Teccor® brand Thyristors 8 Amp Alternistor (High Commutation) Triac for LED dimmer application Q6008LH1LED Series RoHS Description Q6008LH1LED series is designed to meet low load current characteristics typical in LED lighting applications. By keeping holding current at 6mA maximum, this Triac series is characterized and specified to perform best with LED loads. The Q6008LH1LED series is best suited for LED dimming controls to obtain the lowest levels of light output with a minimum probability of flickering. Q6008LH1LED series is offered in the industry standard TO-220AB package with an isolated mounting tab that makes it best suited for adding an external heat sink. Features Agency Approval Agency Agency File Number Benefits • As low as 6mA max holding current • Provides full control of light out put at the extreme low end of load conditions. • UL recognized TO-220AB package • 2500V AC min isolation between mounting tab and active terminals • 110 °C rated junction • Improves margin of safe operation with less heat sinking required L Package: E71639 ® Main Features Symbol IT(RMS) VDRM /VRRM IGT Value Unit 8 A 600 V 10 mA temperature Schematic Symbol MT2 MT1 • di/dt performance of 70A/μs • Enable survivability of typically LED load operating characteristics • QUADRAC version includes intergrated DIAC • Simplicity of circuit design & layout Applications Excellent for AC switching and phase control applications such as heating, lighting, and motor speed controls. G Typical applications are AC solid-state switches, lighting controls with LED lamp loads, small low current motor in power tools, and low current motors in home/brown goods appliances. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Q6008LH1LED Series 1 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor (High Commutation) Triac for LED dimmer application Absolute Maximum Ratings Symbol Parameter IT(RMS) Test Conditions Value Unit TC = 80°C 8 A f = 50 Hz t = 20 ms 80 f = 60 Hz t = 16.7 ms 85 tp = 8.3 ms 30 A 2s RMS on-state current (full sine wave) Non repetitive surge peak on-state current (full cycle, TJ initial = 25°C) ITSM I 2t A I2t Value for fusing di/dt Critical rate of rise of on-state current f = 120 Hz TJ = 110°C 70 A/μs IGTM Peak gate trigger current tP ≤ 10 μs; IGT ≤ IGTM TJ = 110°C 1.6 A PG(AV) Average gate power dissipation TJ = 110°C IGT = 35mA 0.5 W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 110 °C Tstg TJ Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol IGT Test Conditions Quadrant I – II – III VD = 12V RL = 60 Ω VGT Value Unit 10 mA 1.3 V MIN. 0.2 V MAX. I – II – III VGD VD = VDRM RL = 3.3 kΩ TJ = 110°C I – II – III IH IT = 15mA MAX. 6 mA dv/dt VD = VDRM Gate Open TJ = 110°C MIN. 50 V/μs (dv/dt)c (di/dt)c = 4.3 A/ms TJ = 110°C MIN. 10 V/μs tgt IG = 100mA PW = 15µs IT = 11.3 A(pk) TYP. 4.0 μs Value Unit MAX. 1.60 V MAX. 500 μA Static Characteristics Symbol Test Conditions ITM = 11.3A tp = 380 µs VTM IDRM VDRM = VRRM IRRM TJ = 110°C Thermal Resistances Symbol Parameter Value Unit Rθ(J-C) Junction to case (AC) 2.8 °C/W Rθ(J-A) Junction to ambient 50 °C/W Q6008LH1LED Series 2 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor (High Commutation) Triac for LED dimmer application Figure 2: Normalized DC Gate Trigger Current for All Quadrants vs. Junction Temperature Figure 1: Definition of Quadrants ALL POLARITIES ARE REFERENCED TO MT1 3.5 MT2 POSITIVE (Positive Half Cycle) 3.0 (+) I GT GATE MT1 I GT MT1 REF - MT2 (-) I GT GATE (+) MT1 REF REF QII QI QIII QIV IGT (TJ = 25°C) I GT GATE MT2 IGT (-) + + IGT MT2 0.5 0.0 MT1 MT2 NEGATIVE (Negative Half Cycle) 2.0 1.0 I GT GATE - 2.5 1.5 Ratio of MT2 -65 -40 -15 REF 10 35 60 85 110 Junction Temperature (TJ)- ºC NOTE: Alternistors will not operate in QIV Note: Alternistors will not operate in QIV Figure 3: Normalized DC Holding Current vs. Junction Temperature Figure 4: Normalized DC Gate Trigger Voltage for All Quadrants vs. Junction Temperature 3.5 2.0 2.0 1.5 VGT (TJ = 25°C) VGT 2.5 1.5 1.0 Ratio of IH Ratio of IH (TJ = 25°C) 3.0 1.0 0.5 0.5 0.0 0.0 -65 -40 -15 10 35 60 85 -65 110 -40 -15 Junction Temperature (TJ)- ºC 35 60 85 110 Figure 6: Maximum Allowable Case Temperature vs. On-State Current (Standard / Alternistor Triac) Figure 5: Power Dissipation (Typical) vs. RMS On-State Current 18 130 16 120 14 Maximum Allowable Case Temperature (TC) - °C Average On-State Power Dissipation (PD(AV)) - Watts 10 Junction Temperature (TJ)- ºC 12 10 8 6 4 110 100 90 80 70 2 0 0 2 4 6 8 60 10 0 Q6008LH1LED Series 1 2 3 4 5 6 7 8 RMS On-State Current (IT(RMS)) - Amps RMS On-State Current (IT(RMS)) - Amps 3 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor (High Commutation) Triac for LED dimmer application Figure 7: On-State Current vs. On-State Voltage (Typical) Figure 8: Maximum Allowable Ambient Temperature vs. On-State Current 120 TC = 25°C 16 Maximum Allowable Ambient Temperature (TA) - °C Postitive or Negative Instantaneous On-State Current (iT) - Amps 20 12 8 4 0 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 FREE AIR RATING - NO HEATSINK 100 80 60 40 20 0.6 0.8 1.0 1.2 1.4 1.6 0.0 Postitive or Negative Instantaneous On-State Voltage (vT) - Volts 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 RMS On-State Current (IT(RMS)) - Amps Figure 9: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-Repetitive) On-State Current (ITSM) - Amps 100 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 10 1 1 10 100 1000 Surge Current Duration- Full Cycles Q6008LH1LED Series 4 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor (High Commutation) Triac for LED dimmer application Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Physical Specifications Ramp-up TL tL TS(max) Preheat TS(min) 25 Peak Temperature (TP) tP TP Temperature Reflow Condition tS time to peak temperature Time Environmental Specifications Test Terminal Finish 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Terminal Material Copper Alloy Specifications and Conditions AC Blocking (VDRM) Temperature Cycling Temperature/ Humidity Design Considerations High Temp Storage Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage Q6008LH1LED Series Ramp-do Ramp-down Thermal Shock Autoclave MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 110°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C 1008 hours; -40°C MIL-STD-750, M-1056 10 cycles; 0°C to 100°C; 5-min dwelltime at each temperature; 10 sec (max) transfer time between temperature EIA / JEDEC, JESD22-A102 168 hours (121°C at 2 ATMs) and 100% R/H Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E 5 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 8 Amp Alternistor (High Commutation) Triac for LED dimmer application Dimensions — TO-220AB (L-Package) — Isolated Mounting Tab TC MEASURING POINT O A E AREA (REF.) 0.17 IN2 Dimension 8.13 .320 P B C 13.36 .526 D 7.01 .276 F R G L H K Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). N J M MT1 MT2 GATE Inches Millimeters Min Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Product Selector Gate Sensitivity Quadrants Part Number I – II – III Q6008LH1LED 10 mA Type Package Alternistor Triac TO-220L Packing Options Part Number Marking Weight Packing Mode Base Quantity Q6008LH1LED Q6008LH1 2.2 g Bulk 500 Q6008LH1LEDTP Q6008LH1 2.2 g Tube Pack 500 (50 per tube) Part Numbering System Part Marking System TO-220 AB - (L Package) Q 60 08 L H1 LED DEVICE TYPE Q : Alternistor Triac LED LIGHTING APPLICATION VOLTAGE RATING 60 : 600V SENSITIVITY & TYPE H1: 10mA (QI, II & III) Q6008LH1 YMXXX CURRENT 08: 8A PACKAGE TYPE L : TO-220 Isolated ® Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code Q6008LH1LED Series 6 Revised: January 25, 2013 08:34 AM ©2013 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information.