194D www.vishay.com Vishay Sprague Solid Tantalum Chip Capacitors, TANTAMOUNT®, Conformal Coated FEATURES • 8 mm, 12 mm, 16 mm tape and reel packaging available per EIA-481 and reeling per IEC 60286-3, 7" [178 mm] standard • Mounting: Surface mount • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 Note * Lead (Pb)-containing terminations are not RoHS-compliant. Exemptions may apply. PERFORMANCE CHARACTERISTICS www.vishay.com/doc?40088 Operating Temperature: - 55 °C to + 125 °C (above 85 °C, voltage derating is required) Capacitance Range: 0.10 μF to 330 μF Capacitance Tolerance: ± 10 %, ± 20 % standard Voltage Rating: 4 VDC to 50 VDC ORDERING INFORMATION 194D 225 X0 004 A 2 T TYPE CAPACITANCE CAPACITANCE TOLERANCE DC VOLTAGE RATING AT + 85 °C CASE CODE TERMINATION PACKAGING This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. X0 = ± 20 % X9 = ± 10 % X5 = ± 5 % Special order This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating See Ratings and Case Codes table 2 = Gold plated (50 μ inch minimum) standard (RoHS compliant) 8 = 60/40 solder plated 7 = Hot solder dipped T = T/R (full reel) 7" [178 mm] reel standard H = T/R (half reel) 7" [178 mm] B = Bulk Note • Preferred tolerance and reel sizes are in bold. We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. DIMENSIONS in inches [millimeters] W CASE CODE A B C D E F G H W 0.050 ± 0.015 [1.27 ± 0.38] 0.050 ± 0.015 [1.27 ± 0.38] 0.050 ± 0.015 [1.27 ± 0.38] 0.100 ± 0.015 [2.54 ± 0.38] 0.100 ± 0.015 [2.54 ± 0.38] 0.135 ± 0.015 [3.43 ± 0.38] 0.110 ± 0.015 [2.79 ± 0.38] 0.150 ± 0.015 [3.81 ± 0.38] H T1 - P L L 0.100 ± 0.015 [2.54 ± 0.38] 0.150 ± 0.015 [3.81 ± 0.38] 0.200 ± 0.015 [5.08 ± 0.38] 0.150 ± 0.015 [3.81 ± 0.38] 0.200 ± 0.015 [5.08 ± 0.38] 0.220 ± 0.015 [5.59 ± 0.38] 0.265 ± 0.015 [6.73 ± 0.38] 0.285 ± 0.015 [7.24 ± 0.38] Weld and dimple projection identifies anode (+) terminal H 0.050 ± 0.015 [1.27 ± 0.38] 0.050 ± 0.015 [1.27 ± 0.38] 0.050 ± 0.015 [1.27 ± 0.38] 0.050 ± 0.015 [1.27 ± 0.38] 0.050 ± 0.015 [1.27 ± 0.38] 0.070 ± 0.015 [1.78 ± 0.38] 0.110 ± 0.015 [2.79 ± 0.38] 0.110 ± 0.015 [2.79 ± 0.38] P T2 max. P 0.030 ± 0.005 [0.76 ± 0.13] 0.030 ± 0.005 [0.76 ± 0.13] 0.030 ± 0.005 [0.76 ± 0.13] 0.030 ± 0.005 [0.76 ± 0.13] 0.030 ± 0.005 [0.76 ± 0.13] 0.030 ± 0.005 [0.76 ± 0.13] 0.050 ± 0.005 [1.27 ± 0.13] 0.050 ± 0.005 [1.27 ± 0.13] T1 0.005 [0.13] 0.005 [0.13] 0.005 [0.13] 0.005 [0.13] 0.005 [0.13] 0.005 [0.13] 0.005 [0.13] 0.005 [0.13] T2 MAX. 0.015 [0.38] 0.015 [0.38] 0.015 [0.38] 0.015 [0.38] 0.015 [0.38] 0.015 [0.38] 0.015 [0.38] 0.015 [0.38] Note • When solder coated terminations are required, add 0.015" [0.381 mm] to termination dimension tolerances Revision: 08-Feb-13 Document Number: 40000 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 194D www.vishay.com Vishay Sprague RATINGS AND CASE CODES μF 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 