19-2748; Rev 3; 11/03 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range Applications Automotive Remote Keyless Entry Garage Door Openers Security Systems Home Automation Remote Controls Wireless Sensors Local Telemetry Systems Features ♦ Optimized for 315MHz or 433MHz ISM Band ♦ Operates from Single 3.3V or 5.0V Supplies ♦ High Dynamic Range with On-Chip AGC ♦ Selectable Image-Rejection Center Frequency ♦ Selectable x64 or x32 fLO/fXTAL Ratio ♦ Low 5.2mA Operating Supply Current ♦ <2.5µA Low-Current Power-Down Mode for Efficient Power Cycling ♦ 250µs Startup Time ♦ Built-In 50dB RF Image Rejection ♦ Receive Sensitivity of -114dBm Ordering Information TEMP RANGE PIN-PACKAGE MAX1473EUI PART -40°C to +85°C 28 TSSOP MAX1473ETJ -40°C to +85°C 32 Thin QFN Functional Diagram and Typical Application Circuit appear at end of data sheet. LNASRC 4 25 DATAOUT AGND 5 LNAOUT 6 MAX1473 AVDD 7 XTAL1 XTAL2 PWRDN PDOUT N.C. 29 28 27 26 25 26 PDOUT AVDD 27 PWRDN LNAIN AVDD 2 LNAIN 3 30 28 XTAL2 31 XTAL1 1 LNASRC TOP VIEW 32 Pin Configurations N.C. 1 24 DATAOUT 24 VDD5 AGND 2 23 VDD5 23 DSP LNAOUT 3 22 DSP AVDD 4 21 N.C. 22 DFFB MAX1473 DGND 13 16 XTALSEL 16 17 IFIN1 DVDD 14 15 AGCDIS IFIN2 DFO MIXOUT 12 15 17 14 DSN 8 IFIN1 18 IRSEL XTALSEL 7 18 IFIN2 13 AGND IRSEL 11 12 19 DFO N.C. OPP AGND 10 AGCDIS 19 11 DFFB 6 10 20 MIXIN2 DVDD 5 20 DSN DGND MIXIN1 MIXIN2 9 9 21 OPP MIXOUT MIXIN1 8 TSSOP THIN QFN ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX1473 General Description The MAX1473 fully integrated low-power CMOS superheterodyne receiver is ideal for receiving amplitudeshift-keyed (ASK) data in the 300MHz to 450MHz frequency range. Its signal range is from -114dBm to 0dBm. With few external components and a low-current power-down mode, it is ideal for cost- and power-sensitive applications typical in the automotive and consumer markets. The chip consists of a low-noise amplifier (LNA), a fully differential image-rejection mixer, an onchip phase-locked-loop (PLL) with integrated voltagecontrolled oscillator (VCO), a 10.7MHz IF limiting amplifier stage with received-signal-strength indicator (RSSI), and analog baseband data-recovery circuitry. The MAX1473 also has a discrete one-step automatic gain control (AGC) that drops the LNA gain by 35dB when the RF input signal is greater than -57dBm. The MAX1473 is available in 28-pin TSSOP and 32-pin thin QFN packages. Both versions are specified for the extended (-40°C to +85°C) temperature range. MAX1473 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range ABSOLUTE MAXIMUM RATINGS AVDD5 to AGND ....................................................-0.3V to +6.0V AVDD to AGND ......................................................-0.3V to +4.0V DVDD to DGND......................................................-0.3V to +4.0V AGND to DGND.....................................................-0.1V to +0.1V IRSEL, DATAOUT, XTALSEL, AGCDIS, PWRDN to AGND .....................................-0.3V to (VDD5 + 0.3V) All Other Pins to AGND ..............................-0.3V to (VDD + 0.3V) Continuous Power Dissipation (TA = +70°C) 28-Pin TSSOP (derate 12.8mW/°C above +70°C) .1025.6mW 32-Pin Thin QFN (derate 21.3mW/°C above +70°C).........................................................1702.1mW Operating Temperature Ranges MAX1473E__ ..................................................-40°C to +85°C Storage Temperature Range .............................-60°C to +150°C Lead Temperature (soldering 10s) ..................