TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 90% EFFICIENT SYNCHRONOUS BOOST CONVERTER WITH 600-mA SWITCH FEATURES • • • • • • • • DESCRIPTION 90% Efficient Synchronous Boost Converter – 75-mA Output Current at 3.3 V From 0.9-V Input – 150-mA Output Current at 3.3 V From 1.8-V Input Device Quiescent Current: 19 µA (Typ) Input Voltage Range: 0.9 V to 5.5 V Adjustable Output Voltage Up to 5.5 V Power-Save Mode Version Available for Improved Efficiency at Low Output Power Load Disconnect During Shutdown Overtemperature Protection Small 6-Pin Thin SOT23 Package APPLICATIONS • • • • • • The TPS6107x devices provide a power supply solution for products powered by either a one-cell, two-cell, or three-cell alkaline, NiCd or NiMH, or one-cell Li-ion or Li-polymer battery. Output currents can go as high as 75 mA while using a single-cell alkaline, and discharge it down to 0.9 V. It can also be used for generating 5 V at 200 mA from a 3.3-V rail or a Li-ion battery. The boost converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using a synchronous rectifier to obtain maximum efficiency. At low load currents the TPS61070 enters the power-save mode to maintain a high efficiency over a wide load current range. At the TPS61071 the power-save mode is disabled, forcing the converter to operate at a fixed switching frequency. The maximum peak current in the boost switch is typically limited to a value of 600 mA. The TPS6107x output voltage is programmed by an external resistor divider. The converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. The device is packaged in a 6-pin thin SOT23 package (DDC). All One-Cell, Two-Cell, and Three-Cell Alkaline, NiCd or NiMH or Single-Cell Li Battery-Powered Products Portable Audio Players PDAs Cellular Phones Personal Medical Products White LED Lighting L1 4.7 µH 0.9-V To VO C1 10 µF SW VOUT R1 VBAT EN FB C2 10 µF VO 3.3 V Up To 100 mA R2 GND TPS61070 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2004, Texas Instruments Incorporated TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. AVAILABLE OUTPUT VOLTAGE OPTIONS TA - 40°C to 85°C (1) OUTPUT VOLTAGE DC/DC POWER-SAVE MODE PACKAGE MARKING Adjustable Enabled AUH Adjustable Disabled AUJ PACKAGE 6-Pin TSOT23 PART NUMBER (1) TPS61070DDC TPS61071DDC The DDC package is available taped and reeled. Add R suffix to device type (e.g., TPS61070DDCR) to order quantities of 3000 devices per reel. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) TPS6107x Input voltage range on SW, VOUT, VBAT, EN, FB -0.3 V to 7 V Operating virtual junction temperature range, TJ -40°C to 150°C Storage temperature range Tstg -65°C to 150°C (1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATINGS TABLE PACKAGE THERMAL RESISTANCE ΘJA POWER RATING TA≤ 25°C DERATING FACTOR ABOVE TA = 25°C DDC 76 °C/W 1315 mW 13 mW/°C RECOMMENDED OPERATING CONDITIONS MIN Supply voltage at VBAT, VI 0.9 Operating free air temperature range, TA Operating virtual junction temperature range, TJ 2 NOM MAX UNIT 5.5 V -40 85 °C -40 125 °C TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 ELECTRICAL CHARACTERISTICS over recommended free-air temperature range and over recommended input voltage range (typical at an ambient temperature range of 25°C) (unless otherwise noted) DC/DC STAGE PARAMETER VI TEST CONDITIONS Minimum input voltage range for start-up RL = 270 Ω Input voltage range, after start-up TA = 25°C MIN TYP MAX 1.1 1.2 0.9 UNIT V 5.5 VO TPS61070 output voltage range 1.8 5.5 V V(FB) TPS61070 feedback voltage 495 500 505 mV f Oscillator frequency 960 1200 1440 kHz I(SW) Switch current limit 500 600 700 mA VOUT= 3.3 V Start-up current limit 0.5 x ISW mA SWN switch-on resistance VOUT= 3.3 V 480 mΩ SWP switch-on resistance VOUT= 3.3 V 600 mΩ Total