Ordering number : ENA0438E
LV8044LP
LV8044LQ
Bi-CMOS IC
For Digital Still Camera
6-channel Motor Driver IC
Overview
The LV8044LP and LV8044LQ is a 6-channel motor driver IC for digital still camera.
Functions
• Two microstep drive H-bridge driver channels.
• Two microstep drive/PWM saturated drive switchable H-bridge driver channels.
• Two constant-current drive H-bridge driver channels.
• Drive mode switchable between 2-phase, 1-2 phase full torque, 1-2 phase, and 4W1-2 phase (channels 1, 2, 3, and 4).
• Microstep drive step advance controlled by a single step signal input (channels 1, 2, 3, and 4).
• Ability to set the hold current to one of four levels (channels 1, 2, 3, and 4).
• Ability to set the constant-current reference voltage to one of 16 levels from the serial data (channels 5 and 6).
• Eight-bit 3-wire serial control.
• Three on-chip photosensor driver circuits.
Specifications
Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
Power supply voltage 1
VM max
6.0
V
Power supply voltage 2
VCC max
6.0
V
Output peak current
IO peak
Each CH tw ≤ 10ms, duty 20%
600
mA
Output continuous current
IO max
Each CH
400
mA
Allowable power dissipation 2
Pd max
LV8044LP With substrate *
1.4
W
LV8044LQ With substrate *
1.35
W
Operating temperature
Topg
-20 to +85
°C
Storage temperature
Tstg
-55 to +150
°C
*: With 40mm × 50mm × 0.8mm glass epoxy substrate (four-layer substrate).
Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high
voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment. The products mentioned herein
shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life,
aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system,
safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives
in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any
guarantee thereof. If you should intend to use our products for new introduction or other application different
from current conditions on the usage of automotive device, communication device, office equipment, industrial
equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the
intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely
responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer ' s products or
equipment.
O1911 SY/O2710 SY/50710 SY / 12408 MS 20071120-S00004 / 32807 MS PC / 71906 MS OT 20060512-S00004 No.A0438-1/26
LV8044LP,LV8044LQ
Recommended Operating Conditions at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
Power supply voltage range 1
VM
2.7 to 5.5
V
Power supply voltage range 2
VCC
2.7 to 5.5
V
Logic input voltage range
VIN
0 to VCC +0.3
V
STEP frequency
FSTEP
STEP1, STEP2
to 64
KHz
PWM frequency
FPWM
STEP3, STEP4
to 100
KHz
Electrical Characteristics at Ta = 25°C, VM = 5V, VCC = 3.3V
Parameter
Standby supply current
Symbol
ISTN
Motor supply current
IM
Logic supply current
ICC
Conditions
Ratings
min
typ
Unit
max
1.0
μA
50
100
μA
2
3
4
mA
2.1
2.35
2.6
V
100
150
200
mV
150
180
200
ST = “L”
ST = “H”, PWM3 = PWM4 = “H”,
IN51 = IN61 = “H”, no load
ST = “H”, PWM3 = PWM4 = “H”,
IN51 = IN61 = “H”, no load
VCC low-voltage cut voltage
VthVCC
Low-voltage hysteresis voltage
VthHIS
Thermal shutdown temperature
TSD
Design guarantee
ΔTSD
Design guarantee
Thermal hysteresis width
°C
°C
40
Microstep Driver (channels 1, 2, 3, and 4)
Output on resistance
Output leak current
IO = 400mA, Upper ON resistance
0.7
0.8
Rond
IO = 400mA, Lower ON resistance
0.5
0.6
Ω
1.0
μA
IOleak1
Diode forward voltage 1
VD1
ID = -400mA
Logic pin input current
IinL
VIN = 0V (ST, STEP1, STEP2)
IinH
VIN = 3.3V (ST, STEP1, STEP2)
20
2.5
Logic input “H” level voltage
Vinh
ST, STEP1, STEP2
Logic input “L” level voltage
Vinl
ST, STEP1, STEP2
Current
4W1-2 phase
Ω
Ronu
Vstep16
selection
Step 16
0.9
33
1.2
V
1.0
μA
50
μA
1.0
V
V
0.185
0.200
0.215
V
(Initial level: the channel 1 comparator level)
reference
Vstep15
Step 15 (Initial+1)
0.185
0.200
0.215
V
voltage level
Vstep14
Step 14 (Initial+2)
0.185
0.200
0.215
V
Vstep13
Step 13 (Initial+3)
0.176
0.193
0.206
V
Vstep12
Step 12 (Initial+4)
0.170
0.186
0.200
V
Vstep11
Step 11 (Initial+5)
0.162
0.178
0.192
V
Vstep10
Step 10 (Initial+6)
0.154
0.171
0.184
V
Vstep9
Step 9 (Initial+7)
0.146
0.163
0.176
V
Vstep8
Step 8 (Initial+8)
0.129
0.148
0.159
V
Vstep7
Step 7 (Initial+9)
0.113
0.131
0.143
V
Vstep6
Step 6 (Initial+10)
0.097
0.115
0.127
V
Vstep5
Step 5 (Initial+11)
0.079
0.097
0.109
V
Vstep4
Step 4 (Initial+12)
0.062
0.079
0.092
V
Vstep3
Step 3 (Initial+13)
0.044
0.06
0.074
V
Vstep2
Step 2 (Initial+14)
0.024
0.04
0.054
V
Vstep1
Step 1 (Initial+15)
0.006
0.02
0.036
V
Step 16
0.185
0.200
0.215
V
Step 8 (Initial+1)
0.129
0.148
0.159
V
Step 16
0.185
0.200
0.215
V
1-2 phase
Vstep16
(Initial level: the channel 1 comparator level)
Vstep8
1-2 phase
Vstep16
(Full torque)
2 phase
(Initial level: the channel 1 comparator level)
Vstep8
Step 8 (Initial+1)
0.185
0.200
0.215
V
Vstep8
Step 8
0.185
0.200
0.215
V
Continued on next page.
