TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS r r TAOS049E −SEPTEMBER 2007 D Integral Visible Light Cutoff Filter D Monolithic Silicon IC Containing D D D D D D D D D Photodiode, Operational Amplifier, and Feedback Components Converts Light Intensity to a Voltage High Irradiance Responsivity, Typically 111 mV/(W/cm2) at p = 940 nm (TSL260R) Compact 3-Lead Plastic Package Single Voltage Supply Operation Low Dark (Offset) Voltage....10mV Max Low Supply Current......1.1 mA Typical Wide Supply-Voltage Range.... 2.7 V to 5.5 V Replacements for TSL260, TSL261, and TSL262 RoHS Compliant (−LF Package Only) PACKAGE S SIDELOOKER (FRONT VIEW) 1 GND 1 GND Description PACKAGE SM SURFACE MOUNT SIDELOOKER (FRONT VIEW) 2 VDD 2 VDD 3 OUT 3 OUT The TSL260R, TSL261R, and TSL262R are infrared light-to-voltage optical sensors, each combining a photodiode and a transimpedance amplifier (feedback resistor = 16 MΩ, 8 MΩ, and 2.8 MΩ respectively) on a single monolithic IC. Output voltage is directly proportional to the light intensity (irradiance) on the photodiode. These devices have improved amplifier offset-voltage stability and low power consumption and are supplied in a 3-lead plastic sidelooker package with an integral visible light cutoff filter and lens. When supplied in the lead (Pb) free package, the device is RoHS compliant. Functional Block Diagram − + Voltage Output Available Options DEVICE TA PACKAGE − LEADS PACKAGE DESIGNATOR ORDERING NUMBER TSL260R 0°C to 70°C 3-lead Sidelooker S TSL260R TSL260R 0°C to 70°C 3-lead Sidelooker — Lead (Pb) Free S TSL260R−LF TSL260R 0°C to 70°C 3-lead Surface-Mount Sidelooker — Lead (Pb) Free TSL261R 0°C to 70°C 3-lead Sidelooker S TSL261R TSL261R 0°C to 70°C 3-lead Sidelooker — Lead (Pb) Free S TSL261R−LF TSL261R 0°C to 70°C 3-lead Surface-Mount Sidelooker — Lead (Pb) Free TSL262R 0°C to 70°C 3-lead Sidelooker S TSL262R TSL262R 0°C to 70°C 3-lead Sidelooker — Lead (Pb) Free S TSL262R−LF TSL262R 0°C to 70°C 3-lead Surface-Mount Sidelooker — Lead (Pb) Free The LUMENOLOGY r Company SM SM SM TSL260RSM−LF TSL261RSM−LF TSL262RSM−LF Copyright E 2007, TAOS Inc. r Texas Advanced Optoelectronic Solutions Inc. 1001 Klein Road S Suite 300 S Plano, TX 75074 S (972) r 673-0759 www.taosinc.com 1 TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 Terminal Functions TERMINAL NAME DESCRIPTION NO. GND 1 Ground (substrate). All voltages are referenced to GND. OUT 3 Output voltage VDD 2 Supply voltage Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 mA Duration of short-circuit current at (or below) 25°C (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 s Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25°C to 85°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25°C to 85°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds (S Package) . . . . . . . . . . . . . . . . . . . . 260°C Reflow solder, in accordance with J-STD-020C or J-STD-020D (SM Package) . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltages are with respect to GND. 2. Output may be shorted to supply. Recommended Operating Conditions MIN Supply voltage, VDD Operating free-air temperature, TA Copyright E 2007, TAOS Inc. 2 NOM MAX UNIT 2.7 5.5 V 0 70 °C The LUMENOLOGY r Company r www.taosinc.com r TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 Electrical Characteristics at VDD = 5 V, TA = 25°C, λp = 940 nm, RL = 10 kΩ (unless otherwise noted) (see Notes 3, 4, and 5) PARAMETER TSL260R TEST CONDITIONS MAX MIN TYP MAX MIN TYP MAX 10 0 4 10 0 4 10 3 3.3 3 3.3 1 2 1 2 Dark voltage Ee = 0 0 4 VOM Maximum output voltage VDD = 4.5 V 3 3.3 Ee = 18 μW/cm2 1 2 Output voltage αvo Ne IDD Temperature coefficient of output p voltage g (VO) Irradiance responsivity Supply pp y current V 3 8 mV/°C %/°C 8 mV/°C 0.4 %/°C 8 μW/cm2, Ee = 220 TA = 0°C to 70°C See Note 6 111 Ee = 18 μW/cm2 1.1 43.5 mV/°C 0.4 %/°C 9.1 mV/(μW/cm2) 1.7 μW/cm2 1.1 1.7 mA Ee = 220 μW/cm2 NOTES: 3. 