-BIT B
COUNTER
FROM RF
INPUT STAGE
TO PFD
DVDD
LOAD
PRESCALER
P/P+1
MODULUS
CONTROL
LOAD
6-BIT A
COUNTER
IF ANALOG LOCK DETECT
IF R COUNTER OUTPUT
IF N COUNTER OUTPUT
IF/RF ANALOG LOCK DETECT
MUX
MUXOUT
CONTROL
RF R COUNTER OUTPUT
Figure 4. RF/IF A and B Counters
RF N COUNTER OUTPUT
RF/IF R Counter
RF ANALOG LOCK DETECT
The 14-bit RF/IF R counter allows the input reference frequency to be divided down to produce the input clock to the
phase frequency detector (PFD). Division ratios from 1 to
16,383 are allowed.
DGND
Figure 6. MUXOUT Schematic
–10–
REV. 0
ADF4212L
RF/IF Input Shift Register
Table I. C2, C1 Truth Table
The ADF4212L digital section includes a 24-bit input shift
register, a 14-bit IF R counter, and an 18-bit IF N counter (comprising a 6-bit IF A counter and a 12-bit IF B counter). Also
present is a 14-bit RF R counter and an 18-bit RF N counter
(comprising a 6-bit RF A counter and a 12-bit RF B counter).
Data is clocked into the 24-bit shift register on each rising edge of
CLK. The data is clocked in MSB first. Data is transferred
from the shift register to one of four latches on the rising edge of
LE. The destination latch is determined by the state of the two
control bits (C2, C1) in the shift register. These are the two
LSBs, DB1, and DB0, as shown in the timing diagram of Figure 1.
The truth table for these bits is shown in Table VI. Table I shows a
summary of how the latches are programmed.
Control Bits
C2
C1
Data Latch
0
0
1
1
IF R Counter
IF N Counter (A and B)
RF R Counter
RF N Counter (A and B)
0
1
0
1
Table II. Latch Summary
DB23
DB22
DB21
IFCP2
IFCP1
IFCP0
IF PD
POLARITY
THREE-STATE
CP
LOCK DETECT
PRECISION
IF CP CURRENT
SETTING
IF FO
IF R COUNTER LATCH
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P4
P3
P2
P1
CONTROL
BITS
15-BIT REFERENCE COUNTER
R15
R14
R13
R12
R11
R10
R9
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
R8
R7
R6
R5
R4
R3
R2
R1
DB1
DB0
C2 (0) C1 (0)
IF CP
GAIN
IF
POWER-DOWN
IF N COUNTER LATCH
IF
PRESCALER
DB23
DB22
DB21
P8
P7
P6
12-BIT B COUNTER
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P5
B12
B11
B10
B9
B8
B7
B6
CONTROL
BITS
6-BIT A COUNTER
B5
B4
B3
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
B2
B1
A6
A5
A4
A3
A2
A1
DB1
DB0
C2 (0) C1 (1)
DB23
DB22
DB21
RFCP2 RFCP1 RFCP0
RF PD
POLARITY
THREE-STATE
CP
RF LOCK
DETECT
RF CP CURRENT
SETTING
RF FO
RF R COUNTER LATCH
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P12
P11
P10
P9
CONTROL
BITS
15-BIT RF REFERENCE COUNTER
R15
R14
R13
R12
R11
R10
R9
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
R8
R7
R6
R5
R4
R3
R2
R1
DB1
DB0
C2 (1) C1 (0)
RF CP
GAIN
RF
POWER-DOWN
RF N COUNTER LATCH
RF
PRESCALER
DB23
DB22
DB21
P17
P16
P15
REV. 0
12-BIT B COUNTER
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P14
B12
B11
B10
B9
B8
B7
B6
CONTROL
BITS
6-BIT A COUNTER
B5
B4
–11–
B3
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
B2
B1
A6
A5
A4
A3
A2
A1
DB1
DB0
C2 (1) C1 (1)
ADF4212L
IF R COUNTER LATCH
DB23
DB22
DB21
IFCP2
IFCP1
IFCP0
IFCP2
IF PD
POLARITY
THREE-STATE
CP
LOCK DETECT
PRECISION
IF CP CURRENT
SETTING
IF FO
Table III. IF R Counter Latch Map
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P4
P3
P2
P1
R15
R14
R13
R12
R11
R10
R9
DB5
DB4
DB3
DB2
R8
R7
R6
R5
R4
R3
R2
R1
DB1
C2 (0) C1 (0)
..........