No.A0438-2/26
LV8044LP,LV8044LQ
Continued from preceding page.
Parameter
Chopping frequency
Current setting reference voltage
Symbol
Conditions
Ratings
min
typ
Unit
max
fchop1
104
130
156
KHz
fchop2
52
65
78
KHz
fchop3
160
200
240
KHz
fchop4
80
100
120
KHz
VSEN00
(D5, D6) = (0, 0)
0.185
0.200
0.215
V
VSEN01
(D5, D6) = (0, 1)
0.119
0.134
0.149
V
VSEN10
(D5, D6) = (1, 0)
0.085
0.100
0.115
V
VSEN11
(D5, D6) = (1, 1)
0.051
0.066
0.081
V
Ω
Constant-Current Drive (channels 5 and 6)
Output on resistance
Output leak current
Ronu
IO = 400mA, Upper ON resistance
0.7
0.8
Rond
IO = 400mA, Lower ON resistance
0.5
0.6
Ω
1.0
μA
IOleak
Diode forward voltage 1
VD1
ID = -400mA
Logic pin input current
IinL
VIN = 0V, (IN51, IN52, IN61, IN62)
IinH
VIN = 3.3V, (IN51, IN52, IN61, IN62)
20
2.5
Logic input “H” level voltage
Vinh
IN51, IN52, IN61, IN62
Logic input “L” level voltage
Vinl
IN51, IN52, IN61, IN62
Output constant current
IOUT
Rload = 3Ω,RF = 0.5Ω,
0.9
33
1.2
V
1.0
μA
50
μA
1.0
V
mA
V
380
400
420
Internal standard = 0.2V
Current setting reference voltage
Vref0
(D4, D5, D6, D7) = (0, 0, 0, 0)
0.285
0.30
0.315
V
Vref1
(D4, D5, D6, D7) = (1, 0, 0, 0)
0.19
0.20
0.21
V
Vref2
(D4, D5, D6, D7) = (0, 1, 0, 0)
0.18
0.190
0.2
V
Vref3
(D4, D5, D6, D7) = (1, 1, 0, 0)
0.171
0.180
0.189
V
Vref4
(D4, D5, D6, D7) = (0, 0, 1, 0)
0.161
0.170
0.179
V
Vref5
(D4, D5, D6, D7) = (1, 0, 1, 0)
0.156
0.165
0.173
V
Vref6
(D4, D5, D6, D7) = (0, 1, 1, 0)
0.152
0.160
0.168
V
Vref7
(D4, D5, D6, D7) = (1, 1, 1, 0)
0.147
0.155
0.163
V
Vref8
(D4, D5, D6, D7) = (0, 0, 0, 1)
0.143
0.150
0.158
V
Vref9
(D4, D5, D6, D7) = (1, 0, 0, 1)
0.137
0.145
0.152
V
VrefA
(D4, D5, D6, D7) = (0, 1, 0, 1)
0.133
0.140
0.147
V
VrefB
(D4, D5, D6, D7) = (1, 1, 0, 1)
0.128
0.135
0.142
V
VrefC
(D4, D5, D6, D7) = (0, 0, 1, 1)
0.123
0.130
0.137
V
VrefD
(D4, D5, D6, D7) = (1, 0, 1, 1)
0.114
0.120
0.126
V
VrefE
(D4, D5, D6, D7) = (0, 1, 1, 1)
0.104
0.110
0.116
V
VrefF
(D4, D5, D6, D7) = (1, 1, 1, 1)
0.095
0.100
0.105
V
Vsat
IO = -20mA
0.09
0.12
V
1.0
μA
50
μA
Photo-sensor Drive Circuit
Output saturation voltage
Serial Data Transfer Pin
Logic pin input current
IinL
VIN = 0V (SCLK, SDATA, STB)
IinH
VIN = 3.3V (SCLK, SDATA, STB)
20
Vinh
SCLK, SDATA, STB
2.5
Logic input “L” level voltage
Vinl
SCLK, SDATA, STB
Minimum SLCK “H” pulse width
Tckh
0.125
μs
Minimum SLCK “L” pulse width
Tckl
0.125
μs
Tsup1
0.125