accuracy (including line and load regulation) 3% Line regulation 1% Load regulation Quiescent current 1% VBAT VOUT Shutdown current IO = 0 mA, V(EN) = VBAT = 1.2 V, VOUT = 3.3 V, TA = 25°C V(EN) = 0 V, VBAT = 1.2 V, TA = 25°C 0.5 1 µA 19 30 µA 0.05 0.5 µA TYP MAX CONTROL STAGE PARAMETER V(UVLO) Undervoltage lockout threshold VIL EN input low voltage VIH EN input high voltage EN input current TEST CONDITIONS MIN V(LBI) voltage decreasing 0.8 V 0.2 × VBAT 0.8 × VBAT Clamped on GND or VBAT UNIT V V 0.01 0.1 µA Overtemperature protection 140 °C Overtemperature hysteresis 20 °C 3 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 PIN ASSIGNMENTS DDC PACKAGE (TOP VIEW) SW 1 6 VBAT GND 2 5 VOUT EN 3 4 FB Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION EN 3 I Enable input (1/VBAT enabled, 0/GND disabled) FB 4 I Voltage feedback for programming the output voltage GND 2 SW 1 I Boost and rectifying switch input VBAT 6 I Supply voltage VOUT 5 O Boost converter output 4 IC ground connection for logic and power TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 FUNCTIONAL BLOCK DIAGRAM (TPS61070) SW Backgate Control VBAT VOUT 5 kΩ VOUT Vmax Control 3 pF Gate Control GND Error Amplifier 160 kΩ 50 kΩ _ FB Regulator + 5 pF Vref = 0.5 V + _ GND Oscillator Control Logic Temperature Control EN GND PARAMETER MEASUREMENT INFORMATION L1 4.7 µH Power Supply C1 SW VOUT R1 VBAT C2 VCC Boost Output FB EN R2 GND TPS6107x List of Components: U1 = TPS61070DDC L1 = Wurth Elektronik 744031004 C1 = 2 x 4.7 F, 0603, X7R/X5R Ceramic C2 = 4 x 4.7 F, 0603, X7R/X5R Ceramic 5 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 TYPICAL CHARACTERISTICS Table of Graphs FIGURE Maximum output current Efficiency Output voltage No load supply current into VOUT Waveforms 6 vs Input voltage 1 vs Output current 2 vs Output current 3 vs Output current 4 vs Input voltage 5 vs Input voltage 6 vs Output current 7 vs Output current 8 vs Input voltage 9 Output voltage in continuous mode (TPS61071) 10 Output voltage in continuous mode (TPS61071) 11 Output voltage in power-save mode (TPS61070) 12 Output voltage in power-save mode (TPS61070) 13 Load transient response (TPS61071) 14 Load transient response (TPS61071) 15 Line transient response (TPS61071) 16 Line transient response (TPS61071) 17 Start-up after enable (TPS61070) 18 Start-up after enable (TPS61070) 19 Start-up after enable (TPS61071) 20 Start-up after enable (TPS61071) 21 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 TYPICAL CHARACTERISTICS EFFICIENCY vs OUTPUT CURRENT 600 100 550 90 500 VO = 3.3 V 70 400 350 VO = 5 V VO = 1.8 V 300 250 200 60 VBAT = 0.9 V 50 40 30 150 TPS61071 VO = 1.8 V 20 100 10 50 0 0.9 0 0.01 1.3 1.7 2.1 2.5 2.9 3.3 3.7 4.1 4.5 4.9 0.10 Figure 2. EFFICIENCY vs OUTPUT CURRENT EFFICIENCY vs OUTPUT CURRENT 100 TPS61070 VO = 3.3 V 90 80 70 70 Efficiency − % 80 60 50 VBAT = 0.9 V 40 VBAT = 1.8 V 100 1k TPS61070 VO = 5 V VBAT = 1.2 V 60 VBAT = 1.8 V VBAT = 2.4 V 50 VBAT = 3.6 V 40 30 30 VBAT = 2.4 V TPS61071 VO = 5 V 20 20 TPS61071 VO = 3.3 V 10 0 0.01 10 Figure 1. 100 90 1 IO − Output Current − mA VI − Input Voltage − V Efficiency − % VBAT = 1.2 V TPS61070 VO = 1.8 V 80 450 Efficiency − % Maximum Output Current − mA MAXIMUM OUTPUT CURRENT vs INPUT VOLTAGE 0.10 1 10 100 IO − Output Current − mA Figure 3. 10 1k 0 0.01 0.10 1 10 100 IO − Output Current − mA 1k Figure 4. 