MAXIM MAX8632ETI

19-3623; Rev 0; 3/05
KIT
ATION
EVALU
LE
B
A
IL
A
AV
Integrated DDR Power-Supply Solution
for Desktops, Notebooks, and Graphic Cards
Features
The MAX8632 integrates a synchronous-buck PWM controller to generate VDDQ, a sourcing and sinking LDO linear regulator to generate VTT, and a 10mA reference
output buffer to generate VTTR. The buck controller drives
two external n-channel MOSFETs to generate output voltages down to 0.7V from a 2V to 28V input with output currents up to 15A. The LDO can sink or source up to 1.5A
continuous and 3A peak current. Both the LDO output
and the 10mA reference buffer output can be made to
track the REFIN voltage. These features make the
MAX8632 ideally suited for DDR memory applications in
desktops, notebooks, and graphic cards.
Buck Controller
♦ Quick-PWM with 100ns Load-Step Response
♦ Up to 95% Efficiency
♦ 2V to 28V Input Voltage Range
♦ 1.8V/2.5V Fixed or 0.7V to 5.5V Adjustable Output
♦ Up to 600kHz Selectable Switching Frequency
♦ Programmable Current Limit with Foldback
Capability
♦ 1.7ms Digital Soft-Start
♦ Independent Shutdown and Standby Controls
♦ Overvoltage-/Undervoltage-Protection Option
♦ Power-Good Window Comparator
LDO Section
♦ Fully Integrated VTT and VTTR Capability
♦ VTT Has ±3A Sourcing/Sinking Capability
♦ Only 20µF Ceramic Capacitance Required for VTT
♦ VTT and VTTR Outputs Track VREFIN / 2
♦ All-Ceramic Output-Capacitor Designs
♦ 1.0V to 2.8V Input Voltage Range
♦ Power-Good Window Comparator
+Denotes lead-free packaging.
19
18
FB
20
VIN
DH
21
OUT
LX
TOP VIEW
BST
Pin Configuration
17
16
15
VDD
22
14
REFIN
PGND1
23
13
VTTI
GND
24
12
VTT
SKIP
25
11
PGND2
AVDD
26
10
VTTR
SHDN
27
9
VTTS
TPO
28
8
SS
2
3
4
5
6
7
POK1
POK2
STBY
1
ILIM
MAX8632
REF
DDR I and DDR II Memory Power Supplies
Desktop Computers
Notebooks and Desknotes
Graphic Cards
Game Consoles
RAID
Networking
TEMP RANGE PIN-PACKAGE
-40°C to +85°C 28 Thin QFN 5mm × 5mm
OVP/UVP
Applications
PART
MAX8632ETI+
DL
The buck controller and LDO regulators are provided with
independent current limits. Adjustable lossless foldback
current limit for the buck regulator is achieved by monitoring the drain-to-source voltage drop of the low-side
MOSFET. Additionally, overvoltage and undervoltage protection mechanisms are built in. Once the overcurrent
condition is removed, the regulator is allowed to enter
soft-start again. This helps minimize power dissipation
during a short-circuit condition. The MAX8632 allows flexible sequencing and standby power management using
the SHDN and STBY inputs, which support all DDR
operating states.
The MAX8632 is available in a small 5mm × 5mm, 28pin thin QFN package.
Ordering Information
TON
The PWM controller in the MAX8632 utilizes Maxim’s
proprietary Quick-PWM™ architecture with programmable switching frequencies of up to 600kHz. This control
scheme handles wide input/output voltage ratios with
ease and provides 100ns response to load transients
while maintaining high efficiency and a relatively constant switching frequency. The MAX8632 offers fully programmable UVP/OVP and skip-mode options ideal in
portable applications. Skip mode allows for improved
efficiency at lighter loads.
The VTT and VTTR outputs track to within 1% of VREFIN / 2.
The high bandwidth of this LDO regulator allows excellent transient response without the need for bulk capacitors, thus reducing cost and size.
5mm x 5mm THIN QFN
Typical Operating Circuit appears at end of data sheet.
Quick-PWM is a trademark of Maxim Integrated Products, Inc.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX8632
General Description
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
ABSOLUTE MAXIMUM RATINGS
VTTS to GND............................................-0.3V to (AVDD + 0.3V)
PGND1, PGND2, TP0 to GND ...............................-0.3V to +0.3V
REF Short Circuit to GND ...........................................Continuous
Continuous Power Dissipation (TA = +70°C)
28-Pin 5mm x 5mm Thin QFN (derate 35.7mW/°C
above +70°C).................................................................2.86W
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
VIN to GND .............................................................-0.3V to +30V
VDD, AVDD , VTTI to GND .........................................-0.3V to +6V
SHDN, REFIN to GND ..............................................-0.3V to +6V
SS, POK1, POK2, SKIP, ILIM, FB to GND ................-0.3V to +6V
STBY, TON, REF, UVP/OVP to GND ........-0.3V to (AVDD + 0.3V)
OUT, VTTR to GND ..................................-0.3V to (AVDD + 0.3V)
DL to PGND1..............................................-0.3V to (VDD + 0.3V)
DH to LX ....................................................-0.3V to (VBST + 0.3V)
LX to BST..................................................................-6V to +0.3V
LX to GND .................................................................-2V to +30V
VTT to GND...............................................-0.3V to (VVTTI + 0.3V)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = +15V, VDD = AVDD = V SHDN = STBY = VBST = VILIM = 5V, VOUT = VREFIN = VVTTI = 2.5V, UVP/OVP = TP0 = FB = SKIP
= GND, PGND1 = PGND2 = LX = GND, TON = OPEN, VVTTS = VVTT, TA = -40°C to +85°C, unless otherwise noted. Typical values
are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
MAIN PWM CONTROLLER
Input Voltage Range
Output Adjust Range
VIN
2
28
VDD, AVDD
4.5
5.5
VOUT
Output Voltage Accuracy
(Note 2)
Soft-Start Ramp Time
tSS
0.7
0.693
0.7
0.707
FB = GND
2.47
2.5
2.53
FB = VDD
1.78
1.8
1.82
Rising edge of SHDN to full current limit
TON = GND (600kHz)
On-Time
Minimum Off-Time
VIN Quiescent Supply Current
tON
tOFF_MIN
AVDD Quiescent Supply Current
VIN = 15V,
VOUT = 1.5V
(Note 3)
IAVDD
IVDD
219
213
243
273
352
389
TON = AVDD (200kHz)
461
516
571
200
300
450
ns
25
40
µA
1
5
µA
STBY = GND (only VTTR and PWM on)
Rising edge of VIN
ms
194
316
All on (PWM, VTT, and VTTR on)
AVDD Undervoltage-Lockout
Threshold
V
TON = open (300kHz)
SHDN = GND
SHDN = GND
2
170
V
TON = REF (450kHz)
(Note 3)
AVDD + VDD Shutdown Supply
Current
VDD Quiescent Supply Current
1.7
IIN
VIN Shutdown Supply Current
5.5
FB = OUT
V
2.5
5
1
2
20
4.05
4.25
Hysteresis
50
Set VFB = 0.8V
1
_______________________________________________________________________________________
4.40
ns
mA
µA
V
mV
5
µA
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
(VIN = +15V, VDD = AVDD = V SHDN = STBY = VBST = VILIM = 5V, VOUT = VREFIN = VVTTI = 2.5V, UVP/OVP = TP0 = FB = SKIP
= GND, PGND1 = PGND2 = LX = GND, TON = OPEN, VVTTS = VVTT, TA = -40°C to +85°C, unless otherwise noted. Typical values
are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
AVDD = 4.5V to 5.5V; IREF = 0
1.98
2
2.02
V
REFERENCE
Reference Voltage
VREF
Reference Load Regulation
IREF = 0 to 50µA
REF Undervoltage Lockout
0.01
V
VREF rising
1.93
V
Hysteresis
300
mV
FAULT DETECTION
OVP Trip Threshold
(Referred to Nominal VOUT)
UVP/OVP = AVDD
UVP Trip Threshold
(Referred to Nominal VOUT)
112
116
120
%
65
70
75
%
POK1 Trip Threshold
(Referred to Nominal VOUT)
Lower level, falling edge, 1% hysteresis
87
90
93
Upper level, rising edge, 1% hysteresis
107
110
113
POK2 Trip Threshold
(Referred to Nominal VVTTS
and VVTTR)
Lower level, falling edge, 1% hysteresis
87.5
90
92.5
Upper level, rising edge, 1% hysteresis
107.5
110
112.5
%
POK2 Disable Threshold
(Measured at REFIN)
VREFIN rising (hysteresis = 75mV typ)
0.7
UVP Blanking Time
From rising edge of SHDN
10
OVP, UVP, POK_ Propagation
Delay
20
0.9
V
40
ms
10
POK_ Output Low Voltage
ISINK = 4mA
POK_ Leakage Current
ILIM Adjustment Range
%
VPOK_ = 5.5V, VFB = 0.8V, VVTTS = 1.3V
VILIM
0.25
ILIM Input Leakage Current
Current-Limit Threshold (Fixed)
PGND1 to LX
µs
0.3
V
1
µA
2.00
V
0.1
µA
45
50
55
mV
Current-Limit Threshold
(Adjustable) PGND1 to LX
VILIM = 2V
170
200
235
mV
Current-Limit Threshold (Fixed,
Negative Direction) PGND1 to LX
SKIP = AVDD
-75
-60
-45
mV
Current-Limit Threshold
(Adjustable, Negative Direction)
PGND1 to LX
SKIP = AVDD, VILIM = 2V
-250
mV
3
mV
Thermal-Shutdown Threshold
+160
°C
Thermal-Shutdown Hysteresis
15
°C
Zero-Crossing Detection
Threshold PGND1 to LX
_______________________________________________________________________________________
3
MAX8632
ELECTRICAL CHARACTERISTICS (continued)
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
ELECTRICAL CHARACTERISTICS (continued)
(VIN = +15V, VDD = AVDD = V SHDN = STBY = VBST = VILIM = 5V, VOUT = VREFIN = VVTTI = 2.5V, UVP/OVP = TP0 = FB = SKIP
= GND, PGND1 = PGND2 = LX = GND, TON = OPEN, VVTTS = VVTT, TA = -40°C to +85°C, unless otherwise noted. Typical values
are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
1
4
Ω
DL Gate-Driver On-Resistance in
High State
1
4
Ω
DL Gate-Driver On-Resistance in
Low State
0.5
3
Ω
MOSFET DRIVERS
DH Gate-Driver On-Resistance
Dead Time (Additional to
Adaptive Delay)
VBST - VLX = 5V
DH falling to DL rising
30
DL falling to DH rising
50
ns
INPUTS AND OUTPUTS
Logic Input Threshold
(SHDN, STBY, SKIP)
Rising edge
Logic Input Current
(SHDN, STBY, SKIP)
Dual-Mode™ Input Logic
Levels (FB)
1.7
0.05
2.1
-0.1
High
µA
V
3.15
3.85
1.65
2.35
0.5
-3
+3
µA
FB = GND
90
175
350
FB = AVDD
70
135
270
FB adjustable mode
400
800
1600
10
25
Ω
0.1
0.20
V
OUT Discharge-Mode
On-Resistance
DL Turn-On Level During
Discharge Mode
(Measured at OUT)
0.01
Dual Mode is a trademark of Maxim Integrated Products, Inc.