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (3.3V OPERATION) (Typical Application Circuit, VDD = 3.0V to 3.6V, no RF signal applied, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VDD = 3.3V and TA = +25°C.) (Note 1) PARAMETER Supply Voltage Supply Current Shutdown Supply Current SYMBOL VDD CONDITIONS IDD V P WRDN = VDD IPWRDN V P WRDN = 0V, VXTALSEL = 0V Input Voltage Low VIL Input Voltage High VIH Input Logic Current High IIH MIN TYP MAX UNITS 3.0 3.3 3.6 V fRF = 315MHz 5.2 6.23 fRF = 433MHz 5.8 6.88 fRF = 315MHz 1.6 fRF = 433MHz 2.5 3.3V nominal supply 0.4 VDD - 0.4 DATAOUT Voltage Output Low VOL DATAOUT Voltage Output High VOH 2 V µA VDD - 0.4 fRF = 375MHz, VIRSEL = VDD/2 1.1 fRF = 315MHz, VIRSEL = 0V 0.4 RL = 5kΩ µA V 10 fRF = 433MHz, VIRSEL = VDD Image Reject Select (Note 2) 5.3 mA VDD - 0.4 _______________________________________________________________________________________ VDD - 1.5 V 0.4 V V 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range (Typical Application Circuit, VDD = 4.5V to 5.5V, no RF signal applied, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VDD = 5.0V and TA = +25°C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 4.5 5.0 5.5 V fRF = 315MHz 5.2 6.04 fRF = 433MHz 5.7 6.76 fRF = 315MHz 2.3 fRF = 433MHz 2.8 Supply Voltage VDD 5.0V nominal supply Supply Current IDD V P WRDN = VDD IPWRDN V P WRDN = 0V, VXTALSEL = 0V Shutdown Supply Current Input Voltage Low VIL Input Voltage High VIH Input Logic Current High IIH 0.4 VDD - 0.4 DATAOUT Voltage Output Low VOL DATAOUT Voltage Output High VOH 10 V µA VDD - 0.4 fRF = 375MHz, VIRSEL = VDD/2 1.1 fRF = 315MHz, VIRSEL = 0V 0.4 RL = 5kΩ µA V fRF = 433MHz, VIRSEL = VDD Image Reject Select (Note 2) 6.2 mA VDD - 1.5 V 0.4 V VDD - 0.4 V AC ELECTRICAL CHARACTERISTICS (Typical Application Circuit, VDD = 3.0V to 3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VDD = 3.3V and TA = +25°C.) (Note 1). PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS GENERAL CHARACTERISTICS Startup Time tON Receiver Input Frequency fRF Maximum Receiver Input Level Sensitivity (Note 3) Time for valid signal detection after V P WRDN = VOH 300 PRFIN_MAX Modulation depth > 18dB PRFIN_MIN AGC Hysteresis 250 450 0 Average carrier power level -120 Peak power level -114 LNA gain from low to high µs MHz dBm dBm 8 dB 150 ms 16 dB LNA IN HIGH-GAIN MODE Power Gain Input Impedance S11LNA 1dB Compression Point Input-Referred 3rd-Order Intercept Normalized to 50Ω (Note 4) fRF = 433MHz 1 - j4.7 fRF = 375MHz 1 - j3.9 fRF = 315MHz 1 - j3.4 P1dBLNA -22 dBm IIP3LNA -12 dBm _______________________________________________________________________________________ 3 MAX1473 DC ELECTRICAL CHARACTERISTICS (5.0V OPERATION) MAX1473 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range AC ELECTRICAL CHARACTERISTICS (continued) (Typical Application Circuit, VDD = 3.0V to 3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VDD = 3.3V and TA = +25°C.) (Note 1) PARAMETER SYMBOL CONDITIONS LO Signal Feedthrough to Antenna MIN TYP -80 Output Impedance S22LNA Noise Figure NFLNA Normalized to 50Ω MAX UNITS dBm 0.12 - j4.4 2 dB LNA IN LOW-GAIN MODE Input Impedance (Note 4) 1dB Compression Point Input-Referred 3rd-Order Intercept S11LNA Normalized to 50Ω fRF = 433MHz 1 - j4.7 fRF = 375MHz 1 - j3.9 fRF = 315MHz 1 - j3.4 P1dBLNA -10 dBm IIP3LNA -7 dBm -80 dBm LO Signal Feedthrough to Antenna Output Impedance S22LNA Noise Figure NFLNA Normalized to 50Ω Power Gain Voltage Gain Reduction AGC enabled (depends on tank Q) 0.4 2 dB 0 dB 35 dB MIXER Input Impedance S11MIX Input-Referred 3rd-Order Intercept IIP3MIX -18 ZOUT_MIX 330 Ω NFMIX 16 dB Output Impedance Noise Figure Image Rejection (not Including LNA Tank) Conversion Gain Normalized to 50Ω 0.25 - j2.4 fRF = 433MHz, VIRSEL = VDD 42 fRF = 375MHz, VIRSEL = VDD/2 44 fRF = 315MHz, VIRSEL = 0V 44 330Ω IF filter load 13 dBm dB dB INTERMEDIATE FREQUENCY (IF) Input Impedance Operating Frequency ZIN_IF fIF Bandpass response 3dB Bandwidth RSSI Linearity RSSI Dynamic Range RSSI Level 4 Ω MHz 20 MHz ±0.5 dB 80 dB PRFIN < -120dBm 1.15 PRFIN > 0dBm, AGC enabled 2.35 RSSI Gain AGC Threshold 330 10.7 14.2 LNA gain from low to