4. 5. 6. V 0.4 Ee = 46 μW/cm2, TA = 0°C to 70°C Ee = 46 mV 3 μW/cm2 Ee = 18 μW/cm2, TA = 0°C to 70°C UNIT 3 Ee = 46 μW/cm2 Ee = 220 TSL262R TYP VD VO TSL261R MIN 1.1 1.7 Measurements are made with RL = 10 kΩ between output and ground. Optical measurements are made using small-angle incident radiation from an LED optical source. The input irradiance Ee is supplied by a GaAs LED with peak wavelength λp = 940 nm Irradiance responsivity is characterized over the range VO = 0.05 to 2.9 V. The best-fit straight line of Output Voltage VO versus irradiance Ee over this range will typically have a positive extrapolated VO value for Ee = 0. Dynamic Characteristics at TA = 25°C (see Figure 1) PARAMETER TSL260R TEST CONDITIONS MIN TYP TSL261R MAX MIN TYP TSL262R MAX MIN TYP MAX UNIT tr Output pulse rise time VDD = 5 V, λp = 940 nm 260 70 7 μs tf Output pulse fall time VDD = 5 V, λp = 940 nm 260 70 7 μs Output noise voltage VDD = 5 V, f = 1000 Hz Ee = 0, 0.8 0.7 0.6 Vn The LUMENOLOGY r Company μV/√Hz Copyright E 2007, TAOS Inc. r www.taosinc.com r 3 TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 PARAMETER MEASUREMENT INFORMATION VDD Pulse Generator Ee 2 LED (see Note A) Input − 3 + 90% RL TSL26xR 1 tf tr Output Output (see Note B) 10% 90% 10% VOLTAGE WAVEFORM TEST CIRCUIT NOTES: A. The input irradiance is supplied by a pulsed GaAs light-emitting diode with the following characteristics: λp = 940 nm, tr < 1 μs, tf < 1 μs. B. The output waveform is monitored on an oscilloscope with the following characteristics: tr < 100 ns, Zi ≥ 1 MΩ, Ci ≤ 20 pF. Figure 1. Switching Times TYPICAL CHARACTERISTICS NORMALIZED OUTPUT VOLTAGE vs ANGULAR DISPLACEMENT 1 TSL262R TSL261R TSL260R 0.6 Optical Axis VO − Normalized Output Voltage 0.8 0.4 0.2 0 80° 60° 40° 20° 0° 20° 40° θ − Angular Displacement 60° 80° Figure 2 Copyright E 2007, TAOS Inc. 4 The LUMENOLOGY r Company r www.taosinc.com r TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs IRRADIANCE VDD = 5 V λp = 940 nm RL = 10 k TA = 25°C PHOTODIODE SPECTRAL RESPONSIVITY 1 TSL261R TA = 25°C 0.8 TSL260R 1 Relative Responsivity VO — Output Voltage — V 10 TSL262R 0.1 0.6 0.4 0.2 0.01 0.1 1 10 100 0 1000 600 700 800 900 1000 λ − Wavelength − nm Ee — Irradiance — W/cm2 Figure 4 Figure 3 SUPPLY CURRENT vs OUTPUT VOLTAGE MAXIMUM OUTPUT VOLTAGE vs SUPPLY VOLTAGE 1.6 RL = 10 kΩ TA = 25°C 4 I DD − Supply Current − mA VOM − Maximum Output Voltage − V 5 3 2 1 0 2.5 1100 VDD = 5 V RL = 10 k TA = 25°C 1.4 1.2 1 0.8 3 4 4.5 3.5 VDD − Supply Voltage − V 5 5.5 0.6 0 1 Figure 5 The LUMENOLOGY r Company 2 3 VO − Output Voltage − V 4 Figure 6 Copyright E 2007, TAOS Inc. r www.taosinc.com r 5 TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 APPLICATION INFORMATION VDD 2 RP = 100 kΩ 3 TSL26xR Sensor Output 1 NOTE A: Pullup resistor extends linear output range to near VDD with minimal (several millivolts typical) effect on VDARK; particularly useful at low VDD (3 V to 5 V). Figure 7. Pullup for Increased VOM 5V 5V 2 100 Ω 5V TSL261R Sensor OP240† 4.7 kΩ 50-kΩ Threshold 3 10 kΩ 2 − 3 + 1 8 1 Output 4 LM393 15 kΩ 15 kΩ † OPTEK part number NOTE A: Output goes high when beam is interrupted; working distance is several inches or less. Intended for use as optical-interrupter switch or reflective-object sensor. Figure 8. Short-Range Optical Switch With Hysteresis Copyright E 2007, TAOS Inc. 6 The LUMENOLOGY r Company r www.taosinc.com r TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 APPLICATION INFORMATION 5V 5V 5V BN301† 27 kΩ 7 3 kΩ 6 4 2 8 TLC555 50 kΩ TSL262R Sensor 3 2N3906 2 1 3 2 8 4.7 kΩ 1 Output 4 TLC372 18 Ω 0.01 μF − 3 + 0.01 μF 1 5V 100 kΩ 15-kΩ Threshold † Stanley part number NOTE A: Output pulses low until beam is interrupted. Useful range is 1 ft to 20 ft; can be extended with lenses. This configuration is suited for object detection, safety guards, security systems, and automatic doors. Figure 9. Pulsed Optical-Beam Interrupter 6V 100 Ω 0.01 μF 2 OP295† or BN301 ‡ TSL260R Sensor Light Shield 3 560 kΩ 4 1 kΩ 3 8 0.1 μF 1 NE567 5 10 kΩ 2N3904 6 2 0.1 μF 1 270 kΩ 0.1 μF 1 μF + 7 + 4.7 μF † OPTEK part number Stanley part number NOTE A: Output goes low when light pulses from emitter are reflected back to sensor. Range is 6 in to 18 in depending upon object reflectance. Useful for automatic doors, annunciators, object avoidance in robotics, automatic faucets, and security systems. ‡ Figure 10. Proximity Detector The LUMENOLOGY r Company Copyright E 2007, TAOS Inc. r www.taosinc.com r 7 TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 APPLICATION INFORMATION S1 R3 22 Ω 9V R1 680 Ω 8 4 7 6 3 2 Q1 2N3904 R2 1 kΩ U1 TLC555 2 + D1 BN301† 3 5 C1 1 μF To Sensor 1 1 TRANSMITTER 6V 2 IN U4 TSL260R Sensor OUT J1 C5 0.1 μF COM 1 3 R5 7.5 kΩ R6 4.7 kΩ C2 0.1 μF 1 1 120 V 60 Hz 2 Q2 TIC225C 2 8 U2 NE567 6 U3 1 R7 4.7 kΩ 4 5 6 Freq Trim R4 180 Ω R8 300 Ω 6V 3 AC Load 6V 3 2 4 TIL3010 1 3 6V 2 7 + C3 1 μF 2 C4 4.7 μF + 4 PRE J VCC CLR U5 1/2 SN74HC76 CLK Q 1 16 3 5 K 15 R9 1 kΩ GND 13 Q3 2N3904 RECEIVER † OPTEK part number NOTE A: Single-channel remote control can be used to switch logic or light dc loads by way of U5 or ac loads by way of the optocoupler and triac as shown. Applications include ceiling fans, lamps, electric heaters, etc. Figure 11. IR Remote Control Copyright E 2007, TAOS Inc. 8 The LUMENOLOGY r Company r www.taosinc.com r TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 APPLICATION INFORMATION 6V 6V D1 OP295† IN U2 TLE2426 D2 OP295† 6V OUT U1 TLC271 COM 7 3 + Audio Input 5 + 2 _ 8 R1 10 kΩ C1 1 μF 6 Q1 2N3904 1 4 R3 40 Ω R2 20 kΩ TRANSMITTER 9V 2 IN U1 TSL261R Sensor OUT 3 + COM 1 9V R2 10 kΩ C3 1 μF C1 100 pF VOL 9V IN 2 U2 TLE2426 3 OUT COM R1 100 kΩ _ 7 + U3A 4 NE5534 6 + C2 47 μF Output (to headphones) RECEIVER † OPTEK part number NOTE A: Simple transmission of audio signal over short distances (<10 ft). Applications include wireless headphones, wireless-telephone headset, and wireless-headset intercom. Figure 12. IR Voice-Band Audio Link The LUMENOLOGY r Company Copyright E 2007, TAOS Inc. r www.taosinc.com r 9 TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 APPLICATION INFORMATION PCB Pad Layout Suggested PCB pad layout guidelines for the SM surface mount package are shown in Figure 16. 