4
V
+0.1
REF
Low
OUT Input Resistance
µA
AVDD 0.4
Floating
Logic Input Current
(TON, OVP/UVP)
V
mV
+1
Low (2.5V output)
High (1.8V output)
2.20
225
-1
Input Bias Current (FB)
Four-Level Input Logic Levels
(TON, OVP/UVP)
1.20
Hysteresis
_______________________________________________________________________________________
kΩ
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
(VIN = +15V, VDD = AVDD = V SHDN = STBY = VBST = VILIM = 5V, VOUT = VREFIN = VVTTI = 2.5V, UVP/OVP = TP0 = FB = SKIP
= GND, PGND1 = PGND2 = LX = GND, TON = OPEN, VVTTS = VVTT, TA = -40°C to +85°C, unless otherwise noted. Typical values
are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
LINEAR REGULATORS (VTTR AND VTT)
VTTI Input Voltage Range
VVTTI
VTTI Supply Current
IVTTI
REFIN Input Impedance
VREFIN = 2.5V
VREFIN
12
0.01
ISS
20
1
VTT, VTTR UVLO Threshold
(Measured at OUT)
Soft-Start Charge Current
<0.1
SHDN = GND
VTTI Shutdown Current
REFIN Range
1
IVTT = IVTTR = 0
VSS = 0
0.1
2.8
V
1
mA
10
µA
30
kΩ
2.8
V
0.20
V
4
µA
VTT Internal MOSFET High-Side
On-Resistance
IVTT = -100mA, VVTTI = 1.5V,
AVDD = 4.5V
0.3
Ω
VTT Internal MOSFET Low-Side
On-Resistance
IVTT = 100mA, AVDD = 4.5V
0.3
Ω
VTT Output Accuracy
(Referred to VREFIN / 2)
VREFIN = 1.5V or 2.5V, IVTT = 1mA
+1
%
VTT Load Regulation
VTT Current Limit
VREFIN = 2.5V, IVTT = 0 to ±1.5A
1.3
VREFIN = 1.5V, IVTT = 0 to ±1A
1.3
VTT = 0 or VTTI
VTTS Input Current
IVTTS
-1
±3
VVTTS = 1.5V, VTT open
VTTR Output Error
(Referred to VREFIN / 2)
VREFIN = 1.5V or 2.5V, IVTTR = 0
VTTR Current Limit
VVTTR = 0 or VVTTI
VTTR Bias Current
VREFIN = VVTTI = 0
±5
±6.5
A
0.1
1
µA
+1
%
±32
±50
mA
0.6
4
µA
-1
±18
%
Note 1: Specifications to -40°C are guaranteed by design, not production tested.
Note 2: When the inductor is in continuous conduction, the output voltage has a DC regulation level higher than the error-comparator threshold by 50% of the ripple. In discontinuous conduction, the output voltage has a DC regulation level higher than the
trip level by approximately 1.5% due to slope compensation.
Note 3: On-time and off-time specifications are measured from 50% point to 50% point at the DH pin with LX = GND, VBST = 5V,
and a 250pF capacitor connected from DH to LX. Actual in-circuit times may differ due to MOSFET switching speeds.
_______________________________________________________________________________________
5
MAX8632
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VVIN = 12V, VOUT = 2.5V, TON = GND, SKIP = AVDD, circuit of Figure 8, TA = +25°C, unless otherwise noted.)
VOUT = 1.8V
60
50
VOUT = 1.5V
40
30
60
VOUT = 1.8V
50
VOUT = 1.5V
40
30
20
20
SKIP = GND
10
0.01
0.1
1
SKIP = AVDD
0
100
10
SKIP = GND
10
SKIP = AVDD
0
0.01
0.1
1
2
3
4
5
6
7
9 10 11 12
8
ILOAD (A)
SWITCHING FREQUENCY vs. INPUT VOLTAGE
(TON = GND)
SWITCHING FREQUENCY vs. TEMPERATURE
(TON = GND)
OUTPUT VOLTAGE
vs. LOAD CURRENT
680
2.525
ILOAD = 12A
660
650
2.510
2.505
620
2.500
610
2.495
1.26
1.28
0.90
1.25
1.26
0.89
1.24
0.88
1.23
0.87
1.22
1.20
0.86
1.21
1.18
0.85
1.20
1.22
VVTT = 1.25V
-2
-1
0
IVTT (A)
1
2
3
20
35
50
65
SKIP = AVDD
0
80
2
4
6
8
10
TEMPERATURE (°C)
ILOAD (A)
VTTR VOLTAGE
vs. VTTR CURRENT
LINE REGULATION
(VOUT vs. VIN)
2.54
2.53
2.52
1.24
12
2.55
VOUT (V)
0.91
VVTT = 0.9V
1.30
5
MAX8632 toc08
1.27
VVTTR (V)
0.92
VVTT (V)
1.28
SKIP = GND
2.490
-40 -25 -10
0.93
1.32
2.515
630
VTT VOLTAGE
vs. VTT CURRENT
1.34
2.520
640
8 10 12 14 16 18 20 22 24 26 28
MAX8632 toc07
2.530
670
600
6
VIN = 15V,
TON = GND
2.535
14
MAX8632 toc09
ILOAD = 0A
2.540
MAX8632 toc05
690
VOUT (V)
ILOAD = 12A
700
MAX8632 toc04
700
680
660
640
620
600
580
560
540
520
500
480
460
440
420
400
VIN (V)
6
0
100
10
SKIP = AVDD
ILOAD (A)
4
-3
1
SKIP = GND
ILOAD (A)
FREQUENCY (kHz)
FREQUENCY (kHz)
VOUT = 2.5V
70
700
650
600
550
500
450
400
350
300
250
200
150
100
50
0
MAX8632 toc03
80
FREQUENCY (kHz)
VOUT = 2.5V
70
fSW = 300kHz
90
EFFICIENCY (%)
EFFICIENCY (%)
80
MAX8632 toc02
fSW = 600kHz
90
100
MAX8632 toc01
100
SWITCHING FREQUENCY vs. LOAD CURRENT
(TON = GND)
EFFICIENCY vs. LOAD CURRENT
(TON = OPEN)
MAX8632 toc06
EFFICIENCY vs. LOAD CURRENT
(TON = GND)
VVTT (V)
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
ILOAD = 0A
2.51
2.50
ILOAD = 12A
2.49
2.48
2.47
2.46
2.45
-15
-10
-5
0
5
10
15
4
6
8 10 12 14 16 18 20 22 24 26 28
IVTTR (mA)
_______________________________________________________________________________________
VIN (V)
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
(VVIN = 12V, VOUT = 2.5V, TON = GND, SKIP = AVDD, circuit of Figure 8, TA = +25°C, unless otherwise noted.)
LOAD TRANSIENT (BUCK)
LOAD TRANSIENT VTT (-1.5A TO +1.5A)
IVTT = 1.5A, IVTTR = 15mA
LOAD TRANSIENT VTT (-3A TO +3A)
MAX8632 toc11
MAX8632 toc10
MAX8632 toc12
VOUT
50mV/div
VOUT
100mV/div
VOUT
50mV/div
ILOAD = 12A, IVTTR = 15mA
ILOAD = 12A, IVTTR = 15mA
VTT
50mV/div
VTTR
50mV/div
ILOAD
5A/div
VTT
50mV/div
VTT
50mV/div
VTTR
50mV/div
0A
VTTR
50mV/div
0A
IVTT
1A/div
0A
IVTT
2A/div
10µs/div
10µs/div
10µs/div
POWER-UP WAVEFORMS
POWER-DOWN WAVEFORMS
STARTUP AND SHUTDOWN INTO
HEAVY LOAD, DISCHARGE DISABLED
VDD = 5V, ILOAD = 12A, IVTT = 1.5A, IVTTR = 15mA
ILOAD = 12A,
IVTT = 1.5A
OUT
2V/div
OUT
2V/div
0V
MAX8632 toc15
MAX8632 toc14
MAX8632 toc13
VDD = 5V, ILOAD = 12A, IVTT = 1.5A, IVTTR = 15mA
VOUT
1V/div
0V
VTT
1V/div
VTT
1V/div
0V
VTTR
1V/div
0V
VTT
1V/div
0V
0V
VTTR
1V/div
0V
0V
SHDN
5V/div
0V
VIN
10V/div
0V
200µs/div
1ms/div
1.8V
STANDBY RESPONSE
VTT LOADED AT 10Ω TO GND
SHUTDOWN BY LOSS OF VDD
MAX8632 toc16a
POK1
5V/div
0V
200µs/div
STARTUP AND SHUTDOWN INTO
LIGHT LOAD, DISCHARGE ENABLED
10V/div
VIN
10V/div
0V
MAX8632 toc17a
MAX8632 toc16b
SHDN
500mV/div
VDD
2V/div
4V
1.8V
5V/div
STBY
1.8V
500mV/div
VOUT
VOUT
500mV/div 500mV/div
0.9V
500mV/div
0.9V
VOUT
VTT
0.9V VTT
500mV/div
VTTR
VDL
5V/div
IOUT
5A/div
0V
0A
2ms/div
200µs/div
0.9V
500mV/div
VTTR
2ms/div
_______________________________________________________________________________________
7
MAX8632
Typical Operating Characteristics (continued)
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
Typical Operating Characteristics (continued)
(VVIN = 12V, VOUT = 2.5V, TON = GND, SKIP = AVDD, circuit of Figure 8, TA = +25°C, unless otherwise noted.)
OVERVOLTAGE AND TURN-OFF
OF BUCK OUTPUT
STANDBY RESPONSE, VTT AT NO LOAD
MAX8632 toc18
MAX8632 toc17b
5V/div
STBY
1.8V
500mV/div
0.9V
500mV/div
VOUT
1V/div
VOUT
0V
VTT
VLX
10V/div
0V
0.9V
500mV/div
VDL
5V/div
VTTR
0V
40µs/div
2ms/div
SHORT CIRCUIT AND
RECOVERY OF VDDQ
SHORT CIRCUIT AND
RECOVERY OF VDDQ
UVP DISABLED, FOLDBACK CURRENT LIMIT
MAX8632 toc21
UVP ENABLED
VOUT
2V/div
VOUT
2V/div
0V
0V
ILOAD
10A/div
ILOAD
10A/div
VTT
1V/div
0V
0A
0A
VIN
10V/div
VIN
10V/div
0V
0V
IIN
2A/div
0A
400µs/div
8
SHORT CIRCUIT OF VTT
MAX8632 toc20
MAX8632 toc19
IIN
2A/div
IVTT
5A/div
0A
0A
400µs/div
400µs/div
_______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
PIN
NAME
FUNCTION
TON
On-Time Selection-Control Input. This four-level logic input sets the nominal DH on-time. Connect to
GND, REF, AVDD, or leave TON unconnected to select the following nominal switching frequencies:
TON = AVDD (200kHz)
TON = open (300kHz)
TON = REF (450kHz)
TON = GND (600kHz)
2
OVP/
UVP
Overvoltage-/Undervoltage-Protection Control Input. This four-level logic input enables or disables the
overvoltage and/or undervoltage protection. The overvoltage limit is 116% of the nominal output
voltage. The undervoltage limit is 70% of the nominal output voltage. Discharge mode is enabled when
OVP is also enabled. Connect the OVP/UVP pin to the following pins for the desired function:
OVP/UVP = AVDD (Enable OVP and discharge mode, enable UVP.)
