LH1539AB www.vishay.com Vishay Semiconductors Telecom Switch 1 Form A Photo Darlington Solid-State Relay FEATURES 1 • Solid-state relay and autopolarity optocoupler in one 8-pin package 8 DIP • Isolation test voltage 5300 VRMS 7 2 • Surface mountable • Optocoupler 3 6 4 - Bidirectional current detection - High CTR: 300 % 5 • Solid state relay i179055-1 i179034_12 - Form A LH1525 type - Low operating current - Typical RON 25 DESCRIPTION - Load voltage 400 V The LH1539 telecom switch consists of an optically isolated solid-state relay (SSR) form A and a bidirectional input optocoupler in a single 8-pin package. The SSR is ideal for switch hook and dial-pulse switching while the optocoupler performs ring detect and loop current sensing functions. Both the SSR and optocoupler provide 5300 VRMS of input-to-output isolation voltage. - Load current 120 mA - Current limit protection - Linear, AC/DC operation - Clean bounce free switching - Low power consumption • Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC The SSR is integrated on a monolithic receptor die using smart power technology. The SSR features low On resistance, high breakdown voltage, and current-limit circuitry that protects the relay from telephone line induced lightning surges. APPLICATIONS • General telecom switching - On/off hook switching The optocoupler provides bidirectional current sensing via two anti parallel GaAs infrared emitting diodes. Very high current transfer ratio (CTR) is achieved by coupling to a photodarlington transistor. This high CTR allows the user to minimize the size of the ring detector capacitor. - Dial pulse - Ring current detection - Loop current sensing AGENCY APPROVALS UL1577: file no. E52744 system code H, double protection CSA: certification no. 093751 BSI/BABT: certification no. 7980 ORDERING INFORMATION L H 1 5 PART NUMBER PACKAGE DIP-8, tubes Rev. 1.6, 08-Sep-11 3 9 A DIP-8 B ELECTR. PACKAGE VARIATION CONFIG. 7.62 mm UL, CSA, BSI LH1539AB Document Number: 83832 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1539AB www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER SSR INPUT LED continuous forward current LED reverse voltage OUTPUT DC or peak AC load voltage Continuous DC load current SSR Ambient operating temperature range Storage temperature range Pin soldering temperature (1) Input to output isolation voltage Package power dissipation (continuous) Optocoupler INPUT LED continuous forward current LED reverse voltage OUTPUT Collector emitter breakdown voltage Phototransistor power dissipation TEST CONDITION SYMBOL VALUE UNIT IR 10 μA IF VR 50 8 mA V VL IL 400 120 V mA Tamb Tstg Tsld VISO Pdiss - 40 to + 85 - 40 to + 85 260 5300 600 °C °C °C VRMS mW IF VR 50 3 mA V BVCEO Pdiss 30 150 V mW IL 50 μA t = 10 s max. t = 60 s min. IR 10 μA Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER INPUT LED forward current, switch turn-on LED forward current, switch turn-off LED forward voltage OUTPUT On-resistance Off-resistance Current limit Off-state leakage current Capacitance pin 4 to pin 6 TRANSFER Optocoupler LED forward voltage DC current transfer ratio Saturation voltage Collector emitter leakage current TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT IL = 100 mA, t = 10 ms VL = ± 300 V IF = 3 mA IFon IFoff VF 0.5 0.4 1.2 1 0.1 0.8 mA mA V IF = 3 mA, IL = ± 50 mA IF = 0 mA, VL = ± 100 V IF = 5 mA, t = 5 ms IF = 0 mA, VL = ± 100 V IF = 0 mA, VL = 1 V IF = 0 mA, VL = 50 V RON ROFF ILMT IO CO CO IF = 10 mA IF = 0.05 mA, VCE = 0.9 V IF = 