high 1.45 LNA gain from high to low 2.05 _______________________________________________________________________________________ V mV/dB V 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range (Typical Application Circuit, VDD = 3.0V to 3.6V, all RF inputs are referenced to 50Ω, fRF = 315MHz, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VDD = 3.3V and TA = +25°C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DATA FILTER Maximum Bandwidth BWDF 100 kHz Comparator Bandwidth BWCMP 100 kHz Maximum Load Capacitance CLOAD 10 pF Output High Voltage VDD5 V Output Low Voltage 0 V DATA SLICER CRYSTAL OSCILLATOR fRF = 433MHz Crystal Frequency (Note 5) fXTAL fRF = 315MHz VXTALSEL = 0V 6.6128 VXTALSEL = VDD 13.2256 VXTALSEL = 0V 4.7547 VXTALSEL = VDD 9.5094 Crystal Tolerance Input Impedance From each pin to ground MHz MHz 50 ppm 6.2 pF Note 1: 100% tested at TA = +25°C. Guaranteed by design and characterization over temperature. Note 2: IRSEL is internally set to 375MHz IR mode. It can be left open when the 375MHz image rejection setting is desired. A 1nF capacitor is recommended in noisy environments. Note 3: BER = 2 x 10-3, Manchester encoded, data rate = 4kbps, IF bandwidth = 280kHz. Note 4: Input impedance is measured at the LNAIN pin. Note that the impedance includes the 15nH inductive degeneration connected from the LNA source to ground. The equivalent input circuit is 50Ω in series with 2.2pF. Note 5: Crystal oscillator frequency for other RF carrier frequency within the 300MHz to 450MHz range is (fRF - 10.7MHz)/64 for XTALSEL = 0V, and (fRF - 10.7MHz)/32 for XTALSEL = VDD. _______________________________________________________________________________________ 5 MAX1473 AC ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (Typical Application Circuit, VDD = 3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.) SUPPLY CURRENT vs. RF FREQUENCY +85°C 5.3 +25°C 5.1 MAX1473 toc02 fRF = 433MHz 10 +105°C 6.0 5.5 +85°C +25°C -40°C -40°C 4.5 3.1 3.2 3.3 3.4 3.5 RSSI vs. RF INPUT POWER 500 IF BANDWIDTH = 280kHz 2.2 VAGCDIS = VDD 2.0 -109 -110 -111 RSSI (V) fRF = 433MHz -108 1.8 VAGCDIS = 0V 1.6 1.4 fRF = 315MHz -15 10 35 60 85 2.0 1.5 1.8 0.5 1.6 -1.5 RSSI -2.5 -80 -60 -40 -20 0 -3.5 -90 -70 -50 -30 RF INPUT POWER (dBm) IF INPUT POWER (dBm) SYSTEM GAIN vs. FREQUENCY IMAGE REJECTION vs. RF FREQUENCY IMAGE REJECTION vs. TEMPERATURE 0 LOWER SIDEBAND -10 FROM RFIN TO MIXOUT fRF = 315MHz -20 45 40 fRF = 375MHz fRF = 433MHz 5 10 15 20 IF FREQUENCY (MHz) 25 30 60 85 44 43 fRF = 375MHz 43 42 fRF = 433MHz 41 30 -30 44 42 fRF = 315MHz 35 10 fRF = 315MHz 45 IMAGE REJECTION (dB) 10 50dB IMAGE REJECTION 50 -10 45 MAX1473 toc08 20 55 IMAGE REJECTION (dB) UPPER SIDEBAND -0.5 DELTA TEMPERATURE (°C) 30 0 2.5 1.0 -140 -120 -100 110 MAX1473 toc07 -40 3.5 2.2 1.2 1.0 -114 MAX1473 toc06 1.4 1.2 -113 -119 -118 -117 -116 -115 -114 AVERAGE INPUT POWER (dBm) 2.4 MAX1473 toc05 MAX1473 toc04 -121 -120 RSSI AND DELTA vs. IF INPUT POWER 2.4 RSSI (V) SENSITIVITY (dBm) 450 SENSITIVITY vs. TEMPERATURE -112 6 400 RF FREQUENCY (MHz) PEAK RF INPUT POWER 1% BER IF BANDWIDTH = 280MHz -107 350 SUPPLY VOLTAGE (V) -105 -106 0.01 300 250 3.6 41 280 330 380 430 RF FREQUENCY (MHz) 480 -40 -15 10 35 TEMPERATURE (°C) _______________________________________________________________________________________ DELTA (dB) 4.9 3.0 fRF = 315MHz 0.1 5.0 5.0 1 MAX1473 toc09 5.2 100 BIT-ERROR RATE (%) SUPPLY CURRENT (mA) 5.4 6.5 SUPPLY CURRENT (mA) +105°C 5.5 7.0 MAX1473 toc01 5.6 BIT-ERROR RATE vs. AVERAGE RF INPUT POWER MAX1473 toc03 SUPPLY CURRENT vs. SUPPLY VOLTAGE SYSTEM GAIN (dB) MAX1473 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range NORMALIZED IF GAIN vs. IF FREQUENCY -5 -10 MAX1473 toc12 MAX1473 toc11 MAX1473 toc10 0 S11 SMITH PLOT OF RFIN S11 MAGNITUDE-LOG PLOT OF RFIN 30 20 10 MAGNITUDE (dB) NORMALIZED IF GAIN (dB) 5 600MHz 0 -10 -20 100MHz -30 -40 -15 -50 -20 -70 315MHz -34dB -60 100 RF FREQUENCY (MHz) REGULATOR VOLTAGE vs. REGULATOR CURRENT PHASE NOISE vs. OFFSET FREQUENCY 0 MAX1473 toc13 -40°C 2.9 +25°C +85°C +105°C 2.8 2.7 2.6 VDD = 5.0V 2.5 5 15 25 35 REGULATOR CURRENT (mA) -20 PHASE NOISE (dBc/Hz) 3.0 45 fRF = 315MHz PHASE NOISE vs. OFFSET FREQUENCY 0 -40 -60 -80 -100 fRF = 433MHz -20 PHASE NOISE (dBc/Hz) 3.1 REGULATOR VOLTAGE (V) 10 109 208 307 406 505 604 703 802 901 1000 MAX1473 toc15 10 IF FREQUENCY (MHz) MAX1473 toc14 1 -40 -60 -80 -100 -120 -120 -140 1.E-05 1.E-04 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 -140 1.E-05 1.E-04 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 OFFSET FREQUENCY (MHz) OFFSET FREQUENCY (MHz) _______________________________________________________________________________________ 7 MAX1473 Typical Operating Characteristics (continued) (Typical Application Circuit, VDD = 3.3V, fRF = 315MHz, TA = +25°C, unless otherwise noted.) 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range MAX1473 Pin Description PIN 8 TSSOP QFN 1 29 2, 7 3 NAME FUNCTION XTAL1 1st Crystal Input. (See Phase-Locked Loop section.) 4, 30 AVDD Positive Analog Supply Voltage for RF Sections. (See Typical Application Circuit.) 31 LNAIN Low-Noise Amplifier Input. (See Low-Noise Amplifier section.) 4 32 LNASRC 5 2 AGND 6 3 LNAOUT 8 5 MIXIN1 9 6 MIXIN2 2nd Differential Mixer Input. Connect through a 100pF capacitor to LC tank filter from LNAOUT. 10 7 AGND Analog Ground 11 8 IRSEL Image Rejection Select Pin. Set VIRSEL = 0V to center image rejection at 315MHz. Leave IRSEL floating to center image rejection at 375MHz. Set VIRSEL = VDD to center image rejection at 433MHz. 12 9 MIXOUT 13 10 DGND Digital Ground 14 11 DVDD Positive Digital Supply Voltage. Decouple to DGND with a 0.01µF capacitor. 15 12 AGCDIS AGC Control Pin. Pull high to disable AGC. Crystal Divider Ratio Select Pin. Drive XTALSEL low to select divider ratio of 64, or drive XTALSEL high to select divider ratio of 32. Low-Noise Amplifier Source for External Inductive Degeneration. Connect inductor to ground to set LNA input impedance. (See Low-Noise Amplifier section.) Analog Ground Low-Noise Amplifier Output. Connect to mixer through an LC tank filter. (See Low-Noise Amplifier section.) 1st Differential Mixer Input. Connect through a 100pF capacitor to VDD side of the LC tank. 330Ω Mixer Output. Connect to the input of the 10.7MHz bandpass filter. 16 14 XTALSEL 17 15 IFIN1 1st Differential Intermediate Frequency Limiter Amplifier Input. Decouple to AGND with a 1500pF capacitor. 18 16 IFIN2 2nd Differential Intermediate Frequency Limiter Amplifier Input. Connect to the output of a 10.7MHz bandpass filter. 19 17 DFO Data Filter Output 20 18 DSN Negative Data Slicer Input 21 19 OPP Noninverting Op-Amp Input for the Sallen-Key Data Filter 22 20 DFFB Data Filter Feedback Node. Input for the feedback of the Sallen-Key data filter. 23 22 DSP Positive Data Slicer Input VDD5 5V Supply Voltage. VDD5 is shorted to AVDD for 3.3V operation. 24 23 25 24 26 26 PDOUT Peak Detector Output 27 27 PWRDN Power-Down Select Input. Drive this pin with a logic high to power on the IC. 28 28 XTAL2 — 1, 13, 21, 25 N.C. DATAOUT Digital Baseband Data Output 2nd Crystal Input No Connection _______________________________________________________________________________________ 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range The MAX1473 CMOS superheterodyne receiver and a few external components provide the complete receive chain from the antenna to the digital output data. Depending on signal power and component selection, data rates as high as 100kbps can be achieved. The MAX1473 is designed to receive binary ASK data modulated in the 300MHz to 450MHz frequency range. ASK modulation uses a difference in amplitude of