μs
Tsup2
0.125
μs
Tstbw
0.125
μs
Tds
0.125
μs
Data hold time
Tdh
0.125
Maximum SCLK frequency
Fclk
Logic input “H” level voltage
Minimum setup time
33
V
1.0
V
(STB → SCLK rising edge)
Minimum setup time
(SCLK rising edge →STB)
Minimum STB pulse width
Data setup time
μs
4
MHz
No.A0438-3/26
LV8044LP,LV8044LQ
Serial Input Switching Characteristics Timing Chart
Fclk
Tsup1
Tckh
Tckl
SCLK
Tds Tdh
D0
SDATA
D1
D2
D6
D7
Tsup2
STB
Tstbw
Package Dimensions
unit : mm (typ)
3302A
[LV8044LP] 3351
TOP VIEW
TOP VIEW
BOTTOM VIEW
SIDE VIEW
5.0
[LV8044LQ]
BOTTOM VIEW
SIDE VIEW
5.0
0.35
0.4
40
2 1
0.2
SIDE VIEW
SANYO : UQLP40(5.0X5.0)
SANYO : VQLP40(5.0X5.0)
Allowable power dissipation, Pd max -- W
1.4
1.2
0.8
0.73
0.4
0
-20
0
20
40
60
Ambient temperature, Ta -- °C
80 85
100
Pd max -- Ta
1.6
Allowable power dissipation, Pd max -- W
Pd max -- Ta
[LV8044LP]
Specified substrate: 40×50×0.8mm3
glass epoxy four-layer board.
1.6
(0.7)
0.2
0.65 MAX
(0.7)
0.0 NOM
0.85 MAX
0.0 NOM
2 1
SIDE VIEW
(0.7)
40
(0.7)
0.4
5.0
5.0
0.35
0.35
0.35
[LV8044LQ]
Specified substrate: 40×50×0.8mm3
glass epoxy four-layer board.
1.35
1.2
0.8
0.70
0.4
0
-20
0
20
40
60
80 85
100
Ambient temperature, Ta -- °C
No.A0438-4/26
LV8044LP,LV8044LQ
28
27
26
25
24
23
22
RF6
OUT6A
OUT4B
RF4
OUT4A
OUT3B
RF3
21
OUT3A
29
OUT6B
31 IN62
30
PGND2
Pin Assignment
PWM3/
20
STEP2
32 IN61
PWM4 19
33 VM6
VM34 18
VCC 17
34 SGND
LV8044LP
LV8044LQ
35 PI1
STB 16
SDATA 15
36 PI2
TOP VIEW
37 PI3/MO
SCLK 14
OUT2B
RF2
OUT2A
OUT1B
RF1
OUT1A
40 IN51
OUT5A
VM12 12
RF5
39 IN52
OUT5B
STEP1 13
PGND1
38 VM5
1
2
3
4
5
6
7
8
9
10
ST 11
The pin assignment of LV8044LP and LV8044LQ is the same.
No.A0438-5/26
SGND
VCC
PGND1
RF1
Current selection
LVS
TSD
VM12
STEP1
OUT2B
Oscillator
Current selection
(4W1-2/1-2/
1-2Full/2)
OUT2A
Output control logic
OUT1B
(4W1-2/1-2/
1-2Full/2)
OUT1A
Monitor
selector
SCLK
SDATA
STB
(4W1-2/1-2/
1-2Full/2)
ST
VM34
OUT4A
STEP2
/PWM3
PWM4
(4W1-2/1-2/
1-2Full/2)
OUT4B
Current selection
Output control logic
OUT3B
Current selection
RF3 OUT3A
Serial-to-parallel
converter (8 bits)
RF2
OUT5B
Reference
voltage
circuit (0.3 V)
MO/PI3
RF5
Reference voltage
selection circuit
(0.1 to 0.3 V in 16 steps)
Output control
logic
VM5 OUT5A
IN51 IN52 IN61 IN62
RF4
RF6
PI1 V
PI2
CC
OUT6B
Output control
logic
VM6 OUT6A
PGND2
LV8044LP,LV8044LQ
Block Diagram
No.A0438-6/26
LV8044LP,LV8044LQ
Pin Function
Pin No.
