TI TSU6111RSVR

TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
SP2T Switch with Impedance Detection
Micro-USB Switch to Support USB, UART
Check for Samples: TSU6111
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
VBUS_IN
QFN-RSV PIN-OUT
16
15
14
13
DM_HOST
1
12
GND
DP_HOST
2
11
SDA
TxD
3
10
SCL
RxD
4
9
INTB
5
6
7
8
VDDIO
•
The switch is controlled by automatic detection logic
or through I2C manually. JIG and BOOT pins are
used when a USB, UART JIG cable is used to test in
the development and manufacturing. TSU6111 has
open-drain JIG output (active low).
DM_CON
•
Power for this device is supplied through VBAT of the
system or through VBUS_IN when attached.
JIG
•
The TSU6111 is a differential high performance
automated SP2T switch with impedance detection.
The switch features impedance detection which
supports the detection of various accessories that are
attached through DP, DM and ID. The charger
detection satisfies USB charger specification v1.1.
VBUS_IN has 28V tolerance to avoid external
protection.
DP_CON
•
DESCRIPTION
BOOT
•
Cell Phones and Smart Phones
Tablet PCs
Digital Cameras and Camcorders
GPS Navigation Systems
Micro USB interface with USB/UART
ID_CON
•
Dual SP2T
– USB & UART Path support USB 2.0 High
Speed
Smart Detection
– Plug-in/Un-plug Detection
– USB Charger Detection
– Impedance Detection
– Detection is Compatible to CEA-936A
(4-Wire Protocol, UART interface)
Charger Detection
– USB BCDv1.1 Compliant
– VBUS Detection
– Data Contact Detection
– Primary and Secondary Detection
Compatible Accessories
– USB Cable
– UART Cable
– USB Charger BCDv1.1
Additional Features
– I2C Interface with Host Processor
– Support Control Signals Used In
Manufacturing (JIG, BOOT)
– Interrupt for Attach and Detach Accessory
Max Voltage
– 28v VBUS rating
ESD Performance Tested Per JESD 22
– 2000-V Human-Body Model
(A114-B, Class II)
– 1000-V Charged-Device Model (C101)
ESD Performance DP/DM/ID/VBUS to GND
– ±8kV Contact Discharge (IEC 61000-4-2)
Surge Protection on VBUS/DP/DM
– USB Connector Pins Without External
Components
VBAT
1
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011, Texas Instruments Incorporated
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION (1)
PACKAGE (2)
TA
–40°C to 85°C
(1)
(2)
uQFN 0.4-mm pitch – RSV
ORDERABLE PART NUMBER
TOP-SIDE MARKING
TSU6111RSVR
ZTC
Tape and Reel
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
BLOCK DIAGRAM
Power
Supply
TSU6111
VBAT
VDDIO
Supply
Detect
VBUS_IN
USB HS
DM_HT
DM_CON
DP_HT
DP_CON
Switch
Matrix
UART
or
USB HS
Micro
USB
ID_CON
GND
RxD
TxD
INTB
SDA
Processor
SCL
Logic
& I2C
DP/DM
Comparator
JIG
BOOT
ADC
SWITCH MATRIX
USB
DM_HT
TSU6111 SWITCH
MATRIX
VBUS
DP_HT
DM_CON
Micro
USB
UART
TxD
DP_CON
RxD
ID_CON
2
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
PIN FUNCTIONS
PIN
NO.