0.05 mA, IC = 0.15 mA IF = 0 mA, VCE = 5 V VF CTRDC VCEsat ICEO 17 170 0.9 300 1.4 25 5000 210 0.04 55 10 33 270 100 1.2 1.5 1 N/A G mA nA pF pF V % V Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Turn-on time Turn-off time TEST CONDITION IF = 5 mA, IL = 50 mA IF = 5 mA, IL = 50 mA SYMBOL ton toff MIN. TYP. MAX. 2 0.5 UNIT ms ms SYMBOL IFon MIN. 3 TYP. MAX. 20 UNIT mA RECOMMENDED OPERATING CONDITIONS PARAMETER LED forward current, switch turn-on Rev. 1.6, 08-Sep-11 TEST CONDITION Tamb = - 40 °C to + 85 °C Document Number: 83832 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1539AB www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 1.20 1.5 IF = 50 mA IF = 20 mA 1.4 1.3 1.2 IF = 1.0 mA IF = 2.0 mA 1.1 1.0 - 40 ilh1539ab_01 - 20 IF = 5.0 mA IF = 10 mA 0 20 40 60 LED Forward Voltage (V) LED Forward Voltage (V) 1.6 1.10 1.00 0.90 0.80 0.70 - 40 80 Ambient Temperature, TA (°C) ilh1539ab_04 20 40 60 80 40 300 IL = 100 mA 200 100 0 - 100 - 40 ilh1539ab_02 20 10 0 - 10 - 20 - 30 - 40 - 20 0 20 40 60 80 Ambient Temperature, TA (°C) - 40 ilh1539ab_05 IL = 50 mA 30 20 10 0 - 10 - 20 - 30 - 40 - 40 ilh1539ab_03 - 20 0 20 40 60 80 Ambient Temperature, TA (°C) Fig. 3 - On-Resistance vs. Temperature Rev. 1.6, 08-Sep-11 - 20 0 20 40 60 80 Ambient Temperature, TA (°C) Fig. 5 - Current Limit vs. Temperature AC/DC On-resistance Variation (%) Normalized to Datasheet Ron Specification at IF = 5 mA 50 40 IF = 5.0 mA, t = 5 ms 30 Fig. 2 - LED Current for Switch Turn-on/off vs. Temperature Change in On-resistance (%) Normalized to 25 °C 0 Fig. 4 - LED Dropout Voltage vs. Temperature Change in Current Limit (%) Normalized to 25 °C LED Forward Current for Switch Turn-on/off (%) Norm. to 25 °C Fig. 1 - LED Voltage vs. Temperature - 20 Ambient Temperature, TA (°C) 9 8 7 6 5 4 3 2 1 0 0.0 ilh1539ab_06 1.0 2.0 3.0 4.0 5.0 LED Forward Current (mA) Fig. 6 - Variation in On-Resistance vs. LED Current Document Number: 83832 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1539AB www.vishay.com Vishay Semiconductors 70 0.6 50 40 30 20 0.4 0.3 0.2 0.1 10 0.0 0 0 20 40 60 80 102 100 Applied Voltage (V) ilh1539ab_07 104 105 Frequency (Hz) Fig. 10 - Insertion Loss vs. Frequency 100 60 40 20 0 102 103 104 105 106 90 70 60 50 40 30 20 10 0 0 85 °C 2.5 2.0 1.5 70 °C 1.0 50 °C 0.5 0.0 0 50 ilh1539ab_09 100 150 200 250 300 350 400 Load Voltage (V) Fig. 9 - Leakage Current vs. Applied Voltage at Elevated Temperatures Rev. 1.6, 08-Sep-11 100 150 200 250 300 350 400 Load Voltage (V) Fig. 11 - Leakage Current vs. Applied Voltage Change in Breakdown Voltage (%) Normalized to 25 °C 3.0 50 ilh1539ab_11 Fig. 8 - Output Isolation 3.5 IF = 0 mA 80 107 Frequency (Hz) ilh1539ab_08 Off-state Leakage Current (pA) 100 VP = 10 V RL = 50 Ω 80 Isolation (dB) 103 ilh1539ab_10 Fig. 7 - Output Isolation Off-state Leakage Current (nA) RL = 600 Ω 0.5 Insertion Loss (dB) Capacitance (pF) 60 8 6 4 2 0 -2 -4 -6 -8 - 40 ilh1539ab_12 - 20 0 20 40 60 80 Ambient Temperature, TA (°C) Fig. 12 - Switch Breakdown Voltage vs. Temperature Document Number: 83832 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1539AB www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters DIP pin one ID 4 3 2 1 5 6 7 8 6.81 6.48 ISO method A 9.91 9.63 1.14 0.76 7.62 typ. 0.79 4° typ. 3.81 3.30 1.27 10° 0.89 0.51 0.56 0.46 3° to 9° 0.30 0.20 2.54 typ. 6.35 5.84 3.30 2.79 i178008 PACKAGE MARKING (example) LH1539 V YWW H 68 Rev. 1.6, 08-Sep-11 Document Number: 83832 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000