R3
R2
R1
DIVIDE RATIO
0
..........
0
0
1
1
0
0
0
..........
0
1
0
2
0
0
0
..........
0
1
1
3
0
0
0
..........
1
0
0
4
.
.
.
..........
.
.
.
.
.
.
.
.
.
.
.
.
1
.
1
.
1
..........
..........
..........
.
1
.
0
.
0
.
32764
1
1
1
..........
1
0
1
32765
P1
IF PD POLARITY
1
1
1
..........
1
1
0
32766
0
1
NEGATIVE
POSITIVE
1
1
1
..........
1
1
1
32767
P2
CHARGE PUMP
0
1
OUTPUT
NORMAL
THREE-STATE
DB0
R13
0
0
LOGIC LOW STATE
0
0
0
1
IF ANALOG LOCK DETECT
0
0
1
0
IF REFERENCE DIVIDER OUTPUT
0
0
1
1
IF N DIVIDER OUTPUT
0
1
0
0
RF ANALOG LOCK DETECT
0
1
0
1
RF/IF ANALOG LOCK DETECT
0
1
1
0
IF DIGITAL LOCK DETECT
0
1
1
1
LOGIC HIGH STATE
1
0
0
0
RF REFERENCE DIVIDER OUTPUT
1
0
0
1
RF N DIVIDER OUTPUT
1
0
1
0
THREE-STATE OUTPUT
1
0
1
1
IF COUNTER RESET
1
1
0
0
RF DIGITAL LOCK DETECT
1
1
0
1
RF/IF DIGITAL LOCK DETECT
1
1
1
0
RF COUNTER RESET
1
1
1
1
IF AND RF COUNTER RESET
0
DB6
0
MUXOUT
0
DB7
R14
P3
0
DB8
0
P4
IFCP0
DB9
R15
P12
P11
FROM RF R LATCH
0
0
IFCP1
CONTROL
BITS
15-BIT IF REFERENCE COUNTER
ICP (mA)
1.5k
2.7k
5.6k
0
1.1250
0.625
0.301
0
1
2.2500
1.250
0.602
0
1
0
3.3750
1.875
0.904
0
1
1
4.5000
2.500
1.205
1
0
0
5.6250
3.125
1.506
1
0
1
6.7500
3.750
1.808
1
1
0
7.7875
4.375
2.109
1
1
1
9.0000
5.000
2.411
–12–
REV. 0
ADF4212L
IF N COUNTER LATCH
IF CP
GAIN
IF
POWER-DOWN
Table IV. IF N Counter Latch Map
IF
PRESCALER
DB23
DB22
DB21
P8
P7
P6
12-BIT B COUNTER
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P5
B12
B11
B10
P6
P5 PRESCALER VALUE
0
0
1
1
0
1
0
1
B9
B8
B7
B6
CONTROL
BITS
6-BIT A COUNTER
B5
B4
B3
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
B2
B1
A6
A5
A4
A3
A2
A1
8/9
16/17
32/33
64/65
DB1
C2 (0) C1 (1)
A6
A5
..........
A2
A1
A COUNTER
DIVIDE RATIO
0
0
..........
0
0
0
0
0
..........
0
1
1
0
0
..........
1
0
2
0
0
..........
0
1
3
P7
IF POWER-DOWN
0
0
..........
0
0
4
0
1
DISABLED
ENABLED
.
.
..........
.
.
.
.
.
.
.
.
.
1
.
1
..........
..........
..........
.
0
.
0
.
60
1
1
..........
0
1
61
1
1
..........
1
0
62
1
1
..........
1
1
63
P8
IF CP GAIN
0
1
DISABLED
ENABLED
DB0
B12
B11
B10
B3
B2
B1
B COUNTER DIVIDE RATIO
0
0
0
..........