120 150 330 4V A A/B B B/C C/D D/E E/F F F/G F/G H H H H 6V A A/B A/B A/B/C C/D D/E E/F F F/G F/G G/H H H H H 10 V A A/B A/B A/B/C B/C/D D/E C/E/F E/F F/G F/G G/H H G/H H 15 V A A/B A/B A/B/C C/D B/D/E E/F E/F F/G F/G F/G/H G/H H H 20 V 25 V A A/B A/B B/C C/D D/E E/F F E/F/G F/G G/H H A A/B B A/B/C D E F F F/G F/G H G/H H 35 V A A A A/B B C D E F F F/G G/H G/H H 50 V A A B B C D E F F G H H STANDARD RATINGS CAPACITANCE (μF) 2.2 3.3 3.3 4.7 6.8 6.8 10 10 15 15 22 22 33 47 47 68 68 100 120 150 330 MAX. DCL AT + 25 °C (μA) 4 VDC AT + 85 °C, SURGE = 5 V; 2.7 VDC AT + 125 °C, SURGE = 3.4 V A 194D225(1)004A(2)(3) 0.5 A 194D335(1)004A(2)(3) 0.5 B 194D335(1)004B(2)(3) 0.5 B 194D475(1)004B(2)(3) 0.5 B 194D685(1)004B(2)(3) 0.5 C 194D685(1)004C(2)(3) 0.5 C 194D106(1)004C(2)(3) 0.5 D 194D106(1)004D(2)(3) 0.5 D 194D156(1)004D(2)(3) 0.6 E 194D156(1)004E(2)(3) 0.6 E 194D226(1)004E(2)(3) 0.9 F 194D226(1)004F(2)(3) 0.9 F 194D336(1)004F(2)(3) 1.3 F 194D476(1)004F(2)(3) 1.9 G 194D476(1)004G(2)(3) 1.9 F 194D686(1)004F(2)(3) 2.7 G 194D686(1)004G(2)(3) 2.7 H 194D107(1)004H(2)(3) 4.0 H 194D127(1)004H(2)(3) 4.8 H 194D157(1)004H(2)(3) 6.0 H 194D337(1)004H(2)(3) 13.2 CASE CODE PART NUMBER MAX. DF AT + 25 °C 120 Hz (%) 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 10 Notes • Part number definitions: (1) Tolerance: For 10 % tolerance, specify “X9”; for 20 % tolerance, change to “X0”, for 5 % tolerance specify “X5” (special order) (2) Termination: For gold plated specify “2”, for solder plated 60/40 specify “8”, for hot solder dipped specify “7” (3) Packaging code: For 7" reels specify “T”, for half of 7" reels specify “H”, for bulk specify “B” (1) 5 % tolerance is not available for the 0.33 μF/50 V design Revision: 08-Feb-13 Document Number: 40000 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 194D www.vishay.com Vishay Sprague STANDARD RATINGS CAPACITANCE (μF) 1.5 2.2 2.2 3.3 3.3 4.7 4.7 4.7 6.8 6.8 10 10 15 15 22 33 33 47 47 68 68 100 120 150 330 1.0 1.5 1.5 2.2 2.2 3.3 3.3 3.3 4.7 4.7 4.7 6.8 6.8 10 10 10 15 15 22 22 CASE CODE PART NUMBER MAX. DCL AT + 25 °C (μA) 6 VDC AT + 85 °C, SURGE = 8 V; 4 VDC AT + 125 °C, SURGE = 5 V A 194D155(1)006A(2)(3) 0.5 A 194D225(1)006A(2)(3) 0.5 B 194D225(1)006B(2)(3) 0.5 A 194D335(1)006A(2)(3) 0.5 B 194D335(1)006B(2)(3) 0.5 A 194D475(1)006A(2)(3) 0.5 B 194D475(1)006B(2)(3) 0.5 C 194D475(1)006C(2)(3) 0.5 C 194D685(1)006C(2)(3) 0.5 D 194D685(1)006D(2)(3) 0.5 D 194D106(1)006D(2)(3) 0.6 E 194D106(1)006E(2)(3) 0.6 E 194D156(1)006E(2)(3) 1.0 F 194D156(1)006F(2)(3) 1.0 F 194D226(1)006F(2)(3) 1.4 F 194D336(1)006F(2)(3) 2.1 G 194D336(1)006G(2)(3) 2.1 F 194D476(1)006F(2)(3) 3.0 G 194D476(1)006G(2)(3) 3.0 G 194D686(1)006G(2)(3) 4.3 H 194D686(1)006H(2)(3) 4.3 H 194D107(1)006H(2)(3) 6.0 H 194D127(1)006H(2)(3) 7.2 H 194D157(1)006H(2)(3) 9.0 H 194D337(1)006H(2)(3) 20.0 10 VDC AT + 85 °C, SURGE = 13 V; 7 VDC AT + 125 °C, SURGE = 9 V A 194D105(1)010A(2)(3) 0.5 A 194D155(1)010A(2)(3) 0.5 B 194D155(1)010B(2)(3) 0.5 A 194D225(1)010A(2)(3) 0.5 B 194D225(1)010B(2)(3) 0.5 A 194D335(1)010A(2)(3) 0.5 B 194D335(1)010B(2)(3) 0.5 C 194D335(1)010C(2)(3) 0.5 B 194D475(1)010B(2)(3) 0.5 C 194D475(1)010C(2)(3) 0.5 D 194D475(1)010D(2)(3) 0.5 D 194D685(1)010D(2)(3) 0.7 E 194D685(1)010E(2)(3) 0.7 C 194D106(1)010C(2)(3) 1.0 E 194D106(1)010E(2)(3) 1.0 F 194D106(1)010F(2)(3) 1.0 E 194D156(1)010E(2)(3) 1.5 F 194D156(1)010F(2)(3) 1.5 F 194D226(1)010F(2)(3) 2.2 G 194D226(1)010G(2)(3) 2.2 MAX. DF AT + 25 °C 120 Hz (%) 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 10 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Notes • Part number definitions: (1) Tolerance: For 10 % tolerance, specify “X9”; for 20 % tolerance, change to “X0”, for 5 % tolerance specify “X5” (special order) (2) Termination: For gold plated specify “2”, for solder plated 60/40 specify “8”, for hot solder dipped specify “7” (3) Packaging code: For 7" reels specify “T”, for half of 7" reels specify “H”, for bulk specify “B” (1) 5 % tolerance is not available for the 0.33 μF/50 V design Revision: 08-Feb-13 Document Number: 40000 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 194D www.vishay.com Vishay Sprague STANDARD RATINGS CAPACITANCE (μF) 33 33 47 47 68 100 100 120 0.68 1.0 1.0 1.5 1.5 2.2 2.2 2.2 3.3 3.3 4.7 4.7 4.7 6.8 6.8 10 10 15 15 22 22 33 33 33 47 47 68 100 0.47 0.68 0.68 1.0 1.0 1.5 1.5 2.2 2.2 3.3 3.3 CASE CODE PART NUMBER MAX. DCL AT + 25 °C (μA) 10 VDC AT + 85 °C, SURGE = 13 V; 7 VDC AT + 125 °C, SURGE = 9 V F 194D336(1)010F(2)(3) 3.3 G 194D336(1)010G(2)(3) 3.3 G 194D476(1)010G(2)(3) 4.7 H 194D476(1)010H(2)(3) 4.7 H 194D686(1)010H(2)(3) 6.8 G 194D107(1)010G(2)(3) 10.0 H 194D107(1)010H(2)(3) 10.0 H 194D127(1)010H(2)(3) 12.0 15 VDC AT + 85 °C, SURGE = 20 V; 10 VDC AT + 125 °C, SURGE = 12 V A 194D684(1)015A(2)(3) 0.5 A 194D105(1)015A(2)(3) 0.5 B 194D105(1)015B(2)(3) 0.5 A 194D155(1)015A(2)(3) 0.5 B 194D155(1)015B(2)(3) 0.5 A 194D225(1)015A(2)(3) 0.5 B 194D225(1)015B(2)(3) 0.5 C 194D225(1)015C(2)(3) 0.5 C 194D335(1)015C(2)(3) 0.5 D 194D335(1)015D(2)(3) 0.5 B 194D475(1)015B(2)(3) 0.7 D 194D475(1)015D(2)(3) 0.7 E 194D475(1)015E(2)(3) 0.7 E 194D685(1)015E(2)(3) 1.1 F 194D685(1)015F(2)(3) 1.1 E 194D106(1)015E(2)(3) 1.6 F 194D106(1)015F(2)(3) 1.6 F 194D156(1)015F(2)(3) 2.4 G 194D156(1)015G(2)(3) 2.4 F 194D226(1)015F(2)(3) 3.5 G 194D226(1)015G(2)(3) 3.5 F 194D336(1)015F(2)(3) 5.3 G 194D336(1)015G(2)(3) 5.3 H 194D336(1)015H(2)(3) 5.3 G 194D476(1)015G(2)(3) 10.0 H 194D476(1)015H(2)(3) 7.0 H 194D686(1)015H(2)(3) 10.0 H 194D107(1)015H(2)(3) 15.0 20 VDC AT + 85 °C, SURGE = 26 V; 13 VDC AT + 125 °C, SURGE = 16 V A 194D474(1)020A(2)(3) 0.5 A 194D684(1)020A(2)(3) 0.5 B 194D684(1)020B(2)(3) 0.5 A 194D105(1)020A(2)(3) 0.5 B 