PD -20602 rev. B 01/2000 HFA06TB120S.. Series TM HEXFRED Ultrafast, Soft Recovery Diode Features BASE + 2 (N/C) Benefits VR = 1200V VF(typ.)* = 2.4V (K) • Ultrafast Recovery • Ultrasoft Recovery • Very Low IRRM • Very Low Qrr • Guaranteed Avalanche • Specified at Operating Conditions 1 IF(AV) = 6.0A Qrr (typ.)= 116nC 3 _ IRRM(typ.) = 4.4A trr(typ.) = 26ns (A) di(rec)M/dt (typ.)* = 100A/µs • Reduced RFI and EMI • Reduced Power Loss in Diode and Switching Transistor • Higher Frequency Operation • Reduced Snubbing • Reduced Parts Count Description D2 Pak International Rectifier's HFA06TB120S is a state of the art ultra fast recovery diode. Employing the latest in epitaxial construction and advanced processing techniques it features a superb combination of characteristics which result in performance which is unsurpassed by any rectifier previously available. With basic ratings of 1200 volts and 6 amps continuous current, the HFA06TB120S is especially well suited for use as the companion diode for IGBTs and MOSFETs. In addition to ultra fast recovery time, the HEXFRED product line features extremely low values of peak recovery current (IRRM) and does not exhibit any tendency to "snap-off" during the t b portion of recovery. The HEXFRED features combine to offer designers a rectifier with lower noise and significantly lower switching losses in both the diode and the switching transistor. These HEXFRED advantages can help to significantly reduce snubbing, component count and heatsink sizes. The HEXFRED HFA06TB120S is ideally suited for applications in power supplies and power conversion systems (such as inverters), motor drives, and many other similar applications where high speed, high efficiency is needed. Absolute Maximum Ratings VR IF @ TC = 100°C IFSM IFRM PD @ TC = 25°C PD @ TC = 100°C TJ TSTG Parameter Cathode-to-Anode Voltage Continuous Forward Current Single Pulse Forward Current Maximum Repetitive Forward Current Maximum Power Dissipation Maximum Power Dissipation Operating Junction and Storage Temperature Range Max. 1200 8.0 80 24 62.5 25 -55 to +150 Units V A W °C * 125°C 1 HFA06TB120S..Series PD-20602 rev. B 01/2000 Electrical Characteristics @ TJ = 25°C (unless otherwise specified) Parameter VBR Cathode Anode Breakdown Min. Typ. Max. Units 1200 ––– ––– ––– 2.7 3.0 ––– 3.5 3.9 ––– 2.4 2.8 ––– 0.26 5.0 V Test Conditions IR = 100µA Voltage VFM Max. Forward Voltage IF = 6.0A V IF = 12A IF = 6.0A, TJ = 125°C IRM Max. Reverse Leakage Current ––– 110 500 CT Junction Capacitance ––– 9.0 14 pF VR = 200V LS Series Inductance ––– 8.0 ––– nH Measured lead to lead 5mm from pkg body µA VR = VR Rated TJ = 125°C, VR = 0.8 x VR RatedD R Rated Dynamic Recovery Characteristics @ TJ = 25°C (unless otherwise specified) Parameter trr Reverse Recovery Time trr1 trr2 IRRM1 Peak Recovery Current IRRM2 Qrr1 Reverse Recovery Charge Min. Typ. Max. Units Test Conditions ––– 26 ––– IF = 1.0A, dif/dt = 200A/µs, VR = 30V ––– 53 80 ––– 87 130 TJ = 125°C ––– 4.4 8.0 TJ = 25°C ––– 5.0 9.0 ––– 116 320 