the carrier to represent logic 0 and logic 1 data. Low-Noise Amplifier The LNA is an NMOS cascode amplifier with off-chip inductive degeneration that achieves approximately 16dB of power gain with a 2.0dB noise figure and an IIP3 of -12dBm. The gain and noise figure are dependent on both the antenna matching network at the LNA input and the LC tank network between the LNA output and the mixer inputs. The off-chip inductive degeneration is achieved by connecting an inductor from LNASRC to AGND. This inductor sets the real part of the input impedance at LNAIN, allowing for a more flexible input impedance match, such as a typical PC board trace antenna. A nominal value for this inductor with a 50Ω input impedance is 15nH, but is affected by PC board trace. See Typical Operating Characteristics for the relationship between the inductance and the LNA input impedance. The AGC circuit monitors the RSSI output. When the RSSI output reaches 2.05V, which corresponds to an RF input level of approximately -57dBm, the AGC switches on the LNA gain reduction resistor. The resistor reduces the LNA gain by 35dB, thereby reducing the RSSI output by about 500mV. The LNA resumes high-gain mode when the RSSI level drops back below 1.45V (approximately -65dBm at RF input) for 150ms. The AGC has a hysteresis of ~8dB. With the AGC function, the MAX1473 can reliably produce an ASK output for RF input levels up to 0dBm with a modulation depth of 18dB. The LC tank filter connected to LNAOUT comprises L3 and C2 (see Typical Application Circuit). Select L3 and C2 to resonate at the desired RF input frequency. The resonant frequency is given by: 1 f = 2π L TOTAL × C TOTAL where: LTOTAL = L3 + LPARASITICS CTOTAL = C2 + CPARASITICS LPARASITICS and CPARASITICS include inductance and capacitance of the PC board traces, package pins, mixer input impedance, LNA output impedance, etc. These parasitics at high frequencies cannot be ignored, and can have a dramatic effect on the tank filter center frequency. Lab experimentation should be done to optimize the center frequency of the tank. Mixer A unique feature of the MAX1473 is the integrated image rejection of the mixer. This device eliminates the need for a costly front-end SAW filter for most applications. Advantages of not using a SAW filter are increased sensitivity, simplified antenna matching, less board space, and lower cost. The mixer cell is a pair of double balanced mixers that perform an IQ downconversion of the RF input to the 10.7MHz IF from a low-side injected LO (i.e., fLO = fRF fIF). The image-rejection circuit then combines these signals to achieve a minimum 45dB of image rejection over the full temperature range. Low-side injection is required due to the on-chip image rejection architecture. The IF output is driven by a source-follower biased to create a driving impedance of 330Ω; this provides a good match to the off-chip 330Ω ceramic IF filter. The voltage conversion gain is approximately 13dB when the mixer is driving a 330Ω load. The IRSEL pin is a logic input that selects one of the three possible image-rejection frequencies. When VIRSEL = 0V, the image rejection is tuned to 315MHz. VIRSEL = VDD/2 tunes the image rejection to 375MHz, and when VIRSEL = VDD, the image rejection is tuned to 433MHz. The IRSEL pin is internally set to VDD/2 (image rejection at 375MHz) when it is left floating, thereby eliminating the need for an external VDD/2 voltage. Phase-Locked Loop The PLL block contains a phase detector, charge pump/integrated loop filter, VCO, asynchronous 64x clock divider, and crystal oscillator driver. Besides the crystal, this PLL does not require any external components. The VCO generates a low-side local oscillator (LO). The relationship between the RF, IF, and reference frequencies is given by: fREF = (fRF - fIF) / (32 ✕ M) where: M = 