OVP/UVP = open (Enable OVP and discharge mode, disable UVP.)
OVP/UVP = REF (Disable OVP and discharge mode, enable UVP.)
OVP/UVP = GND (Disable OVP and discharge mode, disable UVP.)
3
REF
+2.0V Reference Voltage Output. Bypass to GND with a 0.1µF (min) capacitor. REF can supply 50µA
for external loads. Can be used for setting voltage for ILIM. REF turns off when SHDN is low and
OUT < 0.1V.
4
ILIM
Valley Current-Limit Threshold Adjustment for Buck Regulator. The current-limit threshold across PGND
and LX is 0.1 times the voltage at ILIM. Connect ILIM to a resistive divider, typically from REF to GND,
to set the current-limit threshold between 25mV and 200mV. This corresponds to a 0.25V to 2V range at
ILIM. Connect ILIM to AVDD to select the 50mV default current-limit threshold. See the Setting the
Current Limit (Buck) section.
5
POK1
Buck Power-Good Open-Drain Output. POK1 is low when the buck output voltage is more than 10%
above or below the normal regulation point or during soft-start. POK1 is high impedance when the
output is in regulation and the soft-start circuit has terminated. POK1 is low in shutdown.
6
POK2
LDO Power-Good Open-Drain Output. In normal mode, POK2 is low when either VTTR or VTTS is more
than 10% above or below the normal regulation point, which is typically REFIN / 2. In standby mode,
POK2 responds only to the VTTR input. POK2 is low in shutdown, and when VREFIN is less than 0.8V.
7
STBY
Standby. Connect to GND for low-quiescent mode where the VTT output is open circuit. POK2 takes
input from only VTTR in this mode. PWM output can be on or off, depending on the state of SHDN.
8
SS
Soft-Start Control for VTT. Connect a capacitor (C9 in the Typical Applications Circuit of Figure 8) from
SS to ground. Leave SS open to disable soft-start. SS discharges to ground when VTT is off. See the
POR, UVLO, and Soft-Start section.
9
VTTS
Sensing Pin for Termination Supply Output. Normally connected to VTT pin to allow accurate regulation
to half the REFIN voltage. Connected to a resistive divider from VTT to GND to regulate VTT to higher
than half the REFIN voltage.
10
VTTR
Termination Reference Voltage. VTTR tracks VREFIN / 2.
1
_______________________________________________________________________________________
9
MAX8632
Pin Description
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
MAX8632
Pin Description (continued)
10
PIN
NAME
FUNCTION
11
PGND2
12
VTT
Termination Power-Supply Output. Connect VTT to VTTS to regulate to VREFIN / 2.
13
VTTI
Power-Supply Input Voltage for VTT and VTTR. Normally connected to the output of the buck regulator
for DDR application.
14
REFIN
15
FB
Feedback Input for Buck Output. Connect to AVDD for a +1.8V fixed output or to GND for a +2.5V fixed
output. For an adjustable output (0.7V to 5.5V), connect FB to a resistive divider from the output
voltage. FB regulates to +0.7V.
16
OUT
Output-Voltage Sense Connection. Connect to the positive terminal of the buck output filter capacitor.
OUT senses the output voltage to determine the on-time for the high-side switching MOSFET (Q1 in the
Typical Applications Circuit of Figure 8). OUT also serves as the buck output’s feedback input in fixedoutput modes. When discharge mode is enabled by OVP/UVP, the output capacitor is discharged
through an internal 10Ω resistor connected between OUT and GND. OUT also acts as the input to the
VTT and VTTR UVLO detector.
17
VIN
Input-Voltage Sense Connection. Connect to input power source. VIN is used only to set the PWM’s ontime one-shot timer. IN voltage range is from 2V to 28V.
18
DH
High-Side Gate-Driver Output. Swings from LX to BST. DH is low when in shutdown or UVLO.
19
LX
External Inductor Connection. Connect LX to the input side of the inductor. LX is used for both current
limit and the return supply of the DH driver.
20
BST
Boost Flying-Capacitor Connection. Connect to an external capacitor and diode according to the
Typical Applications Circuit (Figure 8). See the Boost-Supply Diode and Capacitor Selection section.
21
DL
Synchronous-Rectifier Gate-Driver Output. Swings from PGND to VDD.
22
VDD
Supply Input for the DL Gate Drive. Connect to the +4.5V to +5.5V system supply voltage. Bypass to
PGND1 with a 1µF (min) ceramic capacitor.
23
PGND1
Power Ground for Buck Controller. Connect PGND1 externally to the underside of the exposed pad.
24
GND
Analog Ground for Both Buck and LDO. Connect GND externally to the underside of the exposed pad.
25
SKIP
Pulse-Skipping Control Input. Connect to AVDD for low-noise, forced-PWM mode. Connect to GND to
enable pulse-skipping operation.
26
AVDD
Analog Supply Input for Both Buck and LDO. Connect to the +4.5V to +5.5V system supply voltage
with a series 10Ω resistor. Bypass to GND with a 1µF or greater ceramic capacitor.
27
SHDN
Shutdown Control Input. Use to control buck output. A rising edge on SHDN clears the overvoltageand undervoltage-protection fault latches (see Tables 2 and 3). Connect to AVDD for normal operation.
28
TP0
This is a test pin. Must connect to GND externally.
—
EP
Exposed pad. The exposed pad must be star-connected to GND and PGND2. See Special Layout
Considerations for LDO Section for more details.
Power Ground for VTT and VTTR. Connect PGND2 externally to the underside of the exposed pad.
External Reference Input. This is used to regulate the VTT and VTTR outputs to VREFIN / 2.
______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
MAX8632
IN
tOFF
TRIG
Q
ON-TIME
COMPUTE
TON
MAX8632
ONE-SHOT
OUT
BST
tON
S
TRIG
DH
Q
ONE-SHOT
Q
R
LX
VDD
DL
S
INTREF
Q
1.16 x INTREF
PGND
R
QUAD LEVEL
DECODE
OVP/UVP
ILIM
OVP/UVP
LATCH
BUCK ON/OFF
SHDN
VDD - 1V
1.0V
TP0
SHUTDOWN
DECODER
LX
BIAS ON/OFF
20ms
TIMER
SKIP
ZERO CROSSING
LX
STBY
OUT
0.7 x INTREF
VTT ON/OFF
VTTR ON/OFF
INTREF + 10%
DISCHARGE
LOGIC
VOUT = 1.8V
INTREF - 10%
N
VOUT = 2.5V
POK1
AVDD
2V
REFERENCE
N
GND
FB
DECODE
REF
INTREF
FB
VTTS
10kΩ
10kΩ
REFIN
0.1V
REFIN / 2 - 10%
OUT
REFIN / 2 + 10%
REFIN / 2
VTTI
VDD
N
POK2
VTT
VDD
POWER-DOWN
N
CURRENT
LIMITS
N
VTT ILIM
VTTI
PGND2
VTTR
PGND2
REFIN / 2 - 10%
REFIN / 2 + 10%
SS
Figure 1. Functional Diagram
______________________________________________________________________________________
11
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
Detailed Description
The MAX8632 combines a synchronous-buck PWM controller, an LDO linear regulator, and a 10mA reference output buffer. The buck controller drives two external
n-channel MOSFETs to deliver load currents up to 12A
and generate voltages down to 0.7V from a +2V to +28V
input. The LDO linear regulator can sink and source up to
1.5A continuous and 3A peak current with relatively fast
response. These features make the MAX8632 ideally
suited for DDR memory applications.
The MAX8632 buck regulator is equipped with a fixed
switching frequency of up to 600kHz using Maxim’s
proprietary constant on-time Quick-PWM architecture.
This control scheme handles wide input/output voltage
ratios with ease, and provides 100ns “instant-on”
response to load transients, while maintaining high efficiency with relatively constant switching frequency.
The buck controller, LDO, and a reference output
buffer are provided with independent current limits.
Lossless foldback current limit in the buck regulator is
achieved by monitoring the drain-to-source voltage
drop of the low-side FET. The ILIM input is used to
adjust this current limit. Overvoltage protection, if
selected, is achieved by latching the low-side synchronous FET on and the high-side FET off when the output
voltage is over 116% of its set output. It also features
an optional undervoltage protection by latching the
MOSFET drivers to the OFF state during an overcurrent
condition, when the output voltage is lower than 70% of
the regulated output. This helps minimize power dissipation during a short-circuit condition.
The current limit in the LDO and buffered reference output buffer is ±5A and ±32mA, respectively, and neither
have the over- or undervoltage protection. When the
current limit in either output is reached, the output no
longer regulates the voltage, but regulates the current
to the value of the current limit.
+5V Bias Supply (VDD and AVDD)
The MAX8632 requires an external +5V bias supply in
addition to the input voltage (VIN). Keeping the bias supply external to the IC improves the efficiency and eliminates the cost associated with the +5V linear regulator
that would otherwise be needed to supply the PWM circuit and the gate drivers. If stand-alone capability is
needed, then the +5V supply can be generated with an
external linear regulator such as the MAX1615. VDD,
AVDD, and IN can be connected together if the input
source is a fixed +4.5V to +5.5V supply.
VDD is the supply input for the buck regulator’s MOSFET
drivers, and AVDD supplies the power for the rest of
12
the IC. The current from the AV DD and V DD power
supply must supply the current for the IC and the gate
drive for the MOSFETs. This maximum current can be
estimated as:
IBIAS = IVDD + IAVDD + fSW × (QG1 + QG2 )
where IVDD + IAVDD are the quiescent supply currents
into VDD and AVDD, QG1 and QG2 are the total gate
charges of MOSFETs Q1 and Q2 (at VGS = 5V) in the
Typical Applications Circuit of Figure 8, and fSW is the
switching frequency.
