2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP ATTENTION Part Number: AA2810AVWD1S White OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 2.8mmX0.8mm right angle SMT LED, 1.2mm thickness. z The source color devices are made with InGaN Light Emitting Diode. z Low power consumption. z Ideal for backlight and indicator. z Electrostatic discharge and power surge could damage the LEDs. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs. z RoHS compliant. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.0039") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAK2449 REV NO: V.4B DATE: AUG/30/2014 PAGE: 1 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005932 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 2. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. SPEC NO: DSAK2449 REV NO: V.4B DATE: AUG/30/2014 PAGE: 2 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005932 Selection Guide Part No. Dice AA2810AVWD1S Iv (mcd) [2] @ 20mA Lens Type White (InGaN) Water Clear Viewing Angle [1] Min. Typ. 2θ1/2 1300 1700 110° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device VF [1] Forward Voltage White IR Reverse Current White x [2] Typ. Max. Units Test Conditions 3.3 4.0 V IF=20mA 50 uA VR = 5V pF VF=0V;f=1MHz 0.31 Chromaticity Coordinates White y [2] C 0.31 Capacitance White 100 Notes: 1.Forward Voltage: +/-0.1V. 2. Measurement Tolerance Of The Chromaticity Coordinates Is ±0.01. 3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter White Units Power dissipation 120 mW DC Forward Current 30 mA Peak Forward Current [1] 100 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAK2449 REV NO: V.4B DATE: AUG/30/2014 PAGE: 3 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005932 White AA2810AVWD1S SPEC NO: DSAK2449 REV NO: V.4B DATE: AUG/30/2014 PAGE: 4 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005932 AA2810AVWD1S White CIE 0.40 c0 0.35 y b1 0.30 b2 a0 0.25 a2 0.20 0.20 0.25 0.30 0.35 0.40 x a2 b1 x y x y x y 0.263 0.213 0.282 0.245 0.298 0.271 0.282 0.245 0.298 0.271 0.313 0.296 0.265 0.265 0.286 0.299 0.306 0.332 0.242 0.226 0.265 0.265 0.286 0.299 0.313 0.296 0.329 0.325 0.329 0.325 0.358 0.372 0.329 0.371 0.363 0.400 0.306 0.332 0.329 0.371 a0 c0 b2 Notes: Shipment may contain more than one chromaticity regions. Orders for single chromaticity region are generally not accepted. Measurement tolerance of the chromaticity coordinates is ±0.01. SPEC NO: DSAK2449 REV NO: V.4B DATE: AUG/30/2014 PAGE: 5 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005932 AA2810AVWD1S Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAK2449 REV NO: V.4B DATE: AUG/30/2014 PAGE: 6 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005932 PACKING & LABEL SPECIFICATIONS AA2810AVWD1S Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAK2449 REV NO: V.4B DATE: AUG/30/2014 PAGE: 7 OF 7 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1201005932