Pin name
13
STEP1
20
PWM3/STEP2
Function
Equivalent circuit
Channels 1/2 - STEP signal input
3ch PWM signal input
/ Channels 3/4 - STEP signal input
19
PWM4
40
IN51
39
IN52
4ch PWM signal input
Channel 5 - Logic input 1
32
IN61
31
IN62
Channel 6- Logic input 1
14
SCLK
15
SDATA
16
STB
11
ST
10
OUT1A
1ch
7
OUT2A
2ch
21
OUT3A
3ch
24
OUT4A
4ch
4
OUT5A
5ch
27
OUT6A
6ch
8
OUT1B
1ch
Serial data transfer clock input
Serial data input
Serial data latch pulse input
Chip enable
5
OUT2B
2ch
23
OUT3B
3ch
26
OUT4B
4ch
2
OUT5B
5ch
29
OUT6B
6ch
9
RF1
1ch
6
RF2
2ch
22
RF3
3ch
25
RF4
4ch
5ch
OUTA output
OUTB output
Current sensing resistor connection
3
RF5
28
RF6
12
VM12
Channels 1/2 - Motor power supply
18
VM34
Channels 3/4 - Motor power supply
38
VM5
Channels 5 - Motor power supply
33
VM6
Channels 6 - Motor power supply
35
PI1
Photosensor drive output
36
PI2
6ch
Continued on next page.
No.A0438-7/26
LV8044LP,LV8044LQ
Continued from preceding page.
Pin No.
Pin name
37
PI3/MO
Function
Equivalent circuit
Photosensor drive output 3/position detection monitor
17
VCC
1
PGND1
Logic system power supply
30
PGND2
Channels 3/4/6 - Power system ground
34
SGND
Signal system ground
Channels 1/2/5 - Power system ground
Serial Data Input Specifications
1. Serial Data Input Setup
First set STB low and then input the SDATA and SCLK signals. The SCLK signal is not accepted when STB is high.
SDATA inputs the data in the order D0, D1, ... D6, D7.
Data is transferred on the rising edge of SCLK and after all data has been transferred, all the data is latched on the rising
edge of STB.
2. Timing with which the Serial Data Settings are Reflected in the Output
• STP timing mode (applies to microstep driver settings)
Type 1: The hold, reset, and enable settings, as well as the reference voltage setting are reflected at the same time as
the STB signal data latch operation.
Type 2: The forward/reverse (FR) and the excitation setting mode (MS) setting that are set at STP setup are reflected
in the output at the next clock rising edge after data latch.
• STB timing (applies to settings other than the above)
Type 1: The PWM driver, constant-current driver, PI, and other settings are reflected at the same time as the STB signal
data latch operation.
No.A0438-8/26
LV8044LP,LV8044LQ
Serial Data Truth Table
Serial Logic Table (1)
Input
Setting mode
Description
D0 D1 D2 D3 D4 D5 D6 D7
0
1
0
0
0
0
0
0
*
*
*
1
0
*
*
*
*
*
*
1ch 2ch 3ch 4ch 5ch 6ch
Channels 1 and 2
excitation
1
1
*
*
*
4W1-2 phase
*
*
0
0
*
100% (0.2V)
*
*
1
0
*
*
*
0
1
*
*
*
1
1
*
*
*
*
*
0
*
*
*
*
1
0
*
*
*
*
1/2ch energization
CW (Forward)
1
*
*
*
*
direction
CCW (Reverse)
*
0
*
*
*
*
1
*
*
*
*
*
0
*
*
*
*
1
*
*
*
*
0
*
*
*
1
*
*
*
*
*
0
*
*
*
*
1
timing
PI
STEP1 STEP2
STB
1-2 phase (full torque)
1
*
Remarks
Serial data reflection
2 phase
0
*
Set channel
mode selection
Channels 1 and 2
current reference
voltage selection
{
1-2 phase
{
{
67% (0.134V)
{
50% (0.1V)
33% (0.066V)
(Dummy data)
{
Cancel
1/2ch step hold
Hold
Reset
1/2ch counter reset
Cancel
{
{
{
Output OFF
1/2ch output enable
Output ON
(Dummy data)
No.A0438-9/26
LV8044LP,LV8044LQ
Serial Logic Table (2)
Input
Setting mode
Description
D0 D1 D2 D3 D4 D5 D6 D7
0
1
0
0
0
*
*
*
1
0
*
*
*
0
1
*
*
*
1
1
*
*
*
*
*
0
0
*
*
*
1
0
*
*
*
0
1
*
*
*
1
1
*
*
*
*
*
0
*
*
*
*
1
Remarks