Free-Running Constant-On-Time PWM
The Quick-PWM control architecture is a pseudo-fixedfrequency, constant on-time, current-mode regulator
with voltage feed-forward (Figure 1). This architecture
relies on the output filter capacitor’s ESR to act as a
current-sense resistor, so the output ripple voltage provides the PWM ramp signal. The control algorithm is
simple: the high-side switch on-time is determined
solely by a one-shot whose pulse width is inversely proportional to input voltage and directly proportional to
the output voltage. Another one-shot sets a minimum
off-time of 300ns (typ). The on-time one-shot is triggered if the error comparator is low, the low-side switch
current is below the valley current-limit threshold, and
the minimum off-time one-shot has timed out.
On-Time One-Shot (TON)
The heart of the PWM core is the one-shot that sets the
high-side switch on-time. This fast, low-jitter, adjustable
one-shot includes circuitry that varies the on-time in
response to input and output voltages. The high-side
switch on-time is inversely proportional to the input voltage (VIN) and is proportional to the output voltage:
t ON = K ×
(VOUT
+ ILOAD × RDS(ON)Q2
)
VIN
where K (the switching period) is set by the TON input
connection (Table 1) and RDS(ON)Q2 is the on-resistance of the synchronous rectifier (Q2) in the Typical
Applications Circuit (Figure 8). This algorithm results in
a nearly constant switching frequency despite the lack
of a fixed-frequency clock generator. The benefits of a
constant switching frequency are twofold:
1) The frequency can be selected to avoid noise-sensitive regions such as the 455kHz IF band.
2) The inductor ripple-current operating point remains
relatively constant, resulting in an easy design
methodology and predictable output voltage ripple.
______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
fSW =
VOUT + VDROP1
t ON (VIN + VDROP2 )
where VDROP1 is the sum of the parasitic voltage drops
in the inductor discharge path, including the synchronous rectifier, the inductor, and any PC board resistances; VDROP2 is the sum of the resistances in the
charging path, including the high-side switch (Q1 in the
Typical Applications Circuit of Figure 8), the inductor,
and any PC board resistances, and tON is the one-shot
on-time (see the On-Time One-Shot (TON) section.
Automatic Pulse-Skipping Mode
(SKIP = GND)
In skip mode (SKIP = GND), an inherent automatic
switchover to PFM takes place at light loads (Figure 2).
This switchover is affected by a comparator that truncates the low-side switch on-time at the inductor current’s zero crossing. The zero-crossing comparator
differentially senses the inductor current across the
synchronous-rectifier MOSFET (Q2 in the Typical
Applications Circuit of Figure 8). Once VPGND - VLX
drops below 5% of the current-limit threshold (2.5mV
for the default 50mV current-limit threshold), the comparator forces DL low (Figure 1). This mechanism causes the threshold between pulse-skipping PFM and
nonskipping PWM operation to coincide with the
boundary between continuous and discontinuous
inductor-current operation (also known as the critical
conduction point). The load-current level at which
PFM/PWM crossover occurs, ILOAD(SKIP), is equal to
half the peak-to-peak ripple current, which is a function
of the inductor value (Figure 2). This threshold is relatively constant, with only a minor dependence on the
input voltage (VIN):
× K ⎞ ⎛ VIN - VOUT ⎞
⎛V
ILOAD(SKIP) = ⎜ OUT
⎟⎜
⎟
⎝
⎠⎝
VIN
2L
⎠
where K is the on-time scale factor (see Table 1). For
example, in the Typical Applications Circuit of Figure 8
(K = 1.7µs, VOUT = 2.5V, VIN = 12V, and L = 1µH), the
pulse-skipping switchover occurs at:
⎛ 2.5V × 1.7µs ⎞ ⎛ 12V - 2.5V ⎞
⎜
⎟ = 1.68A
⎜
⎠
2 × 1µH ⎟⎠ ⎝
12V
⎝
The crossover point occurs at an even lower value if a
swinging (soft-saturation) inductor is used. The switching
waveforms can appear noisy and asynchronous when
light loading causes pulse-skipping operation, but this is
a normal operating condition that results in high lightload efficiency. Trade-offs in PFM noise vs. light-load
efficiency are made by varying the inductor value.
Generally, low inductor values produce a broader efficiency vs. load curve, while higher values result in higher
full-load efficiency (assuming that the coil resistance
Table 1. Approximate K-Factor Errors
MINIMUM VIN AT
VOUT = 2.5V
TYPICAL K-FACTOR
(h = 1.5; SEE THE
TON SETTING K-FACTOR
ERROR
DROPOUT
(µs)
(%)
PERFORMANCE
(BUCK) SECTION)
200
(TON = AVDD)
5.0
±10
3.15
300
(TON = open)
3.3
±10
3.47
450
(TON = REF)
2.2
±12.5
4.13
600
(TON = GND)
1.7
±12.5
5.61
______________________________________________________________________________________
13
MAX8632
The on-time one-shot has good accuracy at the operating points specified in the Electrical Characteristics
table (approximately ±12.5% at 600kHz and 450kHz,
and ±10% at 200kHz and 300kHz). On-times at operating points far removed from the conditions specified in
the Electrical Characteristics table can vary over a
wider range. For example, the 600kHz setting typically
runs approximately 10% slower with inputs much
greater than 5V due to the very short on-times required.
The constant on-time translates only roughly to a constant switching frequency. The on-times guaranteed in
the Electrical Characteristics table are influenced by
resistive losses and by switching delays in the highside MOSFET. Resistive losses, which include the
inductor, both MOSFETs, the output capacitor’s ESR,
and any PC board copper losses in the output and
ground, tend to raise the switching frequency as the
load increases. The dead-time effect increases the
effective on-time, reducing the switching frequency as
one or both dead times are added to the effective ontime. The dead time occurs only in PWM mode (SKIP =
VDD) and during dynamic output-voltage transitions
when the inductor current reverses at light or negative
load currents. With reversed inductor current, the inductor’s EMF causes LX to go high earlier than normal,
extending the on-time by a period equal to the DH-rising
dead time. For loads above the critical conduction point,
where the dead-time effect is no longer a factor, the
actual switching frequency is:
remains fixed) and less output voltage ripple. Penalties
for using higher inductor values include larger physical
size and degraded load-transient response, especially
at low input-voltage levels.
DC output accuracy specifications refer to the threshold
of the error comparator. When the inductor is in continuous conduction, the MAX8632 regulates the valley of the
output ripple, so the actual DC output voltage is higher
than the trip level by 50% of the output ripple voltage. In
discontinuous conduction (SKIP = GND and ILOAD <
ILOAD(SKIP)), the output voltage has a DC regulation
level higher than the error-comparator threshold by
approximately 1.5% due to slope compensation.
Forced-PWM Mode (SKIP = AVDD)
The low-noise forced-PWM mode (SKIP = AVDD) disables the zero-crossing comparator, which controls the
low-side switch on-time. This forces the low-side gatedrive waveform to constantly be the complement of the
high-side gate-drive waveform, so the inductor current
reverses at light loads while DH maintains a duty factor
of VOUT / VIN. Forced-PWM mode keeps the switching
frequency fairly constant. However, forced-PWM operation comes at a cost where the no-load VDD bias current remains between 2mA and 20mA due to the
external MOSFET’s gate charge and switching frequency. Forced-PWM mode is most useful for reducing
audio frequency noise, improving load-transient
response, and providing sink-current capability for
dynamic output-voltage adjustment.
protection circuit, this current-limit method is effective in
almost every circumstance.
In forced-PWM mode, the MAX8632 also implements a
negative current limit to prevent excessive reverse inductor currents when the buck regulator output is sinking
current. The negative current-limit threshold is set to
approximately 120% of the positive current limit and
tracks the positive current limit when VILIM is adjusted.
The current-limit threshold is adjusted with an external
resistor-divider at ILIM. A 2µA to 20µA divider current is
recommended for accuracy and noise immunity.
The current-limit threshold adjustment range is from
25mV to 200mV. In the adjustable mode, the currentlimit threshold voltage (from PGND1 to LX) is precisely
1/10th the voltage seen at ILIM. The threshold defaults
to 50mV when ILIM is connected to AVDD. The logic
threshold for switchover to the 50mV default value is
approximately AVDD - 1V.
Carefully observe the PC board layout guidelines to
ensure that noise and DC errors do not corrupt the differential current-sense signals seen between LX and GND.
POR, UVLO, and Soft-Start
Internal power-on reset (POR) occurs when AVDD rises
above approximately 2V, resetting the fault latch and
the soft-start counter, powering up the reference, and
preparing the buck regulator for operation. Until AVDD
reaches 4.25V (typ), AV DD undervoltage-lockout
Current-Limit Buck Regulator (ILIM)
Valley Current Limit
The current-limit circuit for the buck regulator portion of
the MAX8632 employs a unique “valley” current-sensing
algorithm that senses the voltage drop across LX and
PGND1 and uses the on-resistance of the rectifying
MOSFET (Q2 in the Typical Applications Circuit of
Figure 8) as the current-sensing element. If the magnitude of the current-sense signal is above the valley current-limit threshold, the PWM controller is not allowed to
initiate a new cycle (Figure 4). With valley current-limit
sensing, the actual peak current is greater than the valley current-limit threshold by an amount equal to the
inductor current ripple. Therefore, the exact current-limit
characteristic and maximum load capability are a function of the current-sense resistance, inductor value, and
input voltage. When combined with the undervoltage-
14
V -V
∆I
= IN OUT
L
∆t
IPEAK
INDUCTOR CURRENT
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
ILOAD = IPEAK / 2
0
ON-TIME
TIME
Figure 2. Pulse-Skipping/Discontinuous Crossover Point
______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
MAX8632
MAX8632
TO PWM
CONTROLLER
(SEE FIGURE 1)
CREF
REF
RA
ILIM
CILIM
RB
1.0V
VDD - 1V
LX
Figure 3. Adjustable Current-Limit Threshold
INDUCTOR CURRENT
IPEAK
ILOAD
ILOAD(MAX)
(
ILIM(VAL) = 1 - LIR
2
0
ILIMIT
)xI
LOAD
TIME
Figure 4. Valley Current-Limit Threshold
(UVLO) circuitry inhibits switching. The controller
inhibits switching by pulling DH low and holding DL low
when OVP and shutdown discharge are disabled
(OVP/UVP = REF or GND) or forcing DL high when OVP
and shutdown discharge are enabled (OVP/UVP =
AVDD or OPEN). See Table 3 for a detailed truth table
for OVP/UVP and shutdown settings. When AVDD rises
above 4.25V, the controller activates the buck regulator
and initializes the internal soft-start.
The buck regulator’s internal soft-start allows a gradual
increase of the current-limit level during startup to
reduce the input surge currents. The MAX8632 divides
the soft-start period into five phases. During the first
phase, the controller limits the current limit to only 20%
of the full current limit. If the output does not reach regulation within 425µs, soft-start enters the second phase,
and the current limit is increased by another 20%. This
process repeats until the maximum current limit is
reached, after 1.7ms, or when the output reaches the
nominal regulation voltage, whichever occurs first.
