NCV6334B 3MHz, 2A Synchronous Buck Converter High Efficiency, Low Ripple, Adjustable Output Voltage The NCV6334B, a family of synchronous buck converters, which is optimized to supply different sub systems of portable applications powered by one cell Li−ion or three cell Alkaline/NiCd/NiMH batteries. The devices are able to deliver up to 2 A on an external adjustable voltage. Operation with 3 MHz switching frequency allows employing small size inductor and capacitors. Input supply voltage feedforward control is employed to deal with wide input voltage range. Synchronous rectification and automatic PWM/PFM power save mode offer improved system efficiency. The NCV6334B is in a space saving, low profile 2.0 x 2.0 x 0.75 mm WDFN−8 package. Features • • • • • • • • • • • • • • • November, 2012 − Rev. 3 1 1 WDFN8 CASE 511BT AM MG G AM = Specific Device Code M = Date Code G = Pb−Free Package PINOUT PGND 1 SW 2 8 PVIN 7 AVIN 9 AGND 3 6 PG FB 4 5 EN (Top View) ORDERING INFORMATION See detailed ordering, marking and shipping information in the package dimensions section on page 2 of this data sheet. Cellular Phones, Smart Phones, and PDAs Portable Media Players Digital Still Cameras Wireless and DSL Modems USB Powered Devices Point of Load Game and Entertainment System © Semiconductor Components Industries, LLC, 2012 MARKING DIAGRAM (*Note: Microdot may be in either location) 2.3 V to 5.5 V Input Voltage Range External Adjustable Voltage Up to 2 A Output Current 3 MHz Switching Frequency Synchronous Rectification Automatic Power Save Enable Input Power Good Output Option Soft Start Over Current Protection Active Discharge When Disabled Thermal Shutdown Protection WDFN−8, 2 x 2 mm, 0.5 mm Pitch Package Maximum 0.8 mm Height for Super Thin Applications This is a Pb−Free Device Typical Applications • • • • • • • http://onsemi.com 1 Publication Order Number: NCV6334B/D NCV6334B NCV6334B 1uH Vo = 0.6V to Vin Cout 10uF R1 Cfb PGND PVIN SW AVIN AGND PG FB EN Vin = 2.3V to 5.5V Cin 10uF Rpg 1M Power Good Enable R2 Power Good Output Figure 1. Typical Application Circuits PIN DESCRIPTION Pin Name Type Description 1 PGND Power Ground Power Ground for power, analog blocks. Must be connected to the system ground. 2 SW Power Output Switch Power pin connects power transistors to one end of the inductor. 3 AGND Analog Ground Analog Ground analog and digital blocks. Must be connected to the system ground. 4 FB Analog Input Feedback Voltage from the buck converter output. This is the input to the error amplifier. This pin is connected to the resistor divider network between the output and AGND. 5 EN Digital Input Enable of the IC. High level at this pin enables the device. Low level at this pin disables the device. 6 PG Digital Output PG pin is for NCV6334B with Power Good option. It is open drain output. Low level at this pin indicates the device is not in power good, while high impedance at this pin indicates the device is in power good. 7 AVIN Analog Input Analog Supply. This pin is the analog and the digital supply of the device. An optional 1 mF or larger ceramic capacitor bypasses this input to the ground. This capacitor should be placed as close as possible to this input. 8 PVIN Power Input Power Supply Input. This pin is the power supply of the device. A 10 mF or larger ceramic capacitor must bypass this input to the ground. This capacitor should be placed as close a possible to this input. 