0
1
1
3
0
0
0
..........
1
0
0
4
.
.
.
..........
.
.
.
.
.
.
.
.
.
.
.
.
1
.
1
.
1
..........
..........
..........
.
1
.
0
.
0
.
4092
1
1
1
..........
1
0
1
4093
1
1
1
..........
1
1
0
4094
1
1
1
..........
1
1
1
4095
N = BP+A, P IS PRESCALER VALUE SET IN THE FUNCTION LATCH
B MUST BE GREATER THAN OR EQUAL TO A
FOR CONTIGUOUS VALUES OF N, NMIN IS (P2 – P)
REV. 0
–13–
ADF4212L
RF R COUNTER LATCH
DB23
DB22
DB21
RFCP2 RFCP1 RFCP0
RFCP2
RFCP1
RF PD
POLARITY
THREE-STATE
CP
RF CP CURRENT
SETTING
RF LOCK
DETECT
RF FO
Table V. RF R Counter Latch Map
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P12
P11
P10
P9
CONTROL
BITS
15-BIT RF REFERENCE COUNTER
R15
R14
R13
R12
R11
R10
R9
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
R8
R7
R6
R5
R4
R3
R2
R1
DB1
C2 (1) C1 (0)
R15
R14
R13
..........
R3
R2
R1
DIVIDE RATIO
0
0
0
..........
0
0
1
1
0
0
0
..........
0
1
0
2
0
0
0
..........
0
1
1
3
0
0
0
..........
1
0
0
4
.
.
.
..........
.
.
.
.
.
.
.
.
.
.
.
.
1
.
1
.
1
..........
..........
..........
.
1
.
0
.
0
.
32764
1
1
1
..........
1
0
1
32765
P9
RF PD POLARITY
1
1
1
..........
1
1
0
32766
0
1
NEGATIVE
POSITIVE
1
1
1
..........
1
1
1
32767
P10
RF CHARGE
PUMP OUTPUT
0
1
NORMAL
THREE-STATE
P4
P3
FROM IF R LATCH
0
0
DB0
P12
P11
MUXOUT
0
0
0
0
0
1
IF ANALOG LOCK DETECT
0
0
1
0
IF REFERENCE DIVIDER OUTPUT
0
0
1
1
IF N DIVIDER OUTPUT
0
1
0
0
RF ANALOG LOCK DETECT
0
1
0
1
RF/IF ANALOG LOCK DETECT
0
1
1
0
IF DIGITAL LOCK DETECT
0
1
1
1
LOGIC HIGH STATE
1
0
0
0
RF REFERENCE DIVIDER OUTPUT
1
0
0
1
RF N DIVIDER OUTPUT
1
0
1
0
THREE-STATE OUTPUT
1
0
1
1
IF COUNTER RESET
1
1
0
0
RF DIGITAL LOCK DETECT
1
1
0
1
RF/IF DIGITAL LOCK DETECT
1
1
1
0
RF COUNTER RESET
1
1
1
1
IF AND RF COUNTER RESET
LOGIC LOW STATE
ICP (mA)
RFCP0
1.5k
2.7k
5.6k
0
0
0
1.1250
0.625
0.301
0
0
1
2.2500
1.250
0.602
0
1
0
3.3750
1.875
0.904
0
1
1
4.5000
2.500
1.205
1
0
0
5.6250
3.125
1.506
1
0
1
6.7500
3.750
1.808
1
1
0
7.7875
4.375
2.109
1
1
1
9.0000
5.000
2.411
–14–
REV. 0
ADF4212L
RF N COUNTER LATCH
RF CP
GAIN
RF
POWER-DOWN
Table VI. RF N Counter Latch Map
RF
PRESCALER
DB23
DB22
DB21
P17
P16
P15
12-BIT B COUNTER
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P14
B12
B11
B10
B9
B8
B7
B6
CONTROL
BITS
6-BIT A COUNTER
B5
B4
B3
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
B2
B1
A6
A5
A4
A3
A2
A1
DB1
DB0
C2 (1) C1 (1)
A6
A5
..........