Adding a capacitor in parallel with the external ILIM
resistors creates a continuously adjustable analog softstart function for the buck regulator’s output.
Soft-start in the LDO section can be realized by connecting a capacitor between the SS pin and ground.
When VTT is turned off or placed in standby mode, or
during thermal shutdown of the LDOs, the SS capacitor
is discharged. When VTT is turned on or when the thermal limit is removed, an internal 4µA (typ) current
charges the SS capacitor. The resulting ramp voltage
on SS linearly increases the current-limit comparator
threshold to the VTT output, until full current limit is
attained when SS reaches approximately 1.6V. This
lowering of the current limit during startup limits the initial inrush current peaks, particularly when driving
capacitors. Choose the value of the SS capacitor
appropriately to set the soft-start time window. Leave
SS floating to disable the soft-start feature.
______________________________________________________________________________________
15
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
Power-OK (POK1)
POK1 is an open-drain output for a window comparator
that continuously monitors VOUT. POK1 is actively held
low when SHDN is low and during the buck regulator
output’s soft-start. After the digital soft-start terminates,
POK1 becomes high impedance as long as the output
voltage is within ±10% of the nominal regulation voltage
set by FB. When VOUT drops 10% below or rises 10%
above the nominal regulation voltage, the MAX8632
pulls POK1 low. Any fault condition forces POK1 low
until the fault latch is cleared by toggling SHDN or
cycling AVDD power below 1V. For logic-level output
voltages, connect an external pullup resistor between
POK1 and AVDD. A 100kΩ resistor works well in most
applications. Note that the POK1 window detector is
completely independent of the overvoltage- and undervoltage-protection fault detectors and the state of VTTS
and VTTR.
SHDN and Output Discharge
The SHDN input corresponds to the buck regulator and
places the buck regulator’s portion of the IC in a lowpower mode (see the Electrical Characteristics table).
SHDN is also used to reset a fault signal such as an
overvoltage or undervoltage fault.
When output discharge is enabled, (OVP/UVP = AVDD
or open) and SHDN is pulled low, or if UVP is enabled
(OVP/UVP = AVDD) and VOUT falls to 70% of its regulation set point, the MAX8632 discharges the buck regulator output (through the OUT input) through an internal
10Ω switch to ground. While the output is discharging,
DL is forced low and the PWM controller is disabled but
the reference remains active to provide an accurate
threshold. Once the output voltage drops below 0.1V,
the MAX8632 shuts down the reference and DL
remains low.
When output discharge is disabled (OVP/UVP = REF or
GND), the controller does not actively discharge the
buck output and the DL driver remains low. Under these
conditions, the buck output discharge rate is determined
by the load current and its output capacitance. The buck
regulator detects and latches the discharge-mode state
set by the OVP/UVP setting on startup.
When OUT is discharging, both VTT and VTTR outputs
remain alive and continue to track REFIN until OUT
drops to 0.1V.
STBY
The STBY input is an active-low input that is used to
shut down only the VTT output. When STBY is low, VTT
is high impedance.
Power-OK (POK2)
POK2 is the open-drain output for a window comparator that continuously monitors the VTTS input and VTTR
output. POK2 is pulled low when REFIN is less than
0.8V. POK2 is high impedance as long as the output
voltage is within ±10% of the nominal regulation voltage
as set by REFIN. When V VTTS or V VTTR rises 10%
above or 10% below its nominal regulation voltage, the
MAX8632 pulls POK2 low. For logic-level output voltages, connect an external pullup resistor between
POK2 and AVDD. A 100kΩ resistor works well in most
applications.
Current Limit (LDO for VTT
and VTTR Buffer)
The VTT output is a linear regulator that regulates the
input (VTTI) to half the VREFIN voltage. The feedback
point for VTT is at the VTTS input (Figure 1). VTT is
capable of sinking and sourcing at least 1.5A of continuous current and 3A peak current. The current limit for
VTT and VTTR is typically ±5A and ±32mA, respectively. When the current limit for either output is reached,
the outputs regulate the current, not the voltage.
Fault Protection
The MAX8632 provides overvoltage/undervoltage fault
protection in the buck controller. Select OVP/UVP to
enable and disable fault protection as shown in Table 3.
Once activated, the controller continuously monitors the
output for undervoltage and overvoltage fault conditions.
Table 2. Shutdown and Standby Control Logic
SHDN
STBY
BUCK OUTPUT (VDDQ)
VTT
VTTR
ON
AVDD*
AVDD*
ON
ON
AVDD**
GND**
ON
OFF (high impedance)
ON
GND***
X
OFF
OFF (tracking 0.5 REFIN)
OFF (tracking 0.5 REFIN)
*For DDR application, this is referred as S0 state, where all outputs are on.
**For DDR application, this is referred as S3 state, where VDDQ and VTTR are kept on, but VTT is turned off (high impedance).
***For DDR application, this is referred as S4/S5 states, where all outputs are off. Discharge mode should be selected (OVP/UVP =
AVDD or OPEN, see Table 3) to discharge the outputs.
16
______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
Undervoltage Protection (UVP)
When the output voltage drops below 70% of its regulation voltage while UVP is enabled, the controller sets
the fault latch and begins the discharge mode (see the
SHDN and Output Discharge section). When the output
voltage drops to 0.1V, the synchronous rectifier (Q2 in
the Typical Applications Circuit) turns on and clamps
the buck output to GND. UVP is ignored for at least
10ms (min) after startup or after a rising edge on
SHDN. Toggle SHDN or cycle AVDD power below 1V to
clear the fault latch and restart the controller. UVP is
disabled when OVP/UVP is left open or connected to
GND (see Table 3). UVP only applies to the buck output. The VTT and VTTR outputs do not have undervoltage protection.
Thermal Fault Protection
The MAX8632 features two thermal-fault-protection circuits. One monitors the buck-regulator portion of the IC
and the other monitors the linear regulator (VTT) and
the reference buffer output (VTTR). When the junction
temperature of the buck-regulator portion of the
MAX8632 rises above +160°C, a thermal sensor activates the fault latch, pulls POK1 low, and shuts down
the buck-controller output using discharge mode
regardless of the OVP/UVP setting. Toggle SHDN or
cycle AVDD below 1V to reactivate the controller after
the junction temperature cools by 15°C. If the VTT and
VTTR regulator portion of the IC has its die temperature
rise above +160°C, then VTT and VTTR shut off, go
high impedance, and restart after the die portion of the
IC cools by 15°C. Both thermal faults are independent.
For example, if the VTT output is overloaded to the
point that it triggers its thermal fault, the buck regulator
continues to function.
Design Procedure
Firmly establish the input voltage range (VIN) and maximum load current (ILOAD) in the buck regulator before
choosing a switching frequency and inductor operating
point (ripple current ratio or LIR). The primary design
trade-off lies in choosing a good switching frequency
and inductor operating point, and the following four factors dictate the rest of the design:
• Input Voltage Range. The maximum value (VIN(MAX))
must accommodate the worst-case voltage. The minimum value (VIN(MIN)) must account for the lowest
voltage after drops due to connectors and fuses. If
there is a choice, lower input voltages result in better
efficiency.
Table 3. OVP/UVP Fault Protection
OVP/UVP
DISCHARGE
UVP PROTECTION
OVP PROTECTION
AVDD
Yes.
Output is discharged through an
internal 10Ω resistance.
Enabled
Enabled
OPEN
Yes.
Output is discharged through an
internal 10Ω resistance.
Disabled
Enabled
REF
No.
DL forced low when SHDN is low.
Enabled
Disabled
GND
No.
DL forced low when SHDN is low.
Disabled
Disabled
______________________________________________________________________________________
17
MAX8632
Overvoltage Protection (OVP)
When the output voltage rises above 116% of the nominal regulation voltage and OVP is enabled (OVP/UVP =
AVDD or open), the OVP circuit sets the fault latch,
shuts down the PWM controller, and immediately pulls
DH low and forces DL high. This turns on the synchronous-rectifier MOSFET (Q2 in the Typical Applications
Circuit of Figure 8) with a 100% duty cycle, rapidly discharging the output capacitor and clamping the output
to ground. Once the output reaches 0.1V, DL is
switched off, preventing the possibility of a negative
voltage on the output. Toggle SHDN or cycle AVDD
below 1V to clear the fault latch and restart the controller. OVP is disabled when OVP/UVP is connected to
REF or GND (see Table 3). OVP only applies to the
buck output. The VTT and VTTR outputs do not have
overvoltage protection.
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
• Maximum Load Current. There are two values to consider. The peak load current (IPEAK) determines the
instantaneous component stresses and filtering
requirements and thus drives output capacitor selection, inductor saturation rating, and the design of the
current-limit circuit. The continuous load current
(ILOAD) determines the thermal stresses and thus
drives the selection of input capacitors, MOSFETs,
and other critical heat-contributing components.
• Switching Frequency. This choice determines the
basic trade-off between size and efficiency. The optimal frequency is largely a function of maximum input
voltage, due to MOSFET switching losses proportional to frequency and VIN2. The optimum frequency is
also a moving target due to rapid improvements in
MOSFET technology that are making higher frequencies more practical.
• Inductor Operating Point. This choice provides tradeoffs: size vs. efficiency and transient response vs. output ripple. Low inductor values provide better
transient response and smaller physical size but also
result in lower efficiency and higher output ripple due
to increased ripple currents. The minimum practical
inductor value is one that causes the circuit to operate
at the edge of critical conduction (where the inductor
current just touches zero with every cycle at maximum
load). Inductor values lower than this grant no further
size-reduction benefit. The optimum operating point is
usually found between 20% and 50% ripple current.
When pulse skipping (SKIP = low at light loads), the
inductor value also determines the load-current value
at which PFM/PWM switchover occurs.
where VFB is 0.7V, RC and RD are shown in Figure 6,
and VRIPPLE is:
VRIPPLE = LIR × ILOAD(MAX) × RESR
Setting the VTT and VTTR Voltages (LDO)
The termination power-supply output (VTT) can be set by
two different methods. First, the VTT output can be connected directly to the VTTS input to force VTT to regulate
to VREFIN / 2. Secondly, VTT can be forced to regulate
higher than VREFIN / 2 by connecting a resistive divider
from VTT to VTTS. The maximum value for VTT is VVTTI VDROPOUT where VDROPOUT = IVTT × 0.3Ω (max) at TA
= +85°C.
The termination reference voltage (VTTR) tracks 0.5
VREFIN.
Inductor Selection (Buck)
The switching frequency and inductor operating point
determine the inductor value as follows:
L =
For example: ILOAD(MAX) = 12A, VIN = 12V, VOUT =
2.5V, fSW = 600kHz, 30% ripple current or LIR = 0.3:
L =
Setting the Output Voltage (Buck)
Preset Output Voltages
The MAX8632 dual-mode operation allows the selection
of common voltages without requiring external components (Figure 5). Connect FB to GND for a fixed 2.5V
output, to AVDD for a fixed 1.8V output, or connect FB
directly to OUT for a fixed 0.7V output.