7 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 TYPICAL CHARACTERISTICS (continued) EFFICIENCY vs INPUT VOLTAGE EFFICIENCY vs INPUT VOLTAGE 100 100 95 TPS61070 VO = 5 V 90 90 IO = 5 mA 85 85 Efficiency − % 95 Efficiency − % TPS61070 VO = 3.3 V IO = 5 mA 80 IO = 50 mA 75 IO = 100 mA 70 65 75 70 IO = 60 mA 65 TPS61071 VO = 3.3 V 60 IO = 10 mA 80 IO = 5 mA 60 55 55 50 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 50 TPS61071 VO = 5 V 0.9 1.4 1.9 2.4 VI − Input Voltage − V 3.4 Figure 5. Figure 6. OUTPUT VOLTAGE vs OUTPUT CURRENT OUTPUT VOLTAGE vs OUTPUT CURRENT 3.35 3.9 4.4 4.9 5.1 VBAT = 3.6 V VBAT = 2.4 V TPS61070 VO = 3.3 V TPS61070 VO = 5 V 5.05 VO − Output Voltage − V VO − Output Voltage − V 2.9 VI − Input Voltage − V 3.30 3.25 5 4.95 4.9 TPS61071 VO = 5 V 4.85 TPS61071 VO = 3.3 V 4.8 3.20 1 10 100 IO − Output Current − mA Figure 7. 8 1000 1 10 100 IO − Output Current − mA Figure 8. 1000 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 TYPICAL CHARACTERISTICS (continued) NO LOAD SUPPLY CURRENT INTO VOUT vs INPUT VOLTAGE TPS61071 OUTPUT VOLTAGE IN CONTINUOUS MODE 22 Output Voltage 20 m/div 20 TA = 25C 18 Inductor Current 100 mA/div TA = −40C 16 14 12 VO = 3.3 V VI = 0.9 V to 5.5 V 10 0.9 1.5 2.5 3.5 VI − Input Voltage − V 4.5 5.5 t − Time − 1 s/div Figure 9. Figure 10. TPS61071 OUTPUT VOLTAGE IN CONTINUOUS MODE TPS61070 OUTPUT VOLTAGE IN POWER-SAVE MODE VI = 1.2 V, RL = 330 , VO = 3.3 V Output Voltage 20 mV/div, AC Output Voltage 20 mV/div VI = 3.6 V, RL = 25 , VO = 5 V Inductor Current 100 mA/div, DC Inductor Current 200 mA/div No Load Supply Current Into VOUT − µA VI = 1.2 V, RL = 33 , VO = 3.3 V TA = 85C t − Time − 1 s/div Figure 11. t − Time − 10 s/div Figure 12. 9 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 TYPICAL CHARACTERISTICS (continued) TPS61070 OUTPUT VOLTAGE IN POWER-SAVE MODE TPS61071 LOAD TRANSIENT RESPONSE VI = 1.2 V, IL = 20 mA to 80 mA, VO = 3.3 V Output Voltage 50 mV/div, AC Inductor Current 200 mA/div, DC Output Current 50 mA/div, DC Output Voltage 100 mV/div, AC VI = 3.6 V, RL = 250 , VO = 5 V t − Time − 2 ms/div t − Time − 20 s/div Figure 13. Figure 14. TPS61071 LOAD TRANSIENT RESPONSE TPS61071 LINE TRANSIENT RESPONSE Output Voltage 50 mV/div, AC t − Time − 2 ms/div Figure 15. 10 Input Voltage 500 mV/div, AC VI = 1.8 V to 2.4 V, RL = 33 , VO = 3.3 V Output Voltage 20 mV/div, AC Output Current 50 mA/div, DC VI = 3.6 V, IL = 20 mA to 80 mA, VO = 5 V t − Time − 2 ms/div Figure 16. TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 TYPICAL CHARACTERISTICS (continued) TPS61070 START-UP AFTER ENABLE Output Voltage Enable 2 V/div, DC 5 V/div, DC TPS61071 LINE TRANSIENT RESPONSE Inductor Current 200 mA/div, DC VI = 2.4 V, RL = 33 , VO = 3.3 V Voltage at SW 2 V/div, DC Output Voltage 50 mV/div, AC Input Voltage 500 mV/div, AC VI = 3 V to 3.6 V, RL = 25 , VO = 5 V t − Time − 200 s/div Figure 18. TPS61070 START-UP AFTER ENABLE TPS61071 START-UP AFTER ENABLE Inductor Current 200 mA/div, DC VI = 2.4 V, RL = 33 , VO = 3.3 V Voltage at SW 2 V/div, DC Inductor Current 200 mA/div, DC VI = 3.6 V, RL = 50 , VO = 5 V Output Voltage Enable 1 V/div, DC 5 V/div, DC Figure 17. Voltage at SW 2 V/div, DC Output Voltage Enable 2 V/div, DC 5 V/div, DC t − Time − 2 ms/div t − Time − 400 s/div Figure 19. t − Time − 200 s/div Figure 20. 11 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 TYPICAL CHARACTERISTICS (continued) Inductor Current 200 mA/div, DC VI = 3.6 V, RL = 50 , VO = 5 V Voltage at SW 2 V/div, DC Output Voltage Enable 2 V/div, DC 5 V/div, DC TPS61071 START-UP AFTER ENABLE t − Time − 200 s/div Figure 21. 12 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 DETAILED DESCRIPTION CONTROLLER CIRCUIT The controller circuit of the device is based on a fixed frequency multiple feedforward controller topology. Input voltage, output voltage, and voltage drop on the NMOS switch are monitored and forwarded to the regulator. So, changes in the operating conditions of the converter directly affect the duty cycle and must not take the indirect and slow way through the control loop and the error amplifier. The control loop, determined by the error amplifier, only has to