DATE (YYMMDD) NOTICE OF REVISION (NOR) (See MIL-STD-480 for instructions) This revision described below has been authorized for the document listed. Form Approved OMB No. 0704-0188 92-10-27 Public reporting burden for this collection is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Information and Regulatory Affairs, Office of Management and Budget, Washington, DC 20503. 2. CAGE CODE 1. ORIGINATOR NAME AND ADDRESS Defense Electronics Supply Center Dayton, Ohio 45444-5277 67268 4. CAGE CODE 67268 3. NOR NO. 5962-R005-93 5. DOCUMENT NO. 5962-89876 7. REVISION LETTER 6. TITLE OF DOCUMENT (Current) New (New) A Microcircuits, Linear, Transistor Array, Monolithic Silicon 8. ECP NO. No registered users 9. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIES All 10. DESCRIPTION OF REVISION Sheet 1: Revisions ltr column; add "A". Revisions description column; add "Changes in accordance with NOR 5962-R005-93". Revisions date column; add "92-10-27". Revision level block; add "A". Rev status above sheet number 1, 2, and 6, add "A". Sheet 2: 1.2.2 Case outline; Under case outline letter column add "F", under descriptive designator column add "GDFP2-F16 or CDFP3-F16", under terminals column add "16", and under package style column add "flat pack". 1.3 Absolute maximum ratings; Delete "Thermal resistance, junction-to-ambient (JA)- - - - 80(C/W" and substitute "Thermal resistance, junction-to-ambient (JA): Case E - - - 80(C/W, Case F - - - 115(C/W". Delete "Power dissipation (PD) 1/ - - - - 1.0 W" and substitute "Power dissipation (PD): Case E - - - 1.0 W, Case F - - - 1.09 W". Under footnotes, delete "1/ Absolute maximum rating for power dissipation is for one darlington pair only. Derate 12.5 mW/(C above +25(C ambient." and substitute "1/ Absolute maximum rating for power dissipation is for one darlington pair only. Derate case outline E at 12.5 mW/(C above +25(C ambient and case outline F at 8.7 mW/(C above +25(C ambient." Revision level block; add "A". Sheet 6: Figure 1; for case outline, delete "E" and substitute "E, F". Revision level block; add "A". 11. THIS SECTION FOR GOVERNMENT USE ONLY a. CHECK ONE eXf EXISTING DOCUMENT SUPPLEMENTED BY THIS NOR MAY BE USED IN MANUFACTURE. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENT DESC-ECS e f REVISED DOCUMENT MUST BE RECEIVED BEFORE MANUFACTURER MAY INCORPORATE THIS CHANGE. SIGNATURE AND TITLE e f CUSTODIAN OF MASTER DOCUMENT SHALL MAKE ABOVE REVISION AND FURNISH REVISED DOCUMENT TO: DATE (YYMMDD) Sandra Rooney 92-10-27 for Branch Chief 12. ACTIVITY ACCOMPLISHING REVISION DESC-ECS DD Form 1695, JUL 88 REVISION COMPLETED (Signature) Marcia B Kelleher Previous editions are obsolete. DATE (YYMMDD) 92-10-27 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHEET REV SHEET REV STATUS OF SHEETS PMIC N/A STANDARDIZED MILITARY DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE REV 1 SHEET 2 3 4 PREPARED BY Dan Wonnell 5 7 8 9 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 CHECKED BY Charles E. Besore APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, TRANSISTOR ARRAY, MONOLITHIC SILICON DRAWING APPROVAL DATE 92-08-27 SIZE AMSC N/A 6 REVISION LEVEL CAGE CODE A 67268 SHEET 1 DESC FORM 193 JUL 91 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. OF 5962-89876 9 5962-E466 1. SCOPE 1.1 Scope. This drawing describes device requirements for class B microcircuits in accordance with 1.2.1 of MIL-STD-883, "Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices". 