ns A TJ = 25°C IF = 6.0A TJ = 125°C nC TJ = 25°C Qrr2 ––– 233 585 TJ = 125°C di(rec)M /dt1 Peak Rate of Recovery ––– 180 ––– TJ = 25°C di(rec)M /dt2 Current During t b ––– 100 ––– A/µs VR = 200V dif/dt = 200A/µs TJ = 125°C Thermal - Mechanical Characteristics Parameter Min. Typ. Max. Units Tlead Q Lead Temperature –––– –––– 300 °C RthJC Thermal Resistance, Junction to Case –––– –––– 2.0 RthJA R Thermal Resistance, Junction to Ambient –––– –––– 80 RthCSS Thermal Resistance, Case to Heat Sink –––– 0.5 –––– Wt Weight –––– 2.0 –––– g –––– 0.07 –––– (oz) Q 0.063 in. from Case (1.6mm) for 10 sec R Typical Socket Mount 2 K/W HFA06TB120S ..Series PD-20602 rev. B 01/2000 100 1000 Reverse Current - IR (µA) TJ = 150˚C 125˚C 100˚C 10 1 25˚C 0.1 0.01 0 200 400 600 800 1000 1200 1400 Reverse Voltage - VR (V) 100 1 Junction Capacitance - CT (pF) Instantaneous Forward Current - IF (A) 10 100 T = 150˚C J T = 125˚C J T = 25˚C J 0.1 T = 25˚C J 10 1 0 2 4 Forward Voltage Drop - VFM (V) 6 1 10 100 1000 10000 Reverse Voltage - VR (V) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage Fig. 1 - Typical Forward Voltage Drop Characteristics Thermal Impedance ZthJC (°C/W) 10 1 D = 0.50 D = 0.20 D = 0.10 D = 0.05 D = 0.02 D = 0.01 PDM t1 t2 0.1 Single Pulse (Thermal Resistance) Notes: 1. Duty factor D = 1t / t2 2. Peak TJ = PDM x ZthJC + TC 0.01 0.00001 0.0001 0.001 0.01 0.1 1 10 100 Fig. 4 - Maximum Thermal Impedance ZthJC Characteristics 3 HFA06TB120S..Series PD-20602 rev. B 01/2000 25 110 IF = 6 A IF = 4 A 100 VR = 200V TJ = 125˚C TJ = 25˚C 20 90 IF = 6 A IF = 4 A 15 70 Irr - ( A) trr - ( nC ) 80 60 10 50 40 5 VR = 200V TJ = 125˚C TJ = 25˚C 30 20 100 0 100 1000 1000 dif /dt - (A/µs ) dif /dt - (A/µs ) Fig. 5 - Typical Reverse Recovery Vs. dif /dt Fig. 6 - Typical Recovery Current Vs. dif /dt 10000 1000 VR = 200V TJ = 125˚C TJ = 25˚C 800 di(REC) M/dt - (A/µs ) Qrr - ( nC ) IF = 6 A IF = 4 A 600 400 IF = 6 A IF = 4 A 1000 100 VR = 200V TJ = 125˚C TJ = 25˚C 200 0 100 1000 dif /dt - (A/µs ) Fig. 8 - Typical Stored Charge vs. dif /dt 4 10 100 1000 dif /dt - (A/µs ) Fig. 7 - Typical di(REC) M/dt vs. dif /dt HFA06TB120S ..Series PD-20602 rev. B 01/2000 R E V E R S E R E C O V E R Y C IR C U IT V R = 200V 0 .0 1 Ω L = 70µ H D .U .T . d if/d t A D JU S T D IR F P 2 5 0 G S Fig. 9- Reverse Recovery Parameter Test Circuit 3 t rr IF tb ta 0 Q rr 2 I RR M 4 0 .5 I R R M d i(re c )M /d t 5 0 .7 5 I R R M 1 1. dif/dt - Rate of change of current through zero crossing 2. IRRM - Peak reverse recovery current d i f /d t 4. Qrr - Area under curve defined by trr and I RRM t rr X IRRM 3. trr - Reverse recovery Qrr = time measured from zero 2 crossing point of negative going IF to point where a line 5. di(rec)M /dt - Peak rate of passing through 0.75 IRRM change of current during tb and 0.50 IRRM portion of t rr extrapolated to zero current Fig. 10 - Reverse Recovery Waveform and Definitions 5 HFA06TB120S..Series PD-20602 rev. B 01/2000 Outline Table 4 . 6 9 (0 . 1 8 ) 4 .2 0 ( 0 .1 6 ) 1 0 . 16 (0 . 4 0 ) RE F . 