handle small signal errors. The input is the feedback voltage on the FB pin. It is compared with the internal reference voltage to generate an accurate and stable output voltage. The peak current of the NMOS switch is also sensed to limit the maximum current flowing through the switch and the inductor. The typical peak-current limit is set to 600 mA. An internal temperature sensor prevents the device from overheating due to excessive power dissipation. Synchronous Rectifier The device integrates an N-channel and a P-channel MOSFET transistor to realize a synchronous rectifier. Because the commonly used discrete Schottky rectifier is replaced with a low rDS(on) PMOS switch, the power conversion efficiency reaches values above 90%. A special circuit is applied to disconnect the load from the input during shutdown of the converter. In conventional synchronous rectifier circuits, the backgate diode of the high-side PMOS is forward biased in shutdown and allows current flowing from the battery to the output. However, this device uses a special circuit which takes the cathode of the backgate diode of the high-side PMOS and disconnects it from the source when the regulator is not enabled (EN = low). The benefit of this feature for the system design engineer is that the battery is not depleted during shutdown of the converter. No additional components must be added to the design to make sure that the battery is disconnected from the output of the converter. Device Enable The device is put into operation when EN is set high. It is put into a shutdown mode when EN is set to GND. In shutdown mode, the regulator stops switching, all internal control circuitry including the low-battery comparator is switched off, and the load is isolated from the input (as described in the Synchronous Rectifier Section). This also means that the output voltage can drop below the input voltage during shutdown. During start-up of the converter, the duty cycle and the peak current are limited in order to avoid high-peak currents drawn from the battery. Undervoltage Lockout An undervoltage lockout function prevents the device from operating if the supply voltage on VBAT is lower than approximately 0.8 V. When in operation and the battery is being discharged, the device automatically enters the shutdown mode if the voltage on VBAT drops below approximately 0.8 V. This undervoltage lockout function is implemented in order to prevent the malfunctioning of the converter. Soft Start When the device enables, the internal start-up cycle starts with the first step, the precharge phase. During precharge, the rectifying switch is turned on until the output capacitor is charged to a value close to the input voltage. The rectifying switch is current limited during this phase. This also limits the output current under short-circuit conditions at the output. After charging the output capacitor to the input voltage, the device starts switching. If the input voltage is below 1.8 V, the device works with a fixed duty cycle of 70% until the output voltage reaches 1.8 V. Then the duty cycle is set depending on the input output voltage ratio. Until the output voltage reaches its nominal value, the boost switch current limit is set to 50% of its nominal value to avoid high-peak currents at the battery during start-up. As soon as the output voltage is reached, the regulator takes control, and the switch current limit is set back to 100%. 