9 PAD Exposed Pad Exposed Pad. Must be soldered to system ground to achieve power dissipation performances. This pin is internally unconnected ORDERING INFORMATION Device NCV6334BMTAATBG Marking Package Shipping† AM WDFN8 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 2 NCV6334B Vin Cin PVIN 8 L SW 2 Vo 1uH Cout 10uF 10uF AVIN 7 PWM / PFM Control UVLO PGND 1 Cfb R1 Enable Power Good EN 5 Rpg 1M MODE/PG 6 MODE PG Logic Control & Current Limit & Thermal Shutdown FB 4 Error Amp R2 AGND 3 Reference Voltage Figure 2. Functional Block Diagram MAXIMUM RATINGS Value Rating Input Supply Voltage to GND Switch Node to GND EN, PG to GND FB to GND Symbol Min Max Unit VPVIN, VAVIN −0.3 7.0 V VSW −0.3 7.0 V VEN, VPG −0.3 7.0 V VFB −0.3 2.5 V Human Body Model (HBM) ESD Rating (Note 1) ESD HBM 2000 V Machine Model (MM) ESD Rating (Note 1) ESD MM 200 V Latchup Current (Note 2) ILU −100 100 mA Operating Junction Temperature Range (Note 3) TJ −40 125 °C Operating Ambient Temperature Range TA −40 85 °C Storage Temperature Range TSTG −55 150 °C Thermal Resistance Junction−to−Top Case (Note 4) RqJC 12 °C/W Thermal Resistance Junction−to−Board (Note 4) RqJB 30 °C/W Thermal Resistance Junction−to−Ambient (Note 4) RqJA 62 °C/W PD 1.6 W MSL 1 − Power Dissipation (Note 5) Moisture Sensitivity Level (Note 6) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. This device series contains ESD protection and passes the following tests: Human Body Model (HBM) ±2.0 kV per JEDEC standard: JESD22−A114. Machine Model (MM) ±200 V per JEDEC standard: JESD22−A115. 2. Latchup Current per JEDEC standard: JESD78 Class II. 3. The thermal shutdown set to 160°C (typical) avoids potential irreversible damage on the device due to power dissipation. 4. The thermal resistance values are dependent of the PCB heat dissipation. Board used to drive these data was an 80 x 50 mm NCP6334EVB board. It is a multilayer board with 1 once internal power and ground planes and 2−once copper traces on top and bottom of the board. If the copper trances of top and bottom are 1 once too, RqJC = 11°C/W, RqJB = 30°C/W, and RqJA = 72°C/W. 5. The maximum power dissipation (PD) is dependent on input voltage, maximum output current and external components selected. 6. Moisture Sensitivity Level (MSL): 1 per IPC/JEDEC standard: J−STD−020A. http://onsemi.com 3 NCV6334B ELECTRICAL CHARACTERISTICS (VIN = 3.6 V, VOUT = 1.8 V, L = 1 mH, C = 10 mF, typical values are referenced to TJ = 25°C, Min and Max values are referenced to TJ up to 125°C, unless other noted.) Symbol Characteristics Test Conditions Min Typ Max Unit (Note 10) 2.3 − 5.5 V EN high, no load, no switching, PFM Mode − 30 − mA EN low − − 1 mA (Note 7) 0.6 − VIN V PWM Mode 594 600 606 mV FB Voltage in Load Regulation VIN = 3.6 V, IOUT from 200 mA to IOUTMAX, PWM mode (Note 7) − −0.5 − %/A FB Voltage in Line Regulation IOUT = 200 mA, VIN from MAX (VNOM + 0.5 V, 2.3 V) to 5.5 V, PWM mode (Note 7) − 0 − %/V (Note 7) − 100 − % (Note 7) 2.0 − − A 2.3 2.8 3.3 A SUPPLY VOLTAGE VIN Input Voltage VIN Range SUPPLY CURRENT IQ VIN Quiescent Supply Current ISD VIN Shutdown Current OUTPUT VOLTAGE VOUT VFB DMAX Output Voltage Range FB Voltage Maximum Duty Cycle OUTPUT CURRENT IOUTMAX Output Current Capability ILIM Output Peak Current Limit VOLTAGE MONITOR VINUV− VIN UVLO Falling Threshold − − 2.3 V VINHYS VIN UVLO Hysteresis 60 − 200 mV VOUT falls down to cross the threshold (percentage of FB voltage) (Note 8) 87 90 92 % VOUT rises up to cross the threshold (percentage of Power Good Low Threshold (VPGL) voltage) (Note 8) 0 3 5 % VPGL Power Good Low Threshold VPGHYS Power Good Hysteresis TdPGH1 Power Good High Delay in Start Up From EN rising edge to PG going high. (Note 8) − 1.15 − ms TdPGL1 Power Good Low Delay in Shut Down From EN falling edge to PG going low. (Notes 7 and 8) − 8 − ms TdPGH Power Good High Delay in Regulation From VFB going higher than 95% nominal level to PG going high. Not for the first time in start up. (Notes 7 and 8) − 5 − ms TdPGL Power Good Low Delay in Regulation From VFB going lower than 90% nominal level to PG going low. (Notes 7 and 8) − 8 − ms VPG_L Power Good Pin Low Voltage Voltage at PG pin with 5 mA sink current (Note 8) − − 0.3 V PG_LK Power Good Pin Leakage Current 3.6 V at PG pin when power good valid (Note 8) − − 100 nA INTEGRATED MOSFETs RON_H High−Side MOSFET ON Resistance VIN = 3.6 V (Note 9) VIN = 5 V (Note 9) − 140 130 200 − mW RON_L Low−Side MOSFET ON Resistance VIN = 3.6 V (Note 9) VIN = 5 V (Note 9) − 110 100 140 − mW 7. Guaranteed by design, not tested in production. 