1.32 ( 0.05) 1 .2 2 (0 .0 5) 6.47 ( 0.25) 1 5 . 4 9 (0 . 6 1 ) 93° 6 .1 8 ( 0 .2 4 ) 1 4 . 7 3 (0 . 5 8 ) 5 .2 8 (0 .2 1 ) 2 .6 1 (0 .1 0 ) 4 .7 8 (0 .1 9 ) 2 .3 2 (0 .0 9 ) 0.55 ( 0.02) 0.46 ( 0.02) 8 .8 9 (0 .3 5) 3X R EF. 1 .4 0 (0 .0 55 ) 1 .1 4 (0 .0 45 ) 2X 1 0.93 ( 0.37) M IN IM U M R EC OM M EN D E D F OO TP R IN T 0 .6 9 ( 0 . 2 7 ) 1 1 . 4 3 (0 . 4 5 ) 3 4 . 5 7 (0 . 1 8 ) 8 . 8 9 (0 . 3 5 ) 4.32 ( 0.17) 1 7 . 7 8 (0 .7 0 ) 2 0 . 6 1 (0 . 0 2 ) M AX . 5 . 0 8 (0 . 2 0 ) R EF . 3 .8 1 (0 .1 5 ) 2 .0 8 ( 0 . 0 8 ) 2X 2.54 ( 0.10) 2X 2 Conforms to JEDEC Outline D PAK Dimensions in millimeters and inches Part Marking Information EXAMPLE: THIS IS AN HFA06TB120S PART NUMBER (K) INTERNATIONAL RECTIFIER LOGO HFA06TB120S 5K3A 9712 ASSEMBLY LOT CODE (N/C) 6 (A) DATE CODE (YYWW) YY = YEAR WW = WEEK HFA06TB120S ..Series PD-20602 rev. B 01/2000 Tape & Reel Information T RR 1. 6 0 ( 0. 06 3 ) 1. 5 0 ( 0. 05 9 ) 4. 1 0 ( 0. 16 1 ) 3. 9 0 ( 0. 15 3 ) 1. 6 0 ( 0. 06 3 ) D IA. 1. 5 0 ( 0. 05 9 ) 0. 3 68 (0 .0 1 4 5 ) 0. 3 42 (0 .0 1 3 5 ) FE ED D IR EC T ION 1. 8 5 (0 .07 3) 1. 6 5 (0 .06 5) 11 .6 0 (0 .4 5 7 ) 11 .4 0 (0 .4 4 9 ) 2 4 .3 0 (0 .95 7) 2 3 .9 0 (0 .94 1) 1 5 .4 2 (0 .6 0 9) 1 5 .2 2 (0 .6 0 1) TR L 1. 7 5 (0 .06 9) D IA . 1. 2 5 (0 .04 9) 1 0 .9 0 (0 .4 2 9) 1 0 .7 0 (0 .4 2 1) 4. 7 2 (0 .18 6 ) 4. 5 2 (0 .17 8 ) 16 .10 (0.6 34 ) 15 .90 (0.6 26 ) FE ED D IR E C TION 1 3 .5 0 (0 .5 3 2) 2 6 .4 0 (1 .0 3 9 ) 2 4 .4 0 (0 .9 6 1 ) 1 2 .8 0 (0 .5 0 4) D I A . SM D -2 20 Ta pe & R ee l W h e n o rd er ing , ind ic at e th e p a rt n u m b er, pa rt o rie nt at io n, a nd t he q u an t ity. Qu an titie s a re in m ult ip les o f 8 00 p iec e s p e r ree l fo r b o th T R L a nd T R R . 6 0 (2 .3 6 2) D IA . M IN . 36 0 (1 4 .17 3 ) D IA . M A X. Ordering Information Table Device Code 1 - Hexfred Family 2 - Process Designator HF A 06 1 2 3 TB 120 4 5 S TR 6 7 A = A subs. elec. irrad. B = B subs. Platinum 3 - Average Current: Code 06 = 6 AMPS 4 - Package Outline: Code TB = TO-220 2 Lead 5 - Voltage code : Code 120 = 1200 V 6 - Configuration : Code S = SMD 7 - Suffix : Code TR = Tape and Reel 7 HFA06TB120S..Series PD-20602 rev. B 01/2000 WORLD HEADQUARTERS: EUROPEAN HEADQUARTERS: IR CANADA: IR GERMANY: IR ITALY: IR FAR EAST: IR SOUTHEAST ASIA: IR TAIWAN: 8 233 Kansas St., El Segundo, California 90245 U.S.A. Tel: (310) 322 3331. Fax: (310) 322 3332. Hurst Green, Oxted, Surrey RH8 9BB, U.K. Tel: ++ 44 1883 732020. Fax: ++ 44 1883 733408. 15 Lincoln Court, Brampton, Markham, Ontario L6T3Z2. Tel: (905) 453 2200. Fax: (905) 475 8801. Saalburgstrasse 157, 61350 Bad Homburg. Tel: ++ 49 6172 96590. Fax: ++ 49 6172 965933. Via Liguria 49, 10071 Borgaro, Torino. Tel: ++ 39 11 4510111. Fax: ++ 39 11 4510220. K&H Bldg., 2F, 30-4 Nishi-Ikebukuro 3-Chome, Toshima-Ku, Tokyo, Japan 171. Tel: 81 3 3983 0086. 1 Kim Seng Promenade, Great World City West Tower,13-11, Singapore 237994. Tel: ++ 65 838 4630. 16 Fl. Suite D.207, Sec. 2, Tun Haw South Road, Taipei, 10673, Taiwan. Tel: 886 2 2377 9936.