13 TPS61070 TPS61071 SLVS510 – JUNE 2004 www.ti.com DETAILED DESCRIPTION (continued) Power-Save Mode The TPS61070 is capable of operating in two different modes. At light loads, when the inductor current becomes zero, it automatically enters the power-save mode to improve efficiency. In the power-save mode, the converter only operates when the output voltage trips below a set threshold voltage. It ramps up the output voltage with one or several pulses and returns to the power-save mode once the output voltage exceeds the set threshold voltage. If output power demand increases and the inductor current no longer goes below zero, the device again enters the fixed PWM mode. In this mode, there is no difference between the PWM only version TPS61071 and the power-save mode enabled version TPS61070. 14 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 APPLICATION INFORMATION DESIGN PROCEDURE The TPS6107x dc/dc converters are intended for systems powered by a single-cell, up to triple-cell alkaline, NiCd, NiMH battery with a typical terminal voltage between 0.9 V and 5.5 V. They can also be used in systems powered by one-cell Li-ion or Li-polymer with a typical voltage between 2.5 V and 4.2 V. Additionally, any other voltage source with a typical output voltage between 0.9 V and 5.5 V can power systems where the TPS6107x is used. Due to the nature of boost converters, only the output voltage regulation is maintained when the input voltage applied is lower than the programmed output voltage. Programming the Output Voltage The output voltage of the TPS61070 dc/dc converter can be adjusted with an external resistor divider. The typical value of the voltage at the FB pin is 500 mV. The maximum recommended value for the output voltage is 5.5 V. The current through the resistive divider should be about 100 times greater than the current into the FB pin. The typical current into the FB pin is 0.01 µA, and the voltage across R2 is typically 500 mV. Based on those two values, the recommended value for R2 should be lower than 500 kΩ, in order to set the divider current at 1 µA or higher. Because of internal compensation circuitry, the value for this resistor should be in the range of 200 kΩ. From that, the value of resistor R1, depending on the needed output voltage (VO), can be calculated using Equation 1: R1 R2 V O 1 V FB 180 k V O 1 500 mV (1) For example, if an output voltage of 3.3 V is needed, a 1-MΩ resistor should be chosen for R1. If for any reason the value chosen for R2 is significantly lower than 200 kΩ, additional capacitance in parallel to R1 is recommended, because the device can show unstable regulation of the output voltage. The required capacitance value can be calculated using Equation 2: C 3 pF 200 k 1 parR1 R2 (2) L1 SW Power Supply C1 VOUT R1 VBAT C2 VCC Boost Output FB EN R2 GND TPS61070 Figure 22. Typical Application Circuit for Adjustable Output Voltage Option Inductor Selection A boost converter normally requires two main passive components for storing energy during the conversion. A boost inductor and a storage capacitor at the output are required. To select the boost inductor, it is recommended to keep the possible peak inductor current below the current limit threshold of the power switch in the chosen configuration. For example, the current limit threshold of the TPS6107x's switch is 600 mA. The highest peak current through the inductor and the switch depends on the output load, the input (VBAT), and the output voltage (VOUT). Estimation of the maximum average inductor current is done using Equation 3: VOUT I I L O VBAT 0.8 (3) For example, for an output current of 75 mA at 3.3 V, at least 340 mA of average current flows through the inductor at a minimum input voltage of 0.9 V. 15 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 The second parameter for choosing the inductor is the desired current ripple in the inductor. Normally, it is advisable to work with a ripple of less than 20% of the average inductor current. A smaller ripple reduces the magnetic hysteresis losses in the inductor, as well as output voltage