MAXIM MAX12527ETK

19-3543; Rev 0; 2/05
KIT
ATION
EVALU
E
L
B
AVAILA
Dual, 65Msps, 12-Bit, IF/Baseband ADC
Features
The MAX12527 is a dual 3.3V, 12-bit analog-to-digital
converter (ADC) featuring fully differential wideband
track-and-hold (T/H) inputs, driving internal quantizers.
The MAX12527 is optimized for low power, small size,
and high dynamic performance in intermediate frequency (IF) and baseband sampling applications. This dual
ADC operates from a single 3.3V supply, consuming
only 620mW while delivering a typical 69.8dB signal-tonoise ratio (SNR) performance at a 175MHz input frequency. The T/H input stages accept single-ended or
differential inputs up to 400MHz. In addition to low operating power, the MAX12527 features a 166µW powerdown mode to conserve power during idle periods.
A flexible reference structure allows the MAX12527 to
use the internal 2.048V bandgap reference or accept
an externally applied reference and allows the reference to be shared between the two ADCs. The reference structure allows the full-scale analog input range
to be adjusted from ±0.35V to ±1.15V. The MAX12527
provides a common-mode reference to simplify design
and reduce external component count in differential
analog input circuits.
The MAX12527 supports either a single-ended or differential input clock. User-selectable divide-by-two (DIV2)
and divide-by-four (DIV4) modes allow for design flexibility and help eliminate the negative effects of clock jitter.
Wide variations in the clock duty cycle are compensated
with the ADC’s internal duty-cycle equalizer (DCE).
The MAX12527 features two parallel, 12-bit-wide,
CMOS-compatible outputs. The digital output format is
pin-selectable to be either two’s complement or Gray
code. A separate power-supply input for the digital outputs accepts a 1.7V to 3.6V voltage for flexible interfacing with various logic levels. The MAX12527 is available
in a 10mm x 10mm x 0.8mm, 68-pin thin QFN package
with exposed paddle (EP), and is specified for the
extended (-40°C to +85°C) temperature range.
For a 14-bit, pin-compatible version of this ADC, refer to
the MAX12557 data sheet.
♦ Direct IF Sampling Up to 400MHz
♦ Excellent Dynamic Performance
70.4dB/69.8dB SNR at fIN = 70MHz/175MHz
84.4dBc/80.2dBc SFDR at fIN = 70MHz/175MHz
♦ 3.3V Low Power Operation
647mW (Differential Clock Mode)
620mW (Single-Ended Clock Mode)
♦ Fully Differential or Single-Ended Analog Input
♦ Adjustable Differential Analog Input Voltage
♦ 750MHz Input Bandwidth
♦ Adjustable, Internal or External, Shared Reference
♦ Differential or Single-Ended Clock
♦ Accepts 25% to 75% Clock Duty Cycle
♦ User-Selectable DIV2 and DIV4 Clock Modes
♦ Power-Down Mode
♦ CMOS Outputs in Two’s Complement or Gray
Code
♦ Out-of-Range and Data-Valid Indicators
♦ Small, 68-Pin Thin QFN Package
♦ 14-Bit Compatible Version Available (MAX12557)
♦ Evaluation Kit Available (Order MAX12527 EV Kit)
Applications
IF and Baseband Communication Receivers
Cellular, LMDS, Point-to-Point Microwave,
MMDS, HFC, WLAN
I/Q Receivers
Ultrasound and Medical Imaging
Portable Instrumentation
Digital Set-Top Boxes
Ordering Information
PART
TEMP RANGE
MAX12527ETK
-40°C to +85°C
PIN-PACKAGE
68 Thin QFN-EP*
(10mm x 10mm x 0.8mm)
*EP = Exposed paddle.
Selector Guide
SAMPLING RATE
(Msps)
RESOLUTION
(Bits)
MAX12557
65
14
MAX12527
65
12
PART
Pin Configuration appears at end of data sheet.
Low-Power Data Acquisition
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX12527
General Description
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
ABSOLUTE MAXIMUM RATINGS
VDD to GND ................................................................-0.3V to +3.6V
OVDD to GND............-0.3V to the lower of (VDD + 0.3V) and +3.6V
INAP, INAN to GND ...-0.3V to the lower of (VDD + 0.3V) and +3.6V
INBP, INBN to GND ...-0.3V to the lower of (VDD + 0.3V) and +3.6V
CLKP, CLKN to
GND ........................-0.3V to the lower of (VDD + 0.3V) and +3.6V
REFIN, REFOUT
to GND ..................-0.3V to the lower of (VDD + 0.3V) and +3.6V
REFAP, REFAN,
COMA to GND ......-0.3V to the lower of (VDD + 0.3V) and +3.6V
REFBP, REFBN,
COMB to GND ......-0.3V to the lower of (VDD + 0.3V) and +3.6V
DIFFCLK/SECLK, G/T, PD, SHREF, DIV2,
DIV4 to GND .........-0.3V to the lower of (VDD + 0.3V) and +3.6V
D0A–D11A, D0B–D11B, DAV,
DORA, DORB to GND..............................-0.3V to (OVDD + 0.3V)
Continuous Power Dissipation (TA = +70°C)
68-Pin Thin QFN 10mm x 10mm x 0.8mm
(derate 70mW/°C above +70°C) ....................................4000mW
Operating Temperature Range................................-40°C to +85°C
Junction Temperature ...........................................................+150°C
Storage Temperature Range .................................-65°C to +150°C
Lead Temperature (soldering 10s).......................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference), CL ≈ 10pF at digital outputs, VIN = -0.5dBFS (differential), DIFFCLK/SECLK = OVDD, PD = GND, SHREF = GND, DIV2 = GND, DIV4 = GND, G/T = GND, fCLK = 65MHz, TA = -40°C to
+85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DC ACCURACY
Resolution
12
Bits
Integral Nonlinearity
INL
fIN = 3MHz
±0.3
±1.1
Differential Nonlinearity
DNL
fIN = 3MHz, no missing codes
±0.3
±0.65
LSB
±0.1
±0.7
%FSR
±0.5
±5.7
±0.5
±3.4
Offset Error
Gain Error
(Note 2)
LSB
%FSR
ANALOG INPUT (INAP, INAN, INBP, INBN)
Differential Input Voltage Range
VDIFF
Differential or single-ended inputs
±1.024
Common-Mode Input Voltage
Analog Input Resistance
RIN
CPAR
Each input (Figure 3)
Fixed capacitance to ground,
each input (Figure 3)
V
VDD / 2
V
3.4
kΩ
2
pF
Analog Input Capacitance
CSAMPLE
Switched capacitance,
each input (Figure 3)
4.5
CONVERSION RATE
Maximum Clock Frequency
fCLK
65
MHz
Minimum Clock Frequency
5
Data Latency
Figure 5
MHz
8
Clock
Cycles
dBFS
DYNAMIC CHARACTERISTICS (differential inputs)
Small-Signal Noise Floor
Signal-to-Noise Ratio
SSNF
SNR
Input at -35dBFS (Note 2)
67.0
71.1
fIN = 3MHz at -0.5dBFS
68.2
70.8
fIN = 32.5MHz at -0.5dBFS
70.6
fIN = 70MHz at -0.5dBFS
70.4
fIN = 175MHz at -0.5dBFS
2
67.2
69.8
_______________________________________________________________________________________
dB
Dual, 65Msps, 12-Bit, IF/Baseband ADC
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference), CL ≈ 10pF at digital outputs, VIN = -0.5dBFS (differential), DIFFCLK/SECLK = OVDD, PD = GND, SHREF = GND, DIV2 = GND, DIV4 = GND, G/T = GND, fCLK = 65MHz, TA = -40°C to
+85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
fIN = 3MHz at -0.5dBFS
Signal-to-Noise Plus Distortion
Spurious-Free Dynamic Range
SINAD
SFDR
THD
70.4
fIN = 70MHz at -0.5dBFS
70.2
fIN = 175MHz at -0.5dBFS
65.9
fIN = 3MHz at -0.5dBFS (Note 2)
81.9
HD2
fIN = 70MHz at -0.5dBFS
84.4
Third Harmonic
HD3
Two-Tone Intermodulation
Distortion (Note 3)
3rd-Order Intermodulation
Distortion
Two-Tone Spurious-Free
Dynamic Range
Full-Power Bandwidth
TTIMD
IM3
SFDRTT
FPBW
Aperture Delay
tAD
Aperture Jitter
tAJ
-92.6
fIN = 32.5MHz at -0.5dBFS
-84.3
fIN = 70MHz at -0.5dBFS
-83.7
fIN = 175MHz at -0.5dBFS
-78.9
Output Noise
nOUT
-91.7
fIN = 70MHz at -0.5dBFS
-94.5
fIN = 175MHz at -0.5dBFS
-80.2
-82.9
dBc
-69.8
dBc
-97
fIN = 32.5MHz at -0.5dBFS
-86.3
fIN = 70MHz at -0.5dBFS
-84.4
fIN = 175MHz at -0.5dBFS
-85.6
fIN1 = 68.5MHz at -7dBFS
fIN2 = 71.5MHz at -7dBFS
-89
fIN1 = 172.5MHz at -7dBFS
fIN2 = 177.5MHz at -7dBFS
-82.2
fIN1 = 68.5MHz at -7dBFS
fIN2 = 71.5MHz at -7dBFS
-92.2
fIN1 = 172.5MHz at -7dBFS
fIN2 = 177.5MHz at -7dBFS
-88.9
fIN1 = 68.5MHz at -7dBFS
fIN2 = 71.5MHz at -7dBFS
90.6
fIN1 = 172.5MHz at -7dBFS
fIN2 = 177.5MHz at -7dBFS
82.9
Input at -0.2dBFS, -3dB rolloff
750
INAP = INAN = COMA
INBP = INBN = COMB
dBc
-98
fIN = 32.5MHz at -0.5dBFS
Figure 5
dB
80.2
fIN = 3MHz at -0.5dBFS (Note 2)
fIN = 3MHz at -0.5dBFS
UNITS
91
86.3
71.1
MAX
69.3
fIN = 32.5MHz at -0.5dBFS
fIN = 3MHz at -0.5dBFS
Second Harmonic
TYP
70.7
fIN = 32.5MHz at -0.5dBFS
fIN = 175MHz at -0.5dBFS