NAME
I/O
DESCRIPTION
1
DM_HOST
I/O
USB DM connected to host
2
DP_HOST
I/O
USB DP connected to host
3
TxD
I/O
UART Tx
4
RxD
I/O
UART Rx
5
VBAT
I
Connected to battery
6
BOOT
O
BOOT mode out (push-pull)
7
JIG
O
JIG detection (TSU6111 open-drain active low)
8
VDDIO
O
I/O voltage reference
9
INTB
O
Interrupt to host (push-pull)
10
SCL
I
I2C clock
11
SDA
I/O
I2C data
12
GND
13
VBUS_IN
I
14
DM_CON
I/O
USB DM connected to USB receptacle
15
DP_CON
I/O
USB DP connected to USB receptacle
16
ID_CON
I/O
USB ID connected to USB receptacle
Ground
VBUS connected to USB receptacle
SUMMARY OF TYPICAL CHARACTERISTICS
TA = 25°C
USB Path
Number of channels
2
8Ω
ON-state resistance (ron)
0.5 Ω
ON-state resistance match (Δron)
0.5 Ω
ON-state resistance flatness (ron(flat))
95 µs/ 3.5 µs
Turn-on/turn-off time (tON/tOFF)
Bandwidth (BW)
920 MHz
OFF isolation (OISO)
–26 dB at 250 MHz
Crosstalk (XTALK)
–32 dB at 250 MHz
Leakage current (IIO(ON))
50 nA
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
3
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
ABSOLUTE MAXIMUM RATINGS (1) (2)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
VBUS
Supply voltage from USB connector
–0.5
28
VBAT
Supply voltage from battery
–0.5
6.0
VDDIO
Logic supply voltage
–0.5
4.6
V
VUSBIO
Switch I/O voltage range
USB Switch
–0.5
VBAT+0.5
V
VUARTIO
Switch I/O voltage range
UART Switch
–0.5
VBAT+0.5
IK
Analog port diode current
–50
50
mA
ISW-DC
ON-state continuous switch current
–60
60
mA
ISWPEAK
ON-state peak switch current
–150
150
mA
IIK
Digital logic input clamp current
–50
mA
ILOGIC_O
Continuous current through logic output
50
mA
IGND
Continuous current through GND
100
mA
Tstg
Storage temperature range
150
°C
(1)
(2)
VL < 0
–50
–65
V
V
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum.
THERMAL IMPEDANCE RATINGS
UNIT
θJA
4
Package thermal impedance
RSV package
Submit Documentation Feedback
184
°C/W
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
ELECTRICAL SPECIFICATION
over operating free-air temperature range (unless otherwise noted)
PARAMETERS
TEST CONDITIONS
MIN
MAX
UNIT
DIGITAL SIGNALS – I2C INTERFACE (SCL and SDA)
VDDIO
Logic and I/O supply voltage
1.65
3.6
V
VIH
High-level input voltage
VDDIO × 0.7
VDDIO
V
VIL
Low-level input voltage
0
VDDIO × 0.3
V
VOH
High-level output voltage
IOH = –3 mA
VOL
Low-level output voltage
IOL = 3 mA
fSCL
SCL frequency
VDDIO × 0.7
V
0.4
V
400
kHz
0.5
V
JIG OUTPUT (TSU6111 – OPEN-DRAIN OUTPUT, ACTIVE LOW)
VOL
Low-level output voltage
IOL = 10 mA, VBAT = 3.0 V
INTB AND BOOT (PUSH-PULL OUTPUT)
VOH
High-level output voltage
IOH = –4 mA , VDDIO = 1.65 V
VOL
Low-level output voltage
IOL = 4 mA , VDDIO = 1.65 V
1.16
V
0.33
V
TOTAL SWITCH CURRENT CONSUMPTION
IDD(Standby)
VBAT Standby current consumption
VBUS_IN = 0 V, Idle state
30
µA
IDD(Operating)
VBAT Operating current
consumption
VBUS_IN = 0 V, USB switches ON
75
µA
ELECTRICAL CHARACTERISTICS (1)
VBAT = 3 V to 4.4 V, VDDIO = 2.8 V, TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
0
VBAT
V
8
15
Ω
VI = 0.4 V, IO = –2 mA, VBAT = 3.0 V
0.5
2
Ω
VI = 0 V to 3.6 V, IO = –2 mA,
VBAT = 3.0 V
0.5
2
Ω
ANALOG SWITCH
VUSBIO
Analog signal range
DM_HT, DP_HT,
DM_CON, DP_CON
VI = 0 V to 3.6 V, IO = –2 mA,
VBAT = 3.0 V
rON
ON-state resistance
ΔrON
ON-state resistance
DM_HT, DP_HT,
match between channels DM_CON, DP_CON
rON(flat)
ON-state resistance
flatness
IIO(OFF)
VI or VO OFF leakage current
VI = 0.3 V, VO = 2.7 V or
VI = 2.7 V, VO = 0.3 V,
VBAT = 4.4 V, Switch OFF
45
200
nA
IIO(ON)
VO ON leakage current
VI = OPEN, VO = 0.3 V or 2.7 V,
VBAT = 4.4 V, Switch ON
50
200
nA
DM_HT, DP_HT,
DM_CON, DP_CON
DYNAMIC
tON
Turn-ON time
From receipt of I2C
ACK bit
VI or VO = VBAT, RL = 50 Ω, CL = 35 pF
95
µs
tOFF
Turn-OFF time
From receipt of I2C
ACK bit
VI or VO = VBAT, RL = 50 Ω, CL = 35 pF
3.5
µs
CI(OFF)
VI OFF capacitance
DC bias = 0 V or 3.6 V, f = 10 MHz,
Switch OFF
4