A2
A1
A COUNTER
DIVIDE RATIO
0
0
..........
0
0
0
0
0
..........
0
1
1
0
0
..........
1
0
2
0
0
..........
0
1
3
P16 RF POWER-DOWN
0
0
..........
0
0
4
0
1
.
.
..........
.
.
.
.
.
.
.
.
.
1
.
1
..........
..........
..........
.
0
.
0
.
60
1
1
..........
0
1
61
1
1
..........
1
0
62
1
1
..........
1
1
63
P15 P14 PRESCALER VALUE
0
0
1
1
0
1
0
1
8/9
16/17
32/33
64/65
DISABLED
ENABLED
P17 RF CP GAIN
0
1
DISABLED
ENABLED
B12
B11
B10
B3
B2
B1
B COUNTER DIVIDE RATIO
0
0
0
..........
0
1
1
3
0
0
0
..........
1
0
0
4
.
.
.
..........
.
.
.
.
.
.
.
.
.
.
.
.
1
.
1
.
1
..........
..........
..........
.
1
.
0
.
0
.
4092
1
1
1
..........
1
0
1
4093
1
1
1
..........
1
1
0
4094
1
1
1
..........
1
1
1
4095
N = BP+A, P IS PRESCALER VALUE SET IN THE FUNCTION LATCH
B MUST BE GREATER THAN OR EQUAL TO A
FOR CONTIGUOUS VALUES OF N, NMIN IS (P2 – P)
REV. 0
–15–
ADF4212L
PROGRAM MODES
The REFIN oscillator circuit is only disabled if both the IF and
RF power-downs are set.
Table III and Table V show how to set up the Program Modes
in the ADF4212L. The following should be noted:
The input register and latches remain active and are capable of
loading and latching data during all power-down modes.
1. IF and RF Analog Lock Detect indicate when the PLL is in
lock. When the loop is locked and either IF or RF Analog
Lock Detect is selected, then the MUXOUT pin will show a
logic high with narrow low going pulses. When the IF/RF
Analog Lock Detect is chosen, then the locked condition is
indicated only when both IF and RF loops are locked.
The IF/RF section of the devices will return to normal powered-up
operation immediately upon LE latching a “0” to the appropriate
Power-Down Bit.
2. The IF Counter Reset Mode resets the R and AB counters in
the IF section and also puts the IF charge pump into threestate. The RF Counter Reset Mode resets the R and AB
counters in the RF section and also puts the RF charge pump
into three-state. The IF and RF Counter Reset Mode does
both of the above. Upon removal of the reset bits, the AB
counter resumes counting in close alignment with the R
counter. (Maximum error is one prescaler output cycle.)
3. The Fastlock Mode uses MUXOUT to switch a second loop
filter damping resistor to ground during Fastlock operation.
Activation of Fastlock occurs whenever RF CP Gain in the
RF Reference counter is set to “1.”
IF SECTION
PROGRAMMABLE IF REFERENCE (R) COUNTER
If control bits C2, C1 are 0, 0, the data is transferred from the input
shift register to the 14-bit IFR counter. Table III shows the input shift
register data format for the IFR counter and the divide ratios possible.
IF Phase Detector Polarity
P1 sets the IF Phase Detector Polarity. When the IF VCO characteristics are positive, this should be set to “1.” When they are
negative, it should be set to “0.” See Table III.
IF Charge Pump Three-State
P2 puts the IF charge pump into three-state mode when programmed to a “1.” It should be set to “0” for normal operation.
See Table III.
IF Power-Down
It is possible to program the ADF4210 family for either synchronous or asynchronous power-down on either the IF or RF side.
IF PROGRAM MODES
Table III and Table V show how to set up the Program Modes
in the ADF4212L.
Synchronous IF Power-Down
Programming a “1” to P7 of the ADF4212L will initiate a powerdown. If P2 of the ADF4212L has been set to “0” (normal
operation), a synchronous power-down is conducted. The device
will automatically put the charge pump into three-state and complete the power-down.