Total Harmonic Distortion
MIN
68.1
dBc
dBc
dBc
dBc
MHz
1.2
ns
<0.15
psRMS
0.3
LSBRMS
_______________________________________________________________________________________
3
MAX12527
ELECTRICAL CHARACTERISTICS (continued)
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
ELECTRICAL CHARACTERISTICS (continued)
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference), CL ≈ 10pF at digital outputs, VIN = -0.5dBFS (differential), DIFFCLK/SECLK = OVDD, PD = GND, SHREF = GND, DIV2 = GND, DIV4 = GND, G/T = GND, fCLK = 65MHz, TA = -40°C to
+85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Overdrive Recovery Time
CONDITIONS
MIN
TYP
±10% beyond full-scale
1
fINA or fINB = 70MHz at -0.5dBFS
90
fINA or fINB = 175MHz at -0.5dBFS
85
MAX
UNITS
Clock
cycle
INTERCHANNEL CHARACTERISTICS
Crosstalk Rejection
Gain Matching
±0.01
Offset Matching
±0.01
dB
±0.1
dB
%FSR
INTERNAL REFERENCE (REFOUT)
REFOUT Output Voltage
VREFOUT
REFOUT Load Regulation
REFOUT Temperature Coefficient
2.000
-1mA < IREFOUT < +1mA
TCREF
REFOUT Short-Circuit Current
2.048
2.080
V
35
mV/mA
±50
ppm/°C
Short to VDD—sinking
0.24
Short to GND—sourcing
2.1
mA
BUFFERED REFERENCE MODE (REFIN is driven by REFOUT or an external 2.048V single-ended reference source;
VREFAP/VREFAN/VCOMA and VREFBP/VREFBN/VCOMB are generated internally)
REFIN Input Voltage
VREFIN
2.048
V
REFIN Input Resistance
RREFIN
>50
MΩ
COM_ Output Voltage
VCOMA
VCOMB
VDD / 2
REF_P Output Voltage
VREFAP
VREFBP
VDD / 2 + (VREFIN x 3/8)
2.418
V
REF_N Output Voltage
VREFAN
VREFBN
VDD / 2 - (VREFIN x 3/8)
0.882
V
Differential Reference Voltage
VREFA
VREFB
Differential Reference
Temperature Coefficient
TCREF
VREFA = VREFAP - VREFAN
VREFB = VREFBP - VREFBN
1.60
1.440
1.65
1.536
±25
1.70
V
1.590
V
ppm/°C
UNBUFFERED EXTERNAL REFERENCE (REFIN = GND, VREFAP/VREFAN/VCOMA and VREFBP/VREFBN/VCOMB are applied
externally, VCOMA = VCOMB = VDD / 2)
REF_P Input Voltage
VREFAP
VREFBP
VREF_P - VCOM
+0.768
V
REF_N Input Voltage
VREFAN
VREFBN
VREF_N - VCOM
-0.768
V
COM_ Input Voltage
VCOM
VDD / 2
1.65
V
Differential Reference Voltage
VREFA
VREFB
VREF_ = VREF_P - VREF_N = VREFIN x 3/4
1.536
V
4
_______________________________________________________________________________________
Dual, 65Msps, 12-Bit, IF/Baseband ADC
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference), CL ≈ 10pF at digital outputs, VIN = -0.5dBFS (differential), DIFFCLK/SECLK = OVDD, PD = GND, SHREF = GND, DIV2 = GND, DIV4 = GND, G/T = GND, fCLK = 65MHz, TA = -40°C to
+85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
REF_P Sink Current
IREFAP
IREFBP
VREF_P = 2.418V
1.2
mA
REF_N Source Current
IREFAN
IREFBN
VREF_N = 0.882V
0.85
mA
COM_ Sink Current
ICOMA
ICOMB
VCOM_ = 1.65V
0.85
mA
REF_P, REF_N Capacitance
CREF_P,
CREF_N
13
pF
COM_ Capacitance
CCOM_
6
pF
CLOCK INPUTS (CLKP, CLKN)
Single-Ended Input High
Threshold
Single-Ended Input Low
Threshold
VIH
DIFFCLK/SECLK = GND, CLKN = GND
VIL
DIFFCLK/SECLK = GND, CLKN = GND
0.8 x
VDD
V
0.2 x
VDD
V
Minimum Differential Clock Input
Voltage Swing
DIFFCLK/SECLK = OVDD
0.2
VP-P
Differential Input Common-Mode
Voltage
DIFFCLK/SECLK = OVDD
VDD / 2
V
CLK_ Input Resistance
RCLK
Each input (Figure 4)
5
kΩ
CLK_ Input Capacitance
CCLK
Each input
2
pF
DIGITAL INPUTS (DIFFCLK/SECLK, G/T, PD, DIV2, DIV4)
Input High Threshold
VIH
Input Low Threshold
VIL
V
0.2 x
OVDD
±5
OVDD applied to input
Input Leakage Current
Digital Input Capacitance
0.8 x
OVDD
Input connected to ground
±5
CDIN
5
V
µA
pF
DIGITAL OUTPUTS (D0A–D11A, D0B–D11B, DORA, DORB, DAV)
Output-Voltage Low
VOL
D0A–D11A, D0B–D11B, DORA, DORB:
ISINK = 200µA
0.2
DAV: ISINK = 600µA
Output-Voltage High
Tri-State Leakage Current
(Note 4)
VOH
ILEAK
V
0.2
D0A–D11A, D0B–D11B, DORA, DORB:
ISOURCE = 200µA
OVDD 0.2
DAV: ISOURCE = 600µA
OVDD 0.2
V
OVDD applied to input
±5
Input connected to ground
±5
µA
_______________________________________________________________________________________
5
MAX12527
ELECTRICAL CHARACTERISTICS (continued)
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
ELECTRICAL CHARACTERISTICS (continued)
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference), CL ≈ 10pF at digital outputs, VIN = -0.5dBFS (differential), DIFFCLK/SECLK = OVDD, PD = GND, SHREF = GND, DIV2 = GND, DIV4 = GND, G/T = GND, fCLK = 65MHz, TA = -40°C to
+85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
D0A–D11A, DORA,
D0B–D11B and DORB Tri-State
Output Capacitance (Note 4)
COUT
3
pF
DAV Tri-State Output
Capacitance (Note 4)
CDAV
6
pF
POWER REQUIREMENTS
Analog Supply Voltage
Digital Output Supply Voltage
Analog Supply Current
Analog Power Dissipation
Digital Output Supply Current
6
VDD
OVDD
IVDD
PVDD
IOVDD
3.15
3.30
3.60
V
1.70
2.0
VDD
V
Normal operating mode
fIN = 175MHz at -0.5dBFS,
single-ended clock
(DIFFCLK/SECLK = GND)
188
Normal operating mode
fIN = 175MHz at -0.5dBFS
differential clock
(DIFFCLK/SECLK = OVDD)
196
Power-down mode (PD = OVDD)
clock idle
0.05
Normal operating mode
fIN = 175MHz at -0.5dBFS
single-ended clock
(DIFFCLK/SECLK = GND)
620
Normal operating mode
fIN = 175MHz at -0.5dBFS
differential clock
(DIFFCLK/SECLK = OVDD)
647
mA
215
mW
Power-down mode (PD = OVDD)
clock idle
0.165
Normal operating mode
fIN = 175MHz at -0.5dBFS
19.7
Power-down mode (PD = OVDD)
clock idle
0.001
710
mA
_______________________________________________________________________________________
Dual, 65Msps, 12-Bit, IF/Baseband ADC
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference), CL ≈ 10pF at digital outputs, VIN = -0.5dBFS (differential), DIFFCLK/SECLK = OVDD, PD = GND, SHREF = GND, DIV2 = GND, DIV4 = GND, G/T = GND, fCLK = 65MHz, TA = -40°C to
+85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
TIMING CHARACTERISTICS (Figure 5)
Clock Pulse-Width High
tCH
7.7
ns
Clock Pulse-Width Low
tCL
7.7
ns
tDAV
5.4
ns
Data-Valid Delay
Data Setup Time Before Rising
Edge of DAV
tSETUP
(Note 5)
7.0
ns
Data Hold Time After Rising Edge
of DAV
tHOLD
(Note 5)
7.0
ns
Wake-Up Time from Power-Down
tWAKE
VREFIN = 2.048V
10
ms
Note 1: Specifications ≥+25°C guaranteed by production test, <+25°C guaranteed by design and characterization.
Note 2: Specifications guaranteed by production test for ≥+25°C.
Note 3: Two-tone intermodulation distortion measured with respect to a single-carrier amplitude, and not the peak-to-average input
power of both input tones.
Note 4: During power-down, D0A–D11A, D0B–D11B, DORA, DORB, and DAV are high impedance.
Note 5: Guaranteed by design and characterization.
Typical Operating Characteristics
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference mode), CL ≈ 5pF at digital outputs, VIN = -0.5dBFS,
DIFFCLK/SECLK = OVDD, PD = GND, G/T = GND, fCLK = 65MHz (50% duty cycle), TA = +25°C, unless otherwise noted.)
-60
-80
HD3
HD2
-120
5
-70
-80
HD3
HD2
-90
-100
-110
-120
-100
0
-40
-50
-60
10
15
20
25
30
ANALOG INPUT FREQUENCY (MHz)
35
fCLK = 65.00352MHz
fIN = 70.00852MHz
AIN = -0.506dBFS
SNR = 70.1dB
SINAD = 69.8dB
THD = -82.1dBc
SFDR = 82.4dBc
-20
-30
-40
-50
-60
-70
-80
MAX12527 toc03
FFT PLOT (32,768-POINT DATA RECORD)
0
-10
AMPLITUDE (dBFS)
-40
fCLK = 65.00352MHz
fIN = 32.40059MHz
AIN = -0.506dBFS
SNR = 70.5dB
SINAD = 70.2dB
THD = -86.9dBc
SFDR = 88.7dBc
-20
-30
AMPLITUDE (dBFS)
AMPLITUDE (dBFS)
-20
MAX12527 toc01
fCLK = 65MHz
fIN = 3.00125MHz
AIN = -0.53dBFS
SNR = 71dB
SINAD = 70.9dB
THD = -94dBc
SFDR = 93.6dBc
FFT PLOT (32,768-POINT DATA RECORD)
0
-10
MAX12527 toc02
FFT PLOT (16,384-POINT DATA RECORD)
0
HD3
HD2
-90
-100
-110
-120
0
5
10
15
20
25
ANALOG INPUT FREQUENCY (MHz)
30
0
5
10
15
20
25
30
ANALOG INPUT FREQUENCY (MHz)
_______________________________________________________________________________________
7
MAX12527
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics (continued)
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference mode), CL ≈ 5pF at digital outputs, VIN = -0.5dBFS,
DIFFCLK/SECLK = OVDD, PD = GND, G/T = GND, fCLK = 65MHz (50% duty cycle), TA = +25°C, unless otherwise noted.)