pF
CO(OFF)
VO OFF capacitance
DC bias = 0 V or 3.6 V, f = 10 MHz,
Switch OFF
7
pF
CI(ON),
CO(ON)
VI, VO ON capacitance
DC bias = 0 V or 3.6 V, f = 10 MHz,
Switch ON
9
pF
BW
Bandwidth
RL = 50 Ω, Switch ON
920
MHz
OISO
OFF Isolation
f = 240 MHz, RL = 50 Ω, Switch OFF
–26
dB
XTALK
Crosstalk
f = 240 MHz, RL = 50 Ω
–32
dB
(1)
VO is equal to the asserted voltage on DP_CON and DM_CON pins. VI is equal to the asserted voltage on DP_HT and DM_HT pins. IO
is equal to the current on the DP_CON and DM_CON pins. II is equal to the current on the DP_HT and DM_HT pins.
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
5
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
GENERAL OPERATION
The TSU6111 will automatically detect accessories plugged into the phone via the mini/micro USB 5 pin
connector. The type of accessory detected will be stored in I2C registers within the TSU6111 for retrieval by the
host. The TSU6111 has a network of switches that can be automatically opened and closed base on the
accessory detection. See the Table 1 for details of which switches are open during each mode of operation. For
flexibility, the TSU6111 also offers a manual switching mode allowing the host processor to decide which
switches should be opened and closed and execute the settings through the I2C interface.
STANDBY MODE
Standby mode is the default mode upon power up and occurs when no accessory has been detected. During this
mode, the VBUS and ID lines are continually monitored through comparators to determine when an accessory is
inserted. Power consumption is minimal during standby mode.
EYE DIAGRAM USB 2.0 HIGH SPEED
6
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
ACCESSORY ID DETECTION
If VBUS_IN is high and the attachment is not a charger, then determine the impedance on the ID pin. If VBUS_IN is
low and an accessory is attached, then use an ADC for impedance sensing on the ID pin to identify which
accessory is attached.
IMPEDANCE BUCKETS FOR EACH ACCESSORY
In order to implement ID detection, each accessory should contain below ID impedance resistor value which is
5% tolerance accuracy.
Table 1. Accessory ID and Switch States
ACCCESSORY
DETECTED
IMPEDANCE
ON ID
SWITCH STATE
RESISTOR
TOLERANCE
(%)
ADC
VALUE
DP/DM
USB
UART
FACTORY CABLE
JIG
BOOT
OTG
0
—
00000
ON
OFF
OFF
OFF
Send_End Button
2K
10%
00001
OFF
OFF
OFF
OFF
Audio Device Type 3
28.7K
5%
01110
OFF
OFF
OFF
OFF
Reserved Accessory #1
34K
5%
01111
OFF
OFF
OFF
OFF
Reserved Accessory #2
40.2K
5%
10000
OFF
OFF
OFF
OFF
Reserved Accessory #3
49.9K
5%
10001
OFF
OFF
OFF
OFF
Reserved Accessory #4
64.9K
5%
10010
OFF
OFF
OFF
OFF
Audio Device Type 2
80.27K
5%
10011
OFF
ON
OFF
OFF
Phone Powered Device
102K
5%
10100
OFF
ON
OFF
OFF
TTY Converter
121K
5%
10101
OFF
OFF
OFF
OFF
UART Cable
150K
5%
10110
OFF
ON
OFF
OFF
Type 1 Charger
200K
5%
10111
OFF
OFF
OFF
OFF
Factory Mode Cable - Boot Off USB
255K
5%
11000
ON
OFF
ON
OFF
Factory Mode Cable - Boot On USB
301K
5%
11001
ON
OFF
ON
ON
Audio/Video Cable
365K
5%
11010
OFF
OFF
OFF
OFF
Type 2 Charger
442K
5%
11011
OFF
OFF
OFF
OFF
Factory Mode Cable - Boot Off UART
523K
5%
11100
OFF
ON
ON
OFF
Factory Mode Cable - Boot On UART
619K
5%
11101
OFF
ON
ON
ON
Stereo Headset with Remote
1000.07K
10%
11110
OFF
OFF
OFF
OFF
Mono/Stereo Headset
1002K
10%
11110
OFF
OFF
OFF
OFF
No ID
—
—
11111
OFF
OFF
OFF
OFF
USB Standard Downstream Port
—
—
11111
ON
OFF
OFF
OFF
USB Charging Downstream Port
—
—
11111
ON
OFF
OFF
OFF
Dedicated Charging Port
—
—
11111
OFF
OFF
OFF
OFF
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
7
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Power-On Reset
When power (from 0 V) is applied to VBAT, an internal power-on reset holds the TSU6111 in a reset condition
until VBAT has reached VPOR. At that point, the reset condition is released, and the TSU6111 registers and I2C
state machine initialize to their default states.