194D105(1)020B(2)(3) 0.5 B 194D155(1)020B(2)(3) 0.5 C 194D155(1)020C(2)(3) 0.5 C 194D225(1)020C(2)(3) 0.5 D 194D225(1)020D(2)(3) 0.5 D 194D335(1)020D(2)(3) 0.7 E 194D335(1)020E(2)(3) 0.7 MAX. DF AT + 25 °C 120 Hz (%) 6 6 6 6 6 10 8 8 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 6 6 10 4 4 4 4 4 6 6 6 6 6 6 Notes • Part number definitions: (1) Tolerance: For 10 % tolerance, specify “X9”; for 20 % tolerance, change to “X0”, for 5 % tolerance specify “X5” (special order) (2) Termination: For gold plated specify “2”, for solder plated 60/40 specify “8”, for hot solder dipped specify “7” (3) Packaging code: For 7" reels specify “T”, for half of 7" reels specify “H”, for bulk specify “B” (1) 5 % tolerance is not available for the 0.33 μF/50 V design Revision: 08-Feb-13 Document Number: 40000 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 194D www.vishay.com Vishay Sprague STANDARD RATINGS CAPACITANCE (μF) 4.7 4.7 6.8 10 10 10 15 15 22 22 33 0.33 0.47 0.47 0.68 1.0 1.0 1.0 1.5 2.2 3.3 4.7 6.8 6.8 10 10 15 22 22 33 0.10 0.15 0.22 0.33 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 4.7 6.8 6.8 10 10 15 MAX. DCL AT + 25 °C (μA) 20 VDC AT + 85 °C, SURGE = 26 V; 13 VDC AT + 125 °C, SURGE = 16 V E 194D475(1)020E(2)(3) 0.9 F 194D475(1)020F(2)(3) 0.9 F 194D685(1)020F(2)(3) 1.4 E 194D106(1)020E(2)(3) 2.0 F 194D106(1)020F(2)(3) 2.0 G 194D106(1)020G(2)(3) 2.0 F 194D156(1)020F(2)(3) 3.0 G 194D156(1)020G(2)(3) 3.0 G 194D226(1)020G(2)(3) 4.0 H 194D226(1)020H(2)(3) 4.4 H 194D336(1)020H(2)(3) 6.6 25 VDC AT + 85 °C, SURGE = 32 V; 17 VDC AT + 125 °C, SURGE = 20 V A 194D334(1)025A(2)(3) 0.5 A 194D474(1)025A(2)(3) 0.5 B 194D474(1)025B(2)(3) 0.5 B 194D684(1)025B(2)(3) 0.5 A 194D105(1)025A(2)(3) 0.5 B 194D105(1)025B(2)(3) 0.5 C 194D105(1)025C(2)(3) 0.5 D 194D155(1)025D(2)(3) 0.5 E 194D225(1)025E(2)(3) 0.6 F 194D335(1)025F(2)(3) 0.8 F 194D475(1)025F(2)(3) 1.2 F 194D685(1)025F(2)(3) 1.7 G 194D685(1)025G(2)(3) 1.7 F 194D106(1)025F(2)(3) 2.5 G 194D106(1)025G(2)(3) 2.5 H 194D156(1)025H(2)(3) 3.8 G 194D226(1)025G(2)(3) 5.5 H 194D226(1)025H(2)(3) 5.5 H 194D336(1)025H(2)(3) 10.0 35 VDC AT + 85 °C, SURGE = 46 V; 23 VDC AT + 125 °C, SURGE = 28 V A 194D104(1)035A(2)(3) 0.5 A 194D154(1)035A(2)(3) 0.5 A 194D224(1)035A(2)(3) 0.5 A 194D334(1)035A(2)(3) 0.5 B 194D334(1)035B(2)(3) 0.5 B 194D474(1)035B(2)(3) 0.5 C 194D684(1)035C(2)(3) 0.5 D 194D105(1)035D(2)(3) 0.5 E 194D155(1)035E(2)(3) 0.5 F 194D225(1)035F(2)(3) 0.8 F 194D335(1)035F(2)(3) 1.2 F 194D475(1)035F(2)(3) 1.6 G 194D475(1)035G(2)(3) 1.6 G 194D685(1)035G(2)(3) 2.4 H 194D685(1)035H(2)(3) 2.4 G 194D106(1)035G(2)(3) 3.5 H 194D106(1)035H(2)(3) 3.5 H 194D156(1)035H(2)(3) 5.3 CASE CODE PART NUMBER MAX. DF AT + 25 °C 120 Hz (%) 6 6 6 6 6 6 6 6 8 6 6 4 4 4 4 6 6 4 6 6 6 6 6 6 6 6 6 6 6 8 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 Notes • Part number definitions: (1) Tolerance: For 