CYPRESS CY8C22545

CY8C21345
CY8C22345, CY8C22545
PSoC® Programmable System-on-Chip
■
■
Powerful Harvard Architecture Processor:
❐ M8C Processor Speeds up to 24 MHz
❐ 8x8 Multiply, 32-Bit Accumulate
❐ Low Power at High Speed
❐ 3.0V to 5.25V Operating Voltage
❐ Industrial Temperature Range: -40°C to +85°C
High Speed 10-Bit SAR ADC with Sample and Hold Optimized
for Embedded Control
■
Precision, Programmable Clocking:
❐ Internal ± 5% 24/48 MHz Oscillator across the Industrial
Temperature Range
❐ High Accuracy 24 MHz with Optional 32 kHz Crystal and PLL
❐ Optional External Oscillator, up to 24 MHz
❐ Internal/External Oscillator for Watchdog and Sleep
■
Programmable Pin Configurations:
❐ 25 mA Sink, 10 mA Source on all GPIO
❐ Pull up, Pull down, High Z, Strong, or Open Drain Drive
Modes on all GPIO
❐ Up to 38 Analog Inputs on GPIO
❐ Configurable Interrupt on all GPIO
■
Additional System Resources:
2
❐ I C™ Slave, Master, and MultiMaster to 400 kHz
❐ Supports Hardware Addressing Feature
❐ Watchdog and Sleep Timers
❐ User Configurable Low Voltage Detection
❐ Integrated Supervisory Circuit
❐ On-Chip Precision Voltage Reference
❐ Supports RTC Block into Digital Peripheral Logic
Advanced Peripherals (PSoC® Blocks)
❐ Six Analog Type “E” PSoC Blocks Provide:
• Single or Dual 8-Bit ADC
• Comparators (up to four)
❐ Up to Eight Digital PSoC Blocks Provide:
• 8 to 32-Bit Timers, Counters, and PWMs
• One Shot, Multi Shot Mode Support in Timers and PWMs
• PWM with Deadband Support in One Digital Block
• Shift Register, CRC, and PRS Modules
• Full Duplex UART
• Multiple SPI Masters or Slaves, Variable Data Length
Support: 8 to 16-Bit
• Can be Connected to all GPIO Pins
❐ Complex Peripherals by Combining Blocks
❐ Shift Function Support for FSK Detection
❐ Powerful Synchronize Feature Support. Analog Module
Operations can be Synchronized by Digital Blocks or External
Signals.
■
■
■
Flexible On-Chip Memory:
❐ Up to 16K Bytes Flash Program Storage 50,000 Erase/Write
Cycles
❐ Up to 1K Byte SRAM Data Storage
❐ In-System Serial Programming (ISSP)
❐ Partial Flash Updates
❐ Flexible Protection Modes
❐ EEPROM Emulation in Flash
®
Optimized CapSense Resource:
❐ Two IDAC Support up to 640 µA Source Current to Replace
External Resistor
❐ Two Dedicated Clock Resources for CapSense:
• CSD_CLK: 1/2/4/8/16/32/128/256 Derive from SYSCLK
• CNT_CLK: 1/2/4/8 Derive from CSD_CLK
❐ Dedicated 16-Bit Timers/Counters for CapSense Scanning
❐ Support Dual CSD Channels Simultaneous Scanning
Cypress Semiconductor Corporation
Document Number: 001-43084 Rev. *L
•
198 Champion Court
Top Level Block Diagram
Port 4
Port 3
Port 2 Port 1 Port 0
Analog
Drivers
PSoC Core
Global Digital Interconnect
SRAM
1K
SROM
Global Analog Interconnect
Flash 16K
CPU Core (M8C)
Interrupt
Controller
Sleep and
Watchdog
Multiple Clock Sources
(Includes IMO, ILO, PLL, and ECO)
ANALOG SYSTEM
DIGITAL SYSTEM
Digital Block Array
Analog
Ref
Analog Input
Muxing(L,R)
DBC DBC DCC DCC
=
ROW 1
Analog Block Array
DBC DBC DCC DCC
ROW 2
System Bus
Features
CapSense
Digital Resource
Digital
Clocks
MACs
CTE
CTE
SCE
SCE
CTE
CTE
10-bit SAR
ADC
I2C
POR and LVD
System Resets
Internal
Voltage
Ref.
SYSTEM RESOURCES
•
San Jose, CA 95134-1709
•
408-943-2600
Revised December 17, 2010
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Contents
PSoC Functional Overview .............................................. 3
PSoC Core .................................................................. 3
Digital System ............................................................. 3
Analog System ............................................................ 4
Additional System Resources ..................................... 4
PSoC Device Characteristics ...................................... 5
Getting Started .................................................................. 6
Application Notes ........................................................ 6
Development Kits ........................................................ 6
Training ....................................................................... 6
CYPros Consultants .................................................... 6
Solutions Library .......................................................... 6
Technical Support ....................................................... 6
Development Tools .......................................................... 6
PSoC Designer Software Subsystems ........................ 6
In-Circuit Emulator ....................................................... 7
Designing with PSoC Designer ....................................... 7
Select Components ..................................................... 7
Configure Components ............................................... 7
Organize and Connect ................................................ 8
Generate, Verify, and Debug ....................................... 8
Pinouts .............................................................................. 9
CY8C22345, CY8C21345 28-Pin SOIC ...................... 9
CY8C22545 44-Pin TQFP ......................................... 10
Registers ......................................................................... 11
Register Conventions ................................................ 11
Register Mapping Tables .......................................... 11
Document Number: 001-43084 Rev. *L
Electrical Specifications ................................................ 14
Absolute Maximum Ratings ....................................... 15
Operating Temperature ............................................ 15
DC Electrical Characteristics ..................................... 16
AC Electrical Characteristics ..................................... 20
Packaging Information ................................................... 26
Thermal Impedances ................................................ 27
Solder Reflow Peak Temperature ............................. 27
Ordering Information ...................................................... 27
Ordering Code Definitions ........................................ 27
Acronyms ........................................................................ 28
Acronyms Used ......................................................... 28
Reference Documents .................................................... 28
Document Conventions ................................................. 29
Units of Measure ....................................................... 29
Numeric Conventions ................................................ 29
Glossary .......................................................................... 29
Document History Page ................................................. 34
Sales, Solutions, and Legal Information ...................... 35
Worldwide Sales and Design Support ....................... 35
Products .................................................................... 35
PSoC Solutions ......................................................... 35
Page 2 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
PSoC Functional Overview
The PSoC family consists of many On-Chip Controller devices.
These devices are designed to replace multiple traditional
MCU-based system components with one low cost single-chip
programmable device. PSoC devices include configurable
blocks of analog and digital logic, and programmable
interconnects. This architecture enables the user to create
customized peripheral configurations that match the
requirements of each individual application. Additionally, a fast
CPU, Flash program memory, SRAM data memory, and
configurable I/O are included in a range of convenient pinouts
and packages.
Digital System
The Digital System is composed of eight digital PSoC blocks.
Each block is an 8-bit resource that may be used alone or
combined with other blocks to form 8, 16, 24, and 32-bit
peripherals, which are called user module references.
Figure 1. Digital System Block Diagram
Port 3
To Analog
System
Row 0
DBC00
DBC01
DCC02
4
DCC03
4
Row Output
Configuration
Row Input
Configuration
Digital PSoC Block Array
8
8
8
Row Input
Configuration
8
The M8C CPU core is a powerful processor with speeds up to
24 MHz, providing a four MIPS 8-bit Harvard architecture microprocessor. The CPU uses an interrupt controller with 21 vectors,
to simplify the programming of real time embedded events.
Row 1
DBC00
GIE[7:0]
Program execution is timed and protected using the included
Sleep and Watch Dog Timers (WDT).
GIO[7:0]
DBC01
DCC02
DCC03
Global Digital
Interconnect
Row Output
Configuration
The PSoC Core is a powerful engine that supports a rich feature
set. The core includes a CPU, memory, clocks, and configurable
GPIO (General Purpose I/O).
PSoC GPIOs provide connection to the CPU, digital, and analog
resources of the device. Each pin’s drive mode may be selected
from eight options, allowing great flexibility in external
interfacing. Every pin can also generate a system interrupt on
high level, low level, and change from last read.
To System Bus
Port 0
DIGITAL SYSTEM
PSoC Core
The PSoC device incorporates flexible internal clock generators,
including a 24 MHz IMO (internal main oscillator). The 24 MHz
IMO can also be doubled to 48 MHz for use by the digital system.
A low power 32 kHz ILO (internal low speed oscillator) is
provided for the Sleep timer and WDT. If crystal accuracy is
required, the ECO (32.768 kHz external crystal oscillator) is
available for use as a Real Time Clock (RTC), and can optionally
generate a crystal-accurate 24 MHz system clock using a PLL.
The clocks, together with programmable clock dividers (as a
System Resource), provide the flexibility to integrate almost any
timing requirement into the PSoC device.
Port 2
Digital Clocks
From Core
The PSoC architecture, shown in Figure 1, consists of four main
areas: PSoC Core, Digital System, Analog System, and System
Resources. Configurable global busing allows the combining of
all the device resources into a complete custom system. The
PSoC family can have up to five I/O ports connecting to the
global digital and analog interconnects, providing access to eight
digital blocks and six analog blocks.
Memory encompasses 16 KB of Flash for program storage, 1K
bytes of SRAM for data storage, and up to 2 KB of EEPROM
emulated using the Flash. Program Flash uses four protection
levels on blocks of 64 bytes, allowing customized software IP
protection.
Port 1
Port 4
GOE[7:0]
GOO[7:0]
Digital peripheral configurations are:
■
PWMs (8 to 32-Bit)
■
PWMs with Dead band (8 to 32-Bit)
■
Counters (8 to 32-Bit)
■
Timers (8 to 32-Bit)
■
UART 8 Bit with Selectable Parity (Up to Two)
■
SPI Master and Slave (Up to Two)
■
Shift Register (1 to 32-Bit)
■
I2C Slave and Master (One Available as a System Resource)
■
Cyclical Redundancy Checker/Generator (8 to 32-Bit)
■
IrDA (Up to Two)
■
Pseudo Random Sequence Generators (8 to 32-Bit)
The digital blocks may be connected to any GPIO through a
series of global buses that can route any signal to any pin. The
buses also allow for signal multiplexing and performing logic
operations. This configurability frees your designs from the
constraints of a fixed peripheral controller.
Digital blocks are provided in rows of four, where the number of
blocks varies by PSoC device family. This provides a choice of
system resources for your application. Family resources are
shown in Table 1 on page 5.
Document Number: 001-43084 Rev. *L
Page 3 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Analog System
Additional System Resources
The Analog System consists of a 10-bit SAR ADC and six
configurable blocks.
System Resources, some of which are listed in the previous
sections, provide additional capability useful to complete
systems. Additional resources include a MAC, low voltage
detection, and power on reset. The merits of each system
resource are:
The programmable 10-bit SAR ADC is an optimized ADC that
can be run up to 200 ksps with ± 1.5 LSB DNL and ± 2.5 LSB INL
(true for VDD ≥ 3.0V and Vref ≥ 3.0V). External filters are required
on ADC input channels for antialiasing. This ensures that any
out-of-band content is not folded into the input signal band.
