USB 2.0 Test Report For Low Speed Peripheral Company Name: VID (Dec or Hex): Model Name: Product Type: Report Date: HOLTEK 0x04D9 The VID for the company who applies the USB-IF logo. HT68FB240 Keyboard 2013/07/01 Test Result: PASS Tester: Shef Hsieh Authorized Signature: USB Legal Disclaimer 1. TEST RESULT IS VALID ONLY TO THE ORIGINAL TESTED DEVICE MODEL. ALLION RESERVES THE RIGHT TO PROHIBIT OTHERS TO DISTORT, ISOLATE, FALSIFY, COPIED AND/OR BY ANY PROCESS TO CHANGE THE CONTENT OF THIS TEST REPORT UNLESS IT IS PRIOR APPROVED BY ALLION. 1 Project ID：KB-HOK-USB-013 Document Number：AR-TRL011413 USB Legacy USB Compliance Tests Frameworks Test Result (USB20CV): Pass Fail This test primarily covers USB-IF testing of devices and hubs for compliance with the standard commands in Chapters 9 and 11 of the USB 2.0 specification. This specification does not describe the full set of USB-IF tests and assertions for these devices. VID: 04d9 Chapter 9: PID: ff00 Pass Fail Interface: 2 MAX Power: 100 mA HID: Pass Fail Frameworks Test Result (USB30CV): Remote Wakeup: Yes N/A Pass Fail All USB peripherals are required to enumerate on a SuperSpeed host controller and pass all applicable tests within USB30CV. Failure framework test in USB30CV will prevent certification. VID: 04d9 Chapter 9: PID: ff00 Pass Fail Interface: 2 MAX Power: 100 mA HID: Pass Fail 2 Remote Wakeup: Yes N/A Project ID：KB-HOK-USB-013 Document Number：AR-TRL011413 USB Power Current Test Result: Pass Fail Power Type: Low Powered Device Operating Power: 32.30 mA (<= Max Power <= 100mA for Low Power) (<= Max Power <= 100mA for Self Power) (<= Max Power <= 500mA for High Power) Unconfiguration Power: 9.48 mA (<= 100mA) Configuration Power: 7.36 mA (<= Max Power <= 100mA for Low Power) (<= Max Power <= 500mA for High Power) Suspend Mode Power: N/A uA (Remote Wakeup Unsupported Device Only) (Remote Wakeup Supported Device=> Type “N/A”) (<= 2500uA for Self Power Hub or Non Compound Device) (<= 12500uA for Bus Power Hub or Compound Device) Suspend Mode Power with Remote Wakeup: 616 uA Suspend Mode Power without Remote Wakeup: 582 uA (Remote Wakeup Supported Device Only) (Remote Wakeup Unsupported Device => Type “N/A”) (<= 2500uA for Self Power Hub or Non Compound Device) (<= 12500uA for Bus Power Hub or Compound Device) Powered’ State Suspend Mode Power: 407 uA (<= 2500uA for not Supporting USB Battery Charging) (<= 100mA for Supporting USB Battery Charging) 3 Project ID：KB-HOK-USB-013 Document Number：AR-TRL011413 USB Interoperability Test Overall Result: Pass Fail OS: Win 7 EHCI Host Controller: Enumeration and Driver installation: Check operation of device Interoperability – Operate all devices Hot plug test – A Plug Hot plug test – B Plug Warm Boot test Remote Wake-up Test S3 Active Standby Test S3 Active Standby Resume Test Root Port Test S4 Active Hibernate Test S4 Active Hibernate Resume Test Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Fail Fail Fail Fail Fail Fail Fail Fail Fail Fail Fail Fail UHCI Host Controller: Interoperability – Operate all devices System Suspend/Resume Test– Operate DUT Warm Boot Test – Operate DUT Pass Pass Pass Fail Fail Fail OHCI Host Controller: Interoperability – Operate all devices System Suspend/Resume Test – Operate DUT Warm Boot Test – Operate DUT Pass Pass Pass Fail Fail Fail 4 N/A N/A Project ID：KB-HOK-USB-013 Document Number：AR-TRL011413 USB Low Signal Quality Test Result: Pass Fail Connector Type: Tethered (Tethered means no standard B or special B connector) Low Speed Upstream Signal Quality: Pass Fail Inrush Current Test: Pass Fail Back Voltage Test Result: (Enumerate before/after) Pass Fail D+: 0 mV / 0 mV D- : 0 mV / 0 mV VBus: 2.65 mV / 2.65 mV (All values <= 400mV) Miscellaneous: Pass Fail Bypass Capacitance Check: Pass BC 1.2 Implemented Check: Support 5 Fail N/A Project ID：KB-HOK-USB-013 Document Number：AR-TRL011413 USB More Detail Test Result: 1. Low Speed Upstream Signal Quality: Pass • • • • • • • • • • Overall result: pass! Sync result: sync passes Signal eye: eye passes EOP width: 1.33 us EOP width passes Measured signaling rate: 1.5007 MHz signal rate passes Edge Monotonicity: 60 mV Monotonic Edge passes Crossover voltage range: 1.62 V to 1.92 V, mean crossover 1.77 V (first crossover at 1.68 V, 20 other differential crossovers checked) crossover voltages pass Consecutive jitter range: -3.613 ns to 3.656 ns, RMS jitter 2.638 ns Paired JK jitter range: -2.284 ns to 1.348 ns, RMS jitter 1.179 ns Paired KJ jitter range: -1.592 ns to 1.432 ns, RMS jitter 0.880 ns jitter passes Additional Information • • • Rising Edge Rate: 25.34 V/us (Equivalent risetime = 104.16 ns) Falling Edge Rate: 25.33 V/us (Equivalent falltime = 104.22 ns) Edge Rate Match: 0.05% (limit +/-20%) 6 Project ID：KB-HOK-USB-013 Document Number：AR-TRL011413 USB SignalData and Eye 7 Project ID：KB-HOK-USB-013 Document Number：AR-TRL011413 USB 2. Inrush Current: Pass • • • Overall result: pass! Inrush at 5.000 V: 16.8728 µC Inrush passes Region 1 Start: 0.00112 ms - End: 0.132 ms = 16.87 µC Hot Plug (Attach) Current Draw 8 Project ID：KB-HOK-USB-013 Document Number：AR-TRL011413 USB Notice: Test result is valid only to the original tested device model. The content of test report may not be copied or re-transmitted (except for the entire report) unless it is prior approved by Allion. Test Procedure Reference: 1. USB-IF Compliance Update Page---Interoperability Gold Tree Update http://compliance.usb.org/resources/GoldSuite%20Test%20Procedure.pdf 2. Universal Serial Bus Implementers Forum Full and Low Speed Electrical and Interoperability Compliance Test Procedure, version: 1.3 9 Project ID：KB-HOK-USB-013 Document Number：AR-TRL011413