TWO-TONE IMD PLOT
(16,384-POINT DATA RECORD)
HD3
-100
-110
-120
2fIN2 + fIN1
-80
-100
5
10
15
20
25
MAX12527 toc06
-60
fIN2
fIN2 - fIN1
fIN1 + fIN2
-80
-120
30
0
5
10
15
20
25
30
0
5
10
15
20
25
30
ANALOG INPUT FREQUENCY (MHz)
INTEGRAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
DIFFERENTIAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
SNR, SINAD vs. ANALOG INPUT FREQUENCY
(fCLK = 65.00352MHz, AIN = -0.5dBFS)
0.3
0.1
0.1
-0.1
68
66
0
-0.1
64
62
58
-0.2
56
-0.3
-0.3
54
-0.4
-0.4
52
-0.5
-0.5
1200 1800 2400 3000 3600 4200
SINAD
60
-0.2
600
SNR
70
SNR, SINAD (dB)
0.2
DNL (LSB)
0.2
0
fCLK = 65MHz
fIN = 3.00119MHz
0.4
72
MAX12527 toc08
0.3
0.5
MAX12527 toc07
fCLK = 65MHz
fIN = 3.00119MHz
MAX12527 toc09
ANALOG INPUT FREQUENCY (MHz)
0.4
0
fIN1
ANALOG INPUT FREQUENCY (MHz)
0.5
50
0
600
0
1200 1800 2400 3000 3600 4200
50
100 150 200 250 300 350 400
DIGITAL OUTPUT CODE
DIGITAL OUTPUT CODE
fIN (MHz)
-THD, SFDR vs. ANALOG INPUT FREQUENCY
(fCLK = 65.00352MHz, AIN = -0.5dBFS)
SNR, SINAD vs. ANALOG INPUT AMPLITUDE
(fCLK = 65.00352MHz, fIN = 70MHz)
-THD, SFDR vs. ANALOG INPUT AMPLITUDE
(fCLK = 65.00352MHz, fIN = 70MHz)
SFDR
80
75
70
-THD
65
60
55
45
SINAD
35
25
50
100 150 200 250 300 350 400
fIN (MHz)
SFDR
75
65
55
-THD
35
25
15
0
85
45
55
50
MAX12527 toc12
SNR
65
95
-THD, SFDR (dBc)
85
SNR, SINAD (dB)
90
75
MAX12527 toc10
95
8
-40
-100
-120
0
INL (LSB)
-60
fCLK = 65.00352MHz
fIN1 = 172.50293MHz
AIN1 = -6.99dBFS
fIN2 = 177.40198MHz
AIN2 = -7.01dBFS
IM3 = -88.88dBc
IMD = -82.24dBc
-20
AMPLITUDE (dBFS)
HD2
-70
-80
-90
fIN2
fIN1
-40
0
MAX12527 toc11
AMPLITUDE (dBFS)
-60
fCLK = 65.00352MHz
fIN1 = 68.49889MHz
fIN2 = 71.49832MHz
AIN1 = -6.96dBFS
AIN2 = -7.02dBFS
IM3 = -92.25dBc
IMD = -89.08dBc
-20
AMPLITUDE (dBFS)
fCLK = 65.00352MHz
fIN = 174.90525MHz
AIN = -0.448dBFS
SNR = 69.4dB
SINAD = 68.9dB
THD = -78.6dBc
SFDR = 81.1dBc
-40
-50
0
MAX12527 toc04
0
-10
-20
-30
TWO-TONE IMD PLOT
(16,384-POINT DATA RECORD)
MAX12527 toc05
FFT PLOT (32,768-POINT DATA RECORD)
-THD, SFDR (dBc)
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
-55 -50 -45 -40 -35 -30 -25 -20 -15 -10 -5
AIN (dBFS)
0
-55 -50 -45 -40 -35 -30 -25 -20 -15 -10 -5
AIN (dBFS)
_______________________________________________________________________________________
0
Dual, 65Msps, 12-Bit, IF/Baseband ADC
45
SINAD
35
55
-THD
64
0
-55 -50 -45 -40 -35 -30 -25 -20 -15 -10 -5
20
0
25
30
35
40
45
50
55
60
AIN (dBFS)
AIN (dBFS)
fCLK (MHz)
-THD, SFDR vs. CLOCK SPEED
(fIN = 70MHz, AIN = -0.5dBFS)
SNR, SINAD vs. CLOCK SPEED
(fIN = 175MHz, AIN = -0.5dBFS)
-THD, SFDR vs. CLOCK SPEED
(fIN = 175MHz, AIN = -0.5dBFS)
SNR, SINAD (dB)
-THD
75
70
65
68
SINAD
66
64
62
60
30
35
40
45
50
55
60
65
80
75
-THD
70
65
60
25
SFDR
85
65
MAX12527 toc18
SNR
70
-THD, SFDR (dBc)
85
90
MAX12527 toc17
SFDR
80
72
MAX12527 toc16
90
20
66
60
25
-55 -50 -45 -40 -35 -30 -25 -20 -15 -10 -5
SINAD
68
62
35
15
60
20
25
30
35
40
45
50
55
60
65
20
25
30
35
40
45
50
55
60
65
fCLK (MHz)
fCLK (MHz)
fCLK (MHz)
SNR, SINAD vs. ANALOG SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 70MHz)
-THD, SFDR vs. ANALOG SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 70MHz)
SNR, SINAD vs. ANALOG SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 175MHz)
85
-THD, SFDR (dBc)
70
SFDR
SINAD
66
64
62
80
-THD
75
70
3.1
3.2
3.3
VDD (V)
3.4
3.5
3.6
68
SINAD
66
64
60
60
3.0
SNR
70
62
65
60
72
MAX12527 toc21
SNR
68
90
MAX12527 toc19
72
SNR, SINAD (dB)
-THD, SFDR (dBc)
65
45
25
SNR, SINAD (dB)
MAX12527 toc14
SFDR
75
SNR
70
SNR, SINAD (dB)
55
72
MAX12527 toc20
SNR, SINAD (dB)
85
-THD, SFDR (dBc)
SNR
65
95
MAX12527 toc13
75
SNR, SINAD vs. CLOCK SPEED
(fIN = 70MHz, AIN = -0.5dBFS)
-THD, SFDR vs. ANALOG INPUT AMPLITUDE
(fCLK = 65.00352MHz, fIN = 175MHz)
MAX12527 toc15
SNR, SINAD vs. ANALOG INPUT AMPLITUDE
(fCLK = 65.00352MHz, fIN = 175MHz)
3.0
3.1
3.2
3.3
VDD (V)
3.4
3.5
3.6
3.0
3.1
3.2
3.3
3.4
3.5
3.6
VDD (V)
_______________________________________________________________________________________
9
MAX12527
Typical Operating Characteristics (continued)
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference mode), CL ≈ 5pF at digital outputs, VIN = -0.5dBFS,
DIFFCLK/SECLK = OVDD, PD = GND, G/T = GND, fCLK = 65MHz (50% duty cycle), TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference mode), CL ≈ 5pF at digital outputs, VIN = -0.5dBFS,
DIFFCLK/SECLK = OVDD, PD = GND, G/T = GND, fCLK = 65MHz (50% duty cycle), TA = +25°C, unless otherwise noted.)
75
-THD
70
70
65
68
SINAD
66
64
3.1
3.2
3.3
3.4
3.5
3.6
80
-THD
75
70
65
60
3.0
SFDR
85
62
60
60
1.5
1.8
2.1
2.4
2.7
3.0
3.3
3.6
1.5
1.8
2.1
2.4
2.7
3.0
3.3
3.6
VDD (V)
OVDD (V)
OVDD (V)
SNR, SINAD vs. DIGITAL SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 175MHz)
-THD, SFDR vs. DIGITAL SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 175MHz)
PDISS, IVDD (ANALOG) vs. ANALOG SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 175MHz)
68
SINAD
66
64
SFDR
800
80
75
-THD
70
MAX12527 toc27
85
-THD, SFDR (dBc)
70
900
PDISS (ANALOG)
700
PDISS, IVDD (mW, mA)
SNR
MAX12527 toc26
90
MAX12527 toc25
72
SNR, SINAD (dB)
90
-THD, SFDR (dBc)
80
-THD, SFDR vs. DIGITAL SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 70MHz)
MAX12527 toc23
SFDR
SNR
SNR, SINAD (dB)
-THD, SFDR (dBc)
85
72
MAX12527 toc22
90
SNR, SINAD vs. DIGITAL SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 70MHz)
MAX12527 toc24
-THD, SFDR vs. ANALOG SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 175MHz)
600
500
400
IVDD
300
200
62
65
100
60
1.5
1.8
2.1
2.4
2.7
3.0
3.3
3.6
0
1.5
1.8
2.1
2.4
2.7
3.0
3.3
3.6
3.0
3.1
3.2
3.3
3.4
3.5
OVDD (V)
OVDD (V)
VDD (V)
PDISS, IOVDD (DIGITAL) vs. DIGITAL SUPPLY VOLTAGE
(fCLK = 65.00352MHz, fIN = 175MHz)
SNR, SINAD vs. CLOCK DUTY CYCLE
(fIN = 70MHz, AIN = -0.5dBFS)
-THD, SFDR vs. CLOCK DUTY CYCLE
(fIN = 70MHz, AIN = -0.5dBFS)
CL ≈ 5pF
70
90
MAX12527 toc29
72
MAX12527 toc28
80
SNR
70
3.6
SFDR
85
MAX12527 toc30
60
50
PDISS (DIGITAL)
40
30
IOVDD
68
-THD, SFDR (dBc)
60
SNR, SINAD (dB)
PDISS, IOVDD (mW, mA)
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
SINAD
66
64
80
-THD
75
70
20
62
10
60
0
1.5
1.8
2.1
2.4
2.7
OVDD (V)
10
65
SINGLE-ENDED CLOCK INPUT DRIVE
3.0
3.3
3.6
SINGLE-ENDED CLOCK INPUT DRIVE
60
25
35
45
55
CLOCK DUTY CYCLE (%)
65
75
25
35
45
55
CLOCK DUTY CYCLE (%)
______________________________________________________________________________________
65
75
Dual, 65Msps, 12-Bit, IF/Baseband ADC
SNR, SINAD vs. TEMPERATURE
(fIN = 175MHz, AIN = -0.5dBFS)
70
-THD, SFDR (dBc)
68
85
SINAD
66
64
62
SFDR
80
75
-THD
70
65
60
60
-40
-15
10
35
60
85
-40
-15
TEMPERATURE (°C)
10
35
60
85
TEMPERATURE (°C)
OFFSET ERROR vs. TEMPERATURE
GAIN ERROR vs. TEMPERATURE
0.2
OFFSET ERROR (% FSR)
2
1
0
-1
MAX12527 toc34
0.3
MAX12527 toc33
3
GAIN ERROR (%FSR)
MAX12527 toc32
SNR
SNR, SINAD (dB)
90
MAX12527 toc31
72
-THD, SFDR vs. TEMPERATURE
(fIN = 175MHz, AIN = -0.5dBFS)
0.1
0
-0.1
-0.2
-2
-0.3
-3
-40
-15
10
35
TEMPERATURE (°C)
60
85
-40
-15
10
35
60
85
TEMPERATURE (°C)
______________________________________________________________________________________
11
MAX12527
Typical Operating Characteristics (continued)
(VDD = 3.3V, OVDD = 2.0V, GND = 0, REFIN = REFOUT (internal reference mode), CL ≈ 5pF at digital outputs, VIN = -0.5dBFS,
DIFFCLK/SECLK = OVDD, PD = GND, G/T = GND, fCLK = 65MHz (50% duty cycle), TA = +25°C, unless otherwise noted.)