After the initial power-up phase, VBAT must be lowered to below 0.2 V and then back up to the operating voltage
(VDDIO) for a power-reset cycle.
Software Reset
The TSU6111 has software reset feature.
• Hold low both I2C_SCL and I2C_SDA more than 30ms will reset digital logic of the TSU6111.
After reset digital logic, INTB will keep low until INT_Mask bit of Control register (0x02) is cleared.
Figure 1. Software Reset
8
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Standard I2C Interface Details
The bidirectional I2C bus consists of the serial clock (SCL) and serial data (SDA) lines. Both lines must be
connected to a positive supply via a pull-up resistor when connected to the output stages of a device. Data
transfer may be initiated only when the bus is not busy.
I2C communication with this device is initiated by the master sending a START condition, a high-to-low transition
on the SDA input/output while the SCL input is high (see Figure 2). After the start condition, the device address
byte is sent, MSB first, including the data direction bit (R/W). This device does not respond to the general call
address. After receiving the valid address byte, this device responds with an ACK, a low on the SDA input/output
during the high of the ACK-related clock pulse.
SDA
SCL
S
P
Start Condition
Stop Condition
Figure 2. Definition of Start and Stop Conditions
The data byte follows the address ACK. The R/W bit is kept low for transfer from the master to the slave. The
data byte is followed by an ACK sent from this device. Data are output only if complete bytes are received and
acknowledged. The output data is valid at time (tpv) after the low-to-high transition of SCL, during the clock cycle
for the ACK.
On the I2C bus, only one data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the high pulse of the clock period, as changes in the data line at this time are interpreted as control
commands (START or STOP) (see Figure 3).
SDA
SCL
Data Line
Charge
Figure 3. Bit Transfer
A Stop condition, a low-to-high transition on the SDA input/output while the SCL input is high, is sent by the
master (see Figure 2).
The number of data bytes transferred between the start and the stop conditions from transmitter to receiver is not
limited. Each byte of eight bits is followed by one ACK bit. The transmitter must release the SDA line before the
receiver can send an ACK bit.
A slave receiver that is addressed must generate an ACK after the reception of each byte. The device that
acknowledges has to pull down the SDA line during the ACK clock pulse so that the SDA line is stable low during
the high pulse of the ACK-related clock period (see Figure 4). Setup and hold times must be taken into account.
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
9
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Data Output
by Transmitter
NACK
Data Output
by Receiver
ACK
SCL From
Master
1
2
8
9
Clock Pulse for
Acknowledgment
Start
Condition
Figure 4. Acknowledgment on I2C Bus
Writes
Data is transmitted to the TSU6111 by sending the device slave address and setting the LSB to a logic 0 (see
Figure 5 for device address). The command byte is sent after the address and determines which register
receives the data that follows the command byte. The next byte is written to the specified register on the rising
edge of the ACK clock pulse.
SCL
Slave Address
SDA
ST 0
1
0
0
Start
1
Sub Address
0
1
0
A
0
0
0
0
0
Date Byte
0
1
0
Register Address
(Control Reg)
W/R
Ack. from slave
Auto-Inc.