ripple and EMI. But in the same way, regulation time rises at load changes. In addition, a larger inductor increases the total system costs. With these parameters, it is possible to calculate the value for the inductor by using Equation 4: VBAT (VOUT VBAT) L I ƒ VOUT L (4) Parameter f is the switching frequency and ∆ IL is the ripple current in the inductor, i.e., 40% × IL. In this example, the desired inductor has the value of 4 µH. With this calculated value and the calculated currents, it is possible to choose a suitable inductor. In typical applications, a 4.7-µH inductance is recommended. The device has been optimized to operate with inductance values between 2.2 µH and 10 µH. Nevertheless, operation with higher inductance values may be possible in some applications. Detailed stability analysis is then recommended. Care must be taken because load transients and losses in the circuit can lead to higher currents as estimated in Equation 4. Also, the losses in the inductor caused by magnetic hysteresis losses and copper losses are a major parameter for total circuit efficiency. The following inductor series from different suppliers have been used with the TPS6107x converters: Table 1. List of Inductors VENDOR TDK Wurth Elektronik EPCOS Cooper Electronics Technologies Taiyo Yuden INDUCTOR SERIES VLF3010 VLF4012 744031xxx 744042xxx B82462-G4 SD18 SD20 CB2016B xxx CB2518B xxx Capacitor Selection Input Capacitor At least a 10-µF input capacitor is recommended to improve transient behavior of the regulator and EMI behavior of the total power supply circuit. A ceramic capacitor or a tantalum capacitor with a 100-nF ceramic capacitor in parallel, placed close to the IC, is recommended. Output Capacitor The major parameter necessary to define the output capacitor is the maximum allowed output voltage ripple of the converter. This ripple is determined by two parameters of the capacitor, the capacitance and the ESR. It is possible to calculate the minimum capacitance needed for the defined ripple, supposing that the ESR is zero, by using Equation 5: I VOUT VBAT C O min ƒ V VOUT (5) Parameter f is the switching frequency and ∆V is the maximum allowed ripple. With a chosen ripple voltage of 10 mV, a minimum capacitance of 4.5 µF is needed. In this value range, ceramic capacitors are a good choice. The ESR and the additional ripple created are negligible. It is calculated using Equation 6: 16 TPS61070 TPS61071 www.ti.com V ESR SLVS510 – JUNE 2004 I O R ESR (6) The total ripple is the sum of the ripple caused by the capacitance and the ripple caused by the ESR of the capacitor. Additional ripple is caused by load transients. This means that the output capacitor has to completely supply the load during the charging phase of the inductor. The value of the output capacitance depends on the speed of the load transients and the load current during the load change. With the calculated minimum value of 4.5 µF and load transient considerations, the recommended output capacitance value is in a 10-µF range. Care must be taken on capacitance loss caused by derating due to the applied dc voltage and the frequency characteristic of the capacitor. For example, larger form factor capacitors (in 1206 size) have their self resonant frequencies in the same frequency range as the TPS6107x operating frequency. So the effective capacitance of the capacitors used is significantly lower. Therefore, the recommendation is to use smaller capacitors in parallel instead of one larger capacitor. Small Signal Stability To analyze small signal stability in more detail, the small signal transfer function of the error amplifier and the regulator, which is given in Equation 7, can be used: 5 (R1 R2) A d (REG) V R2 (1 i 0.8 s) (FB) (7) Layout Considerations