USB 2.0 Test Report For Full Speed Peripheral Company Name: VID (Dec or Hex): Model Name: Product Type: Report Date: HOLTEK 1241 The VID for the company who applies the USB-IF logo. HT56RB688 Keyboard 2013/08/05 Test Result: PASS Tester: Terry Kao Authorized Signature: USB Legal Disclaimer 1. TEST RESULT IS VALID ONLY TO THE ORIGINAL TESTED DEVICE MODEL. ALLION RESERVES THE RIGHT TO PROHIBIT OTHERS TO DISTORT, ISOLATE, FALSIFY, COPIED AND/OR BY ANY PROCESS TO CHANGE THE CONTENT OF THIS TEST REPORT UNLESS IT IS PRIOR APPROVED BY ALLION. 1 Project ID：KB-HOK-USB-016 Document Number：AR-TRL011413 USB Legacy USB Compliance Tests Frameworks Test Result (USB20CV): Pass Fail This test primarily covers USB-IF testing of devices and hubs for compliance with the standard commands in Chapters 9 and 11 of the USB 2.0 specification. This specification does not describe the full set of USB-IF tests and assertions for these devices. VID: 04d9 Chapter 9: PID: 6000 Pass Fail Interface: 1 MAX Power: 100 mA HID: Pass Fail Frameworks Test Result (USB30CV): Remote Wakeup: Yes N/A Pass Fail All USB peripherals are required to enumerate on a SuperSpeed host controller and pass all applicable tests within USB30CV. Failure framework test in USB30CV will prevent certification. VID: 04d9 Chapter 9: PID: 6000 Pass Fail Interface: 1 MAX Power: 100 mA HID: Pass Fail 2 Remote Wakeup: Yes N/A Project ID：KB-HOK-USB-016 Document Number：AR-TRL011413 USB Power Current Test Result: Pass Fail Power Type: Low Powered Device Operating Power: 10.08 mA (<= Max Power <= 100mA for Low Power) (<= Max Power <= 100mA for Self Power) (<= Max Power <= 500mA for High Power) Unconfiguration Power: 8.67 mA (<= 100mA) Configuration Power: 8.72 mA (<= Max Power <= 100mA for Low Power) (<= Max Power <= 500mA for High Power) Suspend Mode Power: N/A uA (Remote Wakeup Unsupported Device Only) (Remote Wakeup Supported Device=> Type “N/A”) (<= 2500uA for Self Power Hub or Non Compound Device) (<= 12500uA for Bus Power Hub or Compound Device) Suspend Mode Power with Remote Wakeup: 347 uA Suspend Mode Power without Remote Wakeup: 347 uA (Remote Wakeup Supported Device Only) (Remote Wakeup Unsupported Device => Type “N/A”) (<= 2500uA for Self Power Hub or Non Compound Device) (<= 12500uA for Bus Power Hub or Compound Device) Powered’ State Suspend Mode Power: 345 uA (<= 2500uA for not Supporting USB Battery Charging) (<= 100mA for Supporting USB Battery Charging) 3 Project ID：KB-HOK-USB-016 Document Number：AR-TRL011413 USB Interoperability Test Overall Result: Pass Fail OS: Win 7 EHCI Host Controller: Enumeration and Driver installation: Check operation of device Interoperability – Operate all devices Hot plug test – A Plug Hot plug test – B Plug Warm Boot test Remote Wake-up Test S3 Active Standby Test S3 Active Standby Resume Test Root Port Test S4 Active Hibernate Test S4 Active Hibernate Resume Test Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Fail Fail Fail Fail Fail Fail Fail Fail Fail Fail Fail Fail UHCI Host Controller: Interoperability – Operate all devices System Suspend/Resume Test– Operate DUT Warm Boot Test – Operate DUT Pass Pass Pass Fail Fail Fail OHCI Host Controller: Interoperability – Operate all devices System Suspend/Resume Test – Operate DUT Warm Boot Test – Operate DUT Pass Pass Pass Fail Fail Fail 4 N/A N/A Project ID：KB-HOK-USB-016 Document Number：AR-TRL011413 USB Low Signal Quality Test Result: Pass Fail Connector Type: Untethered (Tethered means no standard B or special B connector) Low Speed Upstream Signal Quality: Pass Fail Inrush Current Test: Pass Fail Back Voltage Test Result: (Enumerate before/after) Pass Fail D+: 0 mV / 0 mV D- : 0 mV / 0 mV VBus: 0 mV / 0 mV (All values <= 400mV) Miscellaneous: Pass Fail Bypass Capacitance Check: Pass BC 1.2 Implemented Check: Support 5 Fail N/A Project ID：KB-HOK-USB-016 Document Number：AR-TRL011413 USB More Detail Test Result: 1. Low Speed Upstream Signal Quality: Pass • • • • • • • • • • Overall result: pass! Sync result: sync passes Signal eye: eye passes EOP width: 166.23 ns EOP width passes Measured signaling rate: 12.0118 MHz signal rate passes Edge Monotonicity: 26 mV Monotonic Edge passes Crossover voltage range: 1.55 V to 1.62 V, mean crossover 1.58 V (first crossover at 1.62 V, 10 other differential crossovers checked) crossover voltages pass Consecutive jitter range: -172.726 ps to 204.649 ps, RMS jitter 143.153 ps Paired JK jitter range: -28.894 ps to 113.791 ps, RMS jitter 83.016 ps Paired KJ jitter range: -60.254 ps to 70.034 ps, RMS jitter 46.823 ps jitter passes Additional Information • • • Rising Edge Rate: 337.78 V/us (Equivalent risetime = 7.82 ns) Falling Edge Rate: 315.05 V/us (Equivalent falltime = 8.38 ns) Edge Rate Match: 6.97% (limit +/-10%) 6 Project ID：KB-HOK-USB-016 Document Number：AR-TRL011413 USB SignalData and Eye 7 Project ID：KB-HOK-USB-016 Document Number：AR-TRL011413 USB 2. Inrush Current: Pass • • • Overall result: pass! Inrush at 5.000 V: 47.3160 µC Inrush passes Region 1 Start: 0.00093 ms - End: 0.150 ms = 47.32 µC Hot Plug (Attach) Current Draw 8 Project ID：KB-HOK-USB-016 Document Number：AR-TRL011413 USB Notice: Test result is valid only to the original tested device model. The content of test report may not be copied or re-transmitted (except for the entire report) unless it is prior approved by Allion. Test Procedure Reference: 1. USB-IF Compliance Update Page---Interoperability Gold Tree Update http://compliance.usb.org/resources/GoldSuite%20Test%20Procedure.pdf 2. Universal Serial Bus Implementers Forum Full and Low Speed Electrical and Interoperability Compliance Test Procedure, version: 1.3 9 Project ID：KB-HOK-USB-016 Document Number：AR-TRL011413