Set channel
1ch 2ch 3ch 4ch 5ch 6ch
Serial data reflection
PI
timing
STEP1 STEP2
STB
2 phase
3/4ch
excitation
mode selection
1-2 phase (full torque)
{
1-2 phase
4W1-2 phase
100% (0.2V)
3/4ch
current reference
voltage selection
67% (0.134V)
{
{
50% (0.1V)
33% (0.066V)
3/4ch
PWM
Channels 3 and 4
Microstep
{
saturation/microstep
selection
0
0
*
*
*
1
0
*
*
*
0
1
*
*
*
1
1
*
*
*
*
*
0
0
*
*
*
1
0
*
*
1
1
0
*
OFF
3ch energization
direction
(Saturated mode)
OUT3A → OUT3B
OUT3B → OUT3A
{
Brake
OFF
4ch energization
direction
{
OUT4B → OUT4A
*
0
1
*
*
1
1
*
*
*
*
*
0
3/4ch PWM DECAY
Brake
Standby mode
CW (Forward)
(Saturated mode)
{
OUT4A → OUT4B
Brake
*
*
*
*
1
(Saturated mode)
0
*
*
*
*
1
*
*
*
*
3/4ch energization
direction
(Microstep mode)
CCW (Reverse)
*
0
*
*
*
3/4ch step hold
Cancel
*
1
*
*
*
(Microstep mode)
Hold
*
*
0
*
*
3/4ch counter reset
Reset
*
*
1
*
*
(Microstep mode)
Cancel
*
*
*
0
*
3/4ch output enable
Output OFF
*
*
*
1
*
(Microstep mode)
Output ON
*
*
*
*
0
*
*
*
*
1
{
{
{
{
{
{
(Dummy data)
No.A0438-10/26
LV8044LP,LV8044LQ
Serial Logic Table (3)
Input
Setting mode
Description
Remarks
D0 D1 D2 D3 D4 D5 D6 D7
0
1
0
0
1
1
Serial data reflection
Set channel
PI
1ch 2ch 3ch 4ch 5ch 6ch
timing
STEP1 STEP2
STB
OFF
0
0
*
*
*
1
0
*
*
*
5ch energization
OUT5A → OUT5B
direction
OUT5B → OUT5A
0
1
*
*
*
1
1
*
*
*
Brake
*
*
0
0
*
OFF
*
*
1
0
*
6ch energization
OUT6A → OUT6B
*
*
0
1
*
direction
OUT6B → OUT6A
*
*
1
1
*
*
*
*
*
0
*
*
*
*
1
0
*
*
*
*
Reference setting
5ch setting
channel selection
6ch setting
*1
{
{
*2
{
Brake
(Dummy data)
1
*
*
*
*
*
0
0
0
0
0.300V
*
1
0
0
0
0.200V
*
0
1
0
0
0.190V
*
1
1
0
0
0.180V
*
0
0
1
0
0.170V
*
1
0
1
0
0.165V
*
0
1
1
0
0.160V
*
1
1
1
0
Constant-current
0.155V
*
0
0
0
1
reference voltage
0.150V
*
1
0
0
1
0.145V
*
0
1
0
1
0.140V
*
1
1
0
1
0.135V
*
0
0
1
1
0.130V
*
1
0
1
1
0.120V
*
0
1
1
1
0.110V
*
1
1
1
1
0.100V
{
{
{
No.A0438-11/26
LV8044LP,LV8044LQ
Serial Logic Table (4)
Input
Setting mode
Description
Remarks
D0 D1 D2 D3 D4 D5 D6 D7
0
1
1
1
1
1
0
*
*
*
*
1
*
*
*
*
*
0
*
*
*
*
1
*
*
*
*
*
0
*
*
*
*
1
*
*
*
*
*
0
*
*
*
*
1
*
*
*
*
*
0
*
*
*
*
1
0
*
*
*
*
1
*
*
*
*
*
0
*
*
*
*
1
*
*
*
*
*
0
*
*
*
*
1
*
*
*
*
*
0
0
*
*
*
1
0
*
*
*
0
1
*
*
*
1
1
Set channel
Serial data reflection
PI
1ch 2ch 3ch 4ch 5ch 6ch
timing
STEP1 STEP2
STB
OFF
Photo-sensor drive 1
Photo-sensor drive 2
Photo-sensor drive 3
(When PI3 output
selected)
ON
OFF
{
ON
{
OFF
ON
(Dummy data)
(Dummy data)
PI3/MO select
MO output channel
selection
(When MO output
selected)
MO output position
PI3 Output
MO output
1/2ch
3/4ch
*3
Initial position
1-2 phase
*4
{
{
130KHz
Chopping frequency
setting
65KHz
200KHz
100KHz
Notes
*1: This serial data is only accepted when the IN51/IN52 pulse inputs are in the Low/Low states, respectively. It is
ignored at all other times.
*2: This serial data is only accepted when the IN61/IN62 pulse inputs are in the Low/Low states, respectively. It is
ignored at all other times.
*3: When D4 = 1, MO is only output if microstep mode is selected for channels 3 and 4. In PWM mode, this output is held
fixed at the high level.
*4: The MO output can be specified to be the 1-2 phase position only in 4W1-2 phase excitation mode. In all other
excitation modes, the MO output position becomes the initial position regardless of the serial data values.