Reconfigurable analog resources allow creating complex analog
signal flows. Analog peripherals are very flexible and may be
customized to support specific application requirements. Some
of the more common PSoC analog functions (most available as
user modules) are:
■
Analog-to-Digital converters (Single or Dual, with 8-bit
resolution)
■
Pin-to-pin Comparator
■
Single ended comparators with absolute (1.3V) reference or
5-bit DAC reference
■
1.3V reference (as a System Resource)
Analog blocks are provided in columns of four, which include
CT-E (Continuous Time) and SC-E (Switched Capacitor) blocks.
These devices provide limited functionality Type “E” analog
blocks.
Figure 2. Analog System Block Diagram
■
Digital clock dividers provide three customizable clock
frequencies for use in applications. The clocks may be routed
to both the digital and analog systems. Additional clocks can
be generated using digital PSoC blocks as clock dividers.
■
Additional Digital resources and clocks optimized for CSD.
■
Support “RTC” block into digital peripheral logic.
■
A multiply accumulate (MAC) provides a fast 8-bit multiplier
with 32-bit accumulate, to assist in both general math and
digital filters.
■
The I2C module provides 100 and 400 kHz communication over
two wires. Slave, master, and multi-master modes are all
supported.
■
Low Voltage Detection (LVD) interrupts can signal the
application of falling voltage levels, while the advanced POR
(Power On Reset) circuit eliminates the need for a system
supervisor.
■
An internal 1.3V reference provides an absolute reference for
the analog system, including ADCs and DACs.
Array Input Configuration
ACI0[1:0]
ACI1[1:0]
ACI1[1:0]
ACI1[1:0]
ACE00
ACE01
ACE10
ACE11
ASE10
ASE11
Block Array
AmuxL
AmuxR
P0[0:7]
ACI2[3:0]
10 bit SAR ADC
Analog Reference
Interface to
Digital System
AGND
Reference
Generators
Bandgap
M8C Interface (Address Bus, Data Bus, Etc.)
Document Number: 001-43084 Rev. *L
Page 4 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
PSoC Device Characteristics
Depending on your PSoC device characteristics, the digital and analog systems can have 16, 8, or 4 digital blocks and 12, 6, or 3
analog blocks. The following table lists the resources available for specific PSoC device groups.
Table 1. PSoC Device Characteristics
PSoC Part
Number
Digital
I/O
CY8C29x66[1]
up to 64
CY8C28xxx
up to 44
Digital
Rows
Digital
Blocks
Analog
Inputs
Analog
Outputs
4
16
up to 12
4
up to 3
up to 12
up to 44
up to 4
Analog
Columns
Analog
Blocks
SRAM
Size
Flash
Size
4
12
2K
32 K
up to 6
up to
12 + 4[2]
1K
16 K
CY8C27x43
up to 44
2
8
up to 12
4
4
12
256
16 K
CY8C24x94[1]
up to 56
1
4
up to 48
2
2
6
1K
16 K
CY8C24x23A[1]
up to 24
1
4
up to 12
2
2
6
256
4K
CY8C23x33
up to 26
1
4
up to 12
2
2
4
256
8K
CY8C22x45[1]
up to 38
2
8
up to 38
0
4
6[2]
1K
16 K
CY8C21x45[1]
up to 24
1
4
up to 24
0
4
6[2]
512
8K
512
8K
256
4K
CY8C21x34[1]
up to 28
1
4
up to 28
0
2
4[2]
CY8C21x23
up to 16
1
4
up to 8
0
2
4[2]
512
8K
up to 2 K
up to 32 K
CY8C20x34[1]
up to 28
0
0
up to 28
0
0
3[2,3]
CY8C20xx6
up to 36
0
0
up to 36
0
0
3[2,3]
Notes
1. Automotive qualified devices available in this group.
2. Limited analog functionality.
3. Two analog blocks and one CapSense® block.
Document Number: 001-43084 Rev. *L
Page 5 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Getting Started
Development Tools
The quickest way to understand PSoC silicon is to read this data
sheet and then use the PSoC Designer Integrated Development
Environment (IDE). This data sheet is an overview of the PSoC
integrated circuit and presents specific pin, register, and
electrical specifications.
PSoC Designer is a Microsoft® Windows-based, integrated
development
environment
for
the
Programmable
System-on-Chip (PSoC) devices. The PSoC Designer IDE runs
on Windows XP or Windows Vista.
For in depth information, along with detailed programming
details, see the Technical Reference Manual for this PSoC
device.
For up-to-date ordering, packaging, and electrical specification
information, see the latest PSoC device data sheets on the web
at http://www.cypress.com.
Application Notes
Application notes are an excellent introduction to the wide variety
of possible PSoC designs and are available at
http://www.cypress.com.
Development Kits
PSoC Development Kits are available online from Cypress at
http://www.cypress.com and through a growing number of
regional and global distributors, which include Arrow, Avnet,
Digi-Key, Farnell, Future Electronics, and Newark.
Training
Free PSoC technical training (on demand, webinars, and
workshops) is available online at http://www.cypress.com. The
training covers a wide variety of topics and skill levels to assist
you in your designs.
CYPros Consultants
Certified PSoC Consultants offer everything from technical
assistance to completed PSoC designs. To contact or become a
PSoC Consultant go to http://www.cypress.com and refer to
CYPros Consultants.
Solutions Library
Visit our growing library of solution focused designs at
http://www.cypress.com. Here you can find various application
designs that include firmware and hardware design files that
enable you to complete your designs quickly.
Technical Support
For assistance with technical issues, search KnowledgeBase
articles and forums at http://www.cypress.com. If you cannot find
an answer to your question, call technical support at
1-800-541-4736.
Document Number: 001-43084 Rev. *L
This system provides design database management by project,
an integrated debugger with In-Circuit Emulator, in-system
programming support, and built-in support for third-party
assemblers and C compilers.
PSoC Designer also supports C language compilers developed
specifically for the devices in the PSoC family.
PSoC Designer Software Subsystems
System-Level View
A drag-and-drop visual embedded system design environment
based on PSoC Express. In the system level view you create a
model of your system inputs, outputs, and communication interfaces. You define when and how an output device changes state
based upon any or all other system devices. Based upon the
design, PSoC Designer automatically selects one or more PSoC
programmable system-on-chip controllers that match your
system requirements.
PSoC Designer generates all embedded code, then compiles
and links it into a programming file for a specific PSoC device.
Chip-Level View
The chip-level view is a more traditional integrated development
environment (IDE). Choose a base device to work with and then
select different onboard analog and digital components called
user modules that use the PSoC blocks. Examples of user
modules are ADCs, DACs, Amplifiers, and Filters. Configure the
user modules for your chosen application and connect them to
each other and to the proper pins. Then generate your project.
This prepopulates your project with APIs and libraries that you
can use to program your application.
The device editor also supports easy development of multiple
configurations and dynamic reconfiguration. Dynamic
configuration allows for changing configurations at run time.
Hybrid Designs
You can begin in the system-level view, allow it to choose and
configure your user modules, routing, and generate code, then
switch to the chip-level view to gain complete control over
on-chip resources. All views of the project share a common code
editor, builder, and common debug, emulation, and programming
tools.
Page 6 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Code Generation Tools
PSoC Designer supports multiple third party C compilers and
assemblers. The code generation tools work seamlessly within
the PSoC Designer interface and have been tested with a full
range of debugging tools. The choice is yours.
Assemblers. The assemblers allow assembly code to merge
seamlessly with C code. Link libraries automatically use absolute
addressing or are compiled in relative mode, and linked with
other software modules to get absolute addressing.
C Language Compilers. C language compilers are available
that support the PSoC family of devices. The products allow you
to create complete C programs for the PSoC family devices.
The optimizing C compilers provide all the features of C tailored
to the PSoC architecture. They come complete with embedded
libraries providing port and bus operations, standard keypad and
display support, and extended math functionality.
Debugger
The PSoC Designer Debugger subsystem provides hardware
in-circuit emulation, allowing you to test the program in a physical
system while providing an internal view of the PSoC device.
Debugger commands allow the designer to read and program
and read and write data memory, read and write I/O registers,
read and write CPU registers, set and clear breakpoints, and
provide program run, halt, and step control. The debugger also
allows the designer to create a trace buffer of registers and
memory locations of interest.
Designing with PSoC Designer
The development process for the PSoC device differs from that
of a traditional fixed function microprocessor. The configurable
analog and digital hardware blocks give the PSoC architecture a
unique flexibility that pays dividends in managing specification
change during development and by lowering inventory costs.
These configurable resources, called PSoC Blocks, have the
ability to implement a wide variety of user-selectable functions.
The PSoC development process can be summarized in the
following four steps:
1. Select components
2. Configure components
3. Organize and Connect
4. Generate, Verify, and Debug
Select Components
Both the system-level and chip-level views provide a library of
prebuilt, pretested hardware peripheral components. In the
system-level view, these components are called “drivers” and
correspond to inputs (a thermistor, for example), outputs (a
brushless DC fan, for example), communication interfaces
(I2C-bus, for example), and the logic to control how they interact
with one another (called valuators).
In the chip-level view, the components are called “user modules”.
User modules make selecting and implementing peripheral
devices simple, and come in analog, digital, and programmable
system-on-chip varieties.
Online Help System
Configure Components
The online help system displays online, context-sensitive help
for the user. Designed for procedural and quick reference, each
functional subsystem has its own context-sensitive help. This
system also provides tutorials and links to FAQs and an Online
Support Forum to aid the designer in getting started.
Each of the components you select establishes the basic register
settings that implement the selected function. They also provide
parameters and properties that allow you to tailor their precise
configuration to your particular application. For example, a Pulse
Width Modulator (PWM) User Module configures one or more
digital PSoC blocks, one for each 8 bits of resolution. The user
module parameters permit you to establish the pulse width and
duty cycle. Configure the parameters and properties to
correspond to your chosen application. Enter values directly or
by selecting values from drop down menus.
In-Circuit Emulator
A low cost, high functionality ICE (In-Circuit Emulator) is
available for development support. This hardware has the
capability to program single devices.
The emulator consists of a base unit that connects to the PC
using a USB port. The base unit is universal and operates with
all PSoC devices. Emulation pods for each device family are
available separately. The emulation pod takes the place of the
PSoC device in the target board and performs full speed
(24 MHz) operation.
Document Number: 001-43084 Rev. *L
Both the system-level drivers and chip-level user modules are
documented in data sheets that are viewed directly in the PSoC
Designer. These data sheets explain the internal operation of the
component and provide performance specifications. Each data
sheet describes the use of each user module parameter or driver
property, and other information you may need to successfully
implement your design.
Page 7 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Organize and Connect
You can build signal chains at the chip level by interconnecting
user modules to each other and the I/O pins, or connect system
level inputs, outputs, and communication interfaces to each
other with valuator functions.
In the system-level view, selecting a potentiometer driver to
control a variable speed fan driver and setting up the valuators
to control the fan speed based on input from the pot selects,
places, routes, and configures a programmable gain amplifier
(PGA) to buffer the input from the potentiometer, an analog to
digital converter (ADC) to convert the potentiometer’s output to
a digital signal, and a PWM to control the fan.
In the chip-level view, perform the selection, configuration, and
routing so that you have complete control over the use of all
on-chip resources.
Generate, Verify, and Debug
When you are ready to test the hardware configuration or move
on to developing code for the project, perform the “Generate
Application” step. This causes PSoC Designer to generate
source code that automatically configures the device to your
specification and provides the software for the system.
Document Number: 001-43084 Rev. *L
Both system-level and chip-level designs generate software
based on your design. The chip-level design provides application
programming interfaces (APIs) with high level functions to
control and respond to hardware events at run-time and interrupt
service routines that you can adapt as needed.