1 (VXTALSEL = VDD) or 2 (VXTALSEL = 0V) To allow the smallest possible IF bandwidth (for best sensitivity), the tolerance of the reference must be minimized. _______________________________________________________________________________________ 9 MAX1473 Detailed Description MAX1473 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range Intermediate Frequency/RSSI The IF section presents a differential 330Ω load to provide matching for the off-chip ceramic filter. The six internal AC-coupled limiting amplifiers produce an overall gain of approximately 65dB, with a bandpass filter-type response centered near the 10.7MHz IF frequency with a 3dB bandwidth of approximately 11.5MHz. The RSSI circuit demodulates the IF by producing a DC output proportional to the log of the IF signal level, with a slope of approximately 14.2mV/dB (see Typical Operating Characteristics). The AGC circuit monitors the RSSI output. When the RSSI output reaches 2.05V, which corresponds to an RF input level of approximately -57dBm, the AGC switches on the LNA gain reduction resistor. The resistor reduces the LNA gain by 35dB, thereby reducing the RSSI output by about 500mV. The LNA resumes high-gain mode when the RSSI level drops back below 1.45V (approximately -65dBm at RF input) for 150ms. The AGC has a hysteresis of ~8dB. With the AGC function, the MAX1473 can reliably produce an ASK output for RF input levels up to 0dBm with modulation depth of 18dB. Applications Information Crystal Oscillator The XTAL oscillator in the MAX1473 is designed to present a capacitance of approximately 3pF between the XTAL1 and XTAL2. If a crystal designed to oscillate with a different load capacitance is used, the crystal is pulled away from its stated operating frequency, introducing an error in the reference frequency. Crystals designed to operate with higher differential load capacitance always pull the reference frequency higher. For example, a 4.7547MHz crystal designed to operate with a 10pF load capacitance oscillates at 4.7563MHz with the MAX1473, causing the receiver to be tuned to 315.1MHz rather than 315.0MHz, an error of about 100kHz, or 320ppm. In actuality, the oscillator pulls every crystal. The crystal’s natural frequency is really below its specified frequency, but when loaded with the specified load capacitance, the crystal is pulled and oscillates at its specified frequency. This pulling is already accounted for in the specification of the load capacitance. Table 1. Component Values for Typical Application Circuit COMPONENT VALUE FOR 433MHz RF VALUE FOR 315MHz RF DESCRIPTION L1 56nH 110nH Toko LL1608-FH L2 15nH 15nH Murata LQP11A L3 15nH 27nH Murata LQP11A C1 100pF 100pF 5% C2 2.7pF 4.7pF ± 0.1pF C3 100pF 100pF 5% 10 C4 100pF 100pF 5% C5 1500pF 1500pF 10% C6 220pF 220pF 5% C7 470pF 470pF 5% C8 0.47µF 0.47µF 20% C9 220pF 220pF 10% C10 0.01µF 0.01µF 20% C11 0.01µF 0.01µF 20% C12 15pF 15pF Depends on XTAL C13 15pF 15pF Depends on XTAL R1 5kΩ 5kΩ 5% X1 6.6128MHz or 13.2256MHz 4.7547MHz or 9.5094MHz — X2 10.7MHz ceramic filter 10.7MHz ceramic filter Murata SFECV10.7 series ______________________________________________________________________________________ 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range where: fp is the amount the crystal frequency pulled in ppm. Cm is the motional capacitance of the crystal. Ccase is the case capacitance. Cspec is the specified load capacitance. Cload is the actual load capacitance. When the crystal is loaded as specified, i.e., Cload = Cspec, the frequency pulling equals zero. Data Filter The data filter is implemented as a 2nd-order lowpass Sallen-Key filter. The pole locations are set by the combination of two on-chip resistors and two external capacitors. Adjusting the value of the external capacitors changes the corner frequency to optimize for different