1.0 1.0 1.0 3.2 1.0 1.0 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. Figure 13. Suggested SM Package PCB Layout Copyright E 2007, TAOS Inc. 10 The LUMENOLOGY r Company r www.taosinc.com r TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 MECHANICAL DATA The TSL260R, TSL261R, and TSL262R are supplied in a clear 3-lead through-hole package with a molded lens. The integrated photodiode active area is typically 1,0 mm2 (0.0016 in2) for TSL260R, 0,5 mm2 (0.00078 in2) for the TSL261R, and 0,26 mm2 (0.0004 in2) for the TSL262R. PACKAGE S PLASTIC SINGLE-IN-LINE SIDE-LOOKER PACKAGE TOP VIEW 4.60 2.60 R 0.90 1.64 SIDE VIEW FRONT VIEW 2.30 0.15 Note B 1.80 4.60 1 1.56 0.42 14.86 + 0.50 Pb 2y2 NOTES: A. B. C. D. E. F. Lead Free Available 0.47 TYP 0.42 All linear dimensions are in millimeters; tolerance is ± 0.25 mm unless otherwise stated. Dimension is to center of lens arc, which is located below the package face. The integrated photodiode active area is typically located in the center of the lens and 0.97 mm below the top of the lens surface. Index of refraction of clear plastic is 1.55. Lead finish for TSL26xR: solder dipped, 63% Sn/37% Pb. Lead finish for TSL26xR−LF: solder dipped, 100% Sn. This drawing is subject to change without notice. Figure 14. Package S — Single-In-Line Side-Looker Package Configuration The LUMENOLOGY r Company Copyright E 2007, TAOS Inc. r www.taosinc.com r 11 TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 MECHANICAL DATA PACKAGE SM PLASTIC SURFACE MOUNT SIDE-LOOKER PACKAGE TOP VIEW 4.60 2.60 R 0.90 1.64 FRONT VIEW SIDE VIEW 0.15 Note B 2.30 1.80 4.60 0.62 + 0.10 1.00 1.97 0.42 0.62 +0.10 −0.15 5.73 + 0.50 Pb 2y2 NOTES: A. B. C. D. E. F. 2.59 0.47 TYP 0.42 Lead Free All linear dimensions are in millimeters; tolerance is ± 0.25 mm unless otherwise stated. Dimension is to center of lens arc, which is located below the package face. The integrated photodiode active area is typically located in the center of the lens and 0.97 mm below the top of the lens surface. Index of refraction of clear plastic is 1.55. Lead finish for TSL26xRSM−LF: solder dipped, 100% Sn. This drawing is subject to change without notice. Figure 15. Package SM — Surface Mount Side-Looker Package Configuration Copyright E 2007, TAOS Inc. 12 The LUMENOLOGY r Company r www.taosinc.com r TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 PRODUCTION DATA — information in this document is current at publication date. Products conform to specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard warranty. Production processing does not necessarily include testing of all parameters. LEAD-FREE (Pb-FREE) and GREEN STATEMENT Pb-Free (RoHS) TAOS’ terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material). Important Information and Disclaimer The information provided in this statement represents TAOS’ knowledge and belief as of the date that it is provided. TAOS bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TAOS has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TAOS and TAOS suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. NOTICE Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems. TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK. LUMENOLOGY, TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced Optoelectronic Solutions Incorporated. The LUMENOLOGY r Company Copyright E 2007, TAOS Inc. r www.taosinc.com r 13 TSL260R, TSL261R, TSL262R INFRARED LIGHT-TO-VOLTAGE OPTICAL SENSORS TAOS049E −SEPTEMBER 2007 Copyright E 2007, TAOS Inc. 14 The LUMENOLOGY r Company r www.taosinc.com r