R EM-CCD camera series Multiply faster The ImagEM X2 is an extremely versatile camera that quietly delivers 70 frames/s at full frame and up to 1076 frames/s with analog binning and regions of interest. With very high signal to noise in near dark conditions and extremely low dark current, the ImagEM X2 enables quantitative ultra-low light imaging both for long integration times and at high speed. With EM gain off, the extremely deep full well capacity can extract information from the lowest contrast bright images. Additional new features allow for optimized camera triggering, on-board for EM gain protection, streamlined connectivity through IEEE1394b, improved overall signal to noise and increased non-EM dynamic range. Hamamatsu has taken the beloved 512 × 512 EM-CCD sensor and created a masterfully redesigned camera that delivers maximum speed and precision performance. The ImagEM X2-1K 1024 ×1024 version is also available. High-speed readout (ImagEM X2) 70 frames/s at full resolution 1076 frames/s at Sub-array 16 pixel, 4×4 binning The ImagEM X2 expertly handles a wide range of applications from om bright light, Hungry for Photons With large pixels, high QE, and relatively zero readout noise, EM-CCD technology performs in low light conditions. How low light? When you've got fewer than 10 photons per pixel between the sample and background, EM-CCDs are the perfect tool for the job, delivering the best SNR of any camera technology. For high mag, biologically relevant applications with routine exposure times of 10 ms to 30 ms, the sample is likely emitting hundreds to thousands of photons per pixel. But with faster speeds come shorter exposure times, risking the ability to capture more than tens of photons per pixel in one shot and therefore pushing the application into the ultra-low light zone. The ImagEM X2 series makes these super-fast exposures possible and has the sensitivity to provide visually pleasing and quantitatively meaningful images in a photon-starved environment. New Features Faster readout By clocking pixel readout at 22 MHz, the ImagEM X2 is able to achieve 70.4 frames/s with full frame resolution. That's more than 2× the original ImagEM and is faster than any commercially available camera using the sensor. The ImagEM X2-1K is able to run 18.5 frames/s with full frame resorution. ImagEM X2 (Clock: 22 MHz) Binning 1×1 2×2 4×4 512 70.4 131 231 ImagEM X2-1K (Clock: 22 MHz) Sub-array (Effective vertical width) 256 128 64 32 133 241 405 613 238 400 606 813 389 588 794 962 Binning 16 820 981 1076 1×1 2×2 4×4 1024 18.5 34.7 61.8 Sub-array (Effective vertical width) 512 256 128 64 32 34.9 62.7 104 156 208 62.5 104 155 207 248 102 154 205 245 272 (Unit: frames/s) 16 249 275 288 (Unit: frames/s) Corner readout By selectively imaging at the edge of the sensor, closest to the read register of the chip, it is possible to achieve even greater speeds of small ROIs. ImagEM X2 (Clock: 22 MHz) ImagEM X2-1K (Clock: 22 MHz) Sub-array Binning 512×512 256×256 128×128 64×64 70.4 133 285 495 1×1 131 238 456 699 2×2 231 389 645 863 4×4 32×32 741 901 981 16×16 893 981 1076 Binning 1×1 2×2 4×4 Sub-array 1024×1024 512×512 256×256 128×128 64×64 32×32 16×16 18.5 34.9 79.5 161 237 237 298 34.7 62.5 126 215 274 274 307 61.8 102 179 256 293 293 305 (Unit: frames/s) (Unit: frames/s) Lower readout noise In any image sensor, faster readout means increased readout noise. Yet readout noise is considered irrelevant for EMCCDs because of the EM gain. The ImagEM X2 series even before applying EM gain, has fast speed and low readout noise. But didn’t we just say readout noise in EM-CCD was irrelevant? Yes, in SNR equations this is true. However, if the primary purpose of EM gain is to overcome readout noise, then this will be accomplished with less gain in the ImagEM X2 series and less voltage in the EM register, translating into theoretically more stable EM gain calibrations and greater sensor longevity. ImagEM X2(C9100-23B) Type number ImagEM X2-1K(C9100-24B) Readout noise EM-CCD EM gain 36 electrons (at 22 MHz) 15 electrons (at 22 MHz) (rms) (typ.) readout 4× 25 electrons (at 11 MHz) 10 electrons (at 11 MHz) 