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
Pin Description
PIN
NAME
1, 4, 5, 9,
13, 14, 17
GND
Converter Ground. Connect all ground pins and the exposed paddle (EP) together.
2
INAP
Channel A Positive Analog Input
3
INAN
Channel A Negative Analog Input
6
COMA
Channel A Common-Mode Voltage I/O. Bypass COMA to GND with a 0.1µF capacitor.
REFAP
Channel A Positive Reference I/O. Channel A conversion range is ±2/3 x (VREFAP - VREFAN). Bypass
REFAP with a 0.1µF capacitor to GND. Connect a 10µF and a 1µF bypass capacitor between REFAP
and REFAN. Place the 1µF REFAP-to-REFAN capacitor as close to the device as possible on the
same side of the PC board.
REFAN
Channel A Negative Reference I/O. Channel A conversion range is ±2/3 x (VREFAP - VREFAN). Bypass
REFAN with a 0.1µF capacitor to GND. Connect a 10µF and a 1µF bypass capacitor between REFAP
and REFAN. Place the 1µF REFAP-to-REFAN capacitor as close to the device as possible on the
same side of the PC board.
REFBN
Channel B Negative Reference I/O. Channel B conversion range is ±2/3 x (VREFBP - VREFBN). Bypass
REFBN with a 0.1µF capacitor to GND. Connect a 10µF and a 1µF bypass capacitor between REFBP
and REFBN. Place the 1µF REFBP-to-REFBN capacitor as close to the device as possible on the
same side of the PC board.
11
REFBP
Channel B Positive Reference I/O. Channel B conversion range is ±2/3 x (VREFBP - VREFBN). Bypass
REFBP with a 0.1µF capacitor to GND. Connect a 10µF and a 1µF bypass capacitor between REFBP
and REFBN. Place the 1µF REFBP-to-REFBN capacitor as close to the device as possible on the
same side of the PC board.
12
COMB
15
INBN
16
INBP
7
8
10
FUNCTION
Channel A Common-Mode Voltage I/O. Bypass COMB to GND with a 0.1µF capacitor.
Channel B Negative Analog Input
Channel B Positive Analog Input
18
DIFFCLK/
SECLK
19
CLKN
20
CLKP
21
DIV2
Differential/Single-Ended Input Clock Drive. This input selects between single-ended or differential clock
input drives.
DIFFCLK/SECLK = GND: Selects single-ended clock input drive.
DIFFCLK/SECLK = OVDD: Selects differential clock input drive.
Negative Clock Input. In differential clock input mode (DIFFCLK/SECLK = OVDD), connect a differential
clock signal between CLKP and CLKN. In single-ended clock mode (DIFFCLK/SECLK = GND), apply the
clock signal to CLKP and connect CLKN to GND.
Positive Clock Input. In differential clock input mode (DIFFCLK/SECLK = OVDD), connect a differential
clock signal between CLKP and CLKN. In single-ended clock mode (DIFFCLK/SECLK = GND), apply
the single-ended clock signal to CLKP and connect CLKN to GND.
Divide-by-Two Clock-Divider Digital Control Input. See Table 2 for details.
22
DIV4
Divide-by-Four Clock-Divider Digital Control Input. See Table 2 for details.
23–26, 61,
62, 63
VDD
Analog Power Input. Connect VDD to a 3.15V to 3.60V power supply. Bypass VDD to GND with a parallel
capacitor combination of ≥10µF and 0.1µF. Connect all VDD pins to the same potential.
27, 43, 60
OVDD
Output-Driver Power Input. Connect OVDD to a 1.7V to VDD power supply. Bypass OVDD to GND with a
parallel capacitor combination of ≥10µF and 0.1µF.
28, 29, 45,
46
N.C.
12
No Connection
______________________________________________________________________________________
Dual, 65Msps, 12-Bit, IF/Baseband ADC
PIN
NAME
FUNCTION
30
D0B
Channel B CMOS Digital Output, Bit 0 (LSB)
31
D1B
Channel B CMOS Digital Output, Bit 1
32
D2B
Channel B CMOS Digital Output, Bit 2
33
D3B
Channel B CMOS Digital Output, Bit 3
34
D4B
Channel B CMOS Digital Output, Bit 4
35
D5B
Channel B CMOS Digital Output, Bit 5
36
D6B
Channel B CMOS Digital Output, Bit 6
37
D7B
Channel B CMOS Digital Output, Bit 7
38
D8B
Channel B CMOS Digital Output, Bit 8
39
D9B
Channel B CMOS Digital Output, Bit 9
40
D10B
Channel B CMOS Digital Output, Bit 10
41
D11B
Channel B CMOS Digital Output, Bit 11 (MSB)
42
DORB
Channel B Data Out-of-Range Indicator. The DORB digital output indicates when the channel B analog
input voltage is out of range.
DORB = 1: Digital outputs exceed full-scale range.
DORB = 0: Digital outputs are within full-scale range.
44
DAV
47
D0A
Data-Valid Digital Output. The rising edge of DAV indicates that data is present on the digital outputs.
The MAX12527 evaluation kit (MAX12557 EV kit) utilizes DAV to latch data into any external back-end
digital logic.
Channel A CMOS Digital Output, Bit 0 (LSB)
48
D1A
Channel A CMOS Digital Output, Bit 1
49
D2A
Channel A CMOS Digital Output, Bit 2
50
D3A
Channel A CMOS Digital Output, Bit 3
51
D4A
Channel A CMOS Digital Output, Bit 4
52
D5A
Channel A CMOS Digital Output, Bit 5
53
D6A
Channel A CMOS Digital Output, Bit 6
54
D7A
Channel A CMOS Digital Output, Bit 7
55
D8A
Channel A CMOS Digital Output, Bit 8
56
D9A
Channel A CMOS Digital Output, Bit 9
57
D10A
Channel A CMOS Digital Output, Bit 10
58
D11A
59
DORA
64
G/T
Channel A CMOS Digital Output, Bit 11 (MSB)
Channel A Data Out-of-Range Indicator. The DORA digital output indicates when the channel A analog
input voltage is out of range.
DORA = 1: Digital outputs exceed full-scale range.
DORA = 0: Digital outputs are within full-scale range.
Output Format Select Digital Input.
G/T = GND: Two’s-complement output format selected.
G/T = OVDD: Gray-code output format selected.
65
PD
Power-Down Digital Input.
PD = GND: ADCs are fully operational.
PD = OVDD: ADCs are powered down.
______________________________________________________________________________________
13
MAX12527
Pin Description (continued)
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
Pin Description (continued)
PIN
NAME
66
SHREF
67
REFOUT
68
REFIN
—
EP
FUNCTION
Shared Reference Digital Input.
SHREF = VDD: Shared reference enabled.
SHREF = GND: Shared reference disabled.
When sharing the reference, externally connect REFAP and REFBP together to ensure that VREFAP
equals VREFBP. Similarly, when sharing the reference, externally connect REFAN to REFBN together to
ensure that VREFAN = VREFBN.
Internal Reference Voltage Output. The REFOUT output voltage is 2.048V and REFOUT can deliver 1mA.
For internal reference operation, connect REFOUT directly to REFIN or use a resistive divider from
REFOUT to set the voltage at REFIN. Bypass REFOUT to GND with a ≥0.1µF capacitor.
For external reference operation, REFOUT is not required and must be bypassed to GND with a ≥0.1µF
capacitor.
Single-Ended Reference Analog Input.
For internal reference and buffered external reference operation, apply a 0.7V to 2.3V DC reference
voltage to REFIN. Bypass REFIN to GND with a 4.7µF capacitor. Within its specified operating voltage,
REFIN has a >50MΩ input impedance, and the differential reference voltage (VREF_P - VREF_N) is
generated from REFIN. For unbuffered external reference operation, connect REFIN to GND. In this
mode REF_P, REF_N, and COM_ are high-impedance inputs that accept the external reference voltages.
Exposed Paddle. EP is internally connected to GND. Externally connect EP to GND to achieve specified
dynamic performance.
+
MAX12527
Σ
x2
−
FLASH
ADC
DAC
IN_P
STAGE 1
STAGE 2
STAGE 9
IN_N
STAGE 10
END OF PIPELINE
DIGITAL ERROR CORRECTION
D0_ THROUGH D11_
Figure 1. Pipeline Architecture—Stage Blocks
Detailed Description
The MAX12527 uses a 10-stage, fully differential,
pipelined architecture (Figure 1) that allows for highspeed conversion while minimizing power consumption. Samples taken at the inputs move progressively
through the pipeline stages every half clock cycle.
From input to output the total latency is 8 clock cycles.
14
Each pipeline converter stage converts its input voltage
to a digital output code. At every stage, except the last,
the error between the input voltage and the digital output code is multiplied and passed along to the next
pipeline stage. Digital error correction compensates for
ADC comparator offsets in each pipeline stage and
ensures no missing codes. Figure 2 shows the
MAX12527 functional diagram.