As for all switching power supplies, the layout is an important step in the design, especially at high-peak currents and high switching frequencies. If the layout is not carefully done, the regulator could show stability problems as well as EMI problems. Therefore, use wide and short traces for the main current path and for the power ground tracks. The input capacitor, output capacitor, and the inductor should be placed as close as possible to the IC. Use a common ground node for power ground and a different one for control ground to minimize the effects of ground noise. Connect these ground nodes at any place close to the ground pin of the IC. The feedback divider should be placed as close as possible to the ground pin of the IC. To lay out the control ground, it is recommended to use short traces as well, separated from the power ground traces. This avoids ground shift problems, which can occur due to superimposition of power ground current and control ground current. APPLICATION EXAMPLES L1 4.7 µH Power Supply C1 SW VOUT R1 VBAT C2 VCC Boost Output FB EN R2 GND TPS6107x List of Components: U1 = TPS61070DDC L1 = Wurth Elektronik 744031004 C1 = 2 x 4.7 F, 0603, X7R/X5R Ceramic C2 = 2 x 4.7 F, 0603, X7R/X5R Ceramic Figure 23. Power Supply Solution for Maximum Output Power Operating from a Single or Dual Alkaline Cell 17 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 L1 C2 R1 C1 Power Supply VOUT SW 4.7 µH VBAT VCC Boost Output FB R2 EN GND TPS6107x List of Components: U1 = TPS61070DDC L1 = Taiyo Yuden CB2016B4R7M C1 = 1 x 4.7 F, 0603, X7R/X5R Ceramic C2 = 2 x 4.7 F, 0603, X7R/X5R Ceramic Figure 24. Power Supply Solution Having Small Total Solution Size L1 C1 Power Supply VOUT SW 4.7 µH VBAT EN C2 LED Current Up To 30 mA D1 FB R1 GND TPS6107x List of Components: U1 = TPS61070DDC L1 = Taiyo Yuden CB2016B4R7M C1 = 1 x 4.7 F, 0603, X7R/X5R Ceramic C2 = 2 x 4.7 F, 0603, X7R/X5R Ceramic Figure 25. Power Supply Solution for Powering White LEDs in Lighting Applications C5 DS1 C6 1 µF 0.1 µF L1 SW 4.7 µH Power Supply C1 VOUT R1 VBAT C2 VCC2 ~2 x VCC Unregulated Auxiliary Output VCC Boost Output FB EN R2 GND TPS6107x List of Components: U1 = TPS61070DDC L1 = Wurth Elektronik 744031004 C1 = 2 x 4.7 F, 0603, X7R/X5R Ceramic C2 = 2 x 4.7 F, 0603, X7R/X5R Ceramic Figure 26. Power Supply Solution With Auxiliary Positive Output Voltage 18 TPS61070 TPS61071 www.ti.com SLVS510 – JUNE 2004 C5 DS1 C6 1 µF 0.1 µF L1 SW 4.7 µH Power Supply C1 VOUT R1 VBAT C2 VCC2 ~−VCC Unregulated Auxiliary Output VCC Boost Output FB EN R2 GND TPS6107x List of Components: U1 = TPS61070DDC L1 = Wurth Elektronik 744031004 C1 = 2 x 4.7 F, 0603, X7R/X5R Ceramic C2 = 2 x 4.7 F, 0603, X7R/X5R Ceramic Figure 27. Power Supply Solution With Auxiliary Negative Output Voltage THERMAL INFORMATION Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added heat sinks and convection surfaces, and the presence of other heat-generating components affect the power-dissipation limits of a given component. Three basic approaches for enhancing thermal performance follow. • Improving the power dissipation capability of the PCB design • Improving the thermal coupling of the component to the PCB • Introducing airflow in the system The maximum recommended junction temperature (TJ) of the TPS6107x devices is 125°C. The thermal resistance of the 6-pin thin SOT package (DDC) is RΘJA = 76°C/W. Specified regulator operation is assured to a maximum ambient temperature TA of 85°C. Therefore, the maximum power dissipation is about 520 mW. More power can be dissipated if the maximum ambient temperature of the application is lower. T T J(MAX) A P 125°C 85°C 520 mW D(MAX) R 76 °CW JA (8) 19 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2004, Texas Instruments Incorporated