Date Byte
A D7 D6 D5 D4 D3 D2 D1 D0 A D7 D6 D5 D4 D3 D2 D1 D0 A SP
Ack
from
slave
Data to Control
Register
Ack
from
slave
Data to Control Register Ack Stop
from
slave
Figure 5. Repeated Data Write to a Single Register
Slave Address
SDA
ST
Start
0
1
0
0
1
Sub Address
0
1
0
A
1
W/R
Ack. from slave
Auto-Inc.
0
0
0
1
0
Date Byte
0
Register Address
(Timing Set 1 Reg)
0
Date Byte
A D7 D6 D5 D4 D3 D2 D1 D0 A D7 D6 D5 D4 D3 D2 D1 D0 A
Ack
from
slave
Data to Timing Set 1
Register
Ack
from
slave
Data to Timing Set 2
Register
Figure 6. Burst Data Write to Multiple Registers
10
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Reads
The bus master first must send the TSU6111 slave address with the LSB set to logic 0. The command byte is
sent after the address and determines which register is accessed. After a restart, the device slave address is
sent again but, this time, the LSB is set to logic 1. Data from the register defined by the command byte then is
sent by the TSU6111. Data is clocked into the SDA output shift register on the rising edge of the ACK clock
pulse. See Figure 7.
Slave Address
SDA
ST 0
1
0
0
1
Start
0
Sub Address
1
0
A
0
0
0
W/R
Ack. from slave
Auto-Inc.
0
0
Slave Address
0
1
1
Register Address
(Interrupt 1 Reg)
A RS 0
1
0
0
1
Ack Re-Start
from
slave
Continued
Date Byte
Date Byte
0
1
1
A D7 D6 D5 D4 D3 D2 D1 D0
W/R
Ack. from slave
Data from Interrupt 1 Reg.
Date Byte
A D7 D6 D5 D4 D3 D2 D1 D0 A D7 D6 D5 D4 D3 D2 D1 D0 NA SP
Data from Interrupt 1 Reg.
Ack. from master
Data from Interrupt 1 Reg.
Stop
No Ack. from master (message ends)
Ack. from master
Figure 7. Repeated Data Read from a Single Register – Combined Mode
SCL
Slave Address
SDA
ST 0
1
0
0
1
Start
0
Sub Address
1
0
A
1
0
0
0
0
Slave Address
0
1
1
Register Address
(Interrupt 1 Reg)
W/R
Ack. from slave
Auto-Inc.
A RS 0
Ack Re-Start
from
slave
Date Byte
1
0
0
1
Date Byte
0
1
1
A D7 D6 D5 D4 D3 D2 D1 D0
W/R
Ack. from slave
Data from Interrupt 1 Reg.
Continued
Date Byte
A D7 D6 D5 D4 D3 D2 D1 D0 A D7 D6 D5 D4 D3 D2 D1 D0 NA SP
Data from Interrupt 2 Reg.
Ack. from master
Data from Int Mask 1 Reg.
Stop
No Ack. from master (Message ends)
Ack. from master
Figure 8. Burst Data Read from Multiple Registers – Combined Mode
Slave Address
SDA
ST 0
Start
1
0
0
1
Sub Address
0
1
0
A
0
0
W/R
Ack. from slave
Auto-Inc.
0
0
0
0
Slave Address
1
Register Address
(Interrupt 1 Reg)
1
A SP ST 0
Ack
Start
from Stop
slave
Date Byte
1
0
0
1
0
Date Byte
1
1
A D7 D6 D5 D4 D3 D2 D1 D0
W/R
Ack. from slave
Data from Interrupt 1 Reg.
Continued
Date Byte
A D7 D6 D5 D4 D3 D2 D1 D0 A D7 D6 D5 D4 D3 D2 D1 D0 NA SP
Data from Interrupt 1 Reg.
Ack. from master
Data from Interrupt 1 Reg.
Ack. from master
Stop
No Ack. from master (Message ends)
Figure 9. Repeated Data Read from a Single Register – Split Mode
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
11
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
SCL
Slave Address
SDA ST 0
Start
1
0
0
1
Sub Address
0
1
0
A
1
0
W/R
Ack. from slave
Auto-Inc.
0
0
0
0
Slave Address
1
Register Address
(Interrupt 1 Reg)
1
A SP ST 0
Ack
Start
from Stop
slave
Date Byte
1
0
0
1
0
Date Byte
1
1
A D7 D6 D5 D4 D3 D2 D1 D0
W/R
Ack. from slave
Data from Interrupt 1 Reg.