______________________________________________________________________________________
Dual, 65Msps, 12-Bit, IF/Baseband ADC
MAX12527
CLOCK
INAP
INAN
REFAP
COMA
REFAN
12-BIT
PIPELINE
ADC
CHANNEL A
REFERENCE
SYSTEM
DIGITAL
ERROR
CORRECTION
DATA
FORMAT
OUTPUT
DRIVERS
D0A TO D11A
DORA
MAX12527
G/T
REFIN
INTERNAL
REFERENCE
GENERATOR
REFOUT
DAV
SHREF
REFBP
COMB
REFBN
INBP
INBN
OVDD
CHANNEL B
REFERENCE
SYSTEM
12-BIT
PIPELINE
ADC
DIGITAL
ERROR
CORRECTION
DATA
FORMAT
OUTPUT
DRIVERS
D0B TO D11B
DORB
CLOCK
VDD
DIFFCLK/SECLK
CLOCK
CLKP
CLKN
DIV2
DIV4
CLOCK
DIVIDER
DUTY-CYCLE
EQUALIZER
POWER
CONTROL
AND
BIAS CIRCUITS
PD
GND
Figure 2. Functional Diagram
______________________________________________________________________________________
15
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
Table 1. Reference Modes
BOND WIRE
INDUCTANCE
1.5nH
VDD
VREFIN
MAX12527
IN_P
CPAR
2pF
BOND WIRE
INDUCTANCE
1.5nH
*CSAMPLE
4.5pF
VDD
Internal Reference Mode.
REFIN is driven by REFOUT either through a
35% VREFOUT
direct short or a resistive divider.
to 100%
VCOM_ = VDD / 2
VREFOUT
VREF_P = VDD / 2 + 3/8 x VREFIN
VREF_N = VDD / 2 - 3/8 x VREFIN
IN_N
CPAR
2pF
*CSAMPLE
4.5pF
0.7V to 2.3V
SAMPLING
CLOCK
*THE EFFECTIVE RESISTANCE OF THE
SWITCHED SAMPLING CAPACITORS IS: RIN =
1
fCLK x CSAMPLE
Figure 3. Internal T/H Circuit
Analog Inputs and Input Track-and-Hold
(T/H) Amplifier
Figure 3 displays a simplified functional diagram of the
input T/H circuit. This input T/H circuit allows for high
analog input frequencies of 175MHz and beyond and
supports a VDD / 2 common-mode input voltage.
The MAX12527 sampling clock controls the switchedcapacitor input T/H architecture (Figure 3) allowing the
analog input signals to be stored as charge on the
sampling capacitors. These switches are closed (track
mode) when the sampling clock is high and open (hold
mode) when the sampling clock is low (Figure 4). The
analog input signal source must be able to provide the
dynamic currents necessary to charge and discharge
the sampling capacitors. To avoid signal degradation,
these capacitors must be charged to one-half LSB
accuracy within one-half of a clock cycle. The analog
input of the MAX12527 supports differential or singleended input drive. For optimum performance with differential inputs, balance the input impedance of IN_P
and IN_N and set the common-mode voltage to midsupply (VDD / 2). The MAX12527 provides the optimum
common-mode voltage of VDD / 2 through the COM
output when operating in internal reference mode and
buffered external reference mode. This COM output
voltage can be used to bias the input network as shown
in Figures 9, 10, and 11.
Reference Output
An internal bandgap reference is the basis for all the
internal voltages and bias currents used in the
16
REFERENCE MODE
<0.5V
Buffered External Reference Mode.
An external 0.7V to 2.3V reference voltage is
applied to REFIN.
VCOM_ = VDD / 2
VREF_P = VDD / 2 + 3/8 x VREFIN
VREF_N = VDD / 2 - 3/8 x VREFIN
Unbuffered External Reference Mode.
REF_P, REF_N, and COM_ are driven by
external reference sources. The full-scale
analog input range is ±(VREF_P - VREF_N) x 2/3.
MAX12527. The power-down logic input (PD) enables
and disables the reference circuit. REFOUT has approximately 17kΩ to GND when the MAX12527 is powered
down. The reference circuit requires 10ms to power up
and settle to its final value when power is applied to the
MAX12527 or when PD transitions from high to low.
The internal bandgap reference produces a buffered
reference voltage of 2.048V ±1% at the REFOUT pin
with a ±50ppm/°C temperature coefficient. Connect an
external ≥0.1µF bypass capacitor from REFOUT to
GND for stability. REFOUT sources up to 1mA and
sinks up to 0.1mA for external circuits with a 35mV/mA
load regulation. Short-circuit protection limits IREFOUT
to a 2.1mA source current when shorted to GND and a
0.24mA sink current when shorted to VDD. Similar to
REFOUT, REFIN should be bypassed with a 4.7µF
capacitor to GND.
Reference Configurations
The MAX12527 full-scale analog input range is ±2/3 x
VREF with a VDD / 2 ±0.5V common-mode input range.
VREF is the voltage difference between REFAP (REFBP)
and REFAN (REFBN). The MAX12527 provides three
modes of reference operation. The voltage at REFIN
(VREFIN) selects the reference operation mode (Table 1).
Connect REFOUT to REFIN either with a direct short or
through a resistive divider to enter internal reference
mode. COM_, REF_P, and REF_N are low-impedance
outputs with VCOM_ = VDD / 2, VREFP = VDD / 2 + 3/8 x
VREFIN, and VREF_N = VDD / 2 - 3/8 x VREFIN. Bypass
REF_P, REF_N, and COM_ each with a 0.1µF capacitor
to GND. Bypass REF_P to REF_N with a 10µF capacitor.
______________________________________________________________________________________
Dual, 65Msps, 12-Bit, IF/Baseband ADC
For detailed circuit suggestions and how to drive the
ADC in buffered/unbuffered external reference mode,
see the Applications Information section.
Clock Duty-Cycle Equalizer
The MAX12527 has an internal clock duty-cycle equalizer, which makes the converter insensitive to the duty
cycle of the signal applied to CLKP and CLKN. The converters allow clock duty-cycle variations from 25% to 75%
without negatively impacting the dynamic performance.
The clock duty-cycle equalizer uses a delay-locked
loop (DLL) to create internal timing signals that are
duty-cycle independent. Due to this DLL, the
MAX12527 requires approximately 100 clock cycles to
acquire and lock to new clock frequencies.
Clock Input and Clock Control Lines
The MAX12527 accepts both differential and singleended clock inputs with a wide 25% to 75% input clock
duty cycle. For single-ended clock input operation,
connect DIFFCLK/SECLK and CLKN to GND. Apply an
external single-ended clock signal to CLKP. To reduce
clock jitter, the external single-ended clock must have
sharp falling edges. For differential clock input operation, connect DIFFCLK/SECLK to OV DD . Apply an
external differential clock signal to CLKP and CLKN.
Consider the clock input as an analog input and route it
away from any other analog inputs and digital signal
lines. CLKP and CLKN enter high impedance when the
MAX12527 is powered down (Figure 4).
Low clock jitter is required for the specified SNR performance of the MAX12527. The analog inputs are sampled on the falling (rising) edge of CLKP (CLKN),
requiring this edge to have the lowest possible jitter.
Jitter limits the maximum SNR performance of any ADC
according to the following relationship:


1
SNR = 20 × log 

2
×
π
×
f
×
t

IN
J
where fIN represents the analog input frequency and tJ
is the total system clock jitter. Clock jitter is especially
critical for undersampling applications. For instance,
assuming that clock jitter is the only noise source, to
obtain the specified 69.8dB of SNR with an input frequency of 175MHz the system must have less than
0.29ps of clock jitter. However, in reality there are other
noise sources such as thermal noise and quantization
noise that contribute to the system noise requiring the
clock jitter to be less than 0.14ps to obtain the specified 69.8dB of SNR at 175MHz.
Clock-Divider Control Inputs (DIV2, DIV4)
The MAX12527 features three different modes of sampling/clock operation (see Table 2). Pulling both control
lines low, the clock-divider function is disabled and the
converters sample at full clock speed. Pulling DIV4 low
and DIV2 high enables the divide-by-two feature, which
sets the sampling speed to one-half the selected clock
frequency. In divide-by-four mode, the converter sampling speed is set to one-fourth the clock speed of the
MAX12527. Divide-by-four mode is achieved by applying
a high level to DIV4 and a low level to DIV2. The option to
select either one-half or one-fourth of the clock speed for
______________________________________________________________________________________
17
MAX12527
Bypass REFIN and REFOUT to GND with a 0.1µF capacitor. The REFIN input impedance is very large (>50MΩ).
When driving REFIN through a resistive divider, use
resistances ≥10kΩ to avoid loading REFOUT.
Buffered external reference mode is virtually identical to
the internal reference mode except that the reference
source is derived from an external reference and not the
MAX12527’s internal bandgap reference. In buffered
external reference mode, apply a stable reference voltage source between 0.7V to 2.3V at REFIN. Pins COM_,
REF_P, and REF_N are low-impedance outputs with
VCOM_ = VDD / 2, VREF_P = VDD / 2 + 3/8 x VREFIN, and
VREF_N = VDD / 2 - 3/8 x VREFIN. Bypass REF_P, REF_N,
and COM_ each with a 0.1µF capacitor to GND. Bypass
REF_P to REF_N with a 10µF capacitor.
Connect REFIN to GND to enter unbuffered external reference mode. Connecting REFIN to GND deactivates
the on-chip reference buffers for COM_, REF_P, and
REF_N. With their buffers deactivated, COM_, REF_P,
and REF_N become high-impedance inputs and must
be driven with separate, external reference sources.
Drive VCOM_ to VDD / 2 ±5%, and drive REF_P and
REF_N so VCOM_ = (VREF_P_ + VREF_N_) / 2. The analog
input range is ±(V REF_P_ - V REF_N ) x 2/3. Bypass
REF_P, REF_N, and COM_ each with a 0.1µF capacitor
to GND. Bypass REF_P to REF_N with a 10µF capacitor.
For all reference modes, bypass REFOUT with a 0.1µF
and REFIN with a 4.7µF capacitor to GND.
The MAX12527 also features a shared reference mode,
in which the user can achieve better channel-to-channel matching. When sharing the reference (SHREF =
VDD), externally connect REFAP and REFBP together to
ensure that VREFAP = VREFBP. Similarly, when sharing
the reference, externally connect REFAN to REFBN
together to ensure that VREFAN = VREFBN.