Setting the Buck Regulator Output (VOUT) with a
Resistive Voltage-Divider at FB
The buck-regulator output voltage can be adjusted from
0.7V to 5.5V using a resistive voltage-divider (Figure 6).
The MAX8632 regulates FB to a fixed reference voltage
(0.7V). The adjusted output voltage is:
⎛
R ⎞
V
VOUT = VFB ⎜1 + C ⎟ + RIPPLE
R
2
⎝
D⎠
VOUT (VIN - VOUT )
VIN × fSW × ILOAD(MAX) × LIR
2.5V (12V - 2.5V)
≈ 1µH
12V × 600kHz × 12A × 0.3
TO
ERROR
AMPLIFIER
MAX8632
FB
1.8V
(FIXED)
REF (2.0V)
2.5V
(FIXED)
0.1V
Figure 5. Dual-Mode Feedback Decoder
18
OUT
______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
VOUT
MAX8632
DL
COUT
Q2
Output Capacitor Selection (Buck)
PGND1
GND
OUT
RC
FB
RD
The output filter capacitor must have low enough equivalent series resistance (RESR) to meet output ripple and
load-transient requirements, yet have high enough ESR
to satisfy stability requirements.
For processor core voltage converters and other applications in which the output is subject to violent load
transients, the output capacitor’s size depends on how
much RESR is needed to prevent the output from dipping too low under a load transient. Ignoring the sag
due to finite capacitance:
RESR ≤
VSTEP
∆ILOAD(MAX)
Figure 6. Setting VOUT with a Resistive Voltage-Divider
Find a low-loss inductor with the lowest possible DC
resistance that fits in the allotted dimensions. Ferrite
cores are often the best choice, although powdered
iron is inexpensive and can work well at frequencies up
to 200kHz. The core must be large enough not to saturate at the peak inductor current (IPEAK):
LIR ⎞
⎛
IPEAK = ILOAD(MAX) ⎜1 +
⎟
⎝
2 ⎠
Most inductor manufacturers provide inductors in standard values, such as 1.0µH, 1.5µH, 2.2µH, 3.3µH, etc.
Also look for nonstandard values, which can provide a
better compromise in LIR across the input voltage range.
If using a swinging inductor (where the no-load inductance decreases linearly with increasing current), evaluate the LIR with properly scaled inductance values.
Input Capacitor Selection (Buck)
The input capacitor must meet the ripple current
requirement (IRMS) imposed by the switching currents:
IRMS = ILOAD
VOUT (VIN - VOUT )
VIN
IRMS has a maximum value of ILOAD / 2 when VIN = 2 ×
VOUT. For most applications, nontantalum capacitors
(ceramic, aluminum, POS, or OSCON) are preferred
due to their resistance to power-up surge currents typical of systems with a mechanical switch or connector in
series with the input. If the MAX8632 is operated as the
In applications without large and fast load transients,
the output capacitor’s size often depends on how much
RESR is needed to maintain an acceptable level of output voltage ripple. The output ripple voltage of a stepdown controller is approximately equal to the total
inductor ripple current multiplied by the output capacitor’s RESR. Therefore, the maximum RESR required to
meet ripple specifications is:
RESR ≤
VRIPPLE
ILOAD(MAX) × LIR
The actual capacitance value required relates to the
physical size needed to achieve low ESR, as well as to
the chemistry of the capacitor technology. Thus, the
capacitor is usually selected by ESR and voltage rating
rather than by capacitance value (this is true of tantalums, OSCONs, polymers, and other electrolytics).
When using low-capacity filter capacitors, such as
ceramic capacitors, size is usually determined by the
capacity needed to prevent V SAG and V SOAR from
causing problems during load transients. Generally,
once enough capacitance is added to meet the overshoot requirement, undershoot at the rising load edge
is no longer a problem (see the VSAG and VSOAR equations in the Transient Response (Buck) section).
However, low-capacity filter capacitors typically have
high-ESR zeros that can affect the overall stability (see
the Stability Requirements section).
______________________________________________________________________________________
19
MAX8632
L
LX
second stage of a two-stage power conversion system,
tantalum input capacitors are acceptable. In either configuration, choose a capacitor that has less than 10°C
temperature rise at the RMS input current for optimal
reliability and lifetime.
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
Stability Requirements
For Quick-PWM controllers, stability is determined by
the value of the ESR zero relative to the switching frequency. The boundary of instability is given by the following equation:
f
fESR ≤ SW
π
where :
fESR =
1
2π × RESR × COUT
If COUT consists of multiple same-value capacitors, as
in the Typical Applications Circuit of Figure 8, the fESR
remains the same as that of a single capacitor.
For a typical 600kHz application, the ESR zero frequency must be well below 190kHz, preferably below
100kHz. Two 150µF/4V Sanyo POS capacitors are used
to provide 12mΩ (max) of RESR. This results in a zero at
42kHz, well within the bounds of stability.
Do not put high-value ceramic capacitors directly
across the feedback sense point without taking precautions to ensure stability. Large ceramic capacitors can
have a high-ESR zero frequency and cause erratic,
unstable operation. However, it is easy to add enough
series resistance by placing the capacitors a couple of
inches downstream from the feedback sense point,
which should be as close as possible to the inductor.
Unstable operation manifests itself in two related but
distinctly different ways: double pulsing and fast-feedback loop instability. Double pulsing occurs due to
noise on the output or because the ESR is so low that
there is not enough voltage ramp in the output voltage
signal. This “fools” the error comparator into triggering
a new cycle immediately after the 400ns minimum offtime period has expired.
Double pulsing is more annoying than harmful, resulting in nothing worse than increased output ripple.
However, it can indicate the possible presence of loop
instability due to insufficient ESR. Loop instability can
result in oscillations at the output after line or load
steps. Such perturbations are usually damped but can
cause the output voltage to rise above or fall below the
tolerance limits. The easiest method for checking stability is to apply a very fast zero-to-max load transient and
carefully observe the output-voltage-ripple envelope for
overshoot and ringing. It can help to simultaneously
monitor the inductor current with an AC current probe.
Do not allow more than one cycle of ringing after the
initial step-response under/overshoot.
20
VTT Output Capacitor Selection (LDO)
A minimum value of 20µF is needed to stabilize the VTT
output. This value of capacitance limits the regulator’s
unity-gain bandwidth frequency to approximately 1.8MHz
(typ) to allow adequate phase margin for stability. To
keep the capacitor acting as a capacitor within the regulator’s bandwidth, it is important that ceramic caps with
low ESR and ESL be used.
Since the gain bandwidth is also determined by the
transconductance of the output FETs, which increases
with load current, the output capacitor may need to be
greater than 20µF if the load current exceeds 1.5A, but
can be smaller than 20µF if the maximum load current
is less than 1.5A. As a guideline, choose the minimum
capacitance and maximum ESR for the output capacitor using the following:
COUT _ MIN = 20µF ×
ILOAD
1.5A
RESR _ MAX = 5mΩ ×
1.5A
ILOAD
RESR value is measured at the unity-gain-bandwidth
frequency given by approximately:
fGBW =
36
×
COUT
ILOAD
1.5A
Once these conditions for stability are met, additional
capacitors, including those of electrolytic and tantalum
types, can be connected in parallel to the ceramic
capacitor (if desired) to further suppress noise or voltage ripple at the output.
VTTR Output Capacitor Selection (LDO)
The VTTR buffer is a scaled-down version of the VTT
regulator, with much smaller output transconductance.
Its compensation cap can therefore be smaller, and its
ESR larger, than what is required for its larger counterpart. For typical applications requiring load current up
to ±15mA, a ceramic cap with a minimum value of 1µF
is recommended (R ESR < 0.3Ω). Connect this cap
between VTTR and the analog ground plane.
VTTI Input Capacitor Selection (LDO)
Both the VTT and VTTR output stages are powered
from the same VTTI input. Their output voltages are referenced to the same REFIN input. The value of the VTTI
bypass capacitor is chosen to limit the amount of ripple/noise at VTTI, or the amount of voltage dip during a
load transient. Typically VTTI is connected to the output
of the buck regulator, which already has a large bulk
______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
MOSFET Selection (Buck)
The MAX8632 drives external, logic-level, n-channel
MOSFETs as the circuit-switch elements. The key
selection parameters:
On-resistance (RDS(ON)): the lower, the better.
Maximum drain-to-source voltage (VDSS): should be
at least 20% higher than input supply rail at the highside MOSFET’s drain.
Gate charges (QG, QGD, QGS): the lower the better.
Choose MOSFETs with rated RDS(ON) at VGS = 4.5V.
For a good compromise between efficiency and cost,
choose the high-side MOSFET that has a conduction
loss equal to its switching loss at nominal input voltage
and maximum output current (see below). For the lowside MOSFET, make sure that it does not spuriously
turn on because of dV/dt caused by the high-side
MOSFET turning on, as this results in shoot-through
current degrading efficiency. MOSFETs with a lower
QGD to QGS ratio have higher immunity to dV/dt.
For proper thermal-management design, calculate the
power dissipation at the desired maximum operating
junction temperature, maximum output current, and
worst-case input voltage. For the low-side MOSFET, the
worst case is at VIN(MAX). For the high-side MOSFET,
the worst case could be at either VIN(MIN) or VIN(MAX).
The high-side MOSFET and low-side MOSFET have different loss components due to the circuit operation.
The low-side MOSFET operates as a zero-voltage
switch; therefore, major losses are:
• The channel-conduction loss (PLSCC)
• The body-diode conduction loss (PLSDC)
• The gate-drive loss (PLSDR):
⎛
⎞
V
PLSCC = ⎜1 - OUT ⎟ × ILOAD2 × RDS(ON)
VIN ⎠
⎝
Use RDS(ON) at TJ(MAX):
PLSDC = 2ILOAD × VF × t DT × fSW
where VF is the body-diode forward-voltage drop, tDT is
the dead time (≈30ns), and fSW is the switching frequency. Because of the zero-voltage switch operation,
the low-side MOSFET gate-drive loss occurs as a result
of charging and discharging the input capacitance,
(CISS). This loss is distributed among the average DL
gate-driver’s pullup and pulldown resistance, R DL
(≈1Ω), and the internal gate resistance (RGATE) of the
MOSFET (≈2Ω). The drive power dissipated is given by:
PLSDR = CISS × VGS2 × fSW ×
RGATE
RGATE + RDL
The high-side MOSFET operates as a duty-cycle control
switch and has the following major losses:
• The channel-conduction loss (PHSCC)
• The VI overlapping switching loss (PHSSW)
• The drive loss (PHSDR)
(The high-side MOSFET does not have body-diode
conduction loss because the diode never conducts
current):
PHSCC =
VOUT
× ILOAD2 × RDS(ON)
VIN
Use RDS(ON) at TJ(MAX):
PHSSW = VIN × ILOAD × fSW ×
QGS + QGD
IGATE
where IGATE is the average DH-driver output current
determined by:
IGATE(ON) =
2.5V
RDH + RGATE
where RDH is the high-side MOSFET driver’s on-resistance (1Ω typ) and RGATE is the internal gate resistance of the MOSFET (≈2Ω):
PHSDR = QG × VGS × fSW ×
RGATE
RGATE + RDH
______________________________________________________________________________________
21
MAX8632
capacitor. Nevertheless, a ceramic capacitor of at least
10µF must be used and must be added and placed as
close as possible to the VTTI pin. This value must be
increased with larger load current, or if the trace from
the VTTI pin to the power source is long and has significant impedance. Furthermore, to prevent undesirable
VTTI bounce from coupling back to the REFIN input
and possibly causing instability in the loop, the REFIN
pin should ideally tap its signal from a separate lowimpedance DC source rather than directly from the
VTTI input. If the latter is unavoidable, increase the
amount of bypass capacitance at the VTTI input and
add additional bypass at the REFIN pin.
