PASS - Holtek

USB 2.0 Test Report
For
Full Speed Peripheral
Company Name:
VID (Dec or Hex):
Model Name:
Product Type:
Report Date:
HOLTEK
0x04D9 The VID for the company who applies the USB-IF logo.
HT66FB540
Keyboard
2013/07/15
Test Result: PASS
Tester:
Shef Hsieh
Authorized Signature:
USB
Legal Disclaimer
1.
TEST RESULT IS VALID ONLY TO THE ORIGINAL TESTED DEVICE MODEL.
ALLION
RESERVES THE RIGHT TO PROHIBIT OTHERS TO DISTORT, ISOLATE, FALSIFY, COPIED
AND/OR BY ANY PROCESS TO CHANGE THE CONTENT OF THIS TEST REPORT UNLESS
IT IS PRIOR APPROVED BY ALLION.
1
Project ID:KB-HOK-USB-014
Document Number:AR-TRL011413
USB
Legacy USB Compliance Tests
Frameworks Test Result (USB20CV):
Pass
Fail
This test primarily covers USB-IF testing of devices and hubs for compliance with the standard
commands in Chapters 9 and 11 of the USB 2.0 specification. This specification does not describe the
full set of USB-IF tests and assertions for these devices.
VID: 04d9
Chapter 9:
PID: 8015
Pass
Fail
Interface: 1 MAX Power: 100 mA
HID:
Pass
Fail
Frameworks Test Result (USB30CV):
Remote Wakeup: Yes
N/A
Pass
Fail
All USB peripherals are required to enumerate on a SuperSpeed host controller and pass all applicable
tests within USB30CV. Failure framework test in USB30CV will prevent certification.
VID: 04d9
Chapter 9:
PID: 8015
Pass
Fail
Interface: 1 MAX Power: 100 mA
HID:
Pass
Fail
2
Remote Wakeup: Yes
N/A
Project ID:KB-HOK-USB-014
Document Number:AR-TRL011413
USB
Power Current Test Result:
Pass
Fail
Power Type: Low Powered Device
Operating Power: 10.89 mA
(<= Max Power <= 100mA for Low Power)
(<= Max Power <= 100mA for Self Power)
(<= Max Power <= 500mA for High Power)
Unconfiguration Power: 10.64 mA
(<= 100mA)
Configuration Power: 10.56 mA
(<= Max Power <= 100mA for Low Power)
(<= Max Power <= 500mA for High Power)
Suspend Mode Power: N/A uA
(Remote Wakeup Unsupported Device Only)
(Remote Wakeup Supported Device=> Type “N/A”)
(<= 2500uA for Self Power Hub or Non Compound Device)
(<= 12500uA for Bus Power Hub or Compound Device)
Suspend Mode Power with Remote Wakeup: 368 uA
Suspend Mode Power without Remote Wakeup: 368 uA
(Remote Wakeup Supported Device Only)
(Remote Wakeup Unsupported Device => Type “N/A”)
(<= 2500uA for Self Power Hub or Non Compound Device)
(<= 12500uA for Bus Power Hub or Compound Device)
Powered’ State Suspend Mode Power: 366 uA
(<= 2500uA for not Supporting USB Battery Charging)
(<= 100mA for Supporting USB Battery Charging)
3
Project ID:KB-HOK-USB-014
Document Number:AR-TRL011413
USB
Interoperability Test Overall Result:
Pass
Fail
OS: Win 7
EHCI Host Controller:
Enumeration and Driver installation:
Check operation of device
Interoperability – Operate all devices
Hot plug test – A Plug
Hot plug test – B Plug
Warm Boot test
Remote Wake-up Test
S3 Active Standby Test
S3 Active Standby Resume Test
Root Port Test
S4 Active Hibernate Test
S4 Active Hibernate Resume Test
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Fail
Fail
Fail
Fail
Fail
Fail
Fail
Fail
Fail
Fail
Fail
Fail
UHCI Host Controller:
Interoperability – Operate all devices
System Suspend/Resume Test– Operate DUT
Warm Boot Test – Operate DUT
Pass
Pass
Pass
Fail
Fail
Fail
OHCI Host Controller:
Interoperability – Operate all devices
System Suspend/Resume Test – Operate DUT
Warm Boot Test – Operate DUT
Pass
Pass
Pass
Fail
Fail
Fail
4
N/A
N/A
Project ID:KB-HOK-USB-014
Document Number:AR-TRL011413
USB
Low Signal Quality Test Result:
Pass
Fail
Connector Type: Untethered (Tethered means no standard B or special B connector)
Low Speed Upstream Signal Quality:
Pass
Fail
Inrush Current Test:
Pass
Fail
Back Voltage Test Result: (Enumerate before/after)
Pass
Fail
D+: 0 mV / 0 mV
D- : 0 mV / 0 mV
VBus: 0 mV / 0 mV
(All values <= 400mV)
Miscellaneous:
Pass
Fail
Bypass Capacitance Check:
Pass
BC 1.2 Implemented Check:
Support
5
Fail
N/A
Project ID:KB-HOK-USB-014
Document Number:AR-TRL011413
USB
More Detail Test Result:
1. Full Speed Upstream Signal Quality: Pass
•
•
•
•
•
•
•
•
•
•
Overall result: pass!
Sync result:
sync passes
Signal eye:
eye passes
EOP width: 166.88 ns
EOP width passes
Measured signaling rate: 12.0010 MHz
signal rate passes
Edge Monotonicity: 23 mV
Monotonic Edge passes
Crossover voltage range: 1.50 V to 1.61 V, mean crossover 1.56 V
(first crossover at 1.60 V, 10 other differential crossovers checked)
crossover voltages pass
Consecutive jitter range: -360.191 ps to 346.601 ps, RMS jitter 318.953 ps
Paired JK jitter range: -56.254 ps to 108.236 ps, RMS jitter 86.254 ps
Paired KJ jitter range: -62.175 ps to 55.983 ps, RMS jitter 42.409 ps
jitter passes
Additional Information
•
•
•
Rising Edge Rate: 322.03 V/us (Equivalent risetime = 8.20 ns)
Falling Edge Rate: 344.03 V/us (Equivalent falltime = 7.67 ns)
Edge Rate Match: 6.61% (limit +/-10%)
6
Project ID:KB-HOK-USB-014
Document Number:AR-TRL011413
USB
SignalData and Eye
7
Project ID:KB-HOK-USB-014
Document Number:AR-TRL011413
USB
2. Inrush Current: Pass
•
•
•
Overall result: pass!
Inrush at 5.000 V: 33.6961 µC
Inrush passes
Region 1 Start: 0.00159 ms - End: 0.173 ms = 33.7 µC
Hot Plug (Attach) Current Draw
8
Project ID:KB-HOK-USB-014
Document Number:AR-TRL011413
USB
Notice: Test result is valid only to the original tested device model. The content of test
report may not be copied or re-transmitted (except for the entire report) unless it is
prior approved by Allion.
Test Procedure Reference:
1. USB-IF Compliance Update Page---Interoperability Gold Tree Update
http://compliance.usb.org/resources/GoldSuite%20Test%20Procedure.pdf
2. Universal Serial Bus Implementers Forum Full and Low Speed Electrical and
Interoperability Compliance Test Procedure, version: 1.3
9
Project ID:KB-HOK-USB-014
Document Number:AR-TRL011413