data rates. The corner frequency should be set to approximately 1.5 times the fastest expected data rate from the transmitter. Keeping the corner frequency near the data rate rejects any noise at higher frequencies, resulting in an increase in receiver sensitivity. The configuration shown in Figure 1 can create a Butterworth or Bessel response. The Butterworth filter offers a very flat amplitude response in the passband and a rolloff rate of 40dB/decade for the two-pole filter. The Bessel filter has a linear phase response, which works well for filtering digital data. To calculate the value of C5 and C6, use the following equations along with the coefficients in Table 2: C5 = C6 = b ( )( )( ) a 100k π fc a ( )( )( ) 4 100k π fc where fC is the desired 3dB corner frequency. For example, choose a Butterworth filter response with a corner frequency of 5kHz: C5 = ( )( 1.000 )( )( ) 1.414 100kΩ 3.14 5kHz ≈ 450pF MAX1473 Additional pulling can be calculated if the electrical parameters of the crystal are known. The frequency pulling is given by: C 1 1 × 106 fp = m 2 Ccase + Cload Ccase + Cspec MAX1473 RSSI RDF1 100kΩ RDF2 100kΩ 22 DFFB 21 OPP 19 DFO C6 C5 Figure 1. Sallen-Key Lowpass Data Filter Choosing standard capacitor values changes C5 to 470pF and C6 to 220pF, as shown in the Typical Application Circuit. Table 2. Coefficents to Calculate C5 and C6 FILTER TYPE a b Butterworth (Q = 0.707) 1.414 1.000 Bessel (Q = 0.577) 1.3617 0.618 Data Slicer The purpose of the data slicer is to take the analog output of the data filter and convert it to a digital signal. This is achieved by using a comparator and comparing the analog input to a threshold voltage. One input is supplied by the data filter output. Both comparator inputs are accessible off chip to allow for different methods of generating the slicing threshold, which is applied to the second comparator input. The suggested data slicer configuration uses a resistor (R1) connected between DSN and DSP with a capacitor (C4) from DSN to DGND (Figure 2). This configuration averages the analog output of the filter and sets the threshold to approximately 50% of that amplitude. With this configuration, the threshold automatically adjusts as the analog signal varies, minimizing the possibility for errors in the digital data. The sizes of R1 and C4 affect how fast the threshold tracks to the analog amplitude. Be sure to keep the corner frequency of the RC circuit much lower than the lowest expected data rate. Note that a long string of zeros or 1’s can cause the threshold to drift. This configuration works best if a cod- ______________________________________________________________________________________ 11 MAX1473 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range MAX1473 MAX1473 DATA SLICER DATA SLICER 20 DSN 25 DATAOUT 19 DFO 23 DSP 25 DATAOUT 20 DSN 23 DSP R4 19 DFO R1 R3 C4 R1 R2 C4 *OPTIONAL Figure 2. Generating Data Slicer Threshold ing scheme, such as Manchester coding, which has an equal number of zeros and 1’s, is used. Figure 3. Generating Data Slicer Hysteresis To prevent continuous toggling of DATAOUT in the absence of an RF signal due to noise, hysteresis can be added to the data slicer as shown in Figure 3. MAX1473 Peak Detector The peak detector output (PDOUT), in conjunction with an external RC filter, creates a DC output voltage equal to the peak value of the data signal. The resistor provides a path for the capacitor to discharge, allowing the peak detector to dynamically follow peak changes of the data filter output voltage. For faster receiver startup, the circuit shown in Figure 4 can be used. DATA SLICER 25 DATAOUT 20 DSN 23 DSP 19 DFO 26 PDOUT 25kΩ Layout Considerations A properly designed PC board is an essential part of any RF/microwave circuit. On high-frequency inputs and outputs, use controlled-impedance