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
where VGS = VDD = 5V. In addition to the losses above,
allow about 20% more for additional losses because of
MOSFET output capacitances and low-side MOSFET
body-diode reverse-recovery charge dissipated in the
high-side MOSFET that is not well defined in the
MOSFET data sheet. Refer to the MOSFET data sheet
for thermal-resistance specifications to calculate the PC
board area needed to maintain the desired maximum
operating junction temperature with the above-calculated power dissipations. To reduce EMI caused by
switching noise, add a 0.1µF ceramic capacitor from the
high-side switch drain to the low-side switch source, or
add resistors in series with DH and DL to slow down the
switching transitions. Adding series resistors increases
the power dissipation of the MOSFET, so ensure that
this does not overheat the MOSFET.
MOSFET Snubber Circuit (Buck)
Fast switching transitions cause ringing because of a
resonating circuit formed by the parasitic inductance
and capacitance at the switching nodes. This high-frequency ringing occurs at LX’s rising and falling transitions and can interfere with circuit performance and
generate EMI. To dampen this ringing, an optional
series RC snubber circuit is added across each switch.
Below is a simple procedure for selecting the value of
the series RC of the snubber circuit:
1) Connect a scope probe to measure VLX to PGND1,
and observe the ringing frequency, fR.
2) Estimate the circuit parasitic capacitance (CPAR) at
LX by first finding a capacitor value, which, when
connected from LX to PGND1, reduces the ringing
frequency by half. CPAR can then be calculated as
1/3rd the value of the capacitor value found.
3) Estimate the circuit parasitic inductance (LPAR) from
the equation:
LPAR =
1
(2π × fR )
2
× CPAR
4) Calculate the resistor for critical dampening (RSNUB)
from the equation: RSNUB = 2π × fR x LPAR. Adjust
the resistor value up or down to tailor the desired
damping and the peak voltage excursion.
5) The capacitor (C SNUB) should be at least 2 to 4
times the value of CPAR to be effective.
The power loss of the snubber circuit (PRSNUB) is dissipated in the resistor and can be calculated as:
PRSNUB = CSNUB × VIN2 × fSW
where VIN is the input voltage and fSW is the switching
frequency. Choose an RSNUB power rating that meets
the specific application’s derating rule for the power
dissipation calculated.
Setting the Current Limit (Buck)
The current-sense method used in the MAX8632 makes
use of the on-resistance (R DS(ON) ) of the low-side
MOSFET (Q2 in the Typical Applications Circuit of Figure
8). When calculating the current limit, use the worst-case
maximum value for R DS(ON) from the MOSFET data
sheet, and add some margin for the rise in RDS(ON) with
temperature. A good general rule is to allow 0.5% additional resistance for each 1°C of temperature rise.
The minimum current-limit threshold must be great
enough to support the maximum load current when the
current limit is at the minimum tolerance value. The valley of the inductor current occurs at ILOAD(MAX) minus
half the ripple current; therefore:
⎛ ILOAD(MAX) × LIR ⎞
ILIM (VAL) > ILOAD(MAX) - ⎜
⎟
2
⎝
⎠
where ILIM(VAL) equals the minimum valley current-limit
threshold voltage divided by the on-resistance of Q2
(RDS(ON)Q2). For the 50mV default setting, connect ILIM
to AVDD. In adjustable mode, the valley current-limit
threshold is precisely 1/10th* the voltage seen at ILIM.
For an adjustable threshold, connect a resistive divider
from REF to GND with ILIM connected to the center tap.
The external 250mV to 2V adjustment range corresponds
to a 25mV to 200mV valley current-limit threshold. When
adjusting the current limit, use 1% tolerance resistors and
a divider current of approximately 10µA to prevent significant inaccuracy in the valley current-limit tolerance.
Foldback Current Limit
Alternately, foldback current limit can be implemented
if the UVP latch option is not available. Foldback current limit reduces the power dissipation of external
components so they can withstand indefinite overload
and short circuit, with automatic recovery after the overload or short circuit is removed. To implement foldback
current limit, connect a resistor from VOUT to ILIM (R6
in Figure 7 and in the Typical Applications Circuit of
Figure 8), in addition to the resistor-divider network (R4
*In the negative direction, the adjustable current limit is typically
-1/8th the voltage seen at ILIM.
22
______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
The following is a procedure for calculating the value of
R4, R5, and R6:
1) Calculate the voltage, VILIM(NOM), required at ILIM
when the output voltage is at nominal:
⎛ LIR ⎞
VILIM(NOM) = 10 × ILOAD(MAX) × ⎜1⎟
⎝
2 ⎠
× RDS(ON)Q2
VILIM(0V) = PFB × VILIM(NOM)
4) The value for R4 can be calculated as:
2V - VILIM(0V)
10µA
5) The parallel combination of R5 and R6, denoted
R56, is calculated as:
⎛ 2V ⎞
R56 = ⎜
⎟ - R4
⎝ 10µA ⎠
VOUT
REF
VOUT × R4 × R56
⎡V
- VILIM(NOM) - VILIM(0V) × R4 -⎤
⎢ OUT
⎥
⎢
⎥
⎢ VILIM(NOM) − VILIM(0V) × R56
⎥
⎣
⎦
(
((
(
)
R4
ILIM
R6
R5
))
)
7) Then R5 is calculated as:
R6 × R56
R6 - R56
Boost-Supply Diode and
Capacitor Selection (Buck)
A low-current Schottky diode, such as the CMDSH-3
from Central Semiconductor, works well for most applications. Do not use large-power diodes, because higher junction capacitance can charge up the voltage at
BST to the LX voltage and this exceeds the absolute
maximum rating of 6V. The boost capacitor should be
0.1µF to 4.7µF, depending on the input and output voltages, external components, and PC board layout. The
boost capacitance should be as large as possible to
prevent it from charging to excessive voltage, but small
enough to adequately charge during the minimum lowside MOSFET conduction time, which happens at maximum operating duty cycle (this occurs at minimum
input voltage). In addition, ensure that the boost capacitor does not discharge to below the minimum gate-tosource voltage required to keep the high-side MOSFET
fully enhanced for lowest on-resistance. This minimum
gate-to-source voltage (VGS(MIN)) is determined by:
VGS(MIN) = VDD x
CREF
MAX8632
R6 =
R5 =
2) Pick a percentage of foldback, PFB, from 15%
to 40%.
3) Calculate the voltage, VILIM(0V), when the output is
shorted (0V):
R4 =
6) Then R6 can be calculated as:
MAX8632
and R5) used for setting the adjustable current limit as
shown in Figure 7.
QG
CBOOST
where VDD is 5V, QG is the total gate charge of the
high-side MOSFET, and CBOOST is the boost-capacitor
value where CBOOST is C7 in the Typical Applications
Circuit (Figure 8).
GND
Figure 7. Foldback Current Limit
______________________________________________________________________________________
23
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
R6
20Ω
VTTI
C2
10µF
VTT
1.25V / ±1.5A
C1
0.1µF
REFIN
AVDD
VTT
C4
20µF
VTTS
C5
4.7µF
D1
CMDSH-3
VIN (4.5V TO 28V)
VIN
R3
100kΩ
BST
C7
0.22µF
POK1
POK1
POK2
POK2
SKIP
C8
2 x 10µF
C14
470µF
(OPTIONAL)
LX
DH
Q1
IRF7821
n-CHANNEL
30V, 9mΩ
L1
TOKO FDA1254-1R0M
1.0µH, 21A, 1.6mΩ
TON
GND
C9
3.9nF
2.5V / 12A
SS
C10
0.22µF
DL
REF
R5
47.5kΩ
5V
BIAS
SUPPLY
VDD
VTTR
C6
1µF
OVP/UVP
R2
100kΩ
R1
10Ω
MAX8632
PGND2
VTTR
1.25V / 10mA
C3
1µF
Q2
IRF7832
n-CHANNEL
30V,5mΩ
C12
150µF
C11
150µF
C13
1µF
PGND1
R4
100kΩ
ILIM
SHDN
FB
STBY
C11, C12 (150µF, 4V,
25mΩ, LOW-ESR POS
CAPACITOR (D2E)
SANYO 4TPE150M
ON
OUT
OFF
TP0
Figure 8. Typical Applications Circuit
Transient Response (Buck)
The inductor ripple current also affects transientresponse performance, especially at low VIN - VOUT differentials. Low inductor values allow the inductor
current to slew faster, replenishing charge removed
from the output filter capacitors by a sudden load step.
The output sag is also a function of the maximum duty
factor, which can be calculated from the on-time and
minimum off-time:
24
⎡V
⎤
× K
L × ∆ILOAD(MAX)2 ⎢ OUT
+ t OFF(MIN) ⎥
VIN
⎣
⎦
VSAG =
⎡ ( VIN - VOUT ) × K
⎤
2COUT × VOUT ⎢
+ t OFF(MIN) ⎥
VIN
⎢⎣
⎥⎦
where t OFF(MIN) is the minimum off-time (see the
Electrical Characteristics) and K is from Table 1.
______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
VSOAR =
∆ILOAD(MAX)2 × L
2 × COUT × VOUT
Applications Information
Dropout Performance (Buck)
The output-voltage adjustable range for continuousconduction operation is restricted by the nonadjustable
minimum off-time one-shot. For best dropout performance, use the slower (200kHz) on-time setting. When
working with low input voltages, the duty-factor limit
must be calculated using worst-case values for on- and
off-times. Manufacturing tolerances and internal propagation delays introduce an error to the TON K-factor.
This error is greater at higher frequencies (see Table
1). Also, keep in mind that transient-response performance of buck regulators operated too close to
dropout is poor, and bulk output capacitance must
often be added (see the VSAG equation in the Design
Procedure section).