No.A0438-12/26
LV8044LP,LV8044LQ
Channels 1 and 2 Driver Circuit (Microstep drive stepping mode driver)
STEP1 Pin Function
Input
ST
STEP1
Low
*
High
Operating mode
Standby mode
Excitation step feed
High
Excitation step hold
Excitation Mode Setting (D0 = 0, D1 = 0, D2 = 0)
D3
D4
Excitation mode
0
0
1
0
1
Initial position
1ch
2ch
2 phase excitation
100%
-100%
0
1-2 phase excitation (full torque)
100%
0%
1
1-2 phase excitation
100%
0%
1
4W1-2 phase excitation
100%
0%
The initial state at power on is the initial position for each excitation mode when the counter is reset.
Reference Voltage Setting Serial Data: (D0 = 0, D1 = 0, D2 = 0)
D5
D6
0
0
Current setting reference voltage (When microstep is 100%)
0.2V
1
0
0.134V
0
1
0.1V
1
1
0.066V
The output current setting reference voltage can be switched between four levels with the serial data.
This setting is useful for saving power in the motor powered hold state.
Calculating the Set Current
Since the reference voltage can be modified (0.2, 0.134, 0.1, and 0.66V) with the serial data, the output current can be
set with the reference voltage and the resistor RF connected between the RF pin and ground.
IOUT = (<reference voltage> × <set current ratio>)/<RF resistor value>
Example: If the reference voltage is 0.2 V, the set current ratio is 100%, and the RF resistor value is 1Ω, then the output
current will be that shown below.
IOUT = 0.2V × 100%/1Ω = 200mA
No.A0438-13/26
LV8044LP,LV8044LQ
Output Current Vector Locus (With one step normalized to 90 degrees)
Set Current Ratios in the Different Excitation Modes
STEP
4W1-2 phase (%)
1ch
1-2 phase (%)
2ch
1ch
θ0
0
100
θ1
10
100
θ2
20
100
θ3
30
96.5
θ4
39.5
93.0
θ5
48.5
89
θ6
57.5
85.5
θ7
65.5
81.5
θ8
74.0
74.0
θ9
81.5
65.5
θ10
85.5
57.5
θ11
89
48.5
θ12
93.0
39.5
θ13
96.5
30
θ14
100
20
θ15
100
10
θ16
100
0
1-2 phase full torque (%)
2ch
1ch
2ch
2 phase (%)
1ch
0
100
0
100
74.0
74.0
100
100
100
0
100
0
100
2ch
100
No.A0438-14/26
LV8044LP,LV8044LQ
2 Phase Excitation (CW mode)
1-2 Phase Excitation full torque (CW mode)
1-2 Phase Excitation (CW mode)
No.A0438-15/26
LV8044LP,LV8044LQ
4W1-2 Phase Excitation (CW mode)
No.A0438-16/26
LV8044LP,LV8044LQ
Current Control Operation Specifications
• Sine wave increasing direction
STEP
Set current
Coil current
Set current
fchop
Current
mode
CHARGE
SLOW
FAST
CHARGE
SLOW
FAST
• Sine wave decreasing direction
STEP
Set current
Coil current
Set current
fchop
Current
mode
CHARGE
SLOW
FAST
CHARGE
FAST
CHARGE
SLOW
Each of the current modes operates with the follow sequence.
• The IC enters charge mode when the chopping oscillation starts. (A period of charge mode is forcibly present in 1/8
of the period, regardless of which of the coil current (ICOIL) and the set current (IREF) is larger.)
• In charge mode, the coil current (ICOIL) and the set current (IREF) are compared.
If an ICOIL < IREF state exists during the charge period:
The IC operates in charge mode until ICOIL ≥ IREF. After that, it switches to slow decay mode and then switches to
fast decay mode in the last 1/8 of the period.
If no ICOIL < IREF state exists during the charge period:
The IC switches to fast decay mode and the coil current is attenuated with the fast decay operation until the end of the
chopping period.
The above operation is repeated. Normally, in the sine wave increasing direction the IC operates in slow (+fast) decay
mode, and in the sine wave decreasing direction the IC operates in fast decay mode until the current is attenuated and
reaches the set value and the IC operates in slow decay mode.
No.A0438-17/26
LV8044LP,LV8044LQ
Chopping Frequency Setting (D6 and D7 in the serial data)
This IC integrates an internal oscillator circuit and allows the chopping frequency used in constant-current control to be
switched with the serial data (111***, D6, D7) setting.
Data D6
Data D7
Chopping frequency
0
0
130KHz
1
0
65KHz
0
1
200KHz
1
1
100KHz
Monitor Output Setting (Serial data bits D3, D4, and D5)
The signal output from the PI3/MO pin can be switched with the serial data (111, D3, ****) setting.
Data D3
PI3/MO pin output
0
Photosensor drive output 3
1
Stepping position detection monitor output
It is also possible to select which of channels 1 and 2 or channels 3 and 4 are output from the monitor pin with the serial
data (111*, D4, D5, **) setting. The MO output position used to detect the driver excitation position in microstepping
drive mode can also be switched. The state MO = Low is output at the output position.
