REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change for 1.3 collector-emitter voltage maximum limit. Change limits and conditions for base offset voltage, change in emitter-base offset, collector leakage, base leakage, current gain and gain match tests. 89-08-25 M. A. Frye B Drawing updated to reflect current requirements. Editorial changes throughout. – drw 01-01-16 Raymond Monnin The original first page of this drawing has been replaced. REV SHEET REV SHEET REV STATUS REV B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Joseph A. Kerby STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216 http://www.dscc.dla.mil CHECKED BY Ray Monnin APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE Michael A. Frye MICROCIRCUIT, LINEAR, TRANSISTOR ARRAYS/MATCHED PAIR, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-12-11 AMSC N/A REVISION LEVEL B SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 OF 5962-87777 9 5962-E177-01 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87777 01 X A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type. The device type identify the circuit function as follows: Device type Generic number 01 Circuit function LM194 Transistor supermatch pair 1.2.2 Case outline. The case outline is as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator X See figure 2 Terminals Package style 6 Similar to a TO-99 can 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Collector current ...................................................................... Collector-emitter voltage.......................................................... Base-emitter current ................................................................ Maximum power dissipation (PD) ............................................. Lead temperature (soldering, 60 seconds).............................. Storage temperature range...................................................... Thermal resistance, junction-to-case (TJC)............................... Thermal resistance, junction-to-case (TJA)............................... 20 mA 35 V dc r10 mA 500 mW +300 qC -65qC to +150qC 70qC/W 230qC/W 1.4 Recommended operating conditions. Ambient operating temperature range (TA).............................. -55qC to +125qC STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87777 A REVISION LEVEL B SHEET 2 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein and figure 2. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87777 A REVISION LEVEL B SHEET 3 TABLE I. Electrical performance characteristics. Test Symbol Emitter: Base offset voltage VBEO Conditions -55qC d TA d +125qC Group A subgroups Device type Limits VCB = 0 V, IC = 1 mA 1 All r100 VCB = 35 V, IC = 1 mA 1 All r100 Min VCB = 0 V, IC = 0.3 mA 1 All r100 VCB = 0 V, IC = 100 PA 1 All r100 VCB = 35 V, IC = 100 PA 1 All r100 Collector: Base leakage VCB = 0 V, IC = 10 PA 1 All r100 VCB = 35 V, IC = 10 PA 1 All r100 VCB = 0 V, IC = 1 PA 1 All r100 VCB = 35 V, IC = 1 PA 1 All r100 Delta VCB = 0 to 35 V, IC = 1 mA 1 All r25 VBEO VCB = 0 to 35 V, IC = 100 PA 1 All r25 VCB = 0 to 35 V, IC = 10 PA 1 All r25 VCB = 0 to 35 V, IC = 1 PA 1 All r25 VCB = 0 V, IC = 1 to 300 PA 1 All r25 VCB = 35 V, COLL 1 to COLL 2 1 All r2 VCB = 35 V, COLL 2 to COLL 1 1 All r2 VCB = 35 V, COLL 1 to BASE 1 1 All r0.25 VCB = 35 V, COLL 2 to BASE 2 1 All r0.25 ICCX ICBX STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 PV r350 2, 3 Collector: Collector leakage Max r350 2, 3 Change in emitter-base offset Unit PV nA nA SIZE 5962-87777 A REVISION LEVEL B SHEET 4 TABLE I. Electrical performance characteristics - continued. Test Conditions -55qC d TA d +125qC Group A subgroups Device type VCB = 0 V, IC = 1 mA 1 All 350 VCB = 35 V, IC = 1 mA 1 All 350 Symbol Limits Min Current gain hFE 2, 3 Gain match Max 250 VCB = 0 V, IC = 100 PA 1 All 350 VCB = 35 V, IC = 100 PA 1 All 350 VCB = 0 V, IC = 10 PA 1 All 300 VCB = 35 V, IC = 10 PA 1 All 300 VCB = 0 V, IC = 1 PA 1 All 200 VCB = 35 V, IC = 1 PA 1 All 200 hFE VCB = 0 V, IC = 1 mA 4 All r2 match VCB = 35 V, IC = 1 mA 4 All r2 VCB = 0 V, IC = 100 PA 4 All r2 VCB = 35 V, IC = 100 PA 4 All r2 VCB = 0 V, IC = 10 PA 4 All r2 VCB = 35 V, IC = 10 PA 4 All r2 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 % r6 5, 6 DSCC FORM 2234 APR 97 Unit SIZE 5962-87777 A REVISION LEVEL B SHEET 5 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535, appendix A. 3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Device type 01 Case outline X Terminal number Terminal symbol 1 Collector 2 Base 3 Emitter 4 Emitter 5 Base 6 Collector FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87777 A REVISION LEVEL B SHEET 6 Inches Symbol Millimeters Min Max Min Max A 0.165 0.185 4.191 4.699 b D D1 0.015 0.016 0.381 0.406 0.350 0.370 8.890 9.398 0.315 0.335 8.001 8.509 e 0.195 0.205 4.953 5.207 e1 0.120 0.140 3.048 F 0.035 3.556 0.889 k 0.028 0.034 0.711 0.864 k1 0.029 0.045 0.737 1.143 L 0.500 L1 L2 12.700 0.025 0.015 0.635 0.040 0.318 1.016 FIGURE 2. Case outline X. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87777 A REVISION LEVEL B SHEET 7 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TA = +125qC, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group A test requirements (method 5005) Groups C and D end-point electrical parameters (method 5005) --1*, 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6 1, 2, 3 * PDA applies to subgroup 1. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87777 A REVISION LEVEL B SHEET 8 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. (2) TA = +125qC, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone (614) 692-0674. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MILHDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87777 A REVISION LEVEL B SHEET 9 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 01-01-16 Approved sources of supply for SMD 5962-87777 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-8777701XA 27014 LM194H/883 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number 27014 Vendor name and address National Semiconductor 2900 Semiconductor Dr PO Box 58090 Santa Clara, CA 95052-8090 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.