8. Power Good function is for NCV6334B devices only. 9. Maximum value applies for TJ = 85°C. 10. Operation above 5.5 V input voltage for extended periods may affect device reliability. http://onsemi.com 4 NCV6334B ELECTRICAL CHARACTERISTICS (VIN = 3.6 V, VOUT = 1.8 V, L = 1 mH, C = 10 mF, typical values are referenced to TJ = 25°C, Min and Max values are referenced to TJ up to 125°C, unless other noted.) Symbol Characteristics Test Conditions Min Typ Max Unit 2.7 3.0 3.3 MHz − 0.4 1 ms SWITCHING FREQUENCY FSW Normal Operation Frequency SOFT START TSS Soft−Start Time Time from EN to 90% of output voltage target CONTROL LOGIC VEN_H EN Input High Voltage 1.1 − − V VEN_L EN Input Low Voltage − − 0.4 V VEN_HYS EN Input Hysteresis − 270 − mV IEN_BIAS EN Input Bias Current 0.1 1 mA 75 500 700 W OUTPUT ACTIVE DISCHARGE R_DIS Internal Output Discharge Resistance from SW to PGND THERMAL SHUTDOWN TSD Thermal Shutdown Threshold − 160 − °C TSD_HYS Thermal Shutdown Hysteresis − 25 − °C http://onsemi.com 5 NCV6334B TYPICAL OPERATING CHARACTERESTICS 1 Isd, Vin SHUTDOWN CURRENT (mA) Isd, Vin SHUTDOWN CURRENT (mA) 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 2.5 3 3.5 4 4.5 5 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 −50 5.5 Figure 3. Standby Current vs. Input Voltage (EN = Low, TA = 255C) Iq, Vin QUIESCENT CURRENT (mA) Iq, Vin QUIESCENT CURRENT (mA) 40 30 20 10 2.5 3 3.5 4 4.5 5 50 75 100 125 150 50 40 30 20 10 0 −50 5.5 −25 0 25 50 75 100 125 150 Vin, INPUT VOLTAGE (V) TA, AMBIENT TEMPERATURE (°C) Figure 5. Quiescent Current vs. Input Voltage (EN = High, Open Loop, VOUT = 1.8 V, TA = 255C) Figure 6. Quiescent Current vs. Temperature (EN = High, Open Loop, VOUT = 1.8 V, VIN = 3.6 V) 100 100 95 95 Vin = 2.7 V 90 80 Vin = 5.5 V 75 70 Vin = 3.6 V 65 85 75 65 55 55 10000 Vin = 3.6 V 70 60 10 100 1000 Iout, OUTPUT CURRENT (mA) Vin = 5.5 V 80 60 1 Vin = 2.7 V 90 85 EFFICIENCY (%) EFFICIENCY (%) 25 60 50 50 0 Figure 4. Standby Current vs. Temperature (EN = Low, VIN = 3.6 V) 60 0 −25 TA, AMBIENT TEMPERATURE (°C) Vin, INPUT VOLTAGE (V) 50 1 Figure 7. Efficiency vs. Output Current and Input Voltage (VOUT = 1.05 V, TA = 255C) 10 100 1000 Iout, OUTPUT CURRENT (mA) Figure 8. Efficiency vs. Output Current and Input Voltage (VOUT = 1.8 V, TA = 255C) http://onsemi.com 6 10000 NCV6334B TYPICAL OPERATING CHARACTERESTICS 100 90 90 Vin = 5.5 V 85 80 75 70 65 80 75 70 65 60 55 55 1 10 100 1000 Iout, OUTPUT CURRENT (mA) 10000 Vin = 5.5 V 85 60 50 Vin = 4.5 V 95 EFFICIENCY (%) EFFICIENCY (%) 100 Vin = 3.6 V 95 50 1 10 100 1000 Iout, OUTPUT CURRENT (mA) Figure 9. Efficiency vs. Output Current and Input Voltage (VOUT = 3.3 V, TA = 255C) Figure 10. Efficiency vs. Output Current and Input Voltage (VOUT = 4 V , TA = 255C) 1.83 Vin = 5.5 V 1.82 LOAD REGULATION (V) LOAD REGULATION (V) 1.83 Vin = 3.6 V 1.81 1.80 1.79 Vin = 2.7 V 1.78 1.77 10000 0 1.82 1.81 Figure 11. Load Regulation vs. Output Current and Input Voltage (VOUT = 1.8 V, TA = 255C) TA = −40°C 1.80 1.79 TA = 85°C 1.78 1.77 200 400 600 800 1000 1200 1400 1600 1800 2000 Iout, OUTPUT CURRENT (mA) TA = 25°C 0 200 400 600 800 1000 1200 1400 1600 1800 2000 Iout, OUTPUT CURRENT (mA) Figure 12. Load Regulation vs. Output Current and