Designed and Manufactured in Germany Specification Oscillator type: Rev.: 1 Date: 2014-06-20 AXLE1000 UHF Temperature Compensated Crystal Oscillator (TCXO) Parameter min. Frequency range Nominal frequencies Frequency stability Initial tolerance vs. operating temperature range 300 1300 1000.000 / 1200.000 vs. supply voltage variation vs. load change Long term (aging) per year Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC slope (∆f / ∆VC) EFC input impedance RF output Signal waveform Load Output level Harmonics Sub-harmonics (multiples of fOUT/10) Spurious Phase noise Supply voltage VS Current consumption (steady state) Operating temperature range ±5 ±0.5 to ±5 See tables 1 & 2 ±1 ±1 ±1 ±5 0.5 3. 2.5 Positive 4.5 100 MHz MHz ppm ppm ppm ppm ppm ppm Condition @ 25°C Option 1 & 2 VS ±5% RL ±5% ppm V kΩ Sine wave 50 Ω +7 +10 dBm -45 -40 dBc -45 -40 dBc -80 dBc Consult factory 11.4 12.0 12.6 V 80 mA -20 +70 °C 54x40x19 Enclosure (see drawing) (LxWxH) Weight Packing Notes: 1. 2. typ. max. Unit 60 mm g (Note 2) (Note 3) @ +25°C h = 2.0 mm Palette Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated Depending on frequency multiplication factor may be lower or higher than 10 Other supply voltages on request Absolute Maximum Ratings Parameter min. max. Supply Voltage VS Control Voltage VC Storage Temperature -0.5 -0.5 -55 VS + 10% 6 +125 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXLE1000 Rev.1 Drawing D0 Page 1(4) Unit Condition V V °C VS to GND VC to GND www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Frequency stability vs. temperature Option 1 05 10 15 20 25 30 35 50 Table 1 Stability [ppm] ±0.5 ±1.0 ±1.5 ±2.0 ±2.5 ±3.0 ±3.5 ±5.0 Lower Temperature Option 2 T [°C] 0 0 1 -10 2 -20 3 -30 4 -40 Upper Temperature Option 2 T [°C] A +50 B +60 C +70 D +75 E +80 F +85 Table 2 Ordering Code Option 2 [Temperature Revision range] AXLE1000 Table 1 Table 2 Rev.1 Example: AXLE1000-20-2C_Rev.1 – 1000.000 MHz Model Option 1 [Stability] Frequency [MHz] 1000.000 Handling and Testing Parameter Procedure Handling and Testing Processing Parameter Source Application Note AXAN-011 Application Note AXAN-012 Procedure Electrostatic discharge (ESD) THD devices SMD devices Washable RoHS compliant GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany IEC60749-26 IEC60749-27 Yes Yes AXLE1000 Rev.1 Drawing D0 Page 2(4) www.axtal.com www.axtal.com Condition HBM MM 2000 V 200 V No No www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Enclosure drawing Pin connections Pin# Symbol 1 VC 2 GND 3 VS SMA RF OUT Function Control Voltage (EFC) Ground Supply Voltage RF Output Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part … 2-17 IEC 60679-1 Clause 5.6.2 MIL-STD202G Method 112E 2-20 2-58 5.6.3 208H 210F 2-27 5.6.8 213B Vibration, 2-6 5.6.7.1 201A sinusoidal* 204D Vibration, 2-64 5.6.7.3 214A random* Endurance tests 108A - ageing 5.7.1 - extended aging 5.7.2 Other environmental conditions on request MIL-STD810F Method MIL-PRF55310D Clause 3.6.1.2 3.6.52 3.6.48 516.4 3.6.40 516.4-4 3.6.38.1 3.6.38.2 3.6.38.3 3.6.38.4 514.5 4.8.35 Test conditions (IEC) Gross leak: Test Qc, Fine leak: Test Qk Test Ta Method 1 Test Td1 Method 2 Test Td2 Method 2 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Fdb 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXLE1000 Rev.1 Drawing D0 Page 3(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Revision History Rev. Drawing Date [dd.mm.yyyy] Remarks Author Checked 1 D0 20.06.2014 First issue HH HH GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXLE1000 Rev.1 Drawing D0 Page 4(4) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]