IF Charge Pump Currents
Asynchronous IF Power-Down
If control bits C2, C1 are 0, 1, the data in the input register is used
to program the IF AB counter. The N counter consists of a 6-bit
swallow counter (A counter) and 12-bit programmable counter (B
counter). Table IV shows the input register data format for programming the IF AB counter and the divide ratios possible.
IFCP2, IFCP1, IFCP0 program Current Setting for the IF
charge pump. See Table III.
PROGRAMMABLE IF AB COUNTER
If P2 of the ADF4212L has been set to “1” (three-state the IF
charge pump) and P7 is subsequently set to “1,” an asynchronous
power-down is conducted. The device will go into power-down on
the rising edge of LE, which latches the “1” to the IF PowerDown Bit (P7).
IF Prescaler Value
P5 and P6 in the IF A, B Counter Latch set the IF prescaler
values. See Table IV.
Synchronous RF Power-Down
Programming a “1” to P16 of the ADF4212L will initiate a
power-down. If P10 of the ADF4212L has been set to “0”
(normal operation), a synchronous power-down is conducted.
The device will automatically put the charge pump into threestate and then complete the power-down.
IF Power-Down
Table III and Table V show the power-down bits in the ADF4212L.
IF Fastlock
Asynchronous RF Power-Down
If P10 of the ADF4212L has been set to “1” (three-state the RF
charge pump) and P16 is subsequently set to “1,” an asynchronous
power-down is conducted. The device will go into power-down on
the rising edge of LE, which latches the “1” to the RF PowerDown Bit (P16).
Activation of either synchronous or asynchronous power-down
forces the IF/RF loop’s R and AB dividers to their load state
conditions and the IF/RF input section is debiased to a high
impedance state.
The IF CP Gain Bit (P8) of the IF N Register in the ADF4212L
is the Fastlock Enable Bit. Only when this is “1” is IF Fastlock
enabled. When Fastlock is enabled, the IF CP current is set to
maximum value. Also an extra loop filter damping resistor to
ground is switched in using the FL O pin, thus compensating for
the change in loop characteristics while in Fastlock. Since the IF
CP Gain Bit is contained in the IF N Counter, only one write is
needed to both program a new output frequency and initiate Fastlock. To come out of fastlock, the IF CP Gain bit on the IF N
Register must be set to “0.” See Table IV.
–16–
REV. 0
ADF4212L
RF SECTION
Programmable RF Reference (R) Counter
RF Power-Down
Table III and Table V show the power-down bits in the
ADF4210 family.
If control bits C2, C1 are 1, 0, the data is transferred from
the input shift register to the 14-bit RFR counter. Table V
shows the input shift register data format for the RFR counter
and the divide ratios possible.
RF Fastlock
P10 puts the RF charge pump into three-state mode when programmed to a “1.” It should be set to “0” for normal operation.
See Table V.
The RF CP Gain Bit (P17) of the RF N Register in the ADF4212L
is the Fastlock Enable Bit. Only when this is “1” is IF Fastlock
enabled. When Fastlock is enabled, the RF CP current is set to
maximum value. Also, an extra loop filter damping resistor to
ground is switched in using the FL O pin, thus compensating for
the change in loop characteristics while in Fastlock. Since the
RF CP Gain Bit is contained in the RF N counter, only one
write is needed to both program a new output frequency and
initiate Fastlock. To come out of Fastlock, the RF CP Gain Bit
on the RF N Register must be set to “0.” See Table VI.
RF Program Modes
APPLICATION SECTION
RF Phase Detector Polarity
P9 sets the IF Phase Detector Polarity. When the RF VCO characteristics are positive, this should be set to “1.” When they are
negative, it should be set to “0.” See Table V.
RF Charge Pump Three-State
Table III and Table V show how to set up the Program Modes
in the ADF4212L.
Local Oscillator for GSM Handset Receiver
RF Charge Pump Currents
RFCP2, RFCP1, RFCP0 program Current Setting for the RF
charge pump. See Table V.
Programmable RF N Counter
If control bits C2, C1 are 1, 1, the data in the input register is used
to program the RF N (A + B) counter. The N counter consists
of a 6-bit swallow counter (A counter) and 12-bit programmable
counter (B counter). Table IV shows the input register data format
for programming the RF N counter and the divide ratios possible.