Temperature (VIN = 3.6 V, VOUT = 1.8 V). VOUT 10 mV / Div VOUT 5 mV / Div 25 mV 4 mV SW 2 V / Div SW 2 V / Div Time: 5 ms / Div Time: 500 ns / Div Figure 14. Output Ripple Voltage in PFM Mode (VIN = 3.6 V, VOUT = 1.8 V, IOUT = 10 mA, L=1 mH, COUT = 10 mF) Figure 13. Output Ripple Voltage in PWM Mode (VIN = 3.6 V, VOUT = 1.8 V, IOUT = 1 A, L=1 mH, COUT = 10 mF) http://onsemi.com 7 NCV6334B TYPICAL OPERATING CHARACTERESTICS −70 mV 100 mV VOUT 100 mV / Div 1500 mA VOUT 1.0 V / Div EN 5 V/ Div IOUT 1 A / Div 500 mA 500 mA Iin 100 mA / Div 70 mA SW 2 V / Div SW 5 V / Div Time: 20 ms / Div Time: 100 ms / Div Figure 16. Power Up Sequence and Inrush Current in Input (VIN = 3.6 V, VOUT = 1.8 V, IOUT = 0 A, L = 1 mH, COUT = 10 mF) Figure 15. Load Transient Response (VIN = 3.6 V, VOUT = 1.8 V, IOUT = 500 mA to 1500 mA, L = 1 mH, COUT = 10 mF) VOUT 1.0 V / Div VOUT 1.0 V / Div EN 5 V/ Div EN 5 V/ Div PG 5 V / Div PG 5 V / Div SW 2 V / Div SW 2 V / Div Time: 200 ms / Div Time: 1 ms / Div Figure 18. Power Down Sequence and Active Output Discharge (VIN = 3.6 V, VOUT = 1.8 V, IOUT = 0 A, L = 1 mH, COUT = 10 mF) Figure 17. Power Up Sequence and Power Good (VIN = 3.6 V, VOUT = 1.8 V, IOUT = 0 A, L = 1 mH, COUT = 10 mF) http://onsemi.com 8 NCV6334B DETAILED DESCRIPTION General frequency. In this mode, the output voltage is regulated by pulse frequency modulation of the internal P−MOSFET, and the switching frequency is almost proportional to the loading current. The internal N−MOSFET operates as synchronous rectifier after each on pulse of the P−MOSFET with a very small negative current limit. When the load increases and the inductor current becomes continuous, the controller automatically turns back to the fixed−frequency PWM mode operation. The NCV6334B, a family of voltage−mode synchronous buck converters, which is optimized to supply different sub−systems of portable applications powered by one cell Li−ion or three cell Alkaline/NiCd/NiMH batteries. The devices are able to deliver up to 2 A on an external adjustable voltage. Operation with 3 MHz switching frequency allows employing small size inductor and capacitors. Input supply voltage feedforward control is employed to deal with wide input voltage range. Synchronous rectification and automatic PWM/PFM power save mode offer improved system efficiency. Undervoltage Lockout The input voltage VIN must reach or exceed 2.4 V (typical) before the NCV6334B enables the converter output to begin the start up sequence. The UVLO threshold hysteresis is typically 100 mV. PWM Mode Operation In medium and heavy load range, the inductor current is continuous and the device operates in PWM mode with fixed switching frequency, which has a typical value of 3 MHz. In this mode, the output voltage is regulated by on−time pulse width modulation of an internal P−MOSFET. An internal N−MOSFET operates as synchronous rectifier and its turn−on signal is complimentary to that of the P−MOSFET. Enable The NCV6334B has an enable logic input pin EN. A high level (above 1.1 V) on this pin enables the device to active mode. A low level (below 0.4 V) on this pin disables the device and makes the device in shutdown mode. There is an internal filter with 5 ms time constant. The EN pin is pulled down by an internal 10 nA sink current source. In most of applications, the EN signal can be programmed independently to VIN power sequence. PFM Mode Operation In light load range, the inductor current becomes discontinuous and the device automatically operates in PFM mode with an adaptive fixed on time and variable switching 1.1V EN 0.4V 100us 95% 90% 300us Vout 1.15ms 8us 5us 8us PG 8us Active Discharge Figure 19. Power Good and Active Discharge Timing Diagram http://onsemi.com 9 