8 electrons (at 0.6875 MHz) NORMAL CCD readout 3 electrons (at 0.6875 MHz) 1 electron max. EM gain1200× 8 electrons (at 0.6875 MHz) 10 electrons (at 0.6875 MHz) low contr contrast to ultra-low light imaging. Mechanical shutter The ImagEM X2 series includes an integrated mechanical shutter in order to protect the camera from EM gain degradation and to lessen afterimage effects. The mechanical shutter is software controlled. EM gain measurement and calibration Gain aging is a known and expected process in EM technology. Even when every care is taken to minimize gain aging, use of the camera in EM mode, especially with high gains or high intensity light, can degrade the gain. Since this is a usedependent phenomenon, it's important to know when it's happened and to have the ability to easily recalibrate. These two functions in the ImagEM X2 series make this crucial maintenance of the camera software accessible and user friendly. IEEE 1394b connectivity The data rates of the ImagEM X2 series are well suited to the trusted and easy to use 1394b connectivity. SMA triggering ports In its new incarnation, the ImagEM X2 series sports four shiny and compact SMA ports, one for input of an external trigger and three for output to other devices. These ports can be used to access an array of triggering options including three additional features: programmable trigger input/output, trigger delay and trigger ready. There is no denying that EM-CCD technology offers the best SNR for ultra-low light imaging, and the ImagEM X2 offers the fastest speeds combined with multiple engineering enhancements to allow you to make the most of this technology. Direct electron display Output signal can be indicated in "electrons" instead of pixel AD counts in application software. Black clip / White clip function It enables setting an upper or lower threshold of intensity. If there is a brighter or darker location than a sample of interest in an image, this function allows clipping the upper limit or lower limit of intensity to make Auto LUT function work effectively. Cooling status output The camera indicates when it has reached the target cooling temperature. Applications Protein-protein interaction Calcium waves in cell networks and intracellular ion flux Real time spinning disk confocal microscopy Image example: Real time confocal imaging Fast imaging of mouse brain cell with Cy3 imaged with confocal scanner unit EM gain: 150× Exposure time: 10 ms Single molecule imaging with TIRF microscopy Effective number of pixels: 512×512 Fluorescence in-vivo blood cell microscopy Objective lens: 40× Gene expression imaging using luminescence Binning: 1×1 Confocal unit: CSU-W1 Excitation laser: 561 nm High Sensitivity Quantum efficiency (%) High QE 100 90 80 70 60 50 40 30 20 10 0 300 The beloved EM-CCD sensor provides over 90 % peak QE. 400 500 600 700 800 Wavelength (nm) 900 1000 1100 High EM gain of maximum 1200× EM gain feature is ideal for live cell imaging because of shorter exposure times and reduced excitation light levels. Comparison of sensitivity with conventional camera: Luminescence imaging of HeLa cells expressing Renilla Luciferase. Conventional cooled CCD camera ImagEM X2 Low Noise Minimal dark noise is another benefit of stable cooling performance The dark current of a CCD depends on the temperature, and it decreases by half when the temperature drops by approximately 7 to 8 ˚C. Therefore, cooling a CCD is a very good way to reduce dark current noise. The ImagEM X2 series's stable cooling enables stable output and its water cooling minimizes dark current. Highly stabilized control of sensor temperature with either water or forced-air cooling Water or forced-air cooling is selectable for any application, and optimal cooling temperature can be set in each cooling mode. Optimized sensor drive methods significantly reduce the clock induced charge (CIC) Dark current consists of thermal charge and clock induced charge (CIC). CIC will dominate the dark charge in the images taken at short exposure time, and thermal charge will dominate the dark charge in images taken at longer exposures. The camera is adjusted to