1.2 Part or Identifying Number (PIN). The complete PIN shall be as shown in the following example: 01 E X Device type (1.2.1) Case outline (1.2.2) Lead finish per MIL-M-38510 5962-89876 Drawing number 1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows: Device type 01 Generic number Circuit function 2023 7 gate darlington transistor array 1.2.2 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835, and as follows: Outline letter E Descriptive designator GDIP1-T16 or CDIP2-T16 Terminals Package style 16 Dual-in-line 1.3 Absolute maximum ratings. Output voltage (VCE) - - - - - - - - - - - - - - - - - - - - Input voltage (VIN) - - - - - - - - - - - - - - - - - - - - - - Peak output current (IOUT) - - - - - - - - - - - - - - - - Ground terminal current (IGND) - - - - - - - - - - - - Continuous input current (IIN) - - - - - - - - - - - - - - Power dissipation (PD) 1/ - - - - - - - - - - - - - - - - Storage temperature range - - - - - - - - - - - - - - - - Junction temperature (TJ) - - - - - - - - - - - - - - - - - Thermal resistance, junction-to-ambient (JA) - - - - 95 V dc 30 V dc 500 mA 3.0 A 25 mA 1.0 W -65(C to +150(C +175(C 80(C/W 1.4 Recommended operating conditions. Ambient operating temperature range (TA) - - - - - - -55(C to +125(C 1/ Absolute maximum rating for power dissipation is for one darlington pair only. Derate 12.5 mW/(C above +25(C ambient. SIZE STANDARDIAZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 5962-89876 A REVISION LEVEL SHEET 2 2. APPLICABLE DOCUMENTS 2.1 Government specification, standard, and bulletin. Unless otherwise specified, the following specification, standard, and bulletin of the issue listed in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specified herein. SPECIFICATION MILITARY MIL-M-38510 - Microcircuits, General Specification for. STANDARD MILITARY MIL-STD-883 MIL-STD-1835 - Test Methods and Procedures for Microelectronics. - Microcircuit Case Outlines. BULLETIN MILITARY MIL-BUL-103 - List of Standardized Military Drawings (SMD's). (Copies of the specification, standard, and bulletin required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing shall take precedence. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with 1.2.1 of MIL-STD-883, "Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices" and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-M-38510 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Switching test circuit and waveforms. The switching test circuit and waveforms shall be as specified on figure 2. 3.3. Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4. Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. SIZE STANDARDIAZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 5962-89876 A REVISION LEVEL SHEET 3 TABLE I. Electrical performance characteristics. Test Output leakage current Collector emitter saturation voltage Input voltage Input current Input current ICEX VCE(sat) VIN(ON) IIN(ON) IIN(OFF) Symbol Conditions -55(C TA +125(C unless otherwise specified VCE = 95 V IC = 350 mA, IB = 500 )A IC = 200 mA, IB = 350 )A IC = 100 mA, IB = 250 )A IC = 350 mA, IB = 500 )A IC = 200 mA, IB = 350 )A IC = 100 mA, IB = 250 )A IC = 350 mA, IB = 850 )A IC = 200 mA, IB = 550 )A IC = 100 mA, IB = 350 )A VCE = 2.0 V, IC = 200 mA VCE = 2.0 V, IC = 250 mA VCE = 2.0 V, IC = 300 mA VCE = 2.0 V, IC = 200 mA VCE = 2.0 V, IC = 250 mA VCE = 2.0 V, IC = 300 mA VIN = 3.85 V IC = 500 )A Group A subgroups 1,2,3 2 1 3 2 1,3 1,2,3 2 Device type 01 01 01 01 01 Limits Min Max 100 1.8 1.5 1.3 1.6 1.3 1.1 1.8 1.5 1.3 2.4 2.7 3.0 3.3 3.6 3.9 650 1350 20 Unit )A V V )A )A SIZE STANDARDIAZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 5962-89876 A REVISION LEVEL SHEET 4 TABLE I. Electrical performance characteristics - Continued. Test Clamp diode leakage current Clamp diode forward leakage Turn-on delay Turn-off delay Symbol IR VF tPHL tPLH Conditions -55(C TA +125(C unless otherwise specified VR = 95 V IF = 350 mA See figure 2 See figure 2 Group A subgroups 1,2,3 1,2,3 9,10,11 9,10,11 Device type 01 01 01 01 Limits Min Max 50 2.0 1000 1000 Unit )A V ns ns 3.5 Marking. Marking shall be in accordance with MIL-STD-883 (see 3.1 herein). The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-BUL-103 (see 6.6 herein). 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-BUL-103 (see 6.6 herein). The certificate of compliance submitted to DESC-EC prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-STD-883 (see 3.1 herein) and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-STD-883 (see 3.1 herein) shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DESC-EC shall be required in accordance with MIL-STD-883 (see 3.1 herein). 