The absolute point of dropout is when the inductor current ramps down during the minimum off-time (∆IDOWN)
as much as it ramps up during the on-time (∆IUP). The
ratio h = ∆IUP / ∆IDOWN indicates the controller’s ability
to slew the inductor current higher in response to
increased load, and must always be greater than 1. As
h approaches 1, the absolute minimum dropout point,
the inductor current cannot increase as much during
each switching cycle, and V SAG greatly increases,
unless additional output capacitance is used.
A reasonable minimum value for h is 1.5, but adjusting
this up or down allows trade-offs between VSAG, output
capacitance, and minimum operating voltage. For a
given value of h, the minimum operating voltage can be
calculated as:
⎡
⎤
⎢
⎥
⎢ VOUT + VDROP1 ⎥
VIN(MIN) = ⎢
+ VDROP2 - VDROP1
⎛ h × t OFF(MIN) ⎞ ⎥
⎢1 ⎥
⎜
⎟⎥
⎢⎣
K
⎝
⎠⎦
where VDROP1 and VDROP2 are the parasitic voltage
drops in the discharge and charge paths (see the OnTime One-Shot (TON) section), tOFF(MIN) is from the
Electrical Characteristics, and K is taken from Table 1.
The absolute minimum input voltage is calculated with
h = 1.
If the calculated VIN(MIN) is greater than the required
minimum input voltage, then the operating frequency
must be reduced or output capacitance added to
obtain an acceptable VSAG. If operation near dropout is
anticipated, calculate VSAG to be sure of adequate
transient response.
A dropout design example follows:
VOUT = 2.5V
fSW = 600kHz
K = 1.7µs
tOFF(MIN) = 450ns
VDROP1 = VDROP2 = 100mV
h = 1.5
⎡
⎢
VIN(MIN) = ⎢
⎢
⎢1 ⎢⎣
⎤
⎥
2.5V + 0.1V
⎥ + 0.1V - 0.1V = 4.3V
⎛ 1.5 × 450ns ⎞ ⎥
⎜
⎟⎥
1.7µs
⎝
⎠ ⎥⎦
Voltage Positioning (Buck)
In applications where fast-load transients occur, the
output voltage changes instantly by RESR × COUT ×
∆ILOAD. Voltage positioning allows the use of fewer output capacitors for such applications, and maximizes
the output-voltage AC and DC tolerance window in
tight-tolerance applications.
Figure 9 shows the connection of OUT and FB in a voltage-positioned circuit. In nonvoltage-positioned circuits, the MAX8632 regulates at the output capacitor. In
voltage-positioned circuits, the MAX8632 regulates on
the inductor side of the voltage-positioning resistor.
VOUT is reduced to:
VOUT(VPS) = VOUT(NO _ LOAD) - RPOS × ILOAD
PC Board Layout Guidelines
Careful PC board layout is critical to achieve low
switching losses and clean, stable operation. The
switching power stage requires particular attention. If
possible, mount all the power components on the top
side of the board, with their ground terminals flush
against one another. Follow these guidelines for good
PC board layout:
• Keep the high-current paths short, especially at the
ground terminals. This practice is essential for stable, jitter-free operation.
• Keep the power traces and load connections short.
This practice is essential for high efficiency. Using
______________________________________________________________________________________
25
MAX8632
The overshoot during a full-load to no-load transient
due to stored inductor energy can be calculated as:
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
+5V BIAS
SUPPLY
AVDD
VDD
IN
VIN
BST
MAX8632
DH
RPOS
VOLTAGEPOSITIONED
OUTPUT
LX
DL
PGND1
GND
FB
OUT
Figure 9. Voltage-Positioned Output
•
•
•
•
26
thick copper PC boards (2oz vs. 1oz) can enhance
full-load efficiency by 1% or more. Correctly routing
PC board traces is a difficult task that must be
approached in terms of fractions of centimeters,
where a single mΩ of excess trace resistance causes a measurable efficiency penalty.
The LX and PGND1 connections to the low-side
MOSFET for current sensing must be made using
Kelvin-sense connections.
When trade-offs in trace lengths must be made, it is
preferable to allow the inductor-charging path to be
made longer than the discharge path. For example,
it is better to allow some extra distance between the
input capacitors and the high-side MOSFET than to
allow distance between the inductor and the lowside MOSFET or between the inductor and the output filter capacitor.
Route high-speed switching nodes (BST, LX, DH,
and DL) away from sensitive analog areas (REF, FB,
and ILIM).
Input ceramic capacitors must be placed as close
as possible to the high-side MOSFET drain and the
low-side MOSFET source. Position the MOSFETs so
the impedance between the input capacitor terminals and the MOSFETs is as low as possible.
Special Layout Considerations for LDO Section
The capacitor (or capacitors) at VTT should be placed
as close to VTT and PGND2 (pins 12 and 11) as possible to minimize the series resistance/inductance of the
trace. The PGND2 side of the capacitor must be short
with a low-impedance path to the exposed pad underneath the IC. The exposed pad must be star-connected
to GND (pin 24) and PGND2 (pin 11). Connect PGND1
(pin 23) separately to the nearby PGND plane at the
source of the low-side MOSFET. Do not connect this
pin directly to the exposed pad as this can inject undesirable switching noise into the clean analog GND.
Instead, PGND1 (pin 23) is connected to PGND2 (pin
11) by the large PGND plane. A narrower trace can be
used to connect the output voltage on the VTT side of
the capacitor back to VTTS (pin 9). For best performance, the VTTI bypass capacitor must be placed as
close to VTTI (pin 13) as possible. REFIN (pin 14)
should be separately routed with a clean trace and
adequately bypassed to GND. Refer to the MAX8632
evaluation kit data sheet for PC board guidelines.
______________________________________________________________________________________
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
R8
C1
REFIN
VTTI
C2
C3
VTT
0.9V - 1.25V / 1.5A
AVDD
VTT
C4
R1
VTTS
5V
BIAS
SUPPLY
VDD
PGND2
C5
VTTR
0.9V - 1.25V / 10mA
VTTR
C6
VIN (4.5V TO 28V)
VIN
OVP/UVP
R2
D1
MAX8632
BST
R3
C8
C7
POK1
POK1
POK2
POK2
LX
Q1
SKIP
DH
TON
GND
L1
Q2
C9
SS
1.8V - 2.5V / 12A
DL
C10
C11
REF
PGND1
R4
R5
ILIM
SHDN
FB
STBY
ON
R7
R6
OUT
OFF
TP0
Chip Information
TRANSISTOR COUNT: 5100
PROCESS: BiCMOS
______________________________________________________________________________________
27
MAX8632
Typical Operating Circuit
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
QFN THIN.EPS
MAX8632
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
D2
D
MARKING
b
C
L
0.10 M C A B
D2/2
D/2
k
L
XXXXX
E/2
E2/2
C
L
(NE-1) X e
E
DETAIL A
PIN # 1
I.D.
e/2
E2
PIN # 1 I.D.
0.35x45°
e
(ND-1) X e
DETAIL B
e
L1
L
C
L
C
L
L
L
e
e
0.10 C
A
C
0.08 C
A1 A3
PACKAGE OUTLINE,
16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm
-DRAWING NOT TO SCALE-
28
21-0140
______________________________________________________________________________________
H
1
2
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
COMMON DIMENSIONS
PKG.
16L 5x5
20L 5x5
EXPOSED PAD VARIATIONS
28L 5x5
32L 5x5
40L 5x5
SYMBOL MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX.
A
A1
A3
b
D
E
e
k
L
L1
N
ND
NE
JEDEC
0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80
0
0.02 0.05
0.20 REF.
0.25 0.30 0.35
4.90 5.00 5.10
4.90 5.00 5.10
0.80 BSC.
0.25 -
0
0.02 0.05
0
0.02 0.05
0
0.02 0.05
0.20 REF.
0.20 REF.
0.20 REF.
0.25 0.30 0.35 0.20 0.25 0.30 0.20 0.25 0.30
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
0.50 BSC.
0.65 BSC.
0.50 BSC.
- 0.25 - 0.25
0.25 -
0
0.02 0.05
0.20 REF.
0.15 0.20 0.25
4.90 5.00 5.10
4.90 5.00 5.10
0.40 BSC.
0.25 0.35 0.45
0.30 0.40 0.50 0.45 0.55 0.65 0.45 0.55 0.65 0.30 0.40 0.50 0.40 0.50 0.60
- 0.30 0.40 0.50
16
4
4
20
5
5
WHHB
WHHC
28
7
7
WHHD-1
32
8
8
40
10
10
WHHD-2
-----
NOTES:
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL
CONFORM TO JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE
OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE TERMINAL #1
IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE.
D2
L
E2
PKG.
CODES
MIN.
NOM. MAX.
T1655-1
T1655-2
T1655N-1
3.00
3.00
3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10
3.10
3.10
3.20
3.20
3.20
T2055-2
T2055-3
T2055-4
3.00
3.00
3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10 3.20 3.00
3.10
3.10
3.10
3.20
3.20
3.20
T2055-5
T2855-1
T2855-2
T2855-3
T2855-4
T2855-5
T2855-6
T2855-7
T2855-8
T2855N-1
T3255-2
T3255-3
T3255-4
T3255N-1
3.15
3.15
2.60
3.15
2.60
2.60
3.15
2.60
3.15
3.15
3.00
3.00
3.00
3.00
3.25
3.25
2.70
3.25
2.70
2.70
3.25
2.70
3.25
3.25
3.10
3.10
3.10
3.10
3.15
3.15
2.60
3.15
2.60
2.60
3.15
2.60
3.15
3.15
3.00
3.00
3.00
3.00
3.25
3.25
2.70
3.25
2.70
2.70
3.25
2.70
3.25
3.25
3.10
3.10
3.10
3.10
3.35
3.35
2.80
3.35
2.80
2.80
3.35
2.80
3.35
3.35
3.20
3.20
3.20
3.20
T4055-1
3.20
3.30 3.40 3.20
3.30
3.40
3.35
3.35
2.80
3.35
2.80
2.80
3.35
2.80
3.35
3.35
3.20
3.20
3.20
3.20
MIN.
NOM. MAX.
±0.15
**
**
**
**
**
**
0.40
DOWN
BONDS
ALLOWED
NO
YES
NO
NO
YES
NO
YES
**
NO
NO
YES
YES
NO
**
**
0.40
**
**
**
**
**
NO
YES
YES
NO
NO
YES
NO
NO
**
YES
**
**
**
**
** SEE COMMON DIMENSIONS TABLE
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN
0.25 mm AND 0.30 mm FROM TERMINAL TIP.
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220, EXCEPT EXPOSED PAD DIMENSION FOR T2855-1,
T2855-3, AND T2855-6.
10. WARPAGE SHALL NOT EXCEED 0.10 mm.
11. MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY.
12. NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY.
13. LEAD CENTERLINES TO BE AT TRUE POSITION AS DEFINED BY BASIC DIMENSION "e", ±0.05.
PACKAGE OUTLINE,
16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm
21-0140
-DRAWING NOT TO SCALE-
H
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 29
© 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.
MAX8632
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)