ESD7016, SZESD7016 Low Capacitance ESD Protection USB3.0 The ESD7016 transient voltage suppressor is specifically designed to protect USB3.0 interfaces by integrating two Superspeed pairs, D+, D−, and Vbus lines into a single protection product. Ultra−low capacitance and low ESD clamping voltage make this device an ideal solution for protecting voltage sensitive high speed data lines. The flow−through style package allows for easy PCB layout and matched trace lengths necessary to maintain consistent impedance between high speed differential lines. Features • MARKING DIAGRAM UDFN8 CASE 517CB 6M MG G 1 • Low Capacitance (0.15 pF Typical, I/O to GND) • Protection for the Following IEC Standards: • • http://onsemi.com IEC 61000−4−2 (Level 4) Low ESD Clamping Voltage SZ Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q101 Qualified and PPAP Capable This is a Pb−Free Device 6M = Specific Device Code M = Date Code G = Pb−Free Package (Note: Microdot may be in either location) PIN CONFIGURATION AND SCHEMATIC I/O 1 Typical Applications • USB 3.0 I/O 2 N/C MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Vbus or Ground I/O 3 Rating Symbol Value Unit Operating Junction Temperature Range TJ −55 to +125 °C Storage Temperature Range Tstg −55 to +150 °C I/O 5 Lead Solder Temperature − Maximum (10 Seconds) TL 260 °C I/O 6 ESD ESD ±15 ±15 kV kV IEC 61000−4−2 Contact (ESD) IEC 61000−4−2 Air (ESD) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. I/O 4 N/C ORDERING INFORMATION Device Package Shipping ESD7016MUTAG UDFN8 (Pb−Free) 3000 / Tape & Reel SZESD7016MUTAG UDFN8 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2013 May, 2013 − Rev. 3 1 Publication Order Number: ESD7016/D ESD7016, SZESD7016 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise specified) Parameter Symbol Reverse Working Voltage Conditions VRWM Breakdown Voltage Min Typ Max Unit 5.0 V I/O Pin to GND VBR IT = 1 mA, I/O Pin to GND 5.5 V Reverse Leakage Current IR VRWM = 5 V, I/O Pin to GND 1.0 mA Clamping Voltage (Note 1) VC IPP = 1 A, I/O Pin to GND (8 x 20 ms pulse) 10 V Clamping Voltage (Note 2) VC IEC61000−4−2, ±8 kV Contact Clamping Voltage TLP (Note 3) See Figures 6 through 9 VC IPP = ±8 A IPP = ±16 A 14.6 20.5 Junction Capacitance CJ VR = 0 V, f = 1 MHz between I/O Pins and GND 0.15 Junction Capacitance Difference DCJ VR = 0 V, f = 1 MHz between I/O Pins and GND 0.03 See Figures 1 and 2 V 0.20 pF pF 1. Surge current waveform per Figure 5. 2. For test procedure see Figures 3 and 4 and application note AND8307/D. 3. ANSI/ESD STM5.5.1 − Electrostatic Discharge Sensitivity Testing using Transmission Line Pulse (TLP) Model. TLP conditions: Z0 = 50 W, tp = 100 ns, tr = 4 ns, averaging window; t1 = 30 ns to t2 = 60 ns. 80 0 70 −10 60 −20 VOLTAGE (V) VOLTAGE (V) 90 50 40 30 20 −30 −40 −50 −60 −70 10 −80 0 −90 −10 −20 0 20 40 60 80 100 120 −100 −20 140 0 20 40 60 80 100 120 TIME (ns) TIME (ns) Figure 1. IEC61000−4−2 +8 KV Contact Clamping Voltage Figure 2. IEC61000−4−2 −8 KV Contact Clamping Voltage http://onsemi.com 2 140 ESD7016, SZESD7016 IEC61000−4−2 Waveform IEC 61000−4−2 Spec. Ipeak Level Test Voltage (kV) First Peak Current (A) Current at 30 ns (A) Current at 60 ns (A) 1 2 7.5 4 2 2 4 15 8 4 3 6 22.5 12 6 4 8 30 16 8 100% 90% I @ 30 ns I @ 60 ns 10% tP = 0.7 ns to 1 ns Figure 3. IEC61000−4−2 Spec ESD Gun Oscilloscope TVS 50 W Cable 50 W Figure 4. Diagram of ESD Clamping Voltage Test Setup The following is taken from Application Note AND8308/D − Interpretation of Datasheet Parameters for ESD Devices. systems such as cell phones or laptop computers it is not clearly defined in the spec how to specify a clamping voltage at the device level. ON Semiconductor has developed a way to examine the entire voltage waveform across the ESD protection diode over the time domain of an ESD pulse in the form of an oscilloscope screenshot, which can be found on the datasheets for all ESD protection diodes. For more information