CPC1225N

CPC1225N
400V Normally-Open Single-Pole
4-Pin SOP OptoMOS® Relay
INTEGRATED CIRCUITS DIVISION
Parameter
Blocking Voltage
Load Current
On-Resistance (max)
Rating
400
120
30
Units
VP
mArms / mADC

Features
• 0.4mm Distance Through Insulation
(Supplementary Isolation Requirement of
EN60950)
• 1500Vrms Input/Output Isolation
• Small 4-Pin SOP Package
• Low Drive Power Requirements
• High Reliability
• Arc-Free With No Snubbing Circuits
• No EMI/RFI Generation
• Wave Solderable
• Tape & Reel Version Available
Description
The CPC1225N is a miniature normally-open,
single-pole, (1-Form-A) solid state relay that employs
IXYS Integrated Circuits Division’s patented, optically
isolated OptoMOS architecture to provide 1500Vrms
of input-to-output isolation. A highly efficient infrared
LED controls the optically coupled output. The device
also complies with the Supplementary Isolation
requirements of EN/IEC 60950-1.
The CPC1225N uses IXYS Integrated Circuits
Division’s state of the art double molded vertical
construction to produce one of the world’s
smallest 4-pin relays. It offers board space savings
approaching 20% over the competitor’s larger 4-pin
SOP relay.
Applications
• Telecommunications
• Telecom Switching
• Tip/Ring Circuits
• Modem Switching (Laptop, Notebook, Pocket
Size)
• Hook Switch
• Dial Pulsing
• Ground Start
• Ringing Injection
• Instrumentation
• Multiplexers
• Data Acquisition
• Electronic Switching
• I/O Subsystems
• Meters (Watt-Hour, Water, Gas)
• Medical Equipment-Patient/Equipment Isolation
• Security
• Aerospace
• Industrial Controls
Approvals
• UL Recognized Component: File E76270
• CSA Certified Component: Certificate 1172007
• EN/IEC 60950-1 Certified Component:
Certificate B 13 12 82667 003
Ordering Information
Part #
CPC1225N
CPC1225NTR
Description
4-Pin SOP (100/tube)
4-Pin SOP (2000/reel)
Pin Configuration
+ Control
– Control
1
4
3
2
Load
Load
Switching Characteristics
of Normally-Open Devices
Form-A
IF
90%
10%
ILOAD
ton
DS-CPC1225N-R06
www.ixysic.com
toff
1
INTEGRATED CIRCUITS DIVISION
CPC1225N
Absolute Maximum Ratings @ 25ºC
Parameter
Blocking Voltage (Peak)
Reverse Input Voltage
Input Control Current
Peak (10ms)
Input Power Dissipation
Total Power Dissipation 1
Isolation Voltage, Input to Output
Operational Temperature
Storage Temperature
1
Ratings
400
5
50
1
70
400
1500
-40 to +85
-40 to +125
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to the
device. Functional operation of the device at conditions beyond
those indicated in the operational sections of this data sheet is
not implied.
Units
VP
V
mA
A
mW
mW
Vrms
°C
°C
Typical values are characteristic of the device at +25°C, and
are the result of engineering evaluations. They are provided for
information purposes only, and are not part of the manufacturing
testing requirements.
Derate linearly 3.33 mW / ºC
Electrical Characteristics @ 25ºC
Parameter
Output Characteristics
Load Current
Continuous 1
Peak
On-Resistance 2
Off-State Leakage Current
Switching Speeds
Turn-On
Turn-Off
Output Capacitance
Input Characteristics
Input Control Current to Activate 3
Input Control Current to Deactivate
Input Voltage Drop
Reverse Input Current
Common Characteristics
Capacitance, Input to Output
1
2
3
2
Conditions
Symbol
Min
Typ
Max
Units
t=10ms
IL=120mA
VL=400VP
IL
ILPK
RON
ILEAK
-
20
-
120
±350
30
1
mArms / mADC
mAP

µA
IF=0mA, VL=50V, f=1MHz
ton
toff
COUT
-
1.25
0.35
9
2
1
-
IL=120mA
IF=5mA
VR=5V
IF
IF
VF
IR
0.3
0.9
-
0.6
0.55
1.2
-
2
1.4
10
mA
mA
V
µA
-
pF
IF=5mA, VL=10V
VIO=0V, f=1MHz
CIO
Load current derates linearly from 120mA @ 25oC to 80mA @ 85oC.
Measurement taken within 1 second of on-time.
For applications requiring high temperature operation (greater than 60°C) a minimum LED drive current of 4mA is recomended.
www.ixysic.com
1
ms
pF
R06
INTEGRATED CIRCUITS DIVISION
CPC1225N
PERFORMANCE DATA @ 25ºC (Unless Otherwise Noted)*
Typical LED Forward Voltage Drop
(N=50, IF=5mA)
25
Device Count (N)
Device Count (N)
30
25
20
15
10
5
0
25
20
15
10
5
1.22
1.23
1.24
15
10
0
1.25
0.80
0.95
LED Forward Voltage Drop (V)
1.10
1.25
1.40
1.55
0.29
1.70
Typical IF For Switch Dropout
(N=50, IL=120mA)
20
20
25
10
5
0
Device Count (N)
30
Device Count (N)
25
15
15
10
5
0.55
0.60
0.65
0.70
0.41
20
15
10
5
0
0.50
0.33 0.35 0.37 0.39
Turn-Off Time (ms)
Typical On-Resistance Distribution
(N=50, IF=2mA, IL=120mA)
25
0.45
0.31
Turn-On Time (ms)
Typical IF For Switch Operation
(N=50, IL=120mA)
Device Count (N)
20
5
0
1.21
Typical Turn-Off Time
(N=50, IF=5mA, IL=120mA)
30
Device Count (N)
35
Typical Turn-On Time
(N=50, IF=5mA, IL=120mA)
0
0.75
0.45
0.50
LED Current (mA)
0.55 0.60 0.65 0.70
LED Current (mA)
0.75
17.5
18.0
18.5 19.0 19.5 20.0
On-Resistance (:)
20.5
Typical Blocking Voltage Distribution
(N=50)
Device Count (N)
20
15
10
5
0
405
435
Typical Turn-Off Time
vs. LED Forward Current
(IL=120mA)
0.40
8
1.6
1.4
IF=50mA
1.3
IF=30mA
IF=20mA
IF=10mA
IF=5mA
1.2
1.1
-40
-20
0
20
40
60
80
Temperature (ºC)
100
120
Turn-Off Time (ms)
7
1.5
Turn-On Time (ms)
LED Forward Voltage Drop (V)
415 420 425 430
Blocking Voltage (VP)
Typical Turn-On Time
vs. LED Forward Current
(IL=120mA)
Typical LED Forward Voltage Drop
vs. Temperature
1.0
410
6
5
4
3
2
0.30
0.25
0.20
0.15
1
0
0.35
0
5
10
15
20
LED Forward Current (mA)
25
0.10
0
5
10
15
20
LED Forward Current (mA)
25
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please
contact our application department.
R06
www.ixysic.com
3
INTEGRATED CIRCUITS DIVISION
CPC1225N
PERFORMANCE DATA @ 25ºC (Unless Otherwise Noted)*
Typical Turn-Off Time vs. Temperature
(IL=80mA)
0.6
IF=2mA
1.4
IF=5mA
1.2
1.0
-20
0
20
40
60
Temperature (ºC)
80
0.4
0.3
IF=2mA
0.2
0.0
100
Typical IF For Switch Operation
vs. Temperature
(IL=80mA)
0.85
-40
0.80
0.80
-20
0
20
40
60
Temperature (ºC)
80
30
25
20
15
10
-40
100
Typical IF For Switch Dropout
vs. Temperature
(IL=80mA)
0.70
0.65
0.60
0.55
0.50
0.70
0.65
0.60
0.55
0.50
0.45
0.45
0.40
-40
0.40
-40
0
20
40
60
Temperature (ºC)
80
100
Typical Load Current
vs. Load Voltage
(IF=2mA)
150
Blocking Voltage (VP)
50
0
-50
-100
-150
-2
-1
0
1
20
40
60
Temperature (ºC)
2
3
80
70
100
-40
0.025
440
430
420
410
-20
0
20
40
60
Temperature (ºC)
0
20
40
60
Temperature (ºC)
80
100
Typical Leakage vs. Temperature
Measured Across Pins 3&4
(VL=400V)
0.020
0.015
0.010
Load Current (A)
20
10
0
10
100
Load Voltage (V)
80
100
0.000
-40
-20
0
20
40
60
Temperature (ºC)
80
100
Energy Rating Curve
30
1
-20
0.005
400
40
0.1
IF=2mA
90
0.030
390
-40
100
100
450
Output Capacitance
vs. Load Voltage
(IF=0mA, f=1MHz)
50
80
80
110
460
Load Voltage (V)
Output Capacitance (pF)
0
20
40
60
Temperature (ºC)
120
Typical Blocking Voltage
vs. Temperature
100
-3
-20
Leakage (PA)
-20
0
130
Load Current (mA)
0.75
-20
Typical Load Current
vs. Temperature
0.75
LED Current (mA)
LED Current (mA)
IF=5mA
0.1
0.8
-40
Load Current (mA)
0.5
On-Resistance (:)
1.6
Typical On-Resistance
vs. Temperature
(IF=10mA, IL=80mA)
35
0.7
Turn-Off Time (ms)
Turn-On Time (ms)
1.8
Typical Turn-On Time vs. Temperature
(IL=80mA)
1000
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10μs 100μs 1ms 10ms 100ms
1s
10s 100s
Time
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please
contact our application department.
4
www.ixysic.com
R06
INTEGRATED CIRCUITS DIVISION
CPC1225N
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to
the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product
evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper
operation of our devices when handled according to the limitations and information in that standard as well as to any
limitations set forth in the information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced
product performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according
to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.
Device
Moisture Sensitivity Level (MSL) Rating
CPC1225N
MSL 3
ESD Sensitivity
This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.
Soldering Profile
This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020
must be observed.
Device
Maximum Temperature x Time
Maximum Reflow Cycles
CPC1225N
260ºC for 30 seconds
3
Board Wash
IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to
remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as
an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary
if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used.
Cleaning methods that employ ultrasonic energy should not be used.
R06
www.ixysic.com
5
INTEGRATED CIRCUITS DIVISION
CPC1225N
MECHANICAL DIMENSIONS
CPC1225N
4.089 ± 0.203
(0.161 ± 0.008)
Recommended PCB Land Pattern
0.200 ± 0.025
(0.008 ± 0.001)
0.60
(0.0217)
6.096 ± 0.102
(0.240 ± 0.004)
3.810 ± 0.076
(0.150 ± 0.003)
0.432 ± 0.127
(0.017 ± 0.005)
5.60
(0.2205)
1.02 ± 0.025
(0.040 ± 0.001)
Pin 1
2.54 Typ
(0.100 Typ)
1.30
(0.0512)
2.184 Max
(0.086 Max)
2.54
(0.10)
Pin to package standoff:
0.0637 ± 0.0383
(0.0025 ± 0.0015)
0.762 ± 0.102
(0.030 ± 0.004)
Dimensions
mm
(inches)
0.381 TYP.
(0.015 TYP.)
CPC1225NTR Tape & Reel
330.2 Dia
(13.00 Dia)
Top Cover
Tape Thickness
0.102 Max
(0.004 Max)
W=12.00
(0.472)
B0=4.70
(0.185)
K0=2.70
(0.106)
K1=2.30
(0.091)
P=8.00
(0.315)
A0=6.50
(0.256)
User Direction of Feed
Dimensions
mm
(inches)
Embossed
Carrier
Embossment
NOTE: All dimensional tolerances per Standard EIA-481-2 except as noted
For additional information please visit our website at: www.ixysic.com
IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make
changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated
Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its
products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe
property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.
6
Specification: DS-CPC1225N-R06
©Copyright 2014, IXYS Integrated Circuits Division
OptoMOS® is a registered trademark of IXYS Integrated Circuits Division
All rights reserved. Printed in USA.
11/10/2014