Continued
Date Byte
A D7 D6 D5 D4 D3 D2 D1 D0 A D7 D6 D5 D4 D3 D2 D1 D0 NA SP
Data from Interrupt 2 Reg.
Ack. from master
Data from Int Mask 1 Reg.
Ack. from master
Stop
No Ack. from master (Message ends)
Figure 10. Burst Data Read from Multiple Registers – Split Mode
Notes (Applicable to Figure 5–Figure 10):
• SDA is pulled low on Ack. from slave or Ack. from master.
• Register writes always require sub-address write before first data byte.
• Repeated data writes to a single register continue indefinitely until Stop or Re-Start.
• Repeated data reads from a single register continue indefinitely until No Ack. from master.
• Burst data writes start at the specified register address, then advance to the next register address, even to
the read-only registers. For these registers, data write appears to occur, though no data are changed by the
writes. After register 14h is written, writing resumes to register 01h and continues until Stop or Re-Start.
• Burst data reads start at the specified register address, then advance to the next register address. Once
register 14h is read, reading resumes from register 01h and continues until No Ack. from master.
12
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
I2C Register Map (1) (2) (3)
ADD
R
REGISTER
TYPE
RESET
VALUE
01h
Device ID
R
00001010
02h
Control
R/W
xxx11111
03h
Interrupt 1
R
00000000
04h
Interrupt 2
R
x0000000
05h
Interrupt Mask
1
R/W
00000000
06h
Interrupt Mask
2
R/W
x0000000
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
Version ID
OVP_OCP_
DIS
OVP_OCP_
DIS
BIT1
BIT0
Vendor ID
Switch Open
Raw Data
Manual S/W
Wait
INT Mask
OCP_EN
OVP_EN
LKR
LKP
KP
Detach
Attach
OTP_EN
CONNE
CT
Stuck_Key_RC
V
Stuck_Key
ADC_Chang
e
Reserved_Att
ach
A/V_Charg
ing
OCP_EN
OVP_EN
LKR
LKP
KP
Detach
Attach
OTP_EN
CONNE
CT
Stuck_Key_RC
V
Stuck_Key
ADC_Chang
e
Reserved_Att
ach
A/V_Charg
ing
07h
ADC
R
xxx11111
08h
Timing Set 1
R/W
00000000
09h
Timing Set 2
R/W
00000000
0Ah
Device Type
1
R
00000000
USG OTG
DCP
CDP
Carkit
UART
USG
Audio Type2
Audio
Type1
0Bh
Device Type
2
R
00000000
Audio Type3
CHG A/V
TTY
PD
JIG_UART_
OFF
JIG_UART_
ON
JIG_USB_OF
F
JIG_USB_
ON
0Ch
Button 1
R
00000000
7
6
5
4
3
2
1
Send_End
0Dh
Button 2
R
x0000000
Unknown
Error
12
11
10
9
8
13h
Manual S/W 1
R/W
000000xx
D– Switching
14h
Manual S/W 2
R/W
xxxx00xx
BOOT_SW
JIG-ON
(1)
(2)
(3)
ADC Value
Device Wake Up
Switching Wait
Do not use blank register bits.
Write “0” to the blank register bits.
Values read from the blank register bits are not defined and invalid.
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
13
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Slave Address
NAME
SIZE
(BITS)
Slave address
8
BIT 7
0
BIT 6
1
BIT 5
0
DESCRIPTION
BIT 4
BIT 3
0
1
BIT 2
0
BIT 1
1
BIT 0
R/W
Device ID
Address: 01h
Reset Value: 00001010
Type: Read
BIT NO.
NAME
SIZE (BITS)
DESCRIPTION
0-2
Vendor ID
3
A unique number for vendor 010 for Texas Instruments
3-7
Version ID
5
A unique number for chip version 00001b for TSU6111
Control
Address: 02h
Reset Value: xxx11111
Type: Read/Write
BIT NO.
NAME
SIZE (BITS)
0
INT Mask
1
0: Unmask interrupt
1: Mask interrupt
1
Wait
1
0: Wait until host re-sets this bit(WAIT bit) high
1: Wait until Switching timer is expired
2
Manual S/W
1
0: Manual Switching
1: Automatic Switching
3
RAW Data
1
0: Report the status changes on ID to Host
1: Don't report the status changes on ID
4
Switch Open
1
0: Open all Switches
1: Automatic Switching by accessory status
5-7
Reserved
14
DESCRIPTION
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Interrupt 1
Address: 03h
Reset Value: 00000000
Type: Read and Clear
BIT NO.