on how ON Semiconductor creates these screenshots and how to interpret them please refer to AND8307/D and AND8308/D. ESD Voltage Clamping For sensitive circuit elements it is important to limit the voltage that an IC will be exposed to during an ESD event to as low a voltage as possible. The ESD clamping voltage is the voltage drop across the ESD protection diode during an ESD event per the IEC61000−4−2 waveform. Since the IEC61000−4−2 was written as a pass/fail spec for larger % OF PEAK PULSE CURRENT 100 PEAK VALUE IRSM @ 8 ms tr 90 PULSE WIDTH (tP) IS DEFINED AS THAT POINT WHERE THE PEAK CURRENT DECAY = 8 ms 80 70 60 HALF VALUE IRSM/2 @ 20 ms 50 40 30 tP 20 10 0 0 20 40 t, TIME (ms) 60 Figure 5. 8 X 20 ms Pulse Waveform http://onsemi.com 3 80 22 −22 20 −20 18 −18 16 −16 CURRENT (A) CURRENT (A) ESD7016, SZESD7016 14 12 10 8 −14 −12 −10 −8 6 −6 4 −4 2 −2 0 0 2 4 6 8 0 10 12 14 16 18 20 22 24 26 0 2 4 6 8 10 12 14 16 18 20 22 24 26 VOLTAGE (V) VOLTAGE (V) Figure 6. Positive TLP I−V Curve Figure 7. Negative TLP I−V Curve Transmission Line Pulse (TLP) Measurement L Transmission Line Pulse (TLP) provides current versus voltage (I−V) curves in which each data point is obtained from a 100 ns long rectangular pulse from a charged transmission line. A simplified schematic of a typical TLP system is shown in Figure 8. TLP I−V curves of ESD protection devices accurately demonstrate the product’s ESD capability because the 10s of amps current levels and under 100 ns time scale match those of an ESD event. This is illustrated in Figure 9 where an 8 kV IEC 61000−4−2 current waveform is compared with TLP current pulses at 8 A and 16 A. A TLP I−V curve shows the voltage at which the device turns on as well as how well the device clamps voltage over a range of current levels. S Attenuator ÷ 50 W Coax Cable 10 MW IM 50 W Coax Cable VM DUT VC Oscilloscope Figure 8. Simplified Schematic of a Typical TLP System Figure 9. Comparison Between 8 kV IEC 61000−4−2 and 8 A and 16 A TLP Waveforms http://onsemi.com 4 ESD7016, SZESD7016 Without ESD7016 With ESD7016 Figure 10. USB3.0 Eye Diagram with and without ESD7016, 5 Gb/s S21 INSERTION LOSS (dB) 4 2 ESD7016 IO−GND 0 −2 −4 −6 −8 −10 1.E+06 1.E+07 1.E+08 1.E+09 FREQUENCY (Hz) Figure 11. ESD7016 Insertion Loss http://onsemi.com 5 1.E+10 ESD7016, SZESD7016 I/O Pin 1 I/O Pin 2 I/O Pin 4 I/O Pin 5 I/O Pin 7 I/O Pin 8 Pinout Option 1: 2 Ground connections between high speed pairs to minimize crosstalk. USB 3.0 Type A Connector StdA_SSTX+ Vbus StdA_SSTX− D− GND Pin 3 GND_DRAIN GND Pin 6 D+ StdA_SSRX+ = GND StdA_SSRX− I/O Pin 1 I/O Pin 2 VBUS Pin 3 I/O Pin 4 I/O Pin 5 I/O Pin 7 I/O Pin 8 Pinout Option 2: Single ground connection and Vbus protection for fully integrated solution. USB 3.0 Type A Connector StdA_SSTX+ Vbus StdA_SSTX− Vbus D− GND_DRAIN GND Pin 6 D+ StdA_SSRX+ = GND StdA_SSRX− Figure 12. USB3.0 Type A Connector Layout Diagrams http://onsemi.com 6 ESD7016, SZESD7016 USB 3.0 Micro B Connector Vbus ESD9X D− D+ ID GND ESD7016 N/C ID N/C MicB_SSTX− MicB_SSTX+ GND_DRAIN MicB_SSRX− MicB_SSRX+ Figure 13. USB3.0 Micro B Connector Layout Diagram http://onsemi.com 7 ESD7016, SZESD7016 PACKAGE DIMENSIONS UDFN8, 3.3x1.0, 0.4P CASE 517CB ISSUE O PIN ONE REFERENCE 2X 0.10 C ÉÉ ÉÉ 0.10 C 2X 0.05 C DETAIL A ALTERNATE CONSTRUCTIONS EXPOSED Cu A DETAIL B DIM A A1 A3 b D D2 E E2 e G2 L L1 L2 ÉÉÉ ÉÉÉ ÇÇÇ TOP VIEW (A3) MOLD CMPD DETAIL B A1 SIDE VIEW 8X DETAIL A 1 e/2 e 7X 2X G2 C ALTERNATE CONSTRUCTION SEATING PLANE b 8 L2 E2 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. L1 E 0.05 C 2X L L A B D 0.10 M C A B 0.05 M C MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 3.30 BSC 0.25 0.45 1.00 BSC 0.45 0.55 0.40 BSC 1.19 BSC 0.20 0.30 −−− 0.15 0.30 0.40 RECOMMENDED SOLDERING FOOTPRINT* NOTE 3 1.66 2X L 0.50 2X 0.65 D2 BOTTOM VIEW 0.10 M C A B 0.05 M C 1.20 0.50 8X 0.25 7X 0.40 PITCH 0.40 DIMENSION: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative ESD7016/D