050-115 Media Converter, Dual or Single Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet 5 to 36VDC, M38999 (Signal & Power), M38999 (Fiber Optic) REV 2 DESCRIPTION DATE 6/12/2014 APPROVED MF THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC. 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet 10/100/1000BASE-T to 1000BASE-CWDM The Glenair 050-115 is a 10/100/1000BASE-T to Fiber Media converter that can be configured for 1 or 2 channels and can support conversion to 1000BASECWDM (with the optical loss budget derivative of 1000BASE-LX) protocol. It is designed for harsh environments and incorporates electronics in an environmentally sealed enclosure that incorporates two environmental M38999 connectors. One connector is utilized for power and electrical signal and the second connector is used for the Fiber Optic signals and can be configured to support either single mode or multi-mode fiber applications. The Glenair 050-115 is intended to be used with external passive CWDM to combine send and receive signals on a single fiber. KEY FEATURES/BENEFITS CWDM DFB Lasers for 1000BASE-CWDM InGaAs PIN PD for 1000BASE-CWDM Wide Input Voltage Range: 5-36V Electrical Interface compliant with IEEE 802.3 (10/100/1000BASE-T) Optical Interface derived from IEEE 802.3 (1000BASE-LX10) -20C to +55C Operating Range Magnetics on the electrical signal input side to support 10/100/1000BASE-T operation over 100m Cat 5E IP67 in mated condition M38999 Electrical Signal & Power M38999 Fiber Optic Connector Panel Mount OPTIONAL FEATURES Built In Test Console Port accessible via USB2.0 Built in Test Console Port accessible via UART APPLICATIONS • ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY Harsh Environment Ethernet for Airborne, Tactical and Shipboard applications US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 2 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet Functional Block Diagram SINGLE OR DUAL MEDIA CONVERTER Note: Fiber Optic Channels can be 1000BASE-CWDM according to the wavelengths described in the following table Other Fiber Optic connections are possible – Contact Factory Central Wavelength Table Part Number Development - Wavelength Identifier Central Wavelength (nm) L1 L2 L3 L4 L5 L6 L7 L8 NP 1271 1291 1311 1331 1351 1371 1391 1411 NP = Not Populated (none) Note: This table is used to define the wavelengths for Channel 1 and Channel 2. If Channel 2 is not populated then use “NP” designator. The first 2 letters designate Channel 1 and the second 2 letters designate Channel 2. Channel 1 must always be populated. Example) “L1L2” in the part number development designates central wavelength for: Channel 1 (first 2 letters are L1 = 1271nm) Channel 2 (second 2 letters are L2 =1291nm) ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 3 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet Connectors Insert Arrangement NAME J1 Function Media Converter Mating PLUG Connector Electrical Signal, Status and Built In Test (BIT), & Power D38999 Series III type 15-35 Generic PN D38999/26#D35SN Glenair PN 233-105-G6#15-35SN PIN CONTACTS, 22D SOCKET CONTACTS, 22D D38999 Series III type, 13-4 Generic PN D38999/26#C35SN D38999 Series III MIL-STD-1560 Arrangement 15-35 Fiber Optic Signal J2 Glenair PN 180-091##06-13-4SN PIN CONTACTS SOCKET CONTACTS LX10 CONFIGURATION: LX10 CONFIGURATION Glenair PN 181-001-126S (M29504/5-4238) D38999 Series III MIL-STD-1560 Arrangement 13-4 Note: # = Environmental Class (Material/Finish) ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 4 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet Built In Test (BIT) Functionality - Optional Features This media converter can be offered with built in test functionality accessible through a Console Port via Universal Serial Bus 2.0 (USB 2.0) or via 3.3V CMOS UART (RXD, TXD) or both options can be made available. Functional block diagram for this is shown below. Universal Serial Bus (2.0) BIT • Presents itself as a “Virtual” Communications Port • Compatible with Microsoft Windows, Mac, and Linux OS’s. • On the computer side, open any terminal application (PuTTY, HyperTERM, TeraTERM, etc.) to communicate with the media converter hardware. • Simple “Human Readable” status messages. RS422 UART (TXD) BIT • Useful for when you are interfacing with a embedded microprocessor or micro controller. • Status messages delimitated to allow for easy parsing by embedded software. ALARM STATUS MESSAGES Fiber Side Alarm/Status • Temperature • Transmitter Disable Status • Transmitter Fault Alarm Status • Receiver loss of signal (LOS) or signal Detect (SD) Status Copper Side Status • Link Status (Up or Down) Unit Identification Information • Unit Serial Number • Unit Product Code • Unit Description ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 5 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet TYPICAL CONSOLE PORT WINDOW (PuTTY) ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 6 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet Built In Test (BIT) Functionality – UART This media converter can be offered with built in test functionality accessible via an RS-422 Port. The UART Bit message is a 10 bit message with an update rate of 1 Hz. The message format can be seen below. ALARM STATUS MESSAGES • Fiber Link Status (Up or Down) • Copper Link Status (Up or Down) • Power Supply Status (In Range, or Fault) SERIAL STATUS MESSAGE BIT MAPPING Bit Description 0 Channel 1 Fiber Optic TX Fault (1 = Fault, 0 = No Fault) 1 Channel 1 Ethernet copper Link UP (1 = Link Up, 0 = Link Down) 2 Channel 1 Power Supply Voltage “In Range” Fault (1 = Fault, 0 = No Fault) 3 Not used 4 Channel 2 Fiber Optic TX Fault (1 = Fault, 0 = No Fault) 5 Channel 2 Ethernet copper Link UP (1 = Link Up, 0 = Link Down) 6 Channel 2 Power Supply Voltage “In Range” Fault (1 = Fault, 0 = No Fault) 7 Not Used ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 7 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet Ratings and Specifications ABSOLUTE MAXIMUM RATINGS Parameter Symbol Min Storage Temperature Ts Supply Voltage Typ Max Units -40 +100 °C V cc -0.5 40 V Symbol Min Max Units Operating Temperature T op -20 Supply Voltage V cc 5 Supply Current Notes OPERATING CONDITIONS Parameter Supply Current Power Supply Noise (Peak-Peak) Typ Notes +55 °C 28 36 V Icc 100 150 mA @28VDC PER CHANNEL Icc 500 mA @5VDC, PER CHANNEL V cc 200 mV Max Units dBm ripple OPTICAL CHARACTERISTICS – TRANSMITTER Parameter Symbol Optical Output Power P OUT Optical Wavelength, L2 λ OUT λ OUT Optical Wavelength, L3 λ OUT Optical Wavelength, L4 λ OUT Optical Wavelength, L5 λ OUT Optical Wavelength, L6 λ OUT Optical Wavelength, L7 λ OUT Optical Wavelength, L8 λ OUT Optical Wavelength, L1 Min Typ -8.5 -3 +1 1265 1285 1305 1325 1345 1365 1385 1265 1271 1291 1311 1331 1351 1371 1391 1271 1278 1298 1318 1338 1358 1378 1398 1278 Δλ Spectral Width Notes nm 1 nm Typ Max Units 0 dBm -22 -20 dBm OPTICAL CHARACTERISTICS – RECEIVER Parameter Symbol Optical Sensitivity ( Input Power Range) -12 -7 P IN OP Min. Sensitivity, BER 10 , PRBS 2 -1 P IN MIN -12 P IN MAX -7 Overload, BER 10 , PRBS 2 -1 Min -20 0 Notes PIN PD, LX10 source dBm Optical Wavelength λ IN 1100 1310 1590 nm Note: Use a CWDM Mux module and a CWDM Demux module in the fiber path to avoid saturating fiber optic receiver. ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 8 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet Ratings and Specifications - (continued) ETHERNET COMPLIANCE Parameter Medium Type Distance Gigabit Ethernet, IEEE 802.3ab, 1000BASE-T TIA/EIA-568-B Cat 5E 100m Gigabit Ethernet, IEEE 802.3z, 1000BASE-LX10 (Derived from) Single Mode Fiber 10km Notes Derived from IEEE (9/125µm) COMPLIANCE SPECIFICATIONS CHARACTERISTIC Standard Condition Notes Mechanical Shock MIL-STD-810 40g 6-9rms Mechanical Vibration MIL-STD-810 30g rms ESD MIL-STD-883 Class II MIL-DTL-38999/20 500 Cycles MIL-STD-461F CE101 MIL-STD-461F CE102 MIL-STD-461F CS101 MIL-STD-461F CS106 MIL-STD-461F