3.9 Verification and review. DESC, DESC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with section 4 of MIL-M-38510 to the extent specified in MIL-STD-883 (see 3.1 herein). 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A,B,C, or D using the circuit submitted with the certificate of compliance (see 3.6 herein). (2) TA = +125(C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. SIZE STANDARDIAZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 5962-89876 A REVISION LEVEL SHEET 5 Device type 01 Case outline E Terminal number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Terminal symbol IN1 IN2 IN3 IN4 IN5 IN6 IN7 GND COM OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 FIGURE 1. Terminal connections. SIZE STANDARDIAZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 5962-89876 A REVISION LEVEL SHEET 6 FIGURE 2. Switching test circuit and waveforms. SIZE STANDARDIAZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 5962-89876 A REVISION LEVEL SHEET 7 TABLE II. Electrical test requirements. MIL-STD-883 Test Requirements Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group A test requirements (method 5005) Groups C and D end-point electrical parameters (method 5005) Subgroups (per method 5005, table I) 1 1*, 2, 3 1, 2, 3, 9, 10, 11** 1, 2, 3 * PDA applies to subgroup 1. ** Subgroups 10 and 11, if not tested, shall be guaranteed to the specified limits in table I. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D using the circuit submitted with the certificate of compliance (see 3.6 herein). (2) TA = +125(C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. SIZE STANDARDIAZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 5962-89876 A REVISION LEVEL SHEET 8 5. PACKAGING 5.1 Packaging requirements.The requirements for packaging shall be in accordance with MIL-M-38510. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. When a military specification exists and the product covered by this drawing has been qualified for listing on QPL-38510, the device specified herein will be inactivated and will not be used for new design. The QPL-38510 product shall be the preferred item for all applications. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished in accordance with MIL-STD-481 using DD Form 1693, Engineering Change Proposal (Short Form). 6.4 Record of users. Military and industrial users shall inform Defense Electronics Supply Center when a system application requires configuration control and the applicable SMD. DESC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DESC-EC, telephone (513) 296-6047. 6.5 Comments. Comments on this drawing should be directed to DESC-EC, Dayton, Ohio 45444, or telephone (513) 296-5377. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-BUL-103. The vendors listed in MIL-BUL-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DESC-EC. SIZE STANDARDIAZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 5962-89876 A REVISION LEVEL SHEET 9 STANDARDIZED MILITARY DRAWING SOURCE APPROVAL BULLETIN DATE: 92-08-27 Approved sources of supply for SMD 5962-89876 are listed below for immediate acquisition only and shall be added to MIL-BUL-103 during the next revision. MIL-BUL-103 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DESC-EC. This bulletin is superseded by the next dated revision of MIL-BUL-103. Standardized military drawing PIN 5962-8987601EX Vendor CAGE number 31019 34333 Vendor similar PIN 1/ ULS2023H/883 or ULS2023R/883 SG2023J/883B 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number Vendor name and address 31019 Allegro Microsystems Incorporated 3900 Welsh Road Willow Grove, PA 19090-2909 34333 Silicon General 11861 Western Avenue Garden Grove, CA 92641 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in this information bulletin.