Connect SHREF to GND to disable the shared reference mode of the MAX12527. In this independent reference mode, a better channel-to-channel isolation is
achieved.
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
Table 2. Clock-Divider Control Inputs
VDD
S1H
MAX12527
DIV4
DIV2
0
0
Clock Divider Disabled
fSAMPLE = fCLK
0
1
Divide-by-Two Clock Divider
fSAMPLE = fCLK / 2
1
0
Divide-by-Four Clock Divider
fSAMPLE = fCLK / 4
1
1
Not Allowed
10kΩ
CLKP
10kΩ
DUTY-CYCLE
EQUALIZER
S2H
S1L
10kΩ
cuitry can be latched with the rising edge of the conversion clock (CLKP - CLKN).
CLKN
Data-Valid Output
DAV is a single-ended version of the input clock that is
compensated to correct for any input clock duty-cycle
variations. The MAX12527 output data changes on the
falling edge of DAV, and DAV rises once the output
data is valid. The falling edge of DAV is synchronized
to have a 5.4ns delay from the falling edge of the input
clock. Output data at D0A/B–D11A/B and DORA/B are
valid from 7ns before the rising edge of DAV to 7ns
after the rising edge of DAV.
DAV enters high impedance when the MAX12527 is
powered down (PD = OV DD ). DAV enters its highimpedance state 10ns after the rising edge of PD and
becomes active again 10ns after PD transitions low.
DAV is capable of sinking and sourcing 600µA and has
three times the driving capabilities of D0A/B–D11A/B
and DORA/B. DAV is typically used to latch the
MAX12527 output data into an external digital back-end
circuit. Keep the capacitive load on DAV as low as possible (<15pF) to avoid large digital currents feeding back
into the analog portion of the MAX12527, thereby
degrading its dynamic performance. Buffering DAV
10kΩ
S2L
GND
SWITCHES S1_ AND S2_ ARE OPEN
DURING POWER-DOWN MAKING
CLKP AND CLKN HIGH IMPEDANCE.
SWITCHES S2_ ARE OPEN IN
SINGLE-ENDED CLOCK MODE.
Figure 4. Siimplified Clock Input Circuit
sampling provides design flexibility, relaxes clock
requirements, and can minimize clock jitter.
System Timing Requirements
Figure 5 shows the timing relationship between the
clock, analog inputs, DAV indicator, DOR_ indicators,
and the resulting output data. The analog input is sampled on the falling (rising) edge of CLKP (CLKN) and
the resulting data appears at the digital outputs 8 clock
cycles later.
The DAV indicator is synchronized with the digital output and optimized for use in latching data into digital
back-end circuitry. Alternatively, digital back-end cirN+4
DIFFERENTIAL ANALOG INPUT (IN_P–IN_N)
(VREF_P - VREF_N) x 2/3
N+5
N+3
N-3
N-2
N-1
N
N+1
FUNCTION
N+6
N +2
N+7
N+9
N+8
(VREF_N - VREF_P) x 2/3
tAD
CLKN
CLKP
tDAV
tCL
tCH
DAV
tSETUP
D0_–D11_
tHOLD
N-3
8.0 CLOCK-CYCLE DATA LATENCY
N-2
N-1
N
N+1
N+2
N+3
N+4
N+5
N+6
N+7
tSETUP
DOR
Figure 5. System Timing Diagram
18
______________________________________________________________________________________
N+8
N+9
tHOLD
Dual, 65Msps, 12-Bit, IF/Baseband ADC
Data Out-of-Range Indicator
The DORA and DORB digital outputs indicate when the
analog input voltage is out of range. When DOR_ is high,
the analog input is out of range. When DOR_ is low, the
analog input is within range. The valid differential input
range is from (V REF_P - V REF_N ) x 2/3 to (V REF_N VREF_P) x 2/3. Signals outside of this valid differential
range cause DOR_ to assert high as shown in Table 1.
DOR is synchronized with DAV and transitions along
with the output data D11–D0. There is an 8 clock-cycle
latency in the DOR function as is with the output data
(Figure 5). DOR_ is high impedance when the
MAX12527 is in power-down (PD = high). DOR_ enters
a high-impedance state within 10ns after the rising edge
of PD and becomes active 10ns after PD’s falling edge.
Digital Output Data and Output Format Selection
The MAX12527 provides two 12-bit, parallel, tri-state
output buses. D0A/B–D11A/B and DORA/B update on
the falling edge of DAV and are valid on the rising edge
of DAV.
The MAX12527 output data format is either Gray code
or two’s complement depending on the logic input G/T.
With G/T high, the output data format is Gray code.
With G/T low, the output data format is set to two’s complement. See Figure 8 for a binary-to-Gray and Gray-tobinary code conversion example.
The following equations, Table 3, Figure 6, and Figure 7
define the relationship between the digital output and
the analog input.
Gray Code (G/T = 1):
VIN_P - VIN_N = 2/3 x (VREF_P - VREF_N) x 2 x
(CODE10 - 2048) / 4096
Two’s Complement (G/T = 0):
VIN_P - VIN_N = 2/3 x (VREF_P - VREF_N) x 2 x
CODE10 / 4096
where CODE10 is the decimal equivalent of the digital
output code as shown in Table 3.
Table 3. Output Codes vs. Input Voltage
GRAY-CODE OUTPUT CODE
(G/T = 1)
BINARY
D11A–D0A
D11B–D0B
TWO’S COMPLEMENT OUTPUT CODE
(G/T = 0)
DECIMAL
HEXADECIMAL
EQUIVALENT
EQUIVALENT
OF
OF
DOR
D11A–D0A
D11A–D0A
D11B–D0B
D11B–D0B
(CODE10)
BINARY
D11A–D0A
D11B–D0B
DECIMAL
VIN_P - VIN_N
HEXADECIMAL
EQUIVALENT VREF_P = 2.418V
EQUIVALENT
OF
VREF_N = 0.882V
OF
DOR
D11A–D0A
D11A–D0A
D11B–D0B
D11B–D0B
(CODE10)
0x7FF
+2047
>+1.0235V
(DATA OUT OF
RANGE)
0
0x7FF
+2047
+1.0235V
0
0x7FE
+2046
+1.0230V
0000 0000 0010
0
0x002
+2
+0.0010V
+2049
0000 0000 0001
0
0x001
+1
+0.0005V
+2048
0000 0000 0000
0
0x000
0
+0.0000V
0x400
+2047
1111 1111 1111
0
0xFFF
-1
-0.0005V
0
0x401
+2046
1111 1111 1110
0
0xFFE
-2
-0.0010V
0000 0000 0001
0
0x001
+1
1000 0000 0001
0
0x801
-2047
-1.0235V
0000 0000 0000
0
0x000
0
1000 0000 0000
0
0x800
-2048
-1.0240V
-2048
<-1.0240V
(DATA OUT OF
RANGE)
1000 0000 0000
1
0x800
+4095
0111 1111 1111
1
1000 0000 0000
0
0x800
+4095
0111 1111 1111
1000 0000 0001
0
0x801
+4094
0111 1111 1110
1100 0000 0011
0
0xC03
+2050
1100 0000 0001
0
0xC01
1100 0000 0000
0
0xC00
0100 0000 0000
0
0100 0000 0001
0000 0000 0000
1
0x000
0
1000 0000 0000
1
0x800
______________________________________________________________________________________
19
MAX12527
externally isolates it from heavy capacitive loads. Refer
to the MAX12527 EV Kit schematic for recommendations
of how to drive the DAV signal through an external buffer.
1 LSB = 4/3 x (VREFP - VREFN) / 4096
2/3 x (VREFP - VREFN)
1 LSB = 4/3 x (VREFP - VREFN) / 4096
2/3 x (VREFP - VREFN)
2/3 x (VREFP - VREFN)
0x7FF
0x7FE
0x800
0x801
0x7FD
0x803
GRAY OUTPUT CODE (LSB)
TWO'S-COMPLEMENT OUTPUT CODE (LSB)
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
0x001
0x000
0xFFF
0xC01
0xC00
0xC00
0x803
0x802
0x002
0x003
0x801
0x800
0x001
0x000
-2047 -2045
-1 0 +1
+2045 +2047
DIFFERENTIAL INPUT VOLTAGE (LSB)
2/3 x (VREFP - VREFN)
-2047 -2045
-1 0 +1
+2045 +2047
DIFFERENTIAL INPUT VOLTAGE (LSB)
Figure 6. Two’s-Complement Transfer Function (G/T = 0)
Figure 7. Gray-Code Transfer Function (G/T = 1)
The digital outputs D0A/B–D11A/B are high impedance
when the MAX12527 is in power-down (PD = 1) mode.
D0A/B–D11A/B enter this state 10ns after the rising
edge of PD and become active again 10ns after PD
transitions low.
In power-down mode all internal circuits are off, the
analog supply current reduces to less than 50µA, and
the digital supply current reduces to 1µA. The following
list shows the state of the analog inputs and digital outputs in power-down mode.
1) INAP/B, INAN/B analog inputs are disconnected
from the internal input amplifier (Figure 3).
Keep the capacitive load on the MAX12527 digital outputs D0A/B–D11A/B as low as possible (<15pF) to
avoid large digital currents feeding back into the analog portion of the MAX12527 and degrading its dynamic performance. Adding external digital buffers on the
digital outputs helps isolate the MAX12527 from heavy
capacitive loads. To improve the dynamic performance
of the MAX12527, add 220Ω resistors in series with the
digital outputs close to the MAX12527. See the
MAX12557 EV kit schematic for guidelines of how to
drive the digital outputs through 220Ω series resistors
and external digital output buffers.
Power-Down Input
The MAX12527 has two power modes that are controlled with a power-down digital input (PD). With PD
low, the MAX12527 is in its normal operating mode.
With PD high, the MAX12527 is in power-down mode.
The power-down mode allows the MAX12527 to efficiently use power by transitioning to a low-power state
when conversions are not required. Additionally, the
MAX12527 parallel output bus goes high-impedance in
power-down mode, allowing other devices on the bus
to be accessed.
20
2) REFOUT has approximately 17kΩ to GND.
3) REFAP/B, COMA/B, REFAN/B enter a high-impedance state with respect to VDD and GND, but there
is an internal 4kΩ resistor between REFAP/B and
COMA/B as well as an internal 4kΩ resistor
between REFAN/B and COMA/B.
4) D0A–D11A, D0B–D11B, DORA, and DORB enter a
high-impedance state.
5) DAV enters a high-impedance state.
