CVS575S-500.000 True SineWave SAW Based VCSO 5×7.5mm SMD 3.3 Volts Model CVS575S-500 is a 500 MHz voltage-controlled SAW (surface acoustic wave) oscillator (VCSO). SAW crystal technology provides low-noise and low-jitter performance with true sinewave output. Features include -135 dBc/Hz phase noise at 10 kHz offset, 3.3 V input voltage, -20°C to +70°C operating temperature, and 5×7.5 mm SMT package. The oscillator has no sub-harmonic and the second harmonic is typically -14 dBc. Applications include PLL frequency translation, test and measurement, avionics, point-to-point radios, and multi-point radios. Rev: G Date: 17-Feb-2015 Page 1 of 3 CRYSTEK CORPORATION 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CVS575S-500.000 True SineWave SAW Based VCSO 5×7.5mm SMD 3.3 Volts Frequency: Temperature Range: CVS575S-500.000 CVS575SX-500.000 Storage: Input Voltage: Control Voltage Range: Settability At Nominal (25°C): Freq. vs Temperature: Input Current: 500 MHz -20°C to 70°C -40°C to 85°C -45°C to 90°C 3.3V ±0.15V 0V to 3.3V 1.5V ±0.5V +100ppm, -150ppm Typical 20mA Typical, 25mA Max Output: Pullability APR: Linearity: Output Power: Start-up time: 2nd Harmonic: Sub-harmonics: Modulation BW: Phase Jitter: 12 kHz~80 MHz True SineWave ±50ppm Min ±20% Max +7dBm Min into 50 Ω Load 2ms Typical, 10ms Max -14dBc Typical, -10dBc Max None >20 kHz @ -3dB <1ps RMS (1-sigma) Max 0.295 -0.008 +0.035 (7.50 -0.20 +0.89) CVS575S 500M Date Code 0.046 (1.16) 0.058 (1.47) 0.200 ±0.015 (5.08 ±0.38) #1 #2 #4 #3 0.046 (1.16) 0.200 (5.08) Denotes pad 1 SUGGESTED PAD LAYOUT 0.050 (1.27) via to ground PIN Function 1 2 3 4 Volt Control GND OUT Vdd 0.01µF 4 3 0.099 (2.50) 0.154 (3.91) 0.071 (1.80) 1 2 0.200 (5.08) Dimensions inches (mm) All dimensions are Max unless otherwise specified. CRYSTEK CORPORATION Rev: G Date: 17-Feb-2015 Page 2 of 3 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com CVS575S-500.000 True SineWave SAW Based VCSO 5×7.5mm SMD 3.3 Volts Frequency VS Temperature RECOMMENDED REFLOW SOLDERING PROFILE Ramp-Up 3°C/Sec Max. Critical Temperature Zone TEMPERATURE 260°C Ramp-Down 6°C/Sec. 217°C 200°C 150°C Preheat 180 Secs. Max. 90 Secs. Max. 8 Minutes Max. 260°C for 10 Secs. Max. NOTE: Reflow Profile with 240°C peak also acceptable. Parameter Conditions Mechanical Shock Mechanical Vibration Solderability MIL-STD-883, Method 2002, Condition B MIL-STD-883, Method 2007, Condition A MIL-STD-883, Method 2003 Resistance to Solvents Resistance to Soldering Heat Thermal Shock Moisture Resistance MIL-STD-202, Method 215 MIL-STD-202, Method 210, Condition I or J MIL-STD-883, Method 1011, Condition A MIL-STD-883, Method 1004 Rev: G Date: 17-Feb-2015 Page 3 of 3 CRYSTEK CORPORATION 12730 Commonwealth Drive • Fort Myers, Florida 33913 Phone: 239-561-3311 • 800-237-3061 Fax: 239-561-1025 • www.crystek.com