use the optimized drive method suitable to the scan speed. The biologist doesn't have to think about CIC optimization for long or short exposures. The camera handles it automatically. Comparison of noise: Comparison of two clock induced charge images ImagEM (C9100-13) ImagEM X2 (C9100-23B) Intensity profile (EM gain: 1200x, Exposure time: 30 ms, no light, enlarged 100 x 100 pixel region) Great Stability Highly stabilized EM gain by cooling temperature control Maintaining stable cooling temperature is essential to stable gain settings required for superior performance in long duration imaging and analysis. Very precise control of the cooling temperature in the ImagEM X2 series is a key benefit. Examples of temperature stability and EM gain stability EM gain stability EM gain stability (%) Cooling temp. (˚C) Temperature stability Elapse time (min) Elapse time (min) EM gain stability: ±1 % Temperature stability: ±0.01 ˚C Camera: C9100-23B Clock:22 MHz Cooling temperature: –65 ˚C Air cool, Ambient temperature: +20 ˚C Camera: C9100-23B Clock:22 MHz Cooling temperature: –65 ˚C Air cool, Ambient temperature: +20 ˚C Stability of mean bias value (Digitizer offset) The baseline is constant over time providing signal stability for long term measurements. Example of baseline variance Offset stability Offset stability (A/D count) Camera: C9100-23B Cooling method: Air cooled Clock: 22 MHz EM gain: 4× Exposure time: 13.93 ms No light Elapse time (min) EM gain protection It is important to operate the camera in ways that minimize the rate of gain aging and extend the life of the camera. The ImagEM X2 protects EM gain in two levels: EM gain warning and EM gain protection. EM gain protection mode stops charge transfer through the EM gain register when excessive output conditions have occurred which may damage the sensor. EM gain readjustment * Over time all EM-CCD cameras exhibit gain degradation. The EM gain can be readjusted by raising the voltage in the multiplying register. The EM gain readjustment can be done by software which comes with the camera. However, the number of times the EM gain can be readjusted is limited. *This feature is available when the camera is operated with DCAM-API. (DCAM-API is a software driver which supports HAMAMATSU digital cameras.) Selectable Readout Modes Select a readout mode for optimal image acquisition based on the sample brightness or desired frame rate or exposure time. EM-CCD readout Normal-CCD readout For short exposure, high sensitivity imaging Sample of EM-CCD readout Confocal calcium ion imaging of HeLa cells expressing yellow Chameleon 3.6. This image shows changes of histamine stimulated calcium ion with two Z positions and four time lapse. For high dynamic range imaging Sample of Normal-CCD readout Luminescence imaging of HeLa cells expressing Renilla Luciferase. Objective lens: UApo/340 20× Exposure time: 5 minutes Cooling method: Water cooled (-80 ˚C) Binning: 2×2 Objective lens: 100× EM gain: 300× Exposure time: 100 ms Confocal unit: CSU by Yokogawa Electric Co. CFP/YFP FRET: 2 wavelength imaging, W-view optics A8509 Z scan: 19 slices/2.5 s Piezoelectric Z stage Data courtesy of: Dr. Kenji Nagai, Dr. Kenta Saito Hokkaido Univ. Nikon imaging center An often overlooked benefit of EM-CCD technology is the ability to utilize the camera as a standard CCD. In non-EM mode, there is no effect of excess noise, and the large full well capacity and high dynamic range are ideal for bright light applications that have large intrascene dynamic range. The ImagEM X2 series provides a low read noise non-EM mode that can be an ideal choice for such applications. Photon Imaging Mode This is a unique technology to improve image quality at very low light level to overcome the limitation of excess noise factor from the electron multiplying process. This mode is most useful for signal levels at which maximum EM gain has no apparent signal or very little signal. The mode preserves quantitative linear signal output and also improves spatial resolution at very low light levels. Sample of photon imaging mode Fluorescence beads imaged with reduced excitation light intensity. Photon imaging mode OFF Photon imaging mode ON (Exposure time: 30.5 ms, EM gain: 1200×) On-board Image Processing The following real time processing functions are available. Background subtraction Effective for reducing fluorescence in image backgrounds. Shading correction This feature corrects the shading or uneven illumination in microscope images or other illumination systems. Recursive filter This feature provides random noise elimination in an image by weighted time based averaging. Frame averaging This feature provides noise elimination in an image by simple frame averaging and less “afterimage” effect than the recursive filter. Spot noise reducer This image processing function operates on random spots of intensity by comparing incoming images and eliminating signals that meet the criteria for noise in one image but not in others. This processing eliminates noise elements like cosmic rays. Specifications Type number Camera head type Window AR mask Imaging device Effective number of pixels Cell size Effective area Pixel clock rate EM-CCD readout Normal-CCD readout EM (electron multiplying) gain (typ.) *2 Ultra-low light detection Fastest readout speed Readout noise EM-CCD EM gain 4× (rms) (typ.) readout EM gain 1200× Normal CCD readout Full well capacity EM-CCD mode (typ.) Normal-CCD mode Analog gain EM-CCD 22 MHz readout 11 MHz/0.6875 MHz *4 Normal CCD readout at temperature control Cooling method / Forcedair cooled (Room temperature: 0 ˚C to +30 ˚C ) temperature at maximum cooling typ. *5 Water at temperature control cooled (Water temperature: +20 ˚C) at maximaum cooling typ. *6 Temperature stability (typ.) Forced-air cooled (-65 ˚C) Dark current Water cooled (-80 ˚C) (typ.) *7 Clock induced charge (typ.) Internal synchronus mode Exposure time *8 External trigger mode A/D converter Output signal / External control Sub-array Binning External trigger mode *10 Trigger output *10 Image processing features (real-time) *11 EM gain protection EM gain readjustment Lens mount Power requirements Power consumption Ambient storage temperature Ambient operating temperature Performance guaranteed temperature Ambient operating humidity C9100-23B (ImagEM X2 EM-CCD camera) C9100-24B (ImagEM X2-1K EM-CCD camera) Hermetic vacuum-sealed air/water-cooled head *1 Anti-reflection (AR) coatings on both sides, single window Yes No Electron Multiplying Back-Thinned Frame Transfer CCD 512 (H) × 512 (V) 1024 (H) × 1024 (V) 16 μm (H) × 16 μm (V) 13 μm (H) × 13 μm (V) 8.19 mm (H) × 8.19 mm (V) 13.3 mm (H) × 13.3 mm (V) 22 MHz, 11 MHz, 0.6875 MHz 0.6875 MHz 1×, 4× to 1200× 1×, 10× to 1200× Photon Imaging mode (1, 2, 3) 70.4 frames/s to 1076 frames/s 18.5 frames/s to 314 frames/s *3 36 electrons (at 22 MHz) 15 electrons (at 22 MHz) 25 electrons (at 11 MHz) 10 electrons (at 11 MHz) 8 electrons (at 0.6875 MHz) 3 electrons (at 0.6875 MHz) 1 electron max. 8 electrons (at 0.6875 MHz) 10 electrons (at 0.6875 MHz) 370 000 electrons 400 000 electrons 140 000 electrons 50 000 electrons 1× 0.5×, 1× 1×, 2×, 3×, 4×, 5× -50 ˚C (at 22 MHz) -65 ˚C -55 ˚C (11 MHz, 0.6875 MHz, Normal CCD readout) -65 ˚C (Room temperature: Stable at +20 ˚C ) -80 ˚C (Room temperature: Stable at +20 ˚C ) -65 ˚C (at 22 MHz) -80 ˚C -70 ˚C (11 MHz, 0.6875 MHz, Normal CCD readout) -80 ˚C (Water temperature: lower than +10 ˚C) -100 ˚C (Water temperature: lower than +10 ˚C) ±0.01 ˚C 0.01 electron/pixel/s 0.005 electron/pixel/s 0.0005 electron/pixel/s 0.001 electron/pixel/s 0.0015 events/pixel/frame 0.01 events/pixel/frame 13.9 ms to 1 s (22 MHz) 52.7 ms to 1 s (22 MHz) 27.2 ms to 2 h (11 MHz) 103.2 ms to 2 h (11 MHz) 421.5 ms to 2 h (0.6875 MHz) 1616.9 ms to 2 h (0.6875 MHz) 10 μs to 1 s (22 MHz) 10 μs to 2 h (11 MHz, 0.6875 MHz, Normal CCD readout) 16 bit IEEE1394b Every 16 lines (horizontal, vertical) size, position can be set 2×2, 4×4, 8×8, 16×16 *9 2×2, 4×4 Edge trigger, Level trigger, Start trigger, Synchronous readout trigger Exposure timing output, Programmable timing output (Delay and pulse length are variable.), Trigger ready output Background subtraction, Shading correction, Recursive filter, Frame averaging, Spot noise reducer EM warning mode, EM protection mode Available C-mount AC 100 V to 240 V, 50 Hz / 60 Hz Approx. 140 VA -10 ˚C to + 50 ˚C 0 ˚C to + 40 ˚C 0 ˚C to + 30 ˚C 70 % max. (with no condensation) *1 The hermetic sealed head maintains a high degree of vacuum, 10-8 Torr, without re-evacuation. *2 Even with electron multiplying gain maximum, dark signal is kept at a low level during low light imaging. *3 At 4×4 binning and 64×16 Sub-array *4 Linearity is not assured when full well capacity is over 370 000 electrons and 400 000 electrons, because of CCD performance. *5 The cooling temperature may not reach to this temperature; it depends on the operation condition. *6 Water volume 0.5 liter/min. *7 Typical thermal charge value (not guaranteed). *8 Image smearing may appear when the exposure time is short. *9 8 × 8 and 16 × 16 binning are available on special order. Please consult with our sales office. *10 C-MOS 3.3 V with reversible polarity. *11 Recursive filter, frame averaging, and spot noise reducer cannot be used simultaneously. Configuration example Video camera attachment (C-mount) ImagEM X2 EM-CCD camera set ImagEM X2-1K EM-CCD camera set ImagEM X2 ImagEM X2-1K W-VIEW GEMINI A12801-01 Microscope Computer frame grabber board Computer AC adapter Lens Water circulator Commercially available software HCImage Live software* Hose set A10788-04 * HCImage Live software provides standard image measurement functions. Upgrades to more feature-rich versions are available. Standard Option Please contact your local Hamamatsu representative or distributor regarding actual configuration. Dimensional outlines (Unit: mm) Camera (Approx. 3.5 kg) 110±1 111±1 55.5±1 215±2 25.5±1 4-M4 D=4 156±0.5 76±0.5 1-32UN C-mount D=5 Options *W-VIEW GEMINI Image Splitting Optics (Option) Binning option for C9100-23B: M10354-03 External trigger cable SMA-BNC 5 m: A12106-05 External trigger cable SMA-SMA 5 m: A12107-05 Hose set without joint: A10788-04 Base plate common for ImagEM X2 chassis: A12263-01 W-VIEW GEMINI Image Splitting Optics: A12801-01* The W-VIEW GEMINI is an image splitting optics which provides one pair of dual wavelength images separated by a dichroic mirror onto a single camera. Simultaneous image acquisition of dual wavelength images allows you high speed ratio metric imaging and other multiple fluorescence applications. ImagEM is registered trademark of Hamamatsu Photonics K.K. (EU, Japan, U.K., U.S.A.) HCIMAGE is registered trademark of PHOTONICS MANAGEMENT CORP. (Australia, China, EU, Japan, Norway, Singapore, Switzerland, U.S.A.) Product and software package names noted in this documentation are trademarks or registered trademarks of their respective manufacturers. ● Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult your local sales representative. ● Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications and external appearance are subject to change without notice. © 2015 Hamamatsu Photonics K.K. HAMAMATSU PHOTONICS K.K. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Systems Division 812 Joko-cho, Higashi-ku, Hamamatsu City, 431-3196, Japan, Telephone: (81)53-431-0124, Fax: (81)53-435-1574, E-mail: [email protected] U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J 08807, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: [email protected] Germany: Hamamatsu Photonics Deutschland GmbH.: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-265-8 E-mail: [email protected] France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: [email protected] United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court,10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, UK, Telephone: (44)1707-294888, Fax: (44)1707-325777 E-mail: [email protected] North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: [email protected] Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6 20020 Arese (Milano), Italy, Telephone: (39)02-93581733, Fax: (39)02-93581741 E-mail: [email protected] China: Hamamatsu Photonics (China) Co., Ltd.: B1201 Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86)10-6586-6006, Fax: (86)10-6586-2866 E-mail: [email protected] Cat. No. SCAS0092E05 MAY/2015 HPK Created in Japan