6) CLKP, CLKN clock inputs enter a high-impedance
state (Figure 4).
The wake-up time from power-down mode is dominated
by the time required to charge the capacitors at REF_P,
REF_N, and COM. In internal reference mode and
buffered external reference mode the wake-up time is
typically 10ms. When operating in the unbuffered external reference mode the wake-up time is dependent on
the external reference drivers.
______________________________________________________________________________________
Dual, 65Msps, 12-Bit, IF/Baseband ADC
GRAY-TO-BINARY CODE CONVERSION
1) THE MOST SIGNIFICANT BINARY BIT IS THE SAME AS THE
MOST SIGNIFICANT GRAY-CODE BIT.
D11
0
D7
1
1
1
0
D3
1
0
0
1
D0
1
0
0
0
BIT POSITION
D11
BINARY
0
GRAY CODE
0
2) SUBSEQUENT GRAY-CODE BITS ARE FOUND ACCORDING
TO THE FOLLOWING EQUATION:
1
0
0
1
D3
1
1
GRAYX = BINARYX + BINARYX + 1
BINARY10 = 0 + 1
GRAY10 = 1
BINARY10 = 1
D7
1
1
0
D3
1
0
1
0
GRAY CODE
BINARYX = BINARYX+1 + GRAYX
BINARY10 = BINARY11 + GRAY10
1
0
WHERE + IS THE EXCLUSIVE OR FUNCTION (SEE TRUTH
TABLE BELOW) AND X IS THE BIT POSITION:
GRAY10 = 1 + 0
+
1
BIT POSITION
BINARY
GRAY10 = BINARY10 + BINARY11
D11
0
D0
2) SUBSEQUENT BINARY BITS ARE FOUND ACCORDING TO
THE FOLLOWING EQUATION:
WHERE + IS THE EXCLUSIVE OR FUNCTION (SEE TRUTH
TABLE BELOW) AND X IS THE BIT POSITION:
0
D7
MAX12527
BINARY-TO-GRAY CODE CONVERSION
1) THE MOST SIGNIFICANT GRAY-CODE BIT IS THE SAME
AS THE MOST SIGNIFICANT BINARY BIT.
0
1
D0
1
0
0
D11
BIT POSITION
BINARY
0
GRAY CODE
0
D7
1
0
0
1
D3
1
1
0
1
D0
0
1
0
BIT POSITION
GRAY CODE
+
0
1
3) REPEAT STEP 2 UNTIL COMPLETE:
BINARY
1
3) REPEAT STEP 2 UNTIL COMPLETE:
GRAY9 = BINARY9 + BINARY10
BINARY9 = BINARY10 + GRAY9
GRAY9 = 1 + 1
BINARY9 = 1 + 0
GRAY9 = 0
BINARY9 = 1
D11
0
1
0
1
D7
+
1
1
0
D3
1
0
0
1
D0
1
0
0
BIT POSITION
D11
BINARY
0
1
GRAY CODE
0
1
D7
0
0
1
D3
1
1
0
1
D0
0
1
0
BIT POSITION
GRAY CODE
+
0
4) THE FINAL GRAY-CODE CONVERSION IS:
D11
D7
1
BINARY
4) THE FINAL BINARY CONVERSION IS:
D3
D0
BIT POSITION
D11
D7
D3
D0
BIT POSITION
0
1
1
1
0
1
0
0
1
1
0
0
BINARY
0
1
0
0
1
1
1
0
1
0
1
0
GRAY CODE
0
1
0
0
1
1
1
0
1
0
1
0
GRAY CODE
0
1
1
1
0
1
0
0
1
1
0
0
BINARY
EXCLUSIVE OR TRUTH TABLE
FIGURE 8 SHOWS THE GRAY-TO-BINARY AND BINARY-TO-GRAY
CODE CONVERSION IN OFFSET BINARY FORMAT. THE OUTPUT
FORMAT OF THE MAX12527 IS TWO'S-COMPLEMENT BINARY,
HENCE EACH MSB OF THE TWO'S-COMPLEMENT OUTPUT CODE
MUST BE INSERTED TO REFLECT TRUE OFFSET BINARY FORMAT.
A
B
0
0
1
1
0
1
0
1
Y
=
A
+
B
0
1
1
0
Figure 8. Binary-to-Gray and Gray-to-Binary Code Conversion
______________________________________________________________________________________
21
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
overall distortion. The configuration of Figure 9 is good
for frequencies up to Nyquist (fCLK / 2).
The circuit of Figure 10 converts a single-ended input
signal to fully differential just as Figure 9. However,
Figure 10 utilizes an additional transformer to improve
the common-mode rejection allowing high-frequency
signals beyond the Nyquist frequency. A set of 75Ω
and 113Ω termination resistors provide an equivalent
50Ω termination to the signal source. The second set of
termination resistors connects to COM_ providing the
correct input common-mode voltage. Two 0Ω resistors
in series with the analog inputs allow high IF input frequencies. These 0Ω resistors can be replaced with lowvalue resistors to limit the input bandwidth.
Applications Information
Using Transformer Coupling
In general, the MAX12527 provides better SFDR and
THD with fully differential input signals than singleended input drive, especially for input frequencies
above 125MHz. In differential input mode, even-order
harmonics are lower as both inputs are balanced, and
each of the ADC inputs only requires half the signal
swing compared to single-ended input mode.
An RF transformer (Figure 9) provides an excellent
solution to convert a single-ended input source signal
to a fully differential signal, required by the MAX12527
for optimum performance. Connecting the center tap of
the transformer to COM provides a VDD / 2 DC level
shift to the input. Although a 1:1 transformer is shown, a
step-up transformer can be selected to reduce the
drive requirements. A reduced signal swing from the
input driver, such as an op amp, can also improve the
Single-Ended AC-Coupled Input Signal
Figure 11 shows an AC-coupled, single-ended input
application. The MAX4108 provides high speed, high
bandwidth, low noise, and low distortion to maintain the
input signal integrity.
24.9Ω
IN_P
5.6pF
0.1µF
VIN
1
6
N.C.
5
VIN
MAX12527
T1
0.1µF
0Ω
IN_P
MAX4108
5.6pF
2
COM_
100Ω
24.9Ω
MAX12527
0.1µF
3
4
MINICIRCUITS
TT1-6
OR
T1-1T
COM_
0.1µF
100Ω
24.9Ω
24.9Ω
IN_N
IN_N
5.6pF
5.6pF
Figure 11. Single-Ended, AC-Coupled Input Drive
Figure 9. Transformer-Coupled Input Drive for Input Frequencies
Up to Nyquist
0Ω*
IN_P
0.1µF
1
VIN
N.C.
5
T1
6
2
1
75Ω
1%
N.C.
N.C.
5
T2
5.6pF
6
2
113Ω
0.5%
MAX12527
COM_
N.C.
0.1µF
3
4
MINICIRCUITS
ADT1-1WT
75Ω
1%
3
4
MINICIRCUITS
ADT1-1WT
113Ω
0.5%
0Ω*
IN_N
5.6pF
*0Ω RESISTORS CAN BE REPLACED WITH
LOW-VALUE RESISTORS TO LIMIT THE INPUT BANDWIDTH.
Figure 10. Transformer-Coupled Input Drive for Input Frequencies beyond Nyquist
22
______________________________________________________________________________________
Dual, 65Msps, 12-Bit, IF/Baseband ADC
0.1µF
2.2µF
VDD
REF_P
REFIN
0.1µF
0.1µF
1
5
16.2kΩ
3
MAX6029
(EUK21)
0.1µF
1
47Ω
300µF
6V
0.1µF
REF_N
MAX4230
4
10µF
MAX12527
5
1µF
2.048V
0.1µF
2
2
COM_
REFOUT
1.47kΩ
GND
0.1µF
0.1µF
NOTE: ONE FRONT-END REFERENCE CIRCUIT IS
CAPABLE OF SOURCING UP TO 15mA AND
SINKING UP TO 30mA OF OUTPUT CURRENT.
3.3V
0.1µF
2.2µF
VDD
REF_P
REFIN
0.1µF
10µF
MAX12527
0.1µF
REF_N
0.1µF
COM_
REFOUT
0.1µF
GND
0.1µF
Figure 12. External Buffered (MAX4230) Reference Drive Using a MAX6029 Bandgap Reference
Buffered External Reference Drives
Multiple ADCs
The buffered external reference mode allows for more
control over the MAX12527 reference voltage and
allows multiple converters to use a common reference.
The REFIN input impedance is >50MΩ.
Figure 12 shows the MAX6029 precision 2.048V bandgap
reference used as a common reference for multiple converters. The 2.048V output of the MAX6029 passes
through a single-pole 10Hz LP filter to the MAX4230.
The MAX4230 buffers the 2.048V reference and provides additional 10Hz LP filtering before its output is
applied to the REFIN input of the MAX12527.
Unbuffered External Reference Drives
Multiple ADCs
The unbuffered external reference mode allows for precise control over the MAX12527 reference and allows
multiple converters to use a common reference.
Connecting REFIN to GND disables the internal refer-
______________________________________________________________________________________
23
MAX12527
3.3V
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
3.3V
3V
0.1µF
0.1µF
1
2.2µF
5
MAX6029
(EUK30)
20kΩ
1%
REF_P
REFOUT
0.1µF
20kΩ
1%
2
VDD
10µF
MAX12527
2.413V
1
4
REF_N
47Ω
0.1µF
MAX4230
3
0.47µF
330µF
6V
10µF
6V
1.47kΩ
52.3kΩ
1%
COM_
0.1µF
4
47Ω
MAX4230
3
3.3V
330µF
6V
10µF
6V
52.3kΩ
1%
1.47kΩ
0.1µF
4
47Ω
REF_P
MAX4230
3
2.2µF
0.880V
1
20kΩ
1%
REFIN
GND
1.647V
1
20kΩ
1%
0.1µF
0.1µF
VDD
REFOUT
0.1µF
10µF
6V
330µF
6V
10µF
0.1µF
0.1µF
MAX12527
1.47kΩ
REF_N
0.1µF
20kΩ
1%
COM_
0.1µF
GND
REFIN
Figure 13. External Unbuffered Reference Driving Multiple ADCs
ence, allowing REF_P, REF_N, and COM_ to be driven
directly by a set of external reference sources.