Data D4
Data D5
0
0
0
1
Channels 1 and 2
Channels 3 and 4 excitation
excitation mode
mode
MO output
2 phase excitation
Channels 1 and 2 monitor/initial position
Channels 1 and 2 monitor/initial position
0
0
1-2 phase excitation
0
1
(full torque)
0
0
1-2 phase excitation
Channels 1 and 2 monitor/initial position
0
1
4W1-2 phase excitation
Channels 1 and 2 monitor/initial position
0
0
0
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
1
1
Channels 1 and 2 monitor/1-2 phase position
2 phase excitation
Channels 3 and 4 monitor/initial position
1-2 phase excitation (full torque)
Channels 3 and 4 monitor/initial position
1-2 phase excitation
Channels 3 and 4 monitor/initial position
4W1-2 phase excitation
Channels 3 and 4 monitor/initial position
Channels 3 and 4 monitor/1-2 phase position
PWM drive mode
Output held fixed at the high level
No.A0438-18/26
LV8044LP,LV8044LQ
Basic Set Current Step Switching (STEP pin) and Forward/Reverse Switching (D3 in the serial data)
Operations
The IC internal D/A converter advances by 1 bits on the rising edge of the input step pulse.
The CW/CCW mode can be switched with the serial data (100, D3, ****) setting. The operation progresses with the
position number decreasing in CW mode and increasing in CCW mode.
In CW mode, the channel 2 current phase is delayed by 90 degrees relative to the channel 1 current.
In CCW mode, the channel 2 current phase is advanced by 90 degrees relative to the channel 1 current.
No.A0438-19/26
LV8044LP,LV8044LQ
Excitation Mode Switching During Operation (D3 and D4 in the serial data)
If the excitation mode is switched when power is applied to the motor, the operation follows the sequence shown below.
(CW mode)
Before excitation mode switching
Excitation mode
Position
Step position after excitation mode switching
4W1-2 phase
1-2 phase
2 phase full
2 phase
torque
4W1-2 phase
1-2 phase
2 phase full torque
2 phase
(16)
(8)
(8)’
(8)’
(15) to (9)
(8)
(8)’
(8)’
(8)’
(8)
0
0
(7) to (1)
(8)
(8)’
(8)’
0
-(8)
-(8)’
-(8)’
(8)’
(16)
(15)
(8)’
(8)
(7)
0
(8)’
0
-(1)
-(8)’
-(8)’
(16)
(15)
(8)
(8)’
(7)
0
(8)’
0
-(1)
-(8)
-(8)’
(8)’
(7)
0
(8)’
0
No.A0438-20/26
LV8044LP,LV8044LQ
Output Enable Function (D6 in the serial data)
When the OE bit in the serial data, D6 (100, ***, D6, *), is set to 0, the output is turned off and set to the
high-impedance state at the rise of STB.
Since, however, the internal logic circuits operate in this state, the position number will be advanced if a step input is
applied. Therefore, when the OE bit (D6) is returned to 1, a level according to the position number advanced by the step
input will be output.
Counter Reset Function (D5 in the serial data)
When the reset bit in the serial data, D5 (100, **, D5, **), is set to 0, the output goes to the initial state at the rise of STB
and the MO output goes low.
Then, when the reset bit (D5) is next set to 1, the position number will advance at the next step input.
No.A0438-21/26
LV8044LP,LV8044LQ
Step Hold Function (D4 in the serial data)
When the hold bit in the serial data, D4 (100, *, D4, ***), is set to 1, the external step state at that time is held without
change as the internal step state.
Since the (external) step state is low at the timing of the step hold operation (1) in the figure, the internal step state is
held at the low level, and since the (external) step state is high at the timing of the step hold operation (1), the internal
step state is held at the high level.
When the hold data (D) is set to 0, the internal state is synchronized with the external step signal.
The output is held at the state at the point where the step hold was applied and after the step hold is released, it advances
with the timing of the next step input (rising edge).
As long as the IC is in the hold state, the position number does not advance even if external step pulses are applied.
No.A0438-22/26
LV8044LP,LV8044LQ
Channels 3 and 4 Driver Circuit (Saturated drive/microstep drive)
Driver Mode Setting (D0 = 0, D1 = 1, D2 = 0)
D7 data value
Drive mode
Pin functions
Notes
0
Saturated drive
PWM3
Used as the channel 3 PWM input pin
1
Microstep drive
STEP2
Used as the channels 3 and 4 excitation step input pin
The channels 3 and 4 driver circuit can be switched between the following operating modes by bit D7 in the serial data
(010, ****, D7).
(1) Two saturated mode driver channels
(2) One microstep drive stepping motor driver channel
Microstep Drive Stepping Motor Driver
The basic functionality provided is identical to that of the channels 1 and 2 stepping motor driver. See section 10-2 for
details on the serial data settings.