NCV6334B Power Good Output Cycle−by−Cycle Current Limitation For NCV6334B with a power good output, the device monitors the output voltage and provides a power good output signal at the PG pin. This pin is an open−drain output pin. To indicate the output of the converter is established, a power good signal is available. The power good signal is low when EN is high but the output voltage has not been established. Once the output voltage of the converter drops out below 90% of its regulation during operation, the power good signal is pulled low and indicates a power failure. A 5% hysteresis is required on power good comparator before signal going high again. The NCV6334B protects the device from over current with a fixed−value cycle−by−cycle current limitation. The typical peak current limit ILMT is 2.8 A. If inductor current exceeds the current limit threshold, the P−MOSFET will be turned off cycle−by−cycle. The maximum output current can be calculated by I MAX + I LMT * V OUT @ ǒV IN * V OUTǓ 2 @ V IN @ f SW @ L (eq. 1) where VIN is input supply voltage, VOUT is output voltage, L is inductance of the filter inductor, and fSW is 3 MHz normal switching frequency. Soft−Start A soft start limits inrush current when the converter is enabled. After a minimum 300 ms delay time following the enable signal, the output voltage starts to ramp up in 100 ms (for external adjustable voltage devices) or with a typical 10 V/ms slew rate (for fixed voltage devices). Thermal Shutdown The NCV6334B has a thermal shutdown protection to protect the device from overheating when the die temperature exceeds 160°C. After the thermal protection is triggered, the fault state can be ended by re−applying VIN and/or EN when the temperature drops down below 125°C. Active Output Discharge An output discharge operation is active in when EN is low. A discharge resistor (500 W typical) is enabled in this condition to discharge the output capacitor through SW pin. http://onsemi.com 10 NCV6334B APPLICATION INFORMATION Output Filter Design Considerations to 50% of the maximum output current IOUT_MAX for a trade−off between transient response and output ripple. The inductance corresponding to the given current ripple is The output filter introduces a double pole in the system at a frequency of f LC + 1 2 @ p @ ǸL @ C (eq. 2) L+ The internal compensation network design of the NCV6334B is optimized for the typical output filter comprised of a 1.0 mH inductor and a 10 mF ceramic output capacitor, which has a double pole frequency at about 50 kHz. Other possible output filter combinations may have a double pole around 50 kHz to have optimum operation with the typical feedback network. Normal selection range of the inductor is from 0.47 mH to 4.7 mH, and normal selection range of the output capacitor is from 4.7 mF to 22 mF. ǒVIN * VOUTǓ @ VOUT (eq. 3) V IN @ f SW @ I L_PP The selected inductor must have high enough saturation current rating to be higher than the maximum peak current that is I L_MAX + I OUT_MAX ) I L_PP (eq. 4) 2 The inductor also needs to have high enough current rating based on temperature rise concern. Low DCR is good for efficiency improvement and temperature rise reduction. Table 1 shows some recommended inductors for high power applications and Table 2 shows some recommended inductors for low power applications. Inductor Selection The inductance of the inductor is determined by given peak−to−peak ripple current IL_PP of approximately 20% Table 1. LIST OF RECOMMENDED INDUCTORS FOR HIGH POWER APPLICATIONS Manufacturer Part Number Case Size (mm) L (mH) Rated Current (mA) (Inductance Drop) Structure MURATA LQH44PN2R2MP0 4.0 x 4.0 x 1.8 2.2 2500 (−30%) Wire Wound MURATA LQH44PN1R0NP0 4.0 x 4.0 x 1.8 1.0 