lines and keep them as short as possible to minimize losses and radiation. At high frequencies, trace lengths that are on the order of λ/10 or longer act as antennas. Keeping the traces short also reduces parasitic inductance. Generally, 1in of a PC board trace adds about 20nH of parasitic inductance. The parasitic inductance can have a dramatic effect on the effective inductance of a passive component. For example, a 0.5in trace connecting a 100nH inductor adds an extra 10nH of inductance or 10%. To reduce the parasitic inductance, use wider traces and a solid ground or power plane below the signal traces. Also, use low-inductance connections to ground on all GND pins, and place decoupling capacitors close to all VDD connections. 12 47nF Figure 4. Using PDOUT for Faster Startup Chip Information TRANSISTOR COUNT: 3035 PROCESS: CMOS ______________________________________________________________________________________ 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range VDD3 C12 C13 C11 1 RF INPUT 2 C1 VDD5 X1 L1 3 4 L2 5 6 VDD3 7 L3 C3 8 C2 9 C4 10 C9 11 12 13 14 XTAL1 XTAL2 AVDD PWRDN LNAIN PDOUT MAX1473 LNASRC DATAOUT AGND VDD5 LNAOUT DSP AVDD DFFB MIXIN1 OPP MIXIN2 DSN AGND DFO IRSEL IFIN2 MIXOUT IFIN1 DGND XTALSEL DVDD AGCDIS 28 TO/FROM µP POWER DOWN DATA OUT 27 26 25 R2 24 R3 23 22 21 C7 20 19 18 17 R1 16 15 C5 X2 C6 C8 IF FILTER C10 IN OUT GND COMPONENT VALUES IN TABLE 1 ______________________________________________________________________________________ 13 MAX1473 Typical Application Circuit 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range MAX1473 Functional Diagram LNASRC 4 LNAIN AVDD VDD5 DVDD DGND AGND 14 3 AGCDIS LNAOUT 15 6 MIXIN1 MIXIN2 8 9 Q IMAGE REJECTION 2,7 3.3V REG 14 DIVIDE BY 64 VCO PHASE DETECTOR LOOP FILTER 5,10 IFIN2 18 IF LIMITING AMPS ∑ 90˚ 24 13 IFIN1 17 0˚ AUTOMATIC GAIN CONTROL LNA MIXOUT 12 IRSEL 11 ÷1 I MAX1473 RSSI DATA FILTER RDF1 100kΩ RDF2 100kΩ ÷2 CRYSTAL DRIVER 16 1 XTALSEL XTAL1 XTAL2 28 DATA SLICER POWER DOWN 27 PWRDN 25 DATAOUT 20 23 19 DSN DSP DFO 26 21 22 PDOUT OPP DFFB ______________________________________________________________________________________ 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range TSSOP4.40mm.EPS ______________________________________________________________________________________ 15 MAX1473 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) D2 0.15 C A D b CL 0.10 M C A B D2/2 D/2 PIN # 1 I.D. QFN THIN.EPS MAX1473 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range k 0.15 C B PIN # 1 I.D. 0.35x45 E/2 E2/2 CL (NE-1) X e E E2 k L DETAIL A e (ND-1) X e CL CL L L e e 0.10 C A C 0.08 C A1 A3 PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE 16, 20, 28, 32L, QFN THIN, 5x5x0.8 mm APPROVAL 16 DOCUMENT CONTROL NO. REV. 21-0140 C ______________________________________________________________________________________ 1 2 315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range COMMON DIMENSIONS EXPOSED PAD VARIATIONS NOTES: 1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994. 2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES. 3. N IS THE TOTAL NUMBER OF TERMINALS. 4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE. 5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.25 mm AND 0.30 mm FROM TERMINAL TIP. 6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY. 7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION. 8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS. PROPRIETARY INFORMATION 9. DRAWING CONFORMS TO JEDEC MO220. TITLE: PACKAGE OUTLINE 16, 20, 28, 32L, QFN THIN, 5x5x0.8 mm 10. WARPAGE SHALL NOT EXCEED 0.10 mm. APPROVAL DOCUMENT CONTROL NO. REV. 21-0140 C 2 2 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 17 © 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. MAX1473 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.)