PWM Saturated Mode Driver
Channel 3 Truth Table (PWM mode: D0 = 1, D1 = 1, D2 = 0)
Input
ST
PWM3
D3
Output
D4
D7
OUT3A
Operating mode
OUT3B
Low
*
*
*
*
OFF
OFF
High
Low
0
0
*
OFF
OFF
Standby mode
Output off
High
Low
1
0
*
High
Low
CW (forward)
High
Low
0
1
*
Low
High
CCW (reverse)
High
Low
1
1
*
Low
Low
Brake
High
High
*
*
0
Low
Low
SLOW DECAY (brake)
High
High
*
*
1
OFF
OFF
FAST DECAY (output off)
Channel 4 Truth Table (PWM mode: D0 = 1, D1 = 1, D2 = 0)
Input
ST
PWM4
D5
Output
D6
D7
OUT4A
Operating mode
OUT4B
Low
*
*
*
*
OFF
OFF
High
Low
0
0
*
OFF
OFF
Standby mode
Output off
High
Low
1
0
*
High
Low
CW (forward)
High
Low
0
1
*
Low
High
CCW (reverse)
High
Low
1
1
*
Low
Low
Brake
High
High
*
*
0
Low
Low
SLOW DECAY (brake)
High
High
*
*
1
OFF
OFF
FAST DECAY (output off)
*: Don’t care
No.A0438-23/26
LV8044LP,LV8044LQ
Channels 5 and 6 Driver Circuit (Constant-current drive)
Output Function
When the channels 5 and 6 driver circuit is used to drive an actuator, it can be controlled either from the serial data or
from the IN51, IN52, IN61, and IN62 parallel signals.
When the parallel input signals IN51 (IN61)/IN52 (IN62) are in the low/low state (note that since these inputs are
pulled down internally in the IC, the open/open state can also be used), the output mode will be determined by the serial
data.
If the parallel input signals are in any state other than the above, the serial data will be ignored and the output mode will
be determined by the parallel inputs.
Truth Table (Channel 5: D0 = 0, D1 = 0, D2 = 1)
Parallel input
IN51
IN52
Low
Low
High
Low
Serial data
Outputs
D3
D4
0
1
Mode
OUT5A
OUT5B
0
OFF
OFF
0
High
Low
CW (forward)
0
1
Low
High
CCW (reverse)
1
1
Low
Low
Brake
*
*
High
Low
CW (forward)
Standby mode
Low
High
*
*
Low
High
CCW (reverse)
High
High
*
*
Low
Low
Brake
Truth Table (Channel 6: D0 = 0, D1 = 0, D2 = 1)
Parallel input
IN61
IN62
Low
Low
High
Low
Serial data
Outputs
D5
D6
0
1
Mode
OUT6A
OUT6B
0
OFF
OFF
0
High
Low
CW (forward)
0
1
Low
High
CCW (reverse)
1
1
Low
Low
Brake
*
*
High
Low
CW (forward)
Standby mode
Low
High
*
*
Low
High
CCW (reverse)
High
High
*
*
Low
Low
Brake
*: Don’t care
No.A0438-24/26
LV8044LP,LV8044LQ
Constant-Current Control
Reference Voltage Setting (D0 = 1, D1 = 0, D2 = 1, D3 = 0 (channel 5) or D3 = 1 (channel 6))
D4
D5
D6
D7
Current setting reference voltage
0
0
0
0
0.300V
1
0
0
0
0.200V
0
1
0
0
0.190V
1
1
0
0
0.180V
0
0
1
0
0.170V
1
0
1
0
0.165V
0
1
1
0
0.160V
1
1
1
0
0.155V
0
0
0
1
0.150V
1
0
0
1
0.145V
0
1
0
1
0.140V
1
1
0
1
0.135V
0
0
1
1
0.130V
1
0
1
1
0.120V
0
1
1
1
0.110V
1
1
1
1
0.100V
The constant-current setting for channels 5 and 6 can be set individually for each channel.
(When D3 is 0, channel 5 is set, and when D3 is 1, channel 6 is set.)
The constant-current output value is set by the constant-current reference voltage set with the serial data and the value
of the resistor (referred to as "RF" here) connected to the RF5 or RF6 pin.
The formula below is used to calculated the constant-current output value.
<Constant-current output level> = <current setting reference voltage>/<RF resistor>
No.A0438-25/26
LV8044LP,LV8044LQ
Photosensor Drive Circuit (PI1, PI2, and PI3)
The photosensor drive circuit has open-drain outputs. The output is controlled (set to on or off) by a bit in the serial data
(0 or 1).
Truth Table
Input
ST
D3
Output
D4
D5
Drive circuit
PI1
PI2
PI3
Low
*
*
*
OFF
OFF
OFF
High
0
*
*
OFF
*
*
Standby mode
Off
High
1
*
*
Low
*
*
On
High
*
0
*
*
OFF
*
Off
High
*
1
*
*
Low
*
On
High
*
*
0
*
*
OFF
Off
High
*
*
1
*
*
Low
On
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of October, 2011. Specifications and information herein are subject
to change without notice.
PS No.A0438-26/26