CS109 MIL-STD-461F CS114 MIL-STD-461F RS101 MIL-STD-461F RS103 MIL-STD-461F RE101 MIL-STD-461F RE102 Mating Durability Conducted Emissions, Power Leads, 30 Hz to 10 kHz Conducted Emissions, Power Leads, 10 kHz to 10 MHz Conducted Susceptibility, Power Leads, 30 Hz to 150KHz Conducted Susceptibility, Transients, Power Leads Conducted Susceptibility, Structure Current, 60 Hz to 100 kHz Conducted Susceptibility, Bulk Cable Injection, 10 kHz to 200 MHz Radiated Susceptibility, Magnetic Field, 30 Hz to 100 kHz Radiated Susceptibility, Electric Field, 2 MHz to 18 GHz Radiated Emissions, Magnetic Field, 30 Hz to 100 kHz Radiated Emissions, Electric Field, 10 kHz to 18 GHz Flame Resistance 2200V HBM EIA364-104 30 seconds Damp Heat EIA364-321 240 hours Eye Safety CDRH and IEC-825 ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY Class 1 Laser Product US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 9 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet Material/Finish Item Housing & Connector Shell Plating Finish: M Plating Finish: MT Plating Finish: NF Contacts Material/Finish Aluminum Nickel Nickel PTFE Olive Drab Cadmium Copper alloy, 50 μInch gold plated D38999 Inserts Thermoplastics Interfacial Seals, 38999 only Elastomer, Fluorosilicon Optical Ferrules & Sleeves Zirconia, Ceramic Insulators Contact retention clip Seal, O-rings Seal Spring PC tail contacts PCB flex Encapsulant Solder type Liquid crystal polymer (LCP) Beryllium copper alloy Fluorosilicone rubber Silicone elastomer Nickel-plated beryllium copper Copper alloy/gold plated FR4 & Polyimide HYSOL EE4215 RoHS compliant Sn95/Sb5 (232°C melting temp) & RoHS compliant Sn96.5/Ag3.0/Cu0.5 (217° melting) ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY Mater ial/Fi nish US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 10 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet OUTLINE DRAWING & PANEL CUT OUT Please contact Glenair for other configurations PANEL CUT OUT – J2 ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 11 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet Input/Output Definition J1 – ELECTRICAL SIGNAL CONNECTOR D38999 Series III 15-35 Mating face for PIN shown 37X SIZE 22D J1 PIN FUNCTION ASSIGNMENTS PIN 1 2 3 NAME NC CH2_MDCCH2_MDD- 4 5 6 7 8 9 CH2_MDD+ CH2_MDBCH2_MDB+ CH1_MDDCH1_MDCCH1_MDB- 10 11 USB_DP USB_DM 12 13 14 15 16 17 18 USB_VBUS NC VIN_RTN VIN_RTN VIN VIN NC DESCRIPTION No Connection NOTES 2 2 PIN 19 20 21 NAME NC CH2_MDC+ PSS 2 2 2 2 2 2 22 23 24 25 26 27 CH1_MDD+ CH1_MDC+ CH1_MDB+ CH1_MDAUSB_VBUS_RTN UART_P USB DATA + USB DATA - 3 3 28 29 NC UART_N USB +5V INPUT No Connection VIN RETURN VIN RETURN +28 VIN +28 VIN No Connection 3 30 31 32 33 34 35 36 37 NC NC CH2_MDANC CH1_MDA+ NC NC CH2_MDA+ DESCRIPTION No Connection Power Supply Status USB RETURN RS422 BIT OUTPUT No Connection RS422 BIT OUTPUT No Connection No Connection NOTES 2 1 2 2 2 2 3 4 4 2 No Connection 2 No Connection No Connection 2 Notes 1. Power Supply Status indicator is high, referenced to 3.3VDC, when power supply is working correctly and low for fault or warning condition. 2. IEEE-802.3 1000BASE-T compliant 3 Built In Test Port, USB2.0 4 Built In Test Port, RS422 UART (RXD, TXD) ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com REV: 2 ∙ 1211 AIR WAY US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 12 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected] 050-115 Media Converter, Single or Dual Channel, Panel Mount 10/100/1000BASE-T to CWDM Fiber Optic Ethernet Input/Output Definition (continued) J2 – FIBER OPTIC CONECTOR D38999 Series III, 13-4 Mating face for PIN shown 4X size 16 PIN CONTACTS J2 PIN FUNCTION ASSIGNMENTS PIN A B C D ©2014 Glenair, Inc. GLENAIR, INC. www.glenair.com NAME CH 1 – Transmitter CH 1 – Receiver CH 2 – Transmitter CH 2 – Receiver REV: 2 ∙ 1211 AIR WAY DESCRIPTION NOTES US Cage Code 06324 ∙ GLENDALE, CA 91201-2497 PAGE 13 of 13 ∙ TEL: 818-247-6000 Printed in USA ∙ FAX: 818-500-9912 E-mail: [email protected]