2950 (−30%) Wire Wound MURATA LQH32PNR47NNP0 3.0 x 2.5 x 1.7 0.47 3400 (−30%) Wire Wound Table 2. LIST OF RECOMMENDED INDUCTORS FOR LOW POWER APPLICATIONS Manufacturer Part Number Case Size (mm) L (mH) Rated Current (mA) (Inductance Drop) Structure MURATA LQH44PN2R2MJ0 4.0 x 4.0 x 1.1 2.2 1320 (−30%) Wire Wound MURATA LQH44PN1R0NJ0 4.0 x 4.0 x 1.1 1.0 2000 (−30%) Wire Wound TDK VLS201612ET−2R2 2.0 x 1.6 x 1.2 2.2 1150 (−30%) Wire Wound TDK VLS201612ET−1R0 2.0 x 1.6 x 1.2 1.0 1650 (−30%) Wire Wound Output Capacitor Selection operation mode, the three ripple components can be obtained by The output capacitor selection is determined by output voltage ripple and load transient response requirement. For a given peak−to−peak ripple current IL_PP in the inductor of the output filter, the output voltage ripple across the output capacitor is the sum of three ripple components as below. V OUT_PP(C) + I L_PP 8 @ C @ f SW V OUT_PP(ESR) + I L_PP @ ESR V OUT_PP [ V OUT_PP(C) ) V OUT_PP(ESR) ) V OUT_PP(ESL) V OUT_PP(ESL) + (eq. 5) ESL ESL ) L @ V IN (eq. 6) (eq. 7) (eq. 8) and the peak−to−peak ripple current is where VOUT_PP(C) is a ripple component by an equivalent total capacitance of the output capacitors, VOUT_PP(ESR) is a ripple component by an equivalent ESR of the output capacitors, and VOUT_PP(ESL) is a ripple component by an equivalent ESL of the output capacitors. In PWM I L_PP + http://onsemi.com 11 ǒV IN * VOUTǓ @ VOUT V IN @ f SW @ L (eq. 9) NCV6334B In applications with all ceramic output capacitors, the main ripple component of the output ripple is VOUT_PP(C). So that the minimum output capacitance can be calculated regarding to a given output ripple requirement VOUT_PP in PWM operation mode. C MIN + I L_PP 8 @ V OUT_PP @ f SW C IN_MIN + I OUT_MAX @ ǒD * D 2Ǔ V IN_PP @ f SW (eq. 11) where D+ (eq. 10) V OUT (eq. 12) V IN In addition, the input capacitor needs to be able to absorb the input current, which has a RMS value of Input Capacitor Selection I IN_RMS + I OUT_MAX @ ǸD * D 2 One of the input capacitor selection guides is the input voltage ripple requirement. To minimize the input voltage ripple and get better decoupling in the input power supply rail, ceramic capacitor is recommended due to low ESR and ESL. The minimum input capacitance regarding to the input ripple voltage VIN_PP is (eq. 13) The input capacitor also needs to be sufficient to protect the device from over voltage spike, and normally at least a 4.7 mF capacitor is required. The input capacitor should be located as close as possible to the IC on PCB. Table 3. LIST OF RECOMMENDED INPUT CAPACITORS AND OUTPUT CAPACITORS Manufacturer Part Number Case Size C (mF) Rated Voltage (V) MURATA GRM21BR60J226ME39, X5R 0805 1.4 22 6.3 MLCC TDK C2012X5R0J226M, X5R 0805 1.25 22 6.3 MLCC MURATA GRM21BR61A106KE19, X5R 0805 1.35 10 10 MLCC TDK C2012X5R1A106M, X5R 0805 1.25 10 10 MLCC MURATA GRM188R60J106ME47, X5R 0603 0.9 10 6.3 MLCC TDK C1608X5R0J106M, X5R 0603 0.8 10 6.3 MLCC MURATA GRM188R60J475KE19, X5R 0603 0.87 4.7 6.3 MLCC Design of Feedback Network ǒ Ǔ R1 R2 Structure 220 kW for applications with the typical output filter. R2 is the resistance from FB to AGND, which is used to program the output voltage according to equation (14) once the value of R1 has been selected. A capacitor Cfb needs to be employed between the VOUT and FB in order to provide feedforward function to achieve optimum transient response. Normal value range of Cfb is from 0 to 100 pF, and a typical value is 15 pF for applications with the typical output filter and R1 = 220 kW. Table 4 provides reference values of R1 and Cfb in case of different output filter combinations. The final design may need to be fine tuned regarding to application specifications. For