NAME
SIZE (BITS)
0
Attach
1
DESCRIPTION
1: Accessory is attached
1
Detach
1
1: Accessory is detached
2
KP
1
1: Key press
3
LKP
1
1: Long key press
4
LKR
1
1: Long key release
5
OVP_EN
1
1: OVP enabled
6
OCP_EN
1
1: OCP enabled
7
OVP_OCP_DIS
1
1: OCP_OCP disabled
Interrupt 2
Address: 04h
Reset Value:x0000000
Type: Read and Clear
BIT NO.
NAME
SIZE (BITS)
0
A/V_Charging
1
DESCRIPTION
1: Charger detected when A/V cable is attached
1
Reserved_Attach
1
1: Reserved Device is attached
2
ADC_Change
1
1: ADC value is changed when RAW data is enabled
3
Stuck_Key
1
1: Stuck Key is detected
4
Stuck_Key_RCV
1
1: Stuck Key is recovered
5
Connect
1
1: Switch is connected(closed)
6
OTP_EN
1
1: Over Temperature Protection enabled
7
Reserved
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
15
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Interrupt Mask 1
Address: 05h
Reset Value:00000000
Type: Read/Write
BIT NO.
NAME
SIZE (BITS)
0
Attach
1
DESCRIPTION
0: Unmask Attach Interrupt
1: Mask Attach Interrupt
1
Detach
1
0: Unmask Key press Interrupt
1: Mask Detach Interrupt
2
KP
1
0: Unmask Key press Interrupt
1: Mask Key press Interrupt
3
LKP
1
0: Unmask Long key press Interrupt
1: Mask Long key press Interrupt
4
LKR
1
0: Unmask Long key release Interrupt
1: Mask Long key release Interrupt
5
OVP_EN
1
0: Unmask OVP_EN Interrupt
1: Mask OVP_EN Interrupt
6
OCP_EN
1
0: Unmask OCP_EN Interrupt
1: Mask OCP_EN Interrupt
7
OVP_OCP_DIS
1
0: Unmask OVP_OCP_DIS Interrupt
1: Mask OVP_OCP_DIS Interrupt
Interrupt Mask 2
Address: 06h
Reset Value:x0000000
Type: Read/Write
BIT NO.
NAME
SIZE (BITS)
0
A/V_Charging
1
DESCRIPTION
0: Unmask A/V_Charging Interrupt
1: Mask A/V_Charging Interrupt
1
Reserved_Attach
1
0: Unmask Reserved_Attach Interrupt
1: Mask Reserved_Attach Interrupt
2
ADC_Change
1
0: Unmask ADC_Change Interrupt
1: Mask ADC_Change Interrrupt
3
Stuck_Key
1
0: Unmask Stuck_Key Interrupt
1: Mask Stuck_Key Interrupt
4
Stuck_Key_RCV
1
0: Unmask Stuck_Key_RCV Interrupt
1: Mask Stuck_Key_RCV Interrupt
5
Connect
1
0: Unmask Connect Interrupt
1: Mask Connect Interrupt
6
OTP_EN
1
0: Unmask OTP_EN Interrupt
1: Mask OTP_EN Interrupt
7
Reserved
1
ADC Value
Address: 07h
Reset Value: xxx11111
Type: Read
BIT NO.
NAME
SIZE (BITS)
0-4
AD value
5
53-7
Reserved
3
16
DESCRIPTION
ADC value read from ID
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Timing Set 1
Address: 08h
Reset Value: 00000000
Type: Read/Write
BIT NO.
NAME
SIZE (BITS)
0-3
Device Wake Up
4
4-7
Reserved
4
DESCRIPTION
Device wake up duration
Timing Set 2
Address: 09h
Reset Value: 00000000
Type: Read/Write
BIT NO.