The system-level design also generates a C main() program that
completely controls the chosen application and contains placeholders for custom code at strategic positions allowing you to
further refine the software without disrupting the generated code.
A complete code development environment allows you to
develop and customize your applications in C, assembly
language, or both.
The last step in the development process takes place inside the
PSoC Designer’s Debugger subsystem. The Debugger
downloads the HEX image to the In-Circuit Emulator (ICE) where
it runs at full speed. Debugger capabilities rival those of systems
costing many times more. In addition to traditional single-step,
run-to-breakpoint and watch-variable features, the Debugger
provides a large trace buffer and allows you define complex
breakpoint events that include monitoring address and data bus
values, memory locations and external signals.
Page 8 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Pinouts
This PSoC device family is available in a variety of packages that are listed in the following tables. Every port pin (labeled with a “P”)
is capable of Digital I/O. However, Vss, Vdd, and XRES are not capable of Digital I/O.
CY8C22345, CY8C21345 28-Pin SOIC
Table 2. Pin Definitions
Pin No.
Type
Digital Analog
Pin Name
Description
1
I/O
I, MR
P0[7]
Integration Capacitor for MR
2
I/O
I, ML
P0[5]
Integration Capacitor for ML
3
I/O
I, ML
P0[3]
4
I/O
I, ML
P0[1]
5
I/O
I, ML
P2[7]
To Compare Column 0
6
I/O
ML
P2[5]
Optional ADC External Vref
7
I/O
ML
P2[3]
8
I/O
ML
P2[1]
9
Power
Vss
Ground Connection
10
I/O
ML
P1[7]
I2C Serial Clock (SCL)
I2C Serial Data (SDA)
11
I/O
ML
P1[5]
12
I/O
ML
P1[3]
13
I/O
ML
P1[1]
14
Power
Vss
15
I/O
MR
P1[0]
16
I/O
MR
P1[2]
17
I/O
MR
P1[4]
18
I/O
MR
P1[6]
19
Input
XRES
20
I/O
MR
21
I/O
MR
P2[2]
22
I/O
MR
P2[4]
23
I/O
I, MR
P2[6]
24
I/O
I, MR
P0[0]
25
I/O
I, MR
P0[2]
26
I/O
I, MR
P0[4]
27
I/O
I, MR
P0[6]
28
Power
Figure 3. Pin Diagram
AI, MR, P0[7]
AI, ML, P0[5]
AI, ML, P0[3]
AI, ML, P0[1]
AI, ML, P2[7]
ADC_Ext_Vref, ML, P2[5]
ML, P2[3]
ML, P2[1]
Vss
I2C SCL, ML, P1[7]
I2C SDA, ML, P1[5]
ML, P1[3]
I2C SCL, ML, P1[1]
Vss
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SOIC
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Vdd
P0[6], MR, AI
P0[4], MR, AI
P0[2], MR, AI
P0[0], MR, AI
P2[6], MR, AI
P2[4], MR
P2[2], MR
P2[0], MR
XRES
P1[6], MR
P1[4], MR, EXTCLK
P1[2], MR
P1[0], MR, I2C SDATA
I2C Serial Clock (SCL),
ISSP-SCLK[4]
Ground Connection
I2C Serial Clock (SCL),
ISSP-SDATA[4]
Optional External Clock Input
(EXT-CLK)
Active High Pin Reset with
Internal Pull Down
P2[0]
Vdd
To Compare Column 1
Supply Voltage
LEGEND: A = Analog, I = Input, O = Output, M=Analog Mux input, MR= Analog Mux right input, ML= Analog Mux left input.
Note
4. ISSP pin which is not Hi-Z at POR.
Document Number: 001-43084 Rev. *L
Page 9 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
CY8C22545 44-Pin TQFP
Table 3. Pin Definitions
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
17
18
I/O
Power
MR
Vss
P1[0]
19
I/O
MR
P1[2]
20
21
22
23
24
25
26
I/O
I/O
I/O
I/O
I/O
I/O
MR
MR
MR
MR
MR
MR
P1[4]
P1[6]
P3[0]
P3[2]
P3[4]
P3[6]
XRES
27
I/O
MR
P4[0]
28
I/O
MR
P4[2]
29
I/O
MR
P4[4]
Input
30
Power
Vss
31
I/O
MR
P2[0]
32
I/O
MR
P2[2]
33
I/O
MR
P2[4]
34
I/O
I, MR
P2[6]
35
I/O
I, MR
P0[0]
36
I/O
I, MR
P0[2]
37
I/O
I, MR
P0[4]
38
I/O
I, MR
P0[6]
39
Power
Ground Connection
I2C Serial Clock (SCL)
I2C Serial Data (SDA)
ADC_Ext_Vref, ML, P2[5]
ML, P2[3]
ML, P2[1]
Vdd
ML, P4[5]
ML, P4[3]
ML, P4[1]
Vss
ML, P3[7]
ML, P3[5]
ML, P3[3]
Crystal (XTALin), I2C Serial Clock (SCL),
TC SCLK[4]
Ground Connection
Crystal (XTALout), I2C
] Serial Data
(SDA), TC SDATA[4
1
2
3
4
5
TQFP
6
7
8
9
10
11
33
32
31
30
29
28
27
26
25
24
23
P2[4], MR
P2[2], MR
P2[0], MR
Vss
P4[4], MR
P4[2], MR
P4[0], MR
XRES
P3[6], MR
P3[4], MR
P3[2], MR
MR, P1[6]
MR, P3[0]
Power
Supply Voltage
P0[5], ML, AI
P0[7], MR, AI
Vdd
P0[6], MR, AI
P0[4], MR, AI
P0[2], MR, AI
P0[0], MR, AI
P2[6], MR, AI
ML
ML
ML
41
40
Power
I/O
I/O
I/O
Optional ADC External Vref
39
38
37
36
35
34
ML
ML
ML
ML
ML
ML
ML
ML
P2[5]
P2[3]
P2[1]
Vdd
P4[5]
P4[3]
P4[1]
Vss
P3[7]
P3[5]
P3[3]
P3[1]
P1[7]
P1[5]
P1[3]
P1[1]
Figure 4. Pin Diagram
P2[7], ML, AI
P0[1], ML, AI
P0[3], ML, AI
ML
ML
ML
Description
44
43
42
I/O
I/O
I/O
Pin Name
12
13
14
15
16
17
18
19
20
21
22
Analog
ML, P3[1]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Type
Digital
I2C SCL, ML, P1[7]
I2C SDA, ML, P1[5]
ML, P1[3]
I2C SCL, XTALin, ML, P1[1]
Vss
I2C SDA, XTALout, MR, P1[0]
MR, P1[2]
EXTCLK, MR, P1[4]
Pin No.
Optional External Clock Input (EXTCLK)
Active High Pin Reset with Internal Pull
Down
Ground Connection
To Compare Column 1
Vdd
Supply Voltage
40
I/O
I, MR
P0[7]
Integration Capacitor for MR
41
I/O
I, ML
P0[5]
Integration Capacitor for ML
42
I/O
I, ML
P0[3]
43
I/O
I, ML
P0[1]
44
I/O
I, ML
P2[7]
To Compare Column 0
LEGEND: A = Analog, I = Input, O = Output, M=Analog Mux input, MR= Analog Mux right input, ML= Analog Mux left input.
Document Number: 001-43084 Rev. *L
Page 10 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Registers
This section lists the registers of this PSoC device family by mapping tables. For detailed register information, refer the PSoC
Programmable System-on Chip Technical Reference Manual.
Register Conventions
Register Mapping Tables
Table 4. Abbreviations
The PSoC device has a total register address space of 512
bytes. The register space is also referred to as I/O space and is
broken into two parts. The XIO bit in the Flag register determines
which bank the user is currently in. When the XIO bit is set, the
user is said to be in the “extended” address space or the
“configuration” registers.
Convention
Description
RW
Read and write register or bit(s)
R
Read register or bit(s)
W
Write register or bit(s)
L
Logical register or bit(s)
C
Clearable register or bit(s)
#
Access is bit specific
Document Number: 001-43084 Rev. *L
Note In the following register mapping tables, blank fields are
Reserved and must not be accessed.
Page 11 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Table 5. Register Map Bank 0 Table: User Space
Name
PRT0DR
PRT0IE
PRT0GS
PRT0DM2
PRT1DR
PRT1IE
PRT1GS
PRT1DM2
PRT2DR
PRT2IE
PRT2GS
PRT2DM2
PRT3DR
PRT3IE
PRT3GS
PRT3DM2
PRT4DR
PRT4IE
PRT4GS
PRT4DM2
Addr (0,Hex) Access
Name
00
RW
01
RW
02
RW
03
RW
04
RW
05
RW
06
RW
07
RW
08
RW
09
RW
0A
RW
0B
RW
0C
RW
0D
RW
0E
RW
0F
RW
10
RW
CSD0_DR0_L
11
RW
CSD0_DR1_L
12
RW
CSD0_CNT_L
13
RW
CSD0_CR0
14
RW
CSD0_DR0_H
15
RW
CSD0_DR1_H
16
RW
CSD0_CNT_H
17
RW
CSD0_CR1
18
RW
CSD1_DR0_L
19
RW
CSD1_DR1_L
1A
RW
CSD1_CNT_L
1B
RW
CSD1_CR0
1C
RW
CSD1_DR0_H
1D
RW
CSD1_DR1_H
1E
RW
CSD1_CNT_H
1F
RW
CSD_CR1
DBC00DR0
20
#
AMX_IN
DBC00DR1
21
W
AMUX_CFG
DBC00DR2
22
RW
PWM_CR
DBC00CR0
23
#
ARF_CR
DBC01DR0
24
#
CMP_CR0
DBC01DR1
25
W
ASY_CR
DBC01DR2
26
RW
CMP_CR1
DBC01CR0
27
#
DCC02DR0
28
#
ADC0_CR
DCC02DR1
29
W
ADC1_CR
DCC02DR2
2A
RW
SADC_DH
DCC02CR0
2B
#
SADC_DL
DCC03DR0
2C
#
TMP_DR0
DCC03DR1
2D
W
TMP_DR1
DCC03DR2
2E
RW
TMP_DR2
DCC03CR0
2F
#
TMP_DR3
DBC10DR0
30
#
DBC10DR1
31
W
DBC10DR2
32
RW
ACB00CR1*
DBC10CR0
33
#
ACB00CR2*
DBC11DR0
34
#
DBC11DR1
35
W
DBC11DR2
36
RW
ACB01CR1*
DBC11CR0
37
#
ACB01CR2*
DCC12DR0
38
#
DCC12DR1
39
W
DCC12DR2
3A
RW
DCC12CR0
3B
#
DCC13DR0
3C
#
DCC13DR1
3D
W
DCC13DR2
3E
RW
DCC13CR0
3F
#
Shaded fields are Reserved and must not be accessed.