NCV6334B devices with an external adjustable output voltage, the output voltage is programmed by an external resistor divider connected from VOUT to FB and then to AGND, as shown in the typical application schematic Figure 1(a). The programmed output voltage is V OUT + V FB @ 1 ) Height Max (mm) (eq. 14) where VFB is equal to the internal reference voltage 0.6 V, R1 is the resistance from VOUT to FB, which has a normal value range from 50 kW to 1 MW and a typical value of Table 4. Reference Values of Feedback Networks (R1 and Cfb) for Output Filter Combinations (L and C) R1 (kW) L (mH) Cfb (pF) 4.7 C (mF) 10 22 0.47 0.68 1 2.2 3.3 4.7 220 220 220 220 330 330 3 5 8 15 15 22 220 220 220 220 330 330 8 10 15 27 27 39 220 220 220 220 330 330 15 22 27 39 47 56 http://onsemi.com 12 NCV6334B LAYOUT CONSIDERATIONS • Arrange a “quiet” path for output voltage sense and Electrical Layout Considerations Good electrical layout is a key to make sure proper operation, high efficiency, and noise reduction. Electrical layout guidelines are: • Use wide and short traces for power paths (such as PVIN, VOUT, SW, and PGND) to reduce parasitic inductance and high−frequency loop area. It is also good for efficiency improvement. • The device should be well decoupled by input capacitor and input loop area should be as small as possible to reduce parasitic inductance, input voltage spike, and noise emission. • SW node should be a large copper pour, but compact because it is also a noise source. • It would be good to have separated ground planes for PGND and AGND and connect the two planes at one point. Directly connect AGND pin to the exposed pad and then connect to AGND ground plane through vias. Try best to avoid overlap of input ground loop and output ground loop to prevent noise impact on output regulation. feedback network, and make it surrounded by a ground plane. Thermal Layout Considerations Good thermal layout helps high power dissipation from a small package with reduced temperature rise. Thermal layout guidelines are: • The exposed pad must be well soldered on the board. • A four or more layers PCB board with solid ground planes is preferred for better heat dissipation. • More free vias are welcome to be around IC and/or underneath the exposed pad to connect the inner ground layers to reduce thermal impedance. • Use large area copper especially in top layer to help thermal conduction and radiation. • Do not put the inductor to be too close to the IC, thus the heat sources are distributed. GND VIN P P P P L ÏÏÏÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏÏÏ ÎÎÎ ÎÎÎ ÎÎÎ ÏÏÏ ÏÏÏ ÏÏÏ P PGND 1 SW 2 AGND F FB A A 3 4 A ÏÏÏ ÏÏÏ ÏÏÏ ÏÏÏ ÎÎÎ ÎÎÎ 8 PVIN 7 AVIN 6 MODE/PG 5 EN P Cout ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ Cin P P P O P P P P P P Cfb F R1 R2 VOUT GND Figure 20. Recommended PCB Layout for Application Boards http://onsemi.com 13 O A NCV6334B PACKAGE DIMENSIONS WDFN8 2x2, 0.5P CASE 511BT ISSUE O A D PIN ONE REFERENCE 2X 0.10 C 2X 0.10 C B NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 MM FROM TERMINAL TIP. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. L ÇÇ ÇÇ ÇÇ L1 E DETAIL A TOP VIEW ÇÇÇ ÇÇÇ ÉÉÉ ÉÉÉ DIM A A1 A3 b D D2 E E2 e K L L1 MOLD CMPD DETAIL B 0.10 C 0.08 C NOTE 4 EXPOSED Cu A A3 A1 A1 SIDE VIEW C D2 DETAIL A 1 8X 4 SEATING PLANE DETAIL B A3 MILLIMETERS MIN MAX 0.70 0.80 0.00 0.05 0.20 REF 0.20 0.30 2.00 BSC 1.50 1.70 2.00 BSC 0.80 1.00 0.50 BSC 0.25 REF 0.20 0.40 −−− 0.15 RECOMMENDED SOLDERING FOOTPRINT* L 8X 1.70 PACKAGE OUTLINE 0.50 E2 K 8 5 e BOTTOM VIEW 8X 2.30 1.00 b 0.10 C A B 0.05 C NOTE 3 1 0.50 PITCH 8X 0.30 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 14 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCV6334B/D