10 % tolerance, specify “X9”; for 20 % tolerance, change to “X0”, for 5 % tolerance specify “X5” (special order) (2) Termination: For gold plated specify “2”, for solder plated 60/40 specify “8”, for hot solder dipped specify “7” (3) Packaging code: For 7" reels specify “T”, for half of 7" reels specify “H”, for bulk specify “B” (1) 5 % tolerance is not available for the 0.33 μF/50 V design Revision: 08-Feb-13 Document Number: 40000 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 194D www.vishay.com Vishay Sprague STANDARD RATINGS CAPACITANCE (μF) CASE CODE PART NUMBER MAX. DCL AT + 25 °C (μA) MAX. DF AT + 25 °C 120 Hz (%) 50 VDC AT + 85 °C, SURGE = 65 V; 33 VDC AT + 125 °C, SURGE = 38 V 0.10 A 194D104(1)050A(2)(3) 0.5 0.15 A 194D154(1)050A(2)(3) 0.5 4 4 0.22 B 194D224(1)050B(2)(3) 0.5 4 0.33 (1) B 194D334(1)050B(2)(3) 0.5 4 0.47 C 194D474(1)050C(2)(3) 0.5 4 0.68 D 194D684(1)050D(2)(3) 0.5 4 1.0 E 194D105(1)050E(2)(3) 0.5 4 1.5 F 194D155(1)050F(2)(3) 0.8 6 6 2.2 F 194D225(1)050F(2)(3) 1.1 3.3 G 194D335(1)050G(2)(3) 1.7 6 4.7 H 194D475(1)050H(2)(3) 2.4 6 6.8 H 194D685(1)050H(2)(3) 3.4 6 Notes • Part number definitions: (1) Tolerance: For 10 % tolerance, specify “X9”; for 20 % tolerance, change to “X0”, for 5 % tolerance specify “X5” (special order) (2) Termination: For gold plated specify “2”, for solder plated 60/40 specify “8”, for hot solder dipped specify “7” (3) Packaging code: For 7" reels specify “T”, for half of 7" reels specify “H”, for bulk specify “B” (1) 5 % tolerance is not available for the 0.33 μF/50 V design RECOMMENDED VOLTAGE DERATING GUIDELINES (for temperatures below + 85 °C) STANDARD CONDITIONS. FOR EXAMPLE: OUTPUT FILTERS Capacitor Voltage Rating Operating Voltage 4.0 2.5 6.0 3.4 10 6.0 16 10 20 12 25 15 35 24 50 28 SEVERE CONDITIONS. FOR EXAMPLE: INPUT FILTERS Revision: 08-Feb-13 Capacitor Voltage Rating Operating Voltage 4.0 2.5 6.0 3.3 10 5.0 16 8.0 20 10 25 12 35 15 50 24 Document Number: 40000 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 194D www.vishay.com Vishay Sprague POWER DISSIPATION CASE CODE MAXIMUM PERMISSIBLE POWER DISSIPATION AT + 25 °C (W) IN FREE AIR A 0.060 B 0.075 C 0.075 D 0.085 E 0.095 F 0.110 G 0.120 H 0.150 STANDARD PACKAGING QUANTITY CASE CODE QUANTITY (pcs/reel) 7" FULL REEL 7" HALF REEL BULK, PLASTIC TRAY QUANTITY 75 A 2500 1250 B 2500 1250 75 C 2500 1250 75 D 2500 1250 75 E 2500 1250 75 F 1000 500 75 G 600 300 60 H 600 300 50 PRODUCT INFORMATION Conformal Coated Guide Pad Dimensions www.vishay.com/doc?40150 Package Dimensions Moisture Sensitivity www.vishay.com/doc?40135 SELECTOR GUIDES Solid Tantalum Selector Guide www.vishay.com/doc?49053 Solid Tantalum Chip Capacitors www.vishay.com/doc?40091 FAQ Frequently Asked Questions Revision: 08-Feb-13 www.vishay.com/doc?40110 Document Number: 40000 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000