NAME
SIZE (BITS)
0-3
Reserved
4
4-7
Switching wait
4
DESCRIPTION
Waiting duration before switching
Time Table (1)
SETTING VALUE
(1)
DEVICE WAKE UP
SWITCHING WAIT
0000
50 ms
10 ms
0001
100 ms
30 ms
0010
150 ms
50 ms
0011
200 ms
70 ms
0100
300 ms
90 ms
0101
400 ms
110 ms
0110
500 ms
130 ms
0111
600 ms
150 ms
1000
700 ms
170 ms
1001
800 ms
190 ms
1010
900 ms
210 ms
1011
1000 ms
–
1100
–
–
1101
–
–
1110
–
–
1111
–
–
Maximum variation of these timing is ±20%
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
17
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Device Type 1
Address: 0Ah
Reset Value: 00000000
Type: Read
BIT NO.
NAME
SIZE (BITS)
0
Audio type 1
1
DESCRIPTION
Audio device type 1
1
Audio type 2
1
Audio device type 2
2
USB
1
USB host
3
UART
1
UART
4
Carkit
1
Carkit Charger Type 1 or 2
5
CDP
1
Charging Downstream Port (USB Host Hub Charger)
6
DCP
1
Dedicated Charging Port
7
USB OTG
1
USB on-the-go device
Device Type 2
Address: 0Bh
Reset Value:x0000000
Type: Read
BIT NO.
NAME
SIZE (BITS)
0
JIG_USB_ON
1
DESCRIPTION
Factory mode cable
1
JIG_USB_OFF
1
Factory mode cable
2
JIG_UART_ON
1
Factory mode cable
3
JIG_UART_OFF
1
Factory mode cable
4
PPD
1
Phone-powered device
5
TTY
1
TTY converter
6
A/V
1
A/V cable
7
Audio type 3
1
Audio device type 3
Button 1
Address: 0Ch
Reset Value: 00000000
Type: Read and Clear
BIT NO.
NAME
SIZE (BITS)
0
8
1
Send_End key is pressed
1
9
1
Number 1 key is pressed
2
10
1
Number 2 key is pressed
3
11
1
Number 3 key is pressed
4
12
1
Number 4 key is pressed
5
Error
1
Number 5 key is pressed
6
Unknown
1
Number 6 key is pressed
7
Reserved
1
Number 7 key is pressed
18
DESCRIPTION
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
TSU6111
SCDS325 – SEPTEMBER 2011
www.ti.com
Button 2
Address: 0Dh
Reset Value:x0000000
Type: Read and Clear
BIT NO.
NAME
SIZE (BITS)
0
Send_End
1
DESCRIPTION
Number 8 key is pressed
1
1
1
Number 9 key is pressed
2
2
1
Number 10 key is pressed
3
3
1
Number 11 key is pressed
4
4
1
Number 12 key is pressed
5
5
1
Error key is pressed
6
6
1
Unknown key is pressed
7
7
1
Manual S/W 1
Address: 13h
Reset Value: 000000xx
Type: Read/Write
BIT NO.
NAME
SIZE (BITS)
0-1
Unused
2
DESCRIPTION
2-4
D+ Switching
3
000:
001:
010:
011:
Open all switch
D+ is connected to D+ of USB port
Open all switch
D+ is connected to RxD of UART
5-7
D– Switching
3
000:
001:
010:
011:
Open all switch
D– is connected to D– of USB port
Open all switch
D– is connected to TxD of UART
Manual S/W 2
Address: 14h
Reset Value: xxxx00xx
Type: Read/Write
BIT NO.
NAME
SIZE (BITS)
0-1
Unused
2
DESCRIPTION
2
JIG
1
TSU6111:
0: High Impedance
1: GND
3
BOOT
1
0: Low
1: High
4-7
Unused
4
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): TSU6111
19
PACKAGE OPTION ADDENDUM
www.ti.com
27-Oct-2011
PACKAGING INFORMATION
Orderable Device
TSU6111RSVR
Status
(1)
ACTIVE
Package Type Package
Drawing
UQFN
RSV
Pins
Package Qty
16
3000
Eco Plan
(2)
Green (RoHS
& no Sb/Br)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
CU NIPDAU Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Aug-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TSU6111RSVR
Package Package Pins
Type Drawing
UQFN
RSV
16
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
3000
330.0
12.4
Pack Materials-Page 1
2.1
B0
(mm)
K0
(mm)
P1
(mm)
2.9
0.75
4.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Aug-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TSU6111RSVR
UQFN
RSV
16
3000
180.0
180.0
30.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated