ETC HS403

Heatshrink
Adhesive Lined
Description:
This is a flexible, flame retarded heat-shrinkable polyolefin tubing, with
a shrink ratio of 4 : 1 with a thick wall adhesive which melts and flows,
to seal components contained within. Recommended for applications
requiring water-proofing for light cable and wire harnesses and protection
of connector components.
Features :
• • • • • EPA method 3050B
: 1996 other acid digestion
BSEN1122
: 2001 method B other acid digestion
EPA method 3052B
: 1996 other acid digestion
EPA method 3060 and EPA 7196A
: 1992
Atomic absorption spectrometer / inductively coupled plasma atomic emission spectrometer (ICP + AES) UV-VIS
spectrophotometer
Characteristics:
Operating Temperature
: -55°C to +125°C
Minimum Shrink Temperature
: 70°C
Shrink Ratio
: 3:1 and 4:1
Standard Colour
: Black
(Other colours are also available on request)
Applications:
Manufactured by co-extrusion of polyolefin and hot-melt adhesive. Designed to provide both insulation and sealing for the
protected items. Typically uses are the protection of automotive wires, bundled wires and metal tubes against water and
moisture. The high expansion ratio makes it possible to repair most damaged cable jackets without removing connectors.
Technical Data:
Property
Tensile Strength
Ultimate Elongation (%)
Longitudinal Shrinkage (%)
Heat Aging
Ultimate Elongation (%)
Flammability
Dielectric Strength (kv / mm)
Volume Resistivity (ohm-cm)
Copper Stability
Corrosion
Test Method
ASTM D 2671
Typical Data
10.4Mpa
30
UL 224
0 to -10
158°, 168hr
200
VW-1
Pass (outer jacket only)
IEC 243
20
UL224
1 × 1014
ASTM D 2671
Pass
UL224
No corrosion
www.element14.com
www.farnell.com
www.newark.com
www.cpc.co.uk
Page <1>
01/03/13
V1.0
Heatshrink
Adhesive Lined
Part Number Table
Description
Part Number
Heatshrink, Sleeving, 4:1, 4mm
HS400
Heatshrink, Sleeving, 4:1, 6mm
HS401
Heatshrink, Sleeving, 4:1, 8mm
HS402
Heatshrink, Sleeving, 4:1, 12mm
HS403
Heatshrink, Sleeving, 4:1, 16mm
HS404
Heatshrink, Sleeving, 4:1, 20mm
HS405
Heatshrink, Sleeving, 4:1, 24mm
HS406
Heatshrink, Sleeving, 4:1, 32mm
HS407
Heatshrink, Sleeving, 4:1, 52mm
HS408
Heatshrink, Sleeving, 4:1, 4mm, 5m
HS409
Heatshrink, Sleeving, 4:1, 6mm, 5m
HS410
Heatshrink, Sleeving, 4:1, 8mm, 5m
HS411
Heatshrink, Sleeving, 4:1, 12mm, 5m
HS412
Important Notice : This data sheet and its contents (the “Information”) belong to the members of the Premier Farnell group of companies (the “Group”) or are licensed to it. No licence is granted
for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change
without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any
error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any
assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the
Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence.
pro - POWER is the registered trademark of the Group. © Premier Farnell plc 2012.
www.element14.com
www.farnell.com
www.newark.com
www.cpc.co.uk
Page <2>
01/03/13
V1.0