See Table VI.
RF Prescaler Value
P14 and P15 in the RF A, B Counter Latch set the RF prescaler
values. See Table VI.
Figure 7 shows the ADF4212L being used with a VCO to produce
the required LOs for a GSM base station transmitter or receiver.
The reference input signal is applied to the circuit at FREFIN
and, in this case, is terminated in 50 Ω. Typical GSM systems
would have a 13 MHz TCXO driving the Reference Input without
any 50 Ω termination. In order to have a channel spacing of
200 kHz (the GSM standard), the reference input must be divided
by 65, using the on-chip reference.
The RF output frequency range is 880 MHz to 915 MHz. The
loop filter is designed to give a 20 kHz loop bandwidth. The
filter is set up for a 5 mA charge pump current, and the VCO
sensitivity is 12 MHz/V. The IF output is fixed at 540 MHz.
The filter is again designed to have a bandwidth of 20 kHz, and
the system is programmed to give channel steps of 200 kHz.
RFOUT
IFOUT
VP
VDD
VP
100pF
18
100pF
18
100pF
VDD2 VDD1
1.3nF
VP1
VCC
CPRF
CPIF
VCO190-540T
18
VP2
3.3k
VCC
VCO190-902U
620pF
2.7k
100pF
ADF4212L
RSET
MUXOUT
LOCK
DETECT
100pF
1000pF 1000pF
FREFIN
REFIN
DGNDRF
AGNDRF
DGNDIF
AGNDIF
51
100pF
RFIN
IFIN
CLK
DATA
LE
51
SPI COMPATIBLE SERIAL BUS
51
DECOUPLING CAPACITORS (22F/10pF) ON V DD, VP OF THE ADF4212L AND ON V CC OF THE VCOs
HAVE BEEN OMITTED FROM THE DIAGRAM TO AID CLARITY.
Figure 7. GSM Handset Receiver Local Oscillator Using the ADF4212L
REV. 0
–17–
18
18
13nF
2.7k
18
ADF4212L
In narrow-band applications, there is generally a small variation
in output frequency (generally less than 10%) and also a small
variation in VCO sensitivity over the range (typically <10%).
However in wideband applications both of these parameters
have a much greater variation. Variations in these parameters will
change the loop bandwidth. This in turn can affect stability
and lock time. By changing the programmable ICP, it is possible
to get compensation for these varying loop conditions and ensure
that the loop is always operating close to optimal conditions.
Wideband PLL
Many of the wireless applications for synthesizers and VCOs in
PLLs are narrow-band in nature. These applications include the
various wireless standards like GSM, DSC1800, CDMA, or
WCDMA. In each of these cases, the total tuning range for the
local oscillator is less than 100 MHz. However, there are also
wideband applications where the local oscillator could have up
to an octave tuning range. For example, cable television tuners
have a total range of about 400 MHz. Figure 8 shows an application where the ADF4212L is used to control and program the
Micronetics M3500-1324. The loop filter was designed for an
RF output of 2100 MHz, a loop bandwidth of 40 kHz, a PFD
frequency of 1 MHz, ICP of 10 mA (2.5 mA synthesizer ICP
multiplied by the gain factor of 4), VCO KD of 80 MHz/V (sensitivity of the M3500-1324 at an output of 2100 MHz) and a
phase margin of 45 degrees.
VP
VDD
20V
3k
1k
VDD1 VDD2
1000pF
VP1
VP2
CPRF
1000pF
REFIN
FREFIN
RSET
51
CLK
DATA
LE
MUXOUT
100pF
VCC
V_TUNE
OUT
100pF 18
M3500-1324
3.9nF
27nF
2.7k
470
ADF4212L
130pF
18
18
GND
LOCK
DETECT
DGNDIF
AGNDIF
DGNDRF
100pF
AGNDRF
SPI COMPATIBLE SERIAL BUS
AD820
20k
RFOUT
12V
RFIN
51
DECOUPLING CAPACITORS ON V DD, VP OF THE ADF4212L, ON V CC OF THE AD820 AND ON
VCC OF THE M3500-2250 HAVE BEEN OMITTED FROM THE DIAGRAM TO AID CLARITY.
THE IF SECTION OF THE CIRCUIT HAS ALSO BEEN OMITTED TO SIMPLIFY THE SCHEMATIC.
Figure 8. Wideband PLL Circuit
–18–
REV. 0
ADF4212L
Interfacing
ADSP-2181 Interface
The ADF4212L has a simple SPI compatible serial interface for
writing to the device. SCLK, SDATA, and LE control the data
transfer. When LE (Latch Enable) goes high, the 22 bits that
have been clocked into the input register on each rising edge of
SCLK will get transferred to the appropriate latch. See Figure 1
for the Timing Diagram and Table I for the Latch Truth Table.
Figure 10 shows the interface between the ADF4212L and the
ADSP-21xx Digital Signal Processor. As previously discussed, the
ADF4212L needs a 24-bit serial word for each latch write. The
easiest way to accomplish this using the ADSP-21xx family is to
use the Autobuffered Transmit Mode of operation with Alternate Framing. This provides a means for transmitting an
entire block of serial data before an interrupt is generated. Set
up the word length for eight bits and use three memory locations for each 24-bit word. To program each 24-bit latch, store
the three 8-bit bytes, enable the Autobuffered Mode, and
then write to the transmit register of the DSP. This last operation initiates the autobuffer transfer.
The maximum allowable serial clock rate is 20 MHz. This means that
the maximum update rate possible for the device is 909 kHz or one
update every 1.1 µs. This is certainly more than adequate for systems
that will have typical lock times in hundreds of microseconds.
ADuC812 Interface
Figure 9 shows the interface between the ADF4212L and the
ADuC812 microconverter. Since the ADuC812 is based on an
8051 core, this interface can be used with any 8051-based
microcontroller. The microconverter is set up for SPI Master
Mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Each latch of the ADF4212L needs a
24-bit word. This is accomplished by writing three 8-bit bytes
from the microconverter to the device. When the third byte has
been written, the LE input should be brought high to complete
the transfer.
ADuC812
ADF4212L
SCLK
SCLK
MOSI
SDATA
LE
I/O PORTS
CE
MUXOUT
(LOCK DETECT)
Figure 9. ADuC812 to ADF4212L Interface
On first applying power to the ADF4212L, four writes (one each to
the R counter latch and the AB counter latch for both IF and
RF side) are required for the output to become active.
ADSP-21xx
When operating in the mode described, the maximum SCLOCK rate
of the ADuC812 is 4 MHz. This means that the maximum rate
at which the output frequency can be changed will be 180 kHz.
SCLK
DT
TFS
ADF4212L
SCLK
SDATA
LE
CE
I/O FLAGS
MUXOUT
(LOCK DETECT)
Figure 10. ADSP-21xx to ADF4212L Interface
REV. 0
–19–
ADF4212L
OUTLINE DIMENSIONS
20-Lead Thin Shrink Small Outline Package (TSSOP)
(RU-20)
Dimensions shown in millimeters
20
C02774–0–11/02(0)
6.60
6.50
6.40
11
4.50
4.40
4.30
1
6.40 BSC
10
PIN 1
0.65
BSC
1.20
MAX
0.15
0.05
0.20
0.09
0.30
COPLANARITY 0.19
0.10
0.75
0.60
0.45
8
0
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153AC
20-Lead Frame Chip Scale Package (LFCSP)
4x4 mm Body
(CP-20)
Dimensions shown in millimeters
0.60
MAX
4.0
BSC SQ
0.60
MAX
PIN 1
INDICATOR
TOP
VIEW
12 MAX
1.00
0.90
0.80
0.50
BSC
0.25
REF
0.05
0.02
0.00
1
2.25
2.10 SQ
1.95
BOTTOM
VIEW
0.75
0.55
0.35
0.70 MAX
0.65 NOM
20
11
10
6
5
0.30
0.23
0.18
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-1
CONTROLLING DIMENSIONS ARE IN MILLIMETERS
PRINTED IN U.S.A.
SEATING
PLANE
16
15
3.75
BSC SQ
–20–
REV. 0