Figure 13 uses a MAX6029 precision 3.000V bandgap
reference as a common reference for multiple converters. A seven-component resistive divider chain follows
the MAX6029 voltage reference. The 0.47µF capacitor
along this chain creates a 10Hz LP filter. Three
MAX4230 amplifiers buffer taps along this resistor
chain providing 2.413V, 1.647V, and 0.880V to the
MAX12527 REF_P, REF_N, and COM_ reference
inputs. The feedback around the MAX4230 op amps
provides additional 10Hz LP filtering. Reference voltages 2.413V and 0.880V set the full-scale analog input
24
range for the converter to ±1.022V (±[VREF_P - VREF_N]
x 2/3).
Note that one single power supply for all active circuit
components removes any concern regarding powersupply sequencing when powering up or down.
Grounding, Bypassing, and
Board Layout
The MAX12527 requires high-speed board layout
design techniques. Refer to the MAX12557 EV kit data
sheet for a board layout reference. Locate all bypass
capacitors as close to the device as possible, preferably on the same side as the ADC, using surface-
______________________________________________________________________________________
Dual, 65Msps, 12-Bit, IF/Baseband ADC
Route high-speed digital signal traces away from the
sensitive analog traces. Keep all signal lines short and
free of 90° turns.
Ensure that the differential, analog input network layout
is symmetric and that all parasitic components are balanced equally. Refer to the MAX12557 EV kit data
sheet for an example of symmetric input layout.
Parameter Definitions
Integral Nonlinearity (INL)
INL is the deviation of the values on an actual transfer
function from a straight line. For the MAX12527, this
straight line is between the endpoints of the transfer
function, once offset and gain errors have been nullified. INL deviations are measured at every step of the
transfer function and the worst-case deviation is reported in the Electrical Characteristics table.
Differential Nonlinearity (DNL)
DNL is the difference between an actual step width and
the ideal value of 1 LSB. A DNL error specification of
less than 1 LSB guarantees no missing codes and a
monotonic transfer function. For the MAX12527, DNL
deviations are measured at every step of the transfer
function and the worst-case deviation is reported in the
Electrical Characteristics table.
Offset Error
Offset error is a figure of merit that indicates how well
the actual transfer function matches the ideal transfer
function at a single point. Ideally, the midscale
MAX12527 transition occurs at 0.5 LSB above midscale. The offset error is the amount of deviation
between the measured midscale transition point and
the ideal midscale transition point.
Gain Error
Gain error is a figure of merit that indicates how well the
slope of the actual transfer function matches the slope of
the ideal transfer function. The slope of the actual transfer function is measured between two data points: positive full scale and negative full scale. Ideally, the positive
full-scale MAX12527 transition occurs at 1.5 LSBs below
positive full scale, and the negative full-scale transition
occurs at 0.5 LSB above negative full scale. The gain
error is the difference of the measured transition points
minus the difference of the ideal transition points.
Small-Signal Noise Floor (SSNF)
SSNF is the integrated noise and distortion power in the
Nyquist band for small-signal inputs. The DC offset is
excluded from this noise calculation. For this converter,
a small signal is defined as a single tone with an amplitude of -35dBFS. This parameter captures the thermal
and quantization noise characteristics of the data converter and can be used to help calculate the overall
noise figure of a digital receiver signal path.
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
minimum analog-to-digital noise is caused by quantization error only and results directly from the ADC’s resolution (N bits):
SNR[max] = 6.02 × N + 1.76
In reality, there are other noise sources besides quantization noise: thermal noise, reference noise, clock jitter,
etc. SNR is computed by taking the ratio of the RMS
signal to the RMS noise. RMS noise includes all spectral components to the Nyquist frequency excluding the
fundamental, the first six harmonics (HD2 through
HD7), and the DC offset.
SNR = 20 x log (SIGNALRMS / NOISERMS)
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS signal to the RMS noise plus distortion. RMS noise plus
distortion includes all spectral components to the
Nyquist frequency excluding the fundamental and the
DC offset.
______________________________________________________________________________________
25
MAX12527
mount devices for minimum inductance. Bypass VDD to
GND with a 220µF ceramic capacitor in parallel with at
least one 10µF, one 4.7µF, and one 0.1µF ceramic
capacitor. Bypass OVDD to GND with a 220µF ceramic
capacitor in parallel with at least one 10µF, one 4.7µF,
and one 0.1µF ceramic capacitor. High-frequency
bypassing/decoupling capacitors should be located as
close as possible to the converter supply pins.
Multilayer boards with ample ground and power planes
produce the highest level of signal integrity. All grounds
and the exposed backside paddle of the MAX12527
must be connected to the same ground plane. The
MAX12527 relies on the exposed backside paddle connection for a low-inductance ground connection. Isolate
the ground plane from any noisy digital system ground
planes such as a DSP or output buffer ground.
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
Total Harmonic Distortion (THD)
THD is the ratio of the RMS sum of the first six harmonics of the input signal to the fundamental itself. This is
expressed as:

V22 + V32 + V4 2 + V52 + V62 + V72
THD = 20 × log 

V1





where V1 is the fundamental amplitude, and V2 through
V7 are the amplitudes of the 2nd- through 7th-order
harmonics (HD2 through HD7).
Spurious-Free Dynamic Range (SFDR)
SFDR is the ratio expressed in decibels of the RMS
amplitude of the fundamental (maximum signal component) to the RMS value of the next largest spurious
component, excluding DC offset.
Intermodulation Distortion (IMD)
IMD is the total power of the IM2 to IM5 intermodulation
products to the Nyquist frequency relative to the total
input power of the two input tones fIN1 and fIN2. The
individual input tone levels are at -7dBFS. The intermodulation products are as follows:
2nd-Order Intermodulation products (IM2):
fIN1 = fIN2, fIN2 - fIN1
3rd-Order Intermodulation products (IM3):
2 x fIN1 - fIN2, 2 x fIN2 - fIN1, 2 x fIN1 + fIN2,
2 x fIN2 + fIN1
4th-Order Intermodulation products (IM4):
3 x fIN1 - fIN2, 3 x fIN2 - fIN1, 3 x fIN1 + fIN2,
3 x fIN2 + fIN1, 2 x fIN1 - 2 x fIN2, 2 x fIN1 + 2 x fIN2,
2 x fIN2 - 2 x fIN1
5th-Order Intermodulation products (IM5):
3 x fIN1 - 2 x fIN2, 3 x fIN2 - 2 x fIN1, 3 x fIN1 + 2 x fIN2,
3 x fIN2 + 2 x fIN1, 4 x fIN1 - fIN2, 4 x fIN2 - fIN1,
4 x fIN1 + fIN2, 4 x fIN2 + fIN1
Note that the two-tone intermodulation distortion is measured with respect to a single-carrier amplitude and not
the peak-to-average input power of both input tones.
3rd-Order Intermodulation (IM3)
IM3 is the total power of the 3rd-order intermodulation
product to the Nyquist frequency relative to the total
input power of the two input tones fIN1 and fIN2. The
individual input tone levels are at -7dBFS. The 3rdorder intermodulation products are 2 x fIN1 - fIN2, 2 x
fIN2 - fIN1, 2 x fIN1 + fIN2, 2 x fIN2 + fIN1.
Aperture Jitter
Figure 14 shows the aperture jitter (tAJ), which is the
sample-to-sample variation in the aperture delay.
26
CLKN
CLKP
tAD
ANALOG
INPUT
tAJ
SAMPLED
DATA
T/H
HOLD
TRACK
HOLD
Figure 14. T/H Aperture Timing
Aperture Delay
Aperture delay (tAD) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken (Figure 14).
Full-Power Bandwidth
A large -0.2dBFS analog input signal is applied to an
ADC and the input frequency is swept up to the point
where the amplitude of the digitized conversion result
has decreased by -3dB. This point is defined as fullpower input bandwidth frequency.
Output Noise (nOUT)
The output noise (nOUT) parameter is similar to thermal
plus quantization noise and is an indication of the converter’s overall noise performance.
No fundamental input tone is used to test for nOUT.
IN_P, IN_N, and COM_ are connected together and
1024k data points are collected. nOUT is computed by
taking the RMS value of the collected data points after
the mean is removed.
Overdrive Recovery Time
Overdrive recovery time is the time required for the
ADC to recover from an input transient that exceeds the
full-scale limits. The MAX12527 specifies overdrive
recovery time using an input transient that exceeds the
full-scale limits by ±10%. The MAX12527 requires one
clock cycle to recover from the overdrive condition.
Crosstalk
Coupling onto one channel being driven by a
(-0.5dBFS) signal when the adjacent interfering channel
is driven by a full-scale signal. Measurement includes
all spurs resulting from both direct coupling and mixing
components.
______________________________________________________________________________________
Dual, 65Msps, 12-Bit, IF/Baseband ADC
63 62 61 60 59 58
D6A
D5A
D7A
D8A
D9A
D10A
D11A
DORA
OVDD
VDD
VDD
VDD
G/T
67 66 65 64
PD
68
SHREF
REFOUT
TOP VIEW
REFIN
Pin Configuration
57 56 55 54 53 52
Offset Matching
GND
1
51 D4A
Like gain matching, offset matching is a figure of merit
that indicates how well the offsets between the two channels are matched to each other. The same input signal is
applied to both channels and the maximum deviation in
offset is reported (typically in %FSR) as offset matching.
INAP
2
50 D3A
INAN
3
49 D2A
GND
4
48 D1A
GND
5
47 D0A
COMA
6
46 N.C.
REFAP
7
45 N.C.
REFAN
8
GND
9
44 DAV
43 OVDD
MAX12527
REFBN 10
42 DORB
REFBP 11
41 D11B
COMB 12
40 D10B
GND 13
39 D9B
GND 14
38 D8B
INBN 15
37 D7B
EXPOSED PADDLE (GND)
INBP 16
36 D6B
GND 17
35 D5B
D4B
D3B
D2B
D1B
D0B
N.C.
N.C.
OVDD
VDD
VDD
VDD
VDD
DIV4
DIV2
CLKP
CLKN
DIFFCLK/SECLK
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
THIN QFN
______________________________________________________________________________________
27
MAX12527
Gain Matching
Gain matching is a figure of merit that indicates how
well the gains between the two channels are matched
to each other. The same input signal is applied to both
channels and the maximum deviation in gain is reported (typically in dB) as gain matching.
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
68L QFN THIN.EPS
MAX12527
Dual, 65Msps, 12-Bit, IF/Baseband ADC
PACKAGE OUTLINE
68L THIN QFN, 10x10x0.8mm
21-0142
C
1
2
PACKAGE OUTLINE
68L THIN QFN, 10x10x0.8mm
21-0142
C
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
28 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.