Document Number: 001-43084 Rev. *L
Addr (0,Hex)
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72*
73*
74
75
76*
77*
78
79
7A
7B
7C
7D
7E
7F
Access
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
R
W
R
#
R
W
R
RW
R
W
R
#
R
W
R
RW
RW
RW
RW
RW
#
#
RW
RW
#
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
ASC10CR0*
Addr (0,Hex) Access
Name
80*
RW
81
RW
82
RW
83
RW
ASD11CR0*
84*
RW
85
RW
86
RW
87
RW
88
RW
PWMVREF0
89
RW
PWMVREF1
8A
RW
IDAC_MODE
8B
RW
PWM_SRC
8C
RW
TS_CR0
8D
RW
TS_CMPH
8E
RW
TS_CMPL
8F
RW
TS_CR1
90
RW
CUR PP
91
RW
STK_PP
92
RW
PRV PP
93
RW
IDX_PP
94
RW
MVR_PP
95
RW
MVW_PP
96
RW
I2C0_CFG
97
RW
I2C0_SCR
98
RW
I2C0_DR
99
RW
I2C0_MSCR
9A
RW
INT_CLR0
9B
RW
INT_CLR1
9C
RW
INT_CLR2
9D
RW
INT_CLR3
9E
RW
INT_MSK3
9F
RW
INT_MSK2
A0
INT_MSK0
A1
INT_MSK1
A2
INT_VC
A3
RES_WDT
A4
DEC_DH
A5
DEC_DL
A6
DEC _CR0*
A7
DEC_CR1*
A8
W
MUL0_X
A9
W
MUL0_Y
AA
R
MUL0_DH
AB
R
MUL0_DL
AC
RW
ACC0_DR1
AD
RW
ACC0_DR0
AE
RW
ACC0_DR3
AF
RW
ACC0_DR2
RDI0RI
B0
RW
CPU A
RDI0SYN
B1
RW
CPU_T1
RDI0IS
B2
RW
CPU_T2
RDI0LT0
B3
RW
CPU_X
RDI0LT1
B4
RW
CPU PCL
RDI0RO0
B5
RW
CPU_PCH
RDI0RO1
B6
RW
CPU_SP
RDI0DSM
B7
RW
CPU_F
RDI1RI
B8
RW
CPU_TST0
RDI1SYN
B9
RW
CPU_TST1
RDI1IS
BA
RW
CPU_TST2
RDI1LT0
BB
RW
CPU TST3
RDI1LT1
BC
RW
DAC1_D
RDI1RO0
BD
RW
DAC0_D
RDI1RO1
BE
RW
CPU_SCR1
RDI1DSM
BF
RW
CPU_SCR0
# Access is bit specific. * has a different meaning.
Addr (0,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Access
RW
RW
RW
RW
RW
RW
RW
RW
#
#
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
#
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RC
W
RW
RW
RW
RW
W
W
R
R
RW
RW
RW
RW
#
#
#
#
#
#
#
I
RW
RW
RW
#
RW
RW
#
#
Page 12 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Table 6. Register Map Bank 1 Table: Configuration Space
Name
PRT0DM0
PRT0DM1
PRT0IC0
PRT0IC1
PRT1DM0
PRT1DM1
PRT1IC0
PRT1IC1
PRT2DM0
PRT2DM1
PRT2IC0
PRT2IC1
PRT3DM0
PRT3DM1
PRT3IC0
PRT3IC1
PRT4DM0
PRT4DM1
PRT4IC0
PRT4IC1
DBC00FN
DBC00IN
DBC00OU
DBC00CR1
DBC01FN
DBC01IN
DBC01OU
DBC01CR1
DCC02FN
DCC02IN
DCC02OU
DBC02CR1
Addr (1,Hex)
0
1
2
3
4
5
6
7
8
9
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
CMP0CR1
CMP0CR2
VDAC50CR0
CMP1CR1
CMP1CR2
VDAC51CR0
CSCMPCR0
CSCMPGOEN
CSLUTCR0
CMPCOLMUX
CMPPWMCR
CMPFLTCR
CMPCLK1
CMPCLK0
CLK_CR0
CLK_CR1
ABF_CR0
AMD_CR0
CMP_GO_EN
CMP_GO_EN1
AMD_CR1
ALT_CR0
ALT_CR1
CLK_CR2
CLK_CR3
DCC03FN
2C
RW
TMP_DR0
DCC03IN
2D
RW
TMP_DR1
DCC03OU
2E
RW
TMP_DR2
DBC03CR1
2F
RW
TMP_DR3
DBC10FN
30
RW
DBC10IN
31
RW
DBC10OU
32
RW
ACB00CR1*
DBC10CR1
33
RW
ACB00CR2*
DBC11FN
34
RW
DBC11IN
35
RW
DBC11OU
36
RW
ACB01CR1*
DBC11CR1
37
RW
ACB01CR2*
DCC12FN
38
RW
DCC12IN
39
RW
DCC12OU
3A
RW
DBC12CR1
3B
RW
DCC13FN
3C
RW
DCC13IN
3D
RW
DCC13OU
3E
RW
DBC13CR1
3F
RW
Shaded fields are Reserved and must not be accessed.
Document Number: 001-43084 Rev. *L
Addr (1,Hex)
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
6C
6D
6E
6F
70
71
72
73
74
75
76*
77*
78
79
7A
7B
7C
7D
7E
7F
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
ASC10CR0*
Addr (1,Hex) Access Name
80*
RW
81
RW
82
RW
83
RW
ASD11CR0*
84*
RW
85
RW
86
RW
87
RW
88
RW
89
RW
8A
RW
8B
RW
8C
RW
8D
RW
8E
RW
8F
RW
90
RW
GDI_O_IN
91
RW
GDI_E_IN
92
RW
GDI_O_OU
93
RW
GDI_E_OU
94
RW
95
RW
96
RW
97
RW
98
RW
MUX_CR0
99
RW
MUX_CR1
9A
RW
MUX_CR2
9B
RW
MUX_CR3
9C
RW
DAC_CR1#
9D
RW
OSC_GO_EN
9E
RW
OSC_CR4
9F
RW
OSC_CR3
GDI_O_IN_CR A0
RW
OSC_CR0
GDI_E_IN_CR
A1
RW
OSC_CR1
GDI_O_OU_CR A2
RW
OSC_CR2
GDI_E_OU_CR A3
RW
VLT_CR
RTC_H
A4
RW
VLT_CMP
RTC_M
A5
RW
ADC0_TR*
RTC_S
A6
RW
ADC1_TR*
RTC_CR
A7
RW
V2BG_TR
SADC_CR0
A8
RW
IMO_TR
SADC_CR1
A9
RW
ILO_TR
SADC_CR2
AA
RW
BDG_TR
SADC_CR3TRI AB
RW
ECO_TR
M
SADC_CR4
AC
RW
MUX_CR4
I2C0_AD
AD
RW
MUX_CR5
AE
RW
MUX_CR6
AF
RW
MUX_CR7
RDI0RI
B0
RW
CPU A
RDI0SYN
B1
RW
CPU_T1
RDI0IS
B2
RW
CPU_T2
RDI0LT0
B3
RW
CPU_X
RDI0LT1
B4
RW
CPU_PCL
RDI0RO0
B5
RW
CPU_PCH
RDI0RO1
B6
RW
CPU_SP
RDI0DSM
B7
RW
CPU_F
RDI1RI
B8
RW
FLS_PR0
RDI1SYN
B9
RW
FLS TR
RDI1IS
BA
RW
FLS_PR1
RDI1LT0
BB
RW
RDI1LT1
BC
RW
FAC_CR0
RDI1RO0
BD
RW
DAC_CR0#
RDI1RO1
BE
RW
CPU_SCR1
RDI1DSM
BF
RW
CPU_SCR0
# Access is bit specific. * has a different meaning.
Addr (1,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
Access
RW
RW
RW
RW
RW
RW
RW
RW
#
RW
RW
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
R
RW
RW
RW
W
W
RW
W
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
RW
RW
RW
RW
#
#
#
#
#
#
#
I
RW
W
RW
SW
RW
#
#
Page 13 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Electrical Specifications
This section presents the DC and AC electrical specifications of this PSoC device family. For the latest electrical specifications, check
the most recent data sheet by visiting http://www.cypress.com.
Specifications are valid for -40°C ≤ TA ≤ 85°C and TJ ≤ 100°C, except where noted. Specifications for devices running at greater than
12 MHz are valid for -40°C ≤ TA ≤ 70°C and TJ ≤ 82°C.
Figure 5. Voltage versus Operating Frequency
5.25
Vdd Voltage
lid n g
Va rati n
e io
Op Reg
4.75
3.00
93 kHz
12 MHz
24 MHz
CPU Frequency
Document Number: 001-43084 Rev. *L
Page 14 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Absolute Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 7. Absolute Maximum Ratings
Symbol
TSTG
Description
Storage Temperature
TBAKETEMP
Bake Temperature
TBAKETIME
Bake Time
Min
-55
Typ
–
Max
+100
-
125
See Package
label
72
Hours
-
Units
Notes
°C
Higher storage temperatures reduce data
retention time
o
C
TA
See package
label
Ambient Temperature with Power Applied
-40
–
+85
°C
Vdd
Supply Voltage on Vdd Relative to Vss
-0.5
–
+6.0
V
VIO
DC Input Voltage
Vss - 0.5
–
Vdd + 0.5
V
VIOz
DC Voltage Applied to Tristate
Vss - 0.5
–
Vdd + 0.5
V
IMIO
Maximum Current into any Port Pin
ESD
Electro Static Discharge Voltage
LU
Latch up Current
-25
–
+50
mA
2000
–
–
V
–
–
200
mA
Min
-40
-40
Typ
–
–
Max
+85
+100
Human Body Model
ESD
Operating Temperature
Table 8. Operating Temperature
Symbol
TA
TJ
Description
Ambient Temperature
Junction Temperature
Document Number: 001-43084 Rev. *L
Units
Notes
°C
°C
The temperature rise
from ambient to junction
is package specific. See
Table 29 on page 27. The
user must limit the power
consumption to comply
with this requirement.
Page 15 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
DC Electrical Characteristics
DC Chip Level Specifications
Table 9 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V and 3.3V at 25°C, and are for design
guidance only, unless specified otherwise.
Table 9. DC Chip Level Specifications
Symbol
Vdd
Description
Supply Voltage
Min
3.0
Typ
–
Max
5.25
IDD
Supply Current
–
7
12
mA
IDD3
Supply Current
–
4
7
mA
ISB
Sleep (Mode) Current with POR, LVD,
Sleep Timer, and WDT[5]
–
3
6.5
μA
ISBH
Sleep (Mode) Current with POR, LVD,
Sleep Timer, and WDT at high
temperature[5]
Sleep (Mode) Current with POR, LVD,
Sleep Timer, WDT, and external crystal[5]
–
4
25
μA
–
4
7.5
μA
Sleep (Mode) Current with POR, LVD,
Sleep Timer, WDT, and external crystal at
high temperature [5]
Reference Voltage (Bandgap)
–
5
26
μA
1.275
1.3
1.325
V
ISBXTL
ISBXTLH
VREF
Units
Notes
V
See Table 16 on page 18
Conditions are Vdd = 5.0V,
25°C, CPU = 3 MHz, 48 MHz disabled.
VC1 = 1.5 MHz
VC2 = 93.75 kHz
VC3 = 93.75 kHz
Conditions are Vdd = 3.3V
TA = 25°C, CPU = 3 MHz
48 MHz = Disabled
VC1 = 1.5 MHz, VC2 = 93.75 kHz
VC3 = 93.75 kHz
Conditions are with internal slow speed
oscillator, Vdd = 3.3V
-40°C <= TA <= 55°C
Conditions are with internal slow speed
oscillator, Vdd = 3.3V
55°C < TA <= 85°C
Conditions are with properly loaded,
1 μW max, 32.768 kHz crystal.
Vdd = 3.3V, -40°C <= TA <= 55°C
Conditions are with properly loaded,
1μW max, 32.768 kHz crystal.
Vdd = 3.3 V, 55°C < TA <= 85°C
Trimmed for appropriate Vdd
DC GPIO Specifications
Table 10 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V and 3.3V at 25°C and are for design
guidance only, unless otherwise specified.
Table 10. DC GPIO Specifications
Symbol
RPU
Description
Pull up Resistor
Min
4
Typ
5.6
RPD
VOH
Max
8
Units
kΩ
Pull down Resistor
4
High Output Level
Vdd - 1.0
5.6
8
kΩ
–
–
V
VOL
Low Output Level
–
–
0.75
V
IOH
High Level Source Current
10
–
–
mA
Notes
IOH = 10 mA, Vdd = 4.75 to 5.25V
(80 mA maximum combined IOH
budget)
IOL = 25 mA, Vdd = 4.75 to 5.25V
(100 mA maximum combined IOL
budget)
VOH = Vdd-1.0V, see the limitations of
the total current in the note for VOH.
Note
5. Standby current includes all functions (POR, LVD, WDT, Sleep Time) needed for reliable system operation. This must be compared with devices that have similar
functions enabled.
Document Number: 001-43084 Rev. *L
Page 16 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Table 10. DC GPIO Specifications (continued)
Symbol
IOL
Description
Low Level Sink Current
Min
25
Typ
–
Max
–
Units
mA
Input Low Level
–
–
0.8
V
Notes
VOL = 0.75V, see the limitations of the
total current in the note for VOL.
Vdd = 3.0 to 5.25
VIL
V
Vdd = 3.0 to 5.25
–
mV
VIH
Input High Level
2.1
–
VH
Input Hysterisis
–
60
IIL
Input Leakage (Absolute Value)
–
1
–
nA
Gross tested to 1 μA
CIN
Capacitive Load on Pins as Input
–
3.5
10
pF
COUT
Capacitive Load on Pins as Output
–
3.5
10
pF
Package and pin dependent.
Temp = 25°C
Package and pin dependent.
Temp = 25°C
DC Operational Amplifier Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C respectively. Typical parameters apply to 5V or 3.3V at 25°C and are for
design guidance only.
Table 11. 5V DC Operational Amplifier Specifications
Symbol
VOSOA
Description
Input Offset Voltage (absolute value)
TCVOSOA Average Input Offset Voltage Drift
Min
–
Typ
2.5
Max
15
Units
mV
–
10
–
μV/°C
Notes
IEBOA[6]
Input Leakage Current (Port 0 Analog Pins)
–
200
–
pA
Gross tested to 1 μA
CINOA
Input Capacitance (Port 0 Analog Pins)
–
4.5
9.5
pF
Package and pin dependent.
Temp = 25°C
VCMOA
Common Mode Voltage Range
0.0
–
Vdd - 1
V
Min
Typ
Max
Units
Table 12. 3.3V DC Operational Amplifier Specifications
Symbol
Description
Notes
VOSOA
Input Offset Voltage (absolute value)
–
2.5
15
mV
TCVOSOA
Average Input Offset Voltage Drift
–
10
–
μV/°C
IEBOA[6]
Input Leakage Current (Port 0 Analog Pins)
–
200
–
pA
Gross tested to 1 μA
CINOA
Input Capacitance (Port 0 Analog Pins)
–
4.5
9.5
pF
Package and pin dependent.
Temp = 25°C
VCMOA
Common Mode Voltage Range
0
–
Vdd – 1
V
DC Low Power Comparator Specifications
Table 13 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C, 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C respectively. Typical parameters apply to 5V at 25°C and are for design guidance only.
Table 13. DC Low Power Comparator Specifications
Symbol
VREFLPC
VOSLPC
Description
Low power comparator (LPC) reference
voltage range
LPC voltage offset
Min
0.2
Typ
–
Max
Vdd - 1
Units
V
–
2.5
30
mV
Notes
Note
6. Atypical behavior: IEBOA of Port 0 Pin 0 is below 1 nA at 25°C; 50 nA over temperature. Use Port 0 Pins 1-7 for the lowest leakage of 200 nA.
Document Number: 001-43084 Rev. *L
Page 17 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
SAR10 ADC DC Specifications
Table 14 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V at 25°C and are for design
guidance only.
Table 14. SAR10 ADC DC Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
Vadcvref
Reference voltage at pin P2[5] when configured
as ADC reference voltage
3.0
–
5.25
V
When VREF is buffered inside
ADC, the voltage level at P2[5]
(when configured as ADC
reference voltage) must be
always maintained to be at least
300 mV less than the chip supply
voltage level on Vdd pin.
(Vadcvref < Vdd)
Iadcvref
Current when P2[5] is configured as ADC VREF
-
–
0.5
mA
Disables the internal voltage
reference buffer
INL at 10 bits
Integral Nonlinearity
-2.5
–
2.5
LSB
For VDD ≥ 3.0V and Vref ≥ 3.0V
-5.0
–
5.0
LSB
For VDD < 3.0V or Vref < 3.0V
DNL at 10 bits Differential Nonlinearity
SPS
Sample per second
-1.5
–
1.5
LSB
For VDD≥ 3.0V and Vref ≥ 3.0V
-4.0
–
4.0
LSB
For VDD < 3.0V or Vref < 3.0V
–
–
150
ksps Resolution 10 bits
DC Analog Mux Bus Specifications
Table 15 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V at 25°C and are for design
guidance only.
Table 15. DC Analog Mux Bus Specifications
Symbol
Description
Min
Typ
Max
Units
RSW
Switch Resistance to Common Analog Bus
–
–
400
Ω
Rgnd
Resistance of Initialization Switch to gnd
–
–
800
Ω
Notes
Vdd ≥ 3.00
DC POR and LVD Specifications
Table 16 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V at 25°C and are for design
guidance only.
Table 16. DC POR and LVD Specifications
Symbol
Description
VPPOR1
VPPOR2
Vdd Value for PPOR Trip
PORLEV[1:0] = 01b
PORLEV[1:0] = 10b
VLVD2
VLVD3
VLVD4
VLVD5
VLVD6
VLVD7
Vdd Value for LVD Trip
VM[2:0] = 010b
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b
VM[2:0] = 111b
Document Number: 001-43084 Rev. *L
Min
Typ
Max
Units
–
2.82
4.55
2.95
4.70
V
V
2.95
3.06
4.37
4.50
4.62
4.71
3.02
3.13
4.48
4.64
4.73
4.81
3.09
3.20
4.55
4.75
4.83
4.95
V
V
V
V
V
V
Notes
Vdd must be greater than or
equal to 3.0V during startup,
reset from the XRES pin, or
reset from Watchdog.
Page 18 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
DC Programming Specifications
Table 17 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V at 25°C and are for design
guidance only.
Table 17. DC Programming Specifications
Min
Typ
Max
Units
Notes
VDDP
Symbol
VDD for programming and erase
Description
4.5
5.0
5.5
V
VDDLV
Low VDD for verify
3.0
3.1
3.2
V
VDDHV
High VDD for verify
5.1
5.2
5.3
V
VDDIWRITE
Supply voltage for flash write operation
3.0
–
5.25
V
This specification applies to the
functional requirements of
external programmer tools
This specification applies to the
functional requirements of
external programmer tools
This specification applies to the
functional requirements of
external programmer tools
This specification applies to this
device when it is executing
internal flash writes
IDDP
Supply Current during Programming or Verify
–
5
25
mA
Input Low Voltage during Programming or
Verify
VIHP
Input High Voltage during Programming or
Verify
IILP
Input Current when Applying Vilp to P1[0] or
P1[1] during Programming or Verify
IIHP
Input Current when Applying Vihp to P1[0] or
P1[1] during Programming or Verify
VOLV
Output Low Voltage during Programming or
Verify
VOHV
Output High Voltage during Programming or
Verify
FlashENPB Flash Endurance (per block)[8]
FlashENT Flash Endurance (total)[7]
–
–
0.8
V
2.2
–
–
V
–
–
0.2
mA
–
–
1.5
mA
–
–
Vss + 0.75
V
Vdd - 1.0
–
Vdd
V
VILP
FlashDR
Flash Data Retention
Driving internal pull down
resistor
Driving internal pull down
resistor
50,000
–
–
–
Erase/write cycles per block
1,800,000
–
–
–
Erase/write cycles
10
–
–
Years
DC I2C Specifications
Table 18 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V at 25°C and are for design
guidance only.
Table 18. DC I2C Specifications
Parameter
VILI2C[9]
VIHI2C[9]
Description
Min
Typ
Max
Units
Notes
Input low level
–
–
0.3 × VDD
V
–
–
0.25 × VDD
V
4.75 V ≤ VDD ≤ 5.25 V
Input high level
0.7 × VDD
–
–
V
3.0 V ≤ VDD ≤ 5.25 V
3.0 V ≤ VDD ≤ 3.6 V
Note
7. A maximum of 36 x 50,000 block endurance cycles is allowed. This may be balanced between operations on 36x1 blocks of 50,000 maximum cycles each, 36x2
blocks of 25,000 maximum cycles each, or 36x4 blocks of 12,500 maximum cycles each (to limit the total number of cycles to 36x50,000 and that no single block
ever sees more than 50,000 cycles).
For the full industrial range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing.
Refer to the Flash APIs Application Note AN2015 at http://www.cypress.com under Application Notes for more information.
8. The 50,000 cycle Flash endurance per block is guaranteed only if the Flash operates within one voltage range. Voltage ranges are 3.0V to 3.6V and 4.75V to 5.25V
9. All GPIOs meet the DC GPIO VIL and VIH specifications found in the DC GPIO specifications sections.The I2C GPIO pins also meet the above specs.
Document Number: 001-43084 Rev. *L
Page 19 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
AC Electrical Characteristics
AC Chip Level Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V at 25°C and are
for design guidance only.
Table 19. 5V and 3.3V AC Chip-Level Specifications
Symbol
FIMO24
Description
Internal Main Oscillator Frequency for 24 MHz
FIMO6
Internal Main Oscillator Frequency for 6 MHz
FCPU1
CPU Frequency (5V Nominal)
FCPU2
CPU Frequency (3.3V Nominal)
FBLK5
Min
22.8
Min(%) Typ
Max
Max(%) Units
Notes
–
24 25.2[10,11
–
MHz Trimmed for 5V or 3.3V
,12]
operation using factory trim
values. See Figure 5 on
page 14. SLIMO mode = 0 <
85
[10,11,
5.5
6
MHz
Trimmed for 5V or 3.3V
8
6.5
8
12]
operation using factory trim
values. See Figure 5 on
page 14.
SLIMO mode = 0 < 85.
0.089
–
24 24.6[10,11
–
MHz 24 MHz only for
]
SLIMO mode = 0.
0.089
–
12
12.3[11,12
–
MHz SLIMO mode = 0.
Digital PSoC Block Frequency0(5V Nominal)
0
–
48
49.2[10,11
–
MHz Refer to Table 23 on page
22.
FBLK33
Digital PSoC Block Frequency (3.3V Nominal)
0
–
24
24.6[11,13
–
MHz
F32K1
Internal Low Speed Oscillator Frequency
15
–
32
85
–
kHz
F32KU
Untrimmed Internal Low Speed Oscillator
Frequency
5
–
–
100
–
TXRST
External Reset Pulse Width
10
–
–
–
–
kHz The ILO is not adjusted with
the factory trim values until
after the CPU starts running.
See the “System Resets”
section in the Technical
Reference Manual.
µs
DC24M
DCILO
FOUT48M
24 MHz Duty Cycle
Internal Low Speed Oscillator Duty Cycle
48 MHz Output Frequency
40
20
46.8
–
–
–
50
50
48.0
60
80
49.2
–
–
–
Maximum frequency of signal on row input or
row output
SRPOWERUP Power supply slew rate
–
–
–
12.3
–
–
–
–
250
–
TPOWERUP
Time from end of POR to CPU executing code
–
–
–
100
–
24 MHz IMO cycle-to-cycle jitter (RMS)
24 MHz IMO long term N cycle-to-cycle jitter
(RMS)
24 MHz IMO period jitter (RMS)
–
–
–
–
200
300
700
900
–
–
ps
ps
–
–
100
400
–
ps
24 MHz IMO cycle-to-cycle jitter (RMS)
24 MHz IMO long term N cycle-to-cycle jitter
(RMS)
24 MHz IMO period jitter (RMS)
–
–
–
–
200
300
800
1200
–
–
ps
ps
–
–
100
700
–
ps
FMAX
tjit_IMO
[14]
tjit_PLL [14]
]
,13]
]
%
%
MHz Trimmed. Utlizing factory
trim values.
MHz
V/ms Vdd slew rate during power
up.
ms
N = 32
N = 32
Notes
10. Valid only for 4.75V < Vdd < 5.25V.
11. Accuracy derived from Internal Main Oscillator with appropriate trim for Vdd range.
12. 3.0V < Vdd < 3.6V. See Application Note AN2012 “Adjusting PSoC Microcontroller Trims for Dual Voltage-Range Operation” for information on trimming for operation
at 3.3V.
13. Refer to the individual user module data sheets for information on maximum frequencies for user modules.
14. Refer to Cypress Jitter Specifications application note, Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 for more information.
Document Number: 001-43084 Rev. *L
Page 20 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
AC GPIO Specifications
Table 20 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V at 25°C and are for design
guidance only.
Table 20. 5V and 3.3V AC GPIO Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
FGPIO
GPIO Operating Frequency
0
–
12
MHz
TRiseF
Rise Time, Normal Strong Mode, Cload = 50 pF
3
–
18
ns
Normal Strong Mode
Vdd = 4.5 to 5.25V, 10% - 90%
TFallF
Fall Time, Normal Strong Mode, Cload = 50 pF
2
–
18
ns
Vdd = 4.5 to 5.25V, 10% - 90%
TRiseS
Rise Time, Slow Strong Mode, Cload = 50 pF
7
27
–
ns
Vdd = 3 to 5.25V, 10% - 90%
TFallS
Fall Time, Slow Strong Mode, Cload = 50 pF
7
22
–
ns
Vdd = 3 to 5.25V, 10% - 90%
Figure 6. GPIO Timing Diagram
90%
GPIO
Pin
Output
Voltage
10%
TRiseF
TRiseS
TFallF
TFallS
AC Operational Amplifier Specifications
Table 21 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V at 25°C and are for design
guidance only.
Table 21. AC Operational Amplifier Specifications
Symbol
TCOMP
Description
Comparator Mode Response Time, 50 mV
Min
Typ
Max
100
Units
ns
Vdd ≥ 3.0V
Notes
AC Low Power Comparator Specifications
Table 22 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V at 25°C and are for design guidance
only.
Table 22. AC Low Power Comparator Specifications
Symbol
TRLPC
Description
LPC response time
Document Number: 001-43084 Rev. *L
Min
–
Typ
–
Max
50
Units
Notes
μs
≥ 50 mV overdrive comparator
reference set within VREFLPC
Page 21 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
AC Digital Block Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V, at 25°C and are
for design guidance only.
Table 23. AC Digital Block Specifications
Function
All functions
Timer
Counter
Dead Band
CRCPRS
(PRS Mode)
Description
Block Input Clock Frequency
Vdd ≥ 4.75V
Vdd < 4.75V
Input Clock Frequency
No Capture, Vdd ≥ 4.75V
No Capture, Vdd < 4.75V
With Capture
Capture Pulse Width
Input Clock Frequency
No Enable Input, Vdd ≥ 4.75V
No Enable Input, Vdd < 4.75V
With Enable Input
Enable Input Pulse Width
Kill Pulse Width
Asynchronous Restart Mode
Synchronous Restart Mode
Disable Mode
Input Clock Frequency
Vdd ≥ 4.75V
Vdd < 4.75V
Input Clock Frequency
Vdd ≥ 4.75V
Vdd < 4.75V
Input Clock Frequency
CRCPRS
(CRC Mode)
SPIM
Input Clock Frequency
SPIS
Transmitter
Receiver
Input Clock (SCLK) Frequency
Width of SS_Negated Between Transmissions
Input Clock Frequency
Vdd ≥ 4.75V, 2 Stop Bits
Vdd ≥ 4.75V, 1 Stop Bit
Vdd < 4.75V
Input Clock Frequency
Vdd ≥ 4.75V, 2 Stop Bits
Vdd ≥ 4.75V, 1 Stop Bit
Vdd < 4.75V
Min
Typ
Max
Units
Notes
–
–
–
–
50.4[16]
25.2[16]
MHz
MHz
–
–
–
50[15]
–
–
–
–
50.4[16]
25.2[16]
25.2[16]
–
MHz
MHz
MHz
ns
–
–
–
50[15]
–
–
–
–
50.4[16]
25.2[16]
25.2[16]
–
MHz
MHz
MHz
ns
20
50[15]
50[15]
–
–
–
–
–
–
ns
ns
ns
–
–
–
–
50.4[16]
25.2[16]
MHz
MHz
–
–
–
–
–
–
50.4[16]
25.2[16]
25.2[16]
MHz
MHz
MHz
–
–
8.4[16]
–
–
4.2[16]
50[15]
–
–
–
–
–
–
–
–
50.4[16]
25.2[16]
25.2[16]
MHz The SPI serial clock (SCLK)
frequency is equal to the input
clock frequency divided by 2.
MHz The input clock is the SPI SCLK
in SPIS mode.
ns
The baud rate is equal to the input
MHz clock frequency divided by 8.
–
–
–
–
–
–
50.4[16]
25.2[16]
25.2[16]
MHz
MHz
The baud rate is equal to the input
MHz clock frequency divided by 8.
MHz
MHz
Notes
15. 50 ns minimum input pulse width is based on the input synchronizers running at 24 MHz (42 ns nominal period).
16. Accuracy derived from IMO with appropriate trim for VDD range.
Document Number: 001-43084 Rev. *L
Page 22 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
AC External Clock Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V or 3.3V at 25°C and are
for design guidance only.
Table 24. 5V AC External Clock Specifications
Symbol
Description
Min
Typ
Max
Units
FOSCEXT
Frequency
0.093
–
24.6
MHz
–
High Period
20.6
–
5300
ns
–
Low Period
20.6
–
–
ns
–
Power Up IMO to Switch
150
–
–
μs
Notes
Table 25. 3.3V AC External Clock Specifications
Min
Typ
Max
Units
FOSCEXT
Symbol
Frequency with CPU Clock divide by 1
Description
0.093
–
12.3
MHz Maximum CPU frequency is
12 MHz at 3.3V. With the CPU
clock divider set to 1, the
external clock must adhere to
the maximum frequency and
duty cycle requirements.
FOSCEXT
Frequency with CPU Clock divide by 2 or greater
0.186
–
24.6
MHz If the frequency of the external
clock is greater than 12 MHz,
the CPU clock divider must be
set to 2 or greater. In this case,
the CPU clock divider ensures
that the fifty percent duty cycle
requirement is met.
–
High Period with CPU Clock divide by 1
41.7
–
5300
ns
–
Low Period with CPU Clock divide by 1
41.7
–
–
ns
–
Power Up IMO to Switch
150
–
–
μs
Notes
SAR10 ADC AC Specifications
Table 26 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V and 3.3V at 25°C and are for design
guidance only.
Table 26. SAR10 ADC AC Specifications
Symbol
Description
Min
Typ
Max
Units
Freq3
Input clock frequency 3V
–
–
2.7
MHz
Freq5
Input clock frequency 5V
–
–
2.7
MHz
Document Number: 001-43084 Rev. *L
Notes
Page 23 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
AC Programming Specifications
Table 27 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, or 3.3V at 25°C and are for design
guidance only.
Table 27. AC Programming Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
TRSCLK
Rise Time of SCLK
1
–
20
ns
TFSCLK
Fall Time of SCLK
1
–
20
ns
TSSCLK
Data Set up Time to Falling Edge of SCLK
40
–
–
ns
THSCLK
Data Hold Time from Falling Edge of SCLK
40
–
–
ns
FSCLK
Frequency of SCLK
0
–
8
MHz
FSCLK3
Frequency of SCLK3
0
–
6
MHz VDD < 3.6V
TERASEB
Flash Erase Time (Block)
–
10
–
ms
TWRITE
Flash Block Write Time
–
40
–
ms
TDSCLK
Data Out Delay from Falling Edge of SCLK
–
–
55
ns
3.6 < Vdd; at 30 pF Load
TDSCLK3
Data Out Delay from Falling Edge of SCLK
–
–
65
ns
3.0 ≤ Vdd ≤ 3.6; at 30 pF Load
TERASEALL
Flash Erase Time (Bulk)
–
40
–
ns
TPROGRAM_HOT
Flash Block Erase + Flash Block Write Time
–
–
100
ms
TPROGRAM_COLD Flash Block Erase + Flash Block Write Time
–
–
200
ms
Document Number: 001-43084 Rev. *L
Page 24 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
AC I2C Specifications
Table 28 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C
≤ TA ≤ 85°C, and 3.0V to 3.6V and -40°C ≤ TA ≤ 85°C, respectively. Typical parameters apply to 5V, 3.3V, or 2.7V at 25°C and are for
design guidance only.
Table 28. AC Characteristics of the I2C SDA and SCL Pins for Vdd ≥ 3.0V
Symbol
Standard Mode
Min
Max
0
100
Description
FSCLI2C
SCL Clock Frequency
THDSTAI2C
TLOWI2C
Hold Time (repeated) START Condition.
After this period, the first clock pulse is
generated.
LOW Period of the SCL Clock
THIGHI2C
TSUSTAI2C
THDDATI2C
Fast Mode
Min
Max
0
400
Units
kHz
4.0
–
0.6
–
μs
4.7
–
1.3
–
μs
HIGH Period of the SCL Clock
4.0
–
0.6
–
μs
Setup Time for a Repeated START
Condition
Data Hold Time
4.7
–
0.6
–
μs
0
–
0
–
μs
TSUDATI2C
Data Setup Time
250
–
100[10]
–
ns
TSUSTOI2C
Setup Time for STOP Condition
4.0
–
0.6
–
μs
TBUFI2C
Bus Free Time Between a STOP and
START Condition
Pulse Width of spikes are suppressed by
the Input Filter
4.7
–
1.3
–
μs
–
–
0
50
ns
TSPI2C
Notes
Figure 7. Definition for Timing for Fast/Standard Mode on the I2C Bus
I2C_SDA
TSUDATI2C
THDSTAI2C
TSPI2C
THDDATI2CTSUSTAI2C
TBUFI2C
I2C_SCL
THIGHI2C TLOWI2C
S
START Condition
TSUSTOI2C
Sr
Repeated START Condition
P
S
STOP Condition
Note
10. A Fast-Mode I2C-bus device may be used in a Standard-Mode I2C-bus system, but the requirement TSUDATI2C ≥ 250 ns must then be met. This is automatically the
case if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit
to the SDA line trmax + TSUDATI2C = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released.
Document Number: 001-43084 Rev. *L
Page 25 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Packaging Information
Figure 8. 28-Pin SOIC
NOTE :
PIN 1 ID
1. JEDEC STD REF MO-119
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH,BUT
14
DOES INCLUDE MOLD MISMATCH AND ARE MEASURED AT THE MOLD PARTING LINE.
1
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.010 in (0.254 mm) PER SIDE
MIN.
MAX.
3. DIMENSIONS IN INCHES
0.291[7.39]
4. PACKAGE WEIGHT 0.85gms
0.300[7.62]
0.394[10.01]
*
0.419[10.64]
15
28
PART #
S28.3 STANDARD PKG.
SZ28.3 LEAD FREE PKG.
0.026[0.66]
0.032[0.81]
SEATING PLANE
0.697[17.70]
0.713[18.11]
0.092[2.33]
0.105[2.67]
0.004[0.10]
0.050[1.27]
0.013[0.33]
0.004[0.10] *
0.019[0.48]
0.0118[0.30]
TYP.
0.0091[0.23]
0.0125[3.17]
0.015[0.38]
0.050[1.27]
51-85026 *E
Figure 9. 44-Pin TQFP
12.00±0.25 SQ
10.00±0.10 SQ
44
34
0° MIN.
33
1
0.37±0.05
R. 0.08 MIN.
0.20 MAX.
STAND-OFF
0.05 MIN.
0.15 MAX.
0.25
GAUGE PLANE
R. 0.08 MIN.
0.20 MIN.
0-7°
0.20 MIN.
11
1.00 REF.
0.80
B.S.C.
23
DETAIL
12
0.60±0.15
A
22
NOTE:
1. JEDEC STD REF MS-026
SEATING PLANE
1.60 MAX.
12°±1°
(8X)
1.40±0.05
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION /END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0.10
0.20 MAX.
SEE DETAIL
A
51-85064 *D
Document Number: 001-43084 Rev. *L
Page 26 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Thermal Impedances
Table 29. Thermal Impedances per Package
Typical θJA [11]
Package
28 SOIC
68°C/W
44 TQFP
61°C/W
Solder Reflow Peak Temperature
Following is the minimum solder reflow peak temperature to achieve good solderability.
Table 30. Thermal Impedances per Package
Package
Maximum Peak Temperature
Time at Maximum Peak Temperature
28 SOIC
260 °C
20 s
44 TQFP
260 °C
20 s
Ordering Information
The following table lists the key package features and ordering codes of this PSoC device family.
Ordering Code
Flash (Kbytes)
RAM (Bytes)
Temperature
Range
Digital Blocks
(Rows of 4)
Analog Blocks
(Columns of 3)
Digital I/O Pins
Analog Inputs
Analog Outputs
XRES Pin
Table 31. PSoC Device Family Key Features and Ordering Information
28 SOIC
CY8C21345-24SXI
8
512B
-40°C to +85°C
4
6
24
10
0
Y
28 SOIC (Tape and Reel)
CY8C21345-24SXIT
8
512B
-40°C to +85°C
4
6
24
10
0
Y
28 SOIC
CY8C22345-24SXI
16
1K
-40°C to +85°C
8
6
24
10
0
Y
28 SOIC (Tape and Reel)
CY8C22345-24SXIT
16
1K
-40°C to +85°C
8
6
24
10
0
Y
44 TQFP
CY8C22545-24AXI
16
1K
-40°C to +85°C
8
6
38
10
0
Y
44 TQFP (Tape and Reel)
CY8C22545-24AXIT
16
1K
-40°C to +85°C
8
6
38
10
0
Y
Package
Ordering Code Definitions
CY 8 C 2x xxx-SPxx
Package Type:
Thermal Rating:
PX = PDIP Pb-Free
C = Commercial
SX = SOIC Pb-Free
I = Industrial
PVX = SSOP Pb-Free E = Extended
LFX/LTX = QFN Pb-Free
AX = TQFP Pb-Free
CPU Speed: 24 MHz
Part Number
Family Code (21, 22)
Technology Code: C = CMOS
Marketing Code: 8 = PSoC
Company ID: CY = Cypress
Document Number: 001-43084 Rev. *L
Page 27 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Acronyms
Acronyms Used
Table 32 lists the acronyms that are used in this document.
Table 32. Acronyms Used in this Datasheet
Acronym
AC
Description
Acronym
Description
alternating current
MAC
multiply-accumulate
ADC
analog-to-digital converter
MCU
microcontroller unit
API
application programming interface
MIPS
million instructions per second
CMOS
complementary metal oxide semiconductor
PCB
printed circuit board
CPU
central processing unit
PGA
programmable gain amplifier
CRC
cyclic redundancy check
PLL
phase-locked loop
CSD
capsense sigma delta
POR
power on reset
CT
continuous time
PPOR
precision power on reset
DAC
digital-to-analog converter
PRS
pseudo-random sequence
DC
direct current
PSoC®
Programmable System-on-Chip
DNL
differential nonlinearity
PWM
pulse width modulator
ECO
external crystal oscillator
QFN
quad flat no leads
EEPROM
electrically erasable programmable read-only
memory
RTC
real time clock
FSK
frequency-shift keying
SAR
successive approximation
GPIO
general-purpose I/O
SC
switched capacitor
I/O
input/output
SLIMO
slow IMO
ICE
in-circuit emulator
SOIC
small-outline integrated circuit
IDE
integrated development environment
SPI™
serial peripheral interface
IDAC
current DAC
SRAM
static random access memory
ILO
internal low speed oscillator
SROM
supervisory read only memory
IMO
internal main oscillator
SSOP
shrink small-outline package
INL
integral nonlinearity
TQFP
thin quad flat pack
IrDA
infrared data association
UART
universal asynchronous reciever / transmitter
ISSP
in-system serial programming
USB
universal serial bus
LPC
low power comparator
WDT
watchdog timer
LSB
least-significant bit
XRES
external reset
LVD
low voltage detect
Reference Documents
CY8C22x45 and CY8C21345 PSoC® Programmable System-on-Chip™ Technical Reference Manual (TRM) (001-48461)
Design Aids – Reading and Writing PSoC® Flash – AN2015 (001-40459)
Adjusting PSoC® Trims for 3.3 V and 2.7 V Operation – AN2012 (001-17397)
Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 (001-14503)
Notes
11. TJ = TA + POWER x θJA
Document Number: 001-43084 Rev. *L
Page 28 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Document Conventions
Units of Measure
Table 33 lists the units of measures.
Table 33. Units of Measure
Symbol
Unit of Measure
Symbol
Unit of Measure
kB
1024 bytes
mV
millivolts
°C
degree Celsius
nA
nanoampere
kilohertz
ns
nanosecond
kHz
kΩ
LSB
MHz
kilohm
W
ohm
least significant bit
%
percent
megahertz
pF
picofarad
microampere
ps
picosecond
µs
microsecond
sps
samples per second
µV
microvolts
pA
pikoampere
V
volts
µA
mA
milliampere
mm
millimeter
µW
microwatts
ms
millisecond
W
watt
Numeric Conventions
Hexadecimal numbers are represented with all letters in uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or ‘3Ah’).
Hexadecimal numbers may also be represented by a ‘0x’ prefix, the C coding convention. Binary numbers have an appended
lowercase ‘b’ (for example, 01010100b’ or ‘01000011b’). Numbers not indicated by an ‘h’ or ‘b’ are decimals.
Glossary
active high
5. A logic signal having its asserted state as the logic 1 state.
6. A logic signal having the logic 1 state as the higher voltage of the two states.
analog blocks
The basic programmable opamp circuits. These are SC (switched capacitor) and CT (continuous
time) blocks. These blocks can be interconnected to provide ADCs, DACs, multi-pole filters, gain
stages, and much more.
analog-to-digital
(ADC)
A device that changes an analog signal to a digital signal of corresponding magnitude. Typically,
an ADC converts a voltage to a digital number. The digital-to-analog (DAC) converter performs
the reverse operation.
API (Application
Programming
Interface)
A series of software routines that comprise an interface between a computer application and
lower level services and functions (for example, user modules and libraries). APIs serve as
building blocks for programmers that create software applications.
asynchronous
A signal whose data is acknowledged or acted upon immediately, irrespective of any clock signal.
bandgap
reference
A stable voltage reference design that matches the positive temperature coefficient of VT with
the negative temperature coefficient of VBE, to produce a zero temperature coefficient (ideally)
reference.
bandwidth
1. The frequency range of a message or information processing system measured in hertz.
2. The width of the spectral region over which an amplifier (or absorber) has substantial gain (or
loss); it is sometimes represented more specifically as, for example, full width at half maximum.
Document Number: 001-43084 Rev. *L
Page 29 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Glossary
(continued)
bias
1. A systematic deviation of a value from a reference value.
2. The amount by which the average of a set of values departs from a reference value.
3. The electrical, mechanical, magnetic, or other force (field) applied to a device to establish a
reference level to operate the device.
block
1. A functional unit that performs a single function, such as an oscillator.
2. A functional unit that may be configured to perform one of several functions, such as a digital
PSoC block or an analog PSoC block.
buffer
1. A storage area for data that is used to compensate for a speed difference, when transferring
data from one device to another. Usually refers to an area reserved for IO operations, into
which data is read, or from which data is written.
2. A portion of memory set aside to store data, often before it is sent to an external device or as
it is received from an external device.
3. An amplifier used to lower the output impedance of a system.
bus
1. A named connection of nets. Bundling nets together in a bus makes it easier to route nets
with similar routing patterns.
2. A set of signals performing a common function and carrying similar data. Typically represented
using vector notation; for example, address[7:0].
3. One or more conductors that serve as a common connection for a group of related devices.
clock
The device that generates a periodic signal with a fixed frequency and duty cycle. A clock is
sometimes used to synchronize different logic blocks.
comparator
An electronic circuit that produces an output voltage or current whenever two input levels simultaneously
satisfy predetermined amplitude requirements.
compiler
A program that translates a high level language, such as C, into machine language.
configuration
space
In PSoC devices, the register space accessed when the XIO bit, in the CPU_F register, is set to
‘1’.
crystal oscillator
An oscillator in which the frequency is controlled by a piezoelectric crystal. Typically a piezoelectric
crystal is less sensitive to ambient temperature than other circuit components.
cyclic redundancy A calculation used to detect errors in data communications, typically performed using a linear
check (CRC)
feedback shift register. Similar calculations may be used for a variety of other purposes such as
data compression.
data bus
A bi-directional set of signals used by a computer to convey information from a memory location
to the central processing unit and vice versa. More generally, a set of signals used to convey
data between digital functions.
debugger
A hardware and software system that allows the user to analyze the operation of the system
under development. A debugger usually allows the developer to step through the firmware one
step at a time, set break points, and analyze memory.
dead band
A period of time when neither of two or more signals are in their active state or in transition.
digital blocks
The 8-bit logic blocks that can act as a counter, timer, serial receiver, serial transmitter, CRC
generator, pseudo-random number generator, or SPI.
Document Number: 001-43084 Rev. *L
Page 30 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Glossary
(continued)
digital-to-analog
(DAC)
A device that changes a digital signal to an analog signal of corresponding magnitude. The analogto-digital (ADC) converter performs the reverse operation.
duty cycle
The relationship of a clock period high time to its low time, expressed as a percent.
emulator
Duplicates (provides an emulation of) the functions of one system with a different system, so that
the second system appears to behave like the first system.
external reset
(XRES)
An active high signal that is driven into the PSoC device. It causes all operation of the CPU and
blocks to stop and return to a pre-defined state.
flash
An electrically programmable and erasable, non-volatile technology that provides users with the
programmability and data storage of EPROMs, plus in-system erasability. Non-volatile means
that the data is retained when power is off.
Flash block
The smallest amount of Flash ROM space that may be programmed at one time and the smallest
amount of Flash space that may be protected. A Flash block holds 64 bytes.
frequency
The number of cycles or events per unit of time, for a periodic function.
gain
The ratio of output current, voltage, or power to input current, voltage, or power, respectively.
Gain is usually expressed in dB.
I2C
A two-wire serial computer bus by Philips Semiconductors (now NXP Semiconductors). I2C is an
Inter-Integrated Circuit. It is used to connect low-speed peripherals in an embedded system. The
original system was created in the early 1980s as a battery control interface, but it was later used
as a simple internal bus system for building control electronics. I2C uses only two bi-directional
pins, clock and data, both running at +5V and pulled high with resistors. The bus operates at 100
kbits/second in standard mode and 400 kbits/second in fast mode.
ICE
The in-circuit emulator that allows users to test the project in a hardware environment, while
viewing the debugging device activity in a software environment (PSoC Designer).
input/output (I/O) A device that introduces data into or extracts data from a system.
interrupt
A suspension of a process, such as the execution of a computer program, caused by an event
external to that process, and performed in such a way that the process can be resumed.
interrupt service
routine (ISR)
A block of code that normal code execution is diverted to when the M8C receives a hardware
interrupt. Many interrupt sources may each exist with its own priority and individual ISR code
block. Each ISR code block ends with the RETI instruction, returning the device to the point in
the program where it left normal program execution.
jitter
1. A misplacement of the timing of a transition from its ideal position. A typical form of corruption that occurs on
serial data streams.
2. The abrupt and unwanted variations of one or more signal characteristics, such as the interval between
successive pulses, the amplitude of successive cycles, or the frequency or phase of successive cycles.
low-voltage detect A circuit that senses Vdd and provides an interrupt to the system when Vdd falls below a
(LVD)
selected threshold.
M8C
An 8-bit Harvard-architecture microprocessor. The microprocessor coordinates all activity inside
a PSoC by interfacing to the Flash, SRAM, and register space.
Document Number: 001-43084 Rev. *L
Page 31 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Glossary
(continued)
master device
A device that controls the timing for data exchanges between two devices. Or when devices are
cascaded in width, the master device is the one that controls the timing for data exchanges
between the cascaded devices and an external interface. The controlled device is called the
slave device.
microcontroller
An integrated circuit chip that is designed primarily for control systems and products. In addition
to a CPU, a microcontroller typically includes memory, timing circuits, and IO circuitry. The reason
for this is to permit the realization of a controller with a minimal quantity of chips, thus
achieving maximal possible miniaturization. This in turn, reduces the volume and the cost of
the controller. The microcontroller is normally not used for general-purpose computation as is a
microprocessor.
mixed-signal
The reference to a circuit containing both analog and digital techniques and components.
modulator
A device that imposes a signal on a carrier.
noise
1. A disturbance that affects a signal and that may distort the information carried by the signal.
2. The random variations of one or more characteristics of any entity such as voltage, current, or data.
oscillator
A circuit that may be crystal controlled and is used to generate a clock frequency.
parity
A technique for testing transmitting data. Typically, a binary digit is added to the data to make the
sum of all the digits of the binary data either always even (even parity) or always odd (odd parity).
phase-locked
loop (PLL)
An electronic circuit that controls an oscillator so that it maintains a constant phase angle relative
to a reference signal.
pinouts
The pin number assignment: the relation between the logical inputs and outputs of the PSoC
device and their physical counterparts in the printed circuit board (PCB) package. Pinouts
involve pin numbers as a link between schematic and PCB design (both being computer generated
files) and may also involve pin names.
port
A group of pins, usually eight.
power on reset
(POR)
A circuit that forces the PSoC device to reset when the voltage is below a pre-set level. This is
one type of hardware reset.
PSoC®
Cypress Semiconductor’s PSoC® is a registered trademark and Programmable System-onChip™ is a trademark of Cypress.
PSoC Designer™ The software for Cypress’ Programmable System-on-Chip technology.
pulse width
An output in the form of duty cycle which varies as a function of the applied measurand
modulator (PWM)
RAM
An acronym for random access memory. A data-storage device from which data can be read out
and new data can be written in.
register
A storage device with a specific capacity, such as a bit or byte.
reset
A means of bringing a system back to a know state. See hardware reset and software reset.
ROM
An acronym for read only memory. A data-storage device from which data can be read out, but
new data cannot be written in.
Document Number: 001-43084 Rev. *L
Page 32 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Glossary
(continued)
serial
1. Pertaining to a process in which all events occur one after the other.
2. Pertaining to the sequential or consecutive occurrence of two or more related activities in a single device or
channel.
settling time
The time it takes for an output signal or value to stabilize after the input has changed from one
value to another.
shift register
A memory storage device that sequentially shifts a word either left or right to output a stream of
serial data.
slave device
A device that allows another device to control the timing for data exchanges between two
devices. Or when devices are cascaded in width, the slave device is the one that allows another
device to control the timing of data exchanges between the cascaded devices and an external
interface. The controlling device is called the master device.
SRAM
An acronym for static random access memory. A memory device allowing users to store and
retrieve data at a high rate of speed. The term static is used because, after a value has been
loaded into an SRAM cell, it remains unchanged until it is explicitly altered or until power is
removed from the device.
SROM
An acronym for supervisory read only memory. The SROM holds code that is used to boot the
device, calibrate circuitry, and perform Flash operations. The functions of the SROM may be
accessed in normal user code, operating from Flash.
stop bit
A signal following a character or block that prepares the receiving device to receive the next
character or block.
synchronous
1. A signal whose data is not acknowledged or acted upon until the next active edge of a clock signal.
2. A system whose operation is synchronized by a clock signal.
tri-state
A function whose output can adopt three states: 0, 1, and Z (high-impedance). The function does
not drive any value in the Z state and, in many respects, may be considered to be disconnected
from the rest of the circuit, allowing another output to drive the same net.
UART
A UART or universal asynchronous receiver-transmitter translates between parallel bits of data
and serial bits.
user modules
Pre-build, pre-tested hardware/firmware peripheral functions that take care of managing and
configuring the lower level Analog and Digital PSoC Blocks. User Modules also provide high
level API (Application Programming Interface) for the peripheral function.
user space
The bank 0 space of the register map. The registers in this bank are more likely to be modified
during normal program execution and not just during initialization. Registers in bank 1 are most
likely to be modified only during the initialization phase of the program.
VDD
A name for a power net meaning "voltage drain." The most positive power supply signal. Usually
5 V or 3.3 V.
VSS
A name for a power net meaning "voltage source." The most negative power supply signal.
watchdog timer
A timer that must be serviced periodically. If it is not serviced, the CPU resets after a specified
period of time.
Document Number: 001-43084 Rev. *L
Page 33 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Document History Page
Document Title: CY8C21345, CY8C22345, CY8C22545 PSoC® Programmable System-on-Chip
Document Number: 001-43084
Revision
ECN
Orig. of
Change
Submission
Date
**
2251907
PMP/AESA
See ECN
New Data sheet
*A
2506377
EIJ/AESA
See ECN
Changed data sheet status to “Preliminary”. Changed part numbers to
CY8C22x45. Updated data sheet template.
Added 56-Pin OCD information. Added: “You must put filters on intended ADC
input channels for anti-aliasing. This ensures that any out-of-band content is not
folded into the Input Signal Band." To Section Analog System on page 4.
Corrected Minimum Electro Static Discharge Voltage in Table 7 on page 15.
*B
2558750
PMP/AESA
08/28/2008
Updated Features on page 1, PSoC Core on page 3, Analog System on page 4.
Changed DBB to DBC, and DCB to DCC in Register Tables Table 5 on page 12
and Table 6 on page 13.
Removed INL at 8 bit reference in Table 14 on page 18.
Changed IDD3 value Table 16 on page 18 Typ:3.3 mA, Max 6 mA
Added “3.0V < Vdd < 3.6V and -40C < TA < 85C, IMO can guarantee 5% accuracy
only” to Table 19 on page 20.
Updated data sheet template.
*C
2606793
NUQ/AESA
11/19/2008
Updated data sheet status to “Final”. Updated block diagram on page 1.
Removed CY8C22045 56-Pin OCD information. Added part numbers
CY8C21345, CY8C22345, and CY8C22545. For more details, see CDT 31271.
*D
2615697
PMP/AESA
12/03/2008
Confirmed CY8C22345 and CY8C21345 have same pinout on page 8.
Confirmed that IMO has 5% accuracy in Table 19 on page 20.
*E
2631733
PMP/PYRS
01/07/2009
Updated Table 16. SAR10 ADC DC Specifications and Table 29 AC
Programming Specifications. Title changed to “CY8C21345, CY8C22345,
CY8C22545 PSoC® Programmable System-on-Chip™”
*F
2648800
JHU/AESA
01/28/2009
Updated INL, DNL information in Table 14 on page 18, Development Tools on
page 6, and TDSCLK parameter in Table 27 on page 24.
*G
2658078
HMI/AESA
02/11/2009
Updated section Features on page 1.
*H
2667311
JHU/AESA
03/16/2009
Added parameter “F32KU” and added Min% and Max % to parameter “FIMO6” in
Table 19 on page 20, according to updated SLIMO spec.
*I
2748976 JZHU/PYRS
08/06/2009
Updated F32K1 max rating in Table 19 on page 20.
*J
2786560
JZHU
10/23/2009
Added DCILO, TERASEALL, TPROGRAM_HOT, TPROGRAM_COLD, SRPOWERUP, IOH,
and IOL parameters.
Added Tape and Reel parts in Ordering Information table
*K
2901653
NJF
03/30/2010
Updated PSoC Designer Software Subsystems.
Added TBAKETEMP and TBAKETIME parameters in Absolute Maximum Ratings
Modified Note 6 on page 17.
Added FOUT48M parameter in 5V and 3.3V AC Chip-Level Specifications.
Removed AC Analog Mux Bus Specifications.
Updated Ordering Code Definitions.
Updated links in Sales, Solutions, and Legal Information.
*L
3114978
NJF
12/19/10
Document Number: 001-43084 Rev. *L
Description of Change
Added DC I2C Specifications.
Added Tjit_IMO specification, removed existing jitter specifications.
Updated DC Programming Specifications.
Updated AC Digital Block Specifications.
Updated I2C Timing Diagram.
Added Solder Reflow Peak Temperature table.
Updated Units of Measure, Acronyms, Glossary, and References sections.
Page 34 of 35
[+] Feedback
CY8C21345
CY8C22345, CY8C22545
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
cypress.com/go/memory
cypress.com/go/image
PSoC
Touch Sensing
cypress.com/go/psoc
cypress.com/go/touch
USB Controllers
Wireless/RF
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2008-2010. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used
for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use
as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support
systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-43084 Rev. *L
Revised December 17, 2010
Page 35 of 35
PSoC Designer™ and Programmable System-on-Chip™ are trademarks and PSoC® and CapSense® are registered trademarks of Cypress Semiconductor Corporation.
Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided
that the system conforms to the I2C Standard Specification as defined by Philips. As from October 1st, 2006 Philips Semiconductors has a new trade name - NXP Semiconductors.
All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback