D100ERW Series Low Cost, Miniature 1W SIP, Wide Input DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 1W Output Power • 2:1 Input Voltage Range • 1,500 VDC Isolation • Short Circuit Protected • Miniature SIP Case • Single & Dual Outputs • 1.0 MH MTBF • Industry Standard Pin-Out • Low Low Cost!! Input Parameter Conditions 5 VDC Input 12 VDC Input 24 VDC Input Input Voltage Range Min. 4.5 9.0 18.0 Typ. 5.0 12.0 24.0 Reverse Polarity Input Current Short Circuit Input Power Max. 9.0 18.0 36.0 1.0 1,500 Units Max. ±3.0 ±2.0 ±0.5 ±0.75 ±1.0 100 Units % % % % % mV P - P % %/°C VDC A mW Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation , Single Output Load Regulation , Dual Output Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Min. Vin = Min to Max Iout = 10% to 100% Iout = 10% to 100% See Note 1 Typ. ±1.0 ±1.0 ±0.2 ±0.5 ±0.5 25 120 ±0.03 Continuous with Autorecovery General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 500 VDC 100 kHz, 1V Iout = 100% Min. 1,500 1,000 Typ. Max. 550 Units VDC M pF kHz Max. +85 +125 Units °C °C 95 % 80 180 Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient 0.87 x 0.47 x 0.37 Inches (22.0 x 12.0 x 9.50 mm) Non-Conductive Black Plastic (UL94-V0) 0.19 Oz (5.5g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 1.0 Typ. Max. Units MHours Min. -0.7 -0.7 -0.7 Typ. Max. 11.0 22.0 40.0 300 1,800 Units Absolute Maximum Ratings Parameter T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Conditions Conditions Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 5 VDC Input 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C mW www.micropowerdirect.com Model Selection Guide Model Number D101ERW D102ERW D103ERW D104ERW D106ERW D107ERW D108ERW D111ERW D112ERW D113ERW D114ERW D116ERW D117ERW D118ERW D119ERW D121ERW D122ERW D123ERW D124ERW D125ERW D126ERW D127ERW D128ERW D129ERW Input Voltage (VDC) Current (mA) Voltage Nominal Range Full-Load No-Load (VDC) 5 4.5 - 9.0 303 40 3.3 5 4.5 - 9.0 286 40 5.0 5 4.5 - 9.0 273 40 12.0 5 4.5 - 9.0 277 40 15.0 5 4.5 - 9.0 282 40 ±5.0 5 4.5 - 9.0 273 40 ±12.0 5 4.5 - 9.0 273 40 ±15.0 12 9.0 - 18.0 122 20 3.3 12 9.0 - 18.0 111 20 5.0 12 9.0 - 18.0 106 20 12.0 12 9.0 - 18.0 106 20 15.0 12 9.0 - 18.0 111 20 ±5.0 12 9.0 - 18.0 108 20 ±12.0 12 9.0 - 18.0 110 20 ±15.0 12 9.0 - 18.0 108 20 ±24.0 24 18.0 - 36.0 60 10 3.3 24 18.0 - 36.0 57 10 5.0 24 18.0 - 36.0 53 10 12.0 24 18.0 - 36.0 55 10 15.0 24 18.0 - 36.0 54 10 24.0 24 18.0 - 36.0 55 10 ±5.0 24 18.0 - 36.0 54 10 ±12.0 24 18.0 - 36.0 53 10 ±15.0 24 18.0 - 36.0 53 10 ±24.0 Output Current Current (mA, Max) (mA, Min) 303.0 200.0 83.0 67.0 ±100.0 ±42.0 ±33.0 303.0 200.0 83.0 67.0 ±100.0 ±42.0 ±33.0 ±21.0 303.0 200.0 83.0 67.0 42.0 ±100.0 ±42.0 ±33.0 ±21.0 Notes: 1. When measuring output ripple, it is recommended that an external ceramic capacitor (approx. 1 µF to 10 µF) be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters are specified for operation without external components. However, in some applications the addition of Output Capacitor Input input/output capacitors Vin Vout 0 - 70ºC -40 - 85ºC will enhance stabilCapacitor (Electrolitic) (Tantalum) ity and reduce output 5 VDC 100 µF 47 µF ripple. Recommended 12 VDC 100 µF 12 VDC 100 µF 47 µF capacitor values are 15 VDC 100 µF given in the table at 24 VDC 10 µF 15 VDC 100 µF 47 µF right. Output ripple on single output units Output Voltage may be further enhanced by using 3.3V 5V 12V 15V 24V the CS terminal (single output units CS 47 µF - 100 µF 22 µF - 47 µF operated at 50% load or below should use this function). A low ESR capacitor is connected between the CS pin and the -Vout pin (the anode of the capacitor is connected to the -Vout pin). Recommended capacitor values are given in the table above. If not used, the CS pin should be left open. 4. Dual output units may be connected to provide a 10V, 24V, 30V or 48 VDC output. To do this, connect the load across the +Vout and -Vout outputs and float the output common. 5. The remote on/off control pin is referenced to Min Max the -Vin pin. Input current to the pin should be between 5 - 10 mA with a maximum of 20 mA. On <0.6 VDC to Open Circuit 6. It is recommended that a fuse be used on the Off 2.7 VDC 15.0 VDC input of a power supply for protection. See the Model Selection table above for the correct rating. Rating Efficiency Fuse Slow-Blow (%, Typ) (mA) 30.0 20.0 8.0 12.0 ±10.0 ±4.0 ±3.0 30.0 20.0 8.0 12.0 ±10.0 ±4.0 ±3.0 ±2.0 30.0 20.0 8.0 12.0 4.0 ±10.0 ±4.0 ±3.0 ±2.0 66 70 73 72 71 73 73 68 75 78 78 75 77 76 77 70 73 78 76 77 76 78 78 78 750 750 750 750 750 750 750 400 400 400 400 400 400 400 400 150 150 150 150 150 150 150 150 150 Derating Curve Mechanical Dimensions Pin Connections Pin Single Dual 1 -Vin -Vin 2 +Vin +Vin 3 Remote ON/OFF 5 NF NF 6